2002-2008 Cupra Born SUV Safety -> Transporting children safely User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Safety -> Transporting children safely for Your Cupra Born SUV First Generation (2002-2008)

Safety  
The laws of physics involved and the forces  
acting in a collision apply also to children  
››› page 43. But unlike adults, children do not  
have fully developed muscle and bone struc-  
tures. This means that children are subject to a  
greater risk of injury.  
child seat. Adjust only the “SICT” closest to the  
door. Please follow the child seat manufactur-  
er's usage instructions).  
●
Any work on the head-protection airbag  
system or removal and installation of the air-  
bag components for other repairs (such as  
removal of the roof lining) should only be  
performed by a specialised workshop. Other-  
wise, faults may occur during the airbag sys-  
tem operation.  
●
Child seats directed towards the front of the  
vehicle (group 3): safety belt (TAKATA MAXI).  
Follow the manufacturer's instructions and ob-  
serve any statutory requirements when instal-  
ling and using child seats. Always read and note  
››› page 57.  
We recommend you always carry the manufac-  
turer's Child Seat Instruction Manual together  
with the on-board documentation.  
To reduce the risk of injuries, children must  
always use special child restraint systems when  
travelling in the vehicle.  
●
The side and head airbags are managed  
through sensors located in the interior of the  
front doors. To ensure the correct operation  
of the side and curtain airbags neither the  
doors nor the door panels should be modi-  
ꢀed in any way (e.g. ꢀtting loudspeakers). If  
the front door is damaged, the airbag system  
may not work correctly. All work carried out  
on the front door must be done in a special-  
ised workshop.  
We recommend the use of child safety  
products from the Original Accessories Pro-  
gramme, which includes systems for all ages  
made by “Peke” (not for all countries) (see  
www.seat.com).  
These systems have been especially designed  
and approved, complying with the ECE-R44.  
regulation.  
Child seats group classiꢀcation  
CUPRA recommends securing the child seats  
shown on the website as described below:  
Transporting children  
safely  
●
Child seats in the opposite direction of travel  
(group 0+): ISOFIX and support peg (ROMER  
BABY SAFE PLUS SHR II + ISOFIX BASE / PEKE  
G0 I-SIZE + I-SIZE BASE).  
Introduction  
For safety reasons, as we have learned from  
accident statistics, we recommend that chil-  
dren under 12 years of age travel in the rear  
seats. Depending on their age, height and  
weight, children travelling in rear seats must  
use a child seat or a seat belt. For safety rea-  
sons, the child seat should be installed in the  
rear seat, behind the front passenger seat or in  
the centre back seat.  
●
Child seats in the direction of travel (group  
1): ISOFIX and Top Tether (ROMER DUO PLUS +  
TOP TETHER / PEKE G1 TRIFIX I-SIZE).  
Fig. 50 Examples of child seats.  
●
Forward-facing child seats (group 2): seat  
Use only child seats that are oꢀicially approved  
and suitable for the child.  
belt and ISOFIX (ROMER BRITAX KIDFIX2 S.  
In addition, it is necessary to use the child  
seat attachment point for the waist strap “Se-  
cureGuard” and adjust the side impact protec-  
tion system “SICT”located at the rear of the  
These seats are subject to the ECE-R44 or  
ECE-R129 standards. ECE-R stands for: Eco-  
nomic Commission for Europe Regulation.  
56  
Transportingchildren safely  
Child seats by approval category  
Child seats by weight group  
Fitting and using child seats  
The child seats are grouped into 5 categories:  
Child seats may have the approval category of  
universal, semi-universal, vehicle speciꢁc (all  
according to the ECE-R44 standard) or i-Size  
(according to the ECE-R129 standard).  
Age group  
Group 0  
Group 0+  
Group 1  
Weight of the child  
Up to 10 kg  
●
Universal: child seats with universal approval  
can be installed in all vehicles. There is no need  
to consult any list of models. In the case of  
universal approval for ISOFIX, the child seat is  
additionally provided with a Top Tether belt.  
Up to 13 kg  
From 9 to 18 kg  
From 15 to 25 kg  
From 22 to 36 kg  
Group 2  
Group 3  
Fig. 51 Airbag sticker: on the passenger  
side sunshade blind.  
●
Semi-universal: semi-universal approval, in  
addition to the standard requirements of uni-  
versal approval, requires safety devices to lock  
the child seat, which require additional test-  
ing. Child seats with semi-universal approval  
include a list of vehicle models for which they  
can be installed.  
Warnings about ꢀtting a child seat  
Child seats that have been tested and ap-  
proved under the ECE R44 or ECE-R129 stand-  
ards bear the ECE-R44 or ECE-R129 test marks  
on the seat (the letter E in a circle with the test  
number below it).  
Take the following general warnings into ac-  
count if you are going to ꢁt a child seat. They  
are valid for all child seats regardless of their  
attachment system.  
●
Vehicle-speciꢀc: vehicle-speciꢁc approval  
requires a dynamic test of the child seat for  
each vehicle model separately. Child seats with  
vehicle-speciꢁc approval also include a list of  
vehicle models for which they can be installed.  
Follow the manufacturer's instructions and ob-  
serve any statutory requirements when instal-  
ling and using child seats.  
●
Please read and follow the child seat manu-  
facturer's operating instructions.  
●
The child seat should preferably be ꢁtted to  
We recommend you to always include the  
manufacturer's Child Seat Instruction Manual  
together with the on-board documentation.  
the rear seat behind the front passenger seat  
so that the child can exit the vehicle on the  
pavement side.  
●
i-Size: child seats with i-Size approval must  
meet the requirements prescribed in the ECE-  
R 129 standard in relation to installation and  
safety. Child seat manufacturers can tell you  
which seats have i-Size approval for this vehi-  
cle.  
CUPRA recommends you use child seats from  
the Original Accessories Catalogue. These  
child seats have been designed and tested for  
use in our vehicles. You can ꢁnd the right child  
seat for your model and age group at our deal-  
ers.  
●
Set the height of the seat belt such that  
it adapts to the child seat naturally, without  
twisting. The lowest position of the seat belt  
height regulator must be used with rear-facing  
child seats.  
●
To correctly use a child seat in the back, the  
front backrest must be adjusted so that there  
is no contact with the child seat in the back in  
57  
Safety  
●
the case that it goes opposite to the direction  
of the car. In the case of front facing restraint  
systems, the front backrest must be adjusted  
so that there is no contact with the child's feet.  
Safety distance with respect to the passenger  
●
Never install a child seat facing backwards  
airbag ››› page 48.  
●
on the front passenger seat unless the  
front passenger front airbag has been dis-  
abled. Risk of potentially fatal injuries to  
the child! However, if necessary, the front  
passenger front airbag must be deactivated  
Objects between the passenger and the pas-  
senger side airbag ›››  
in Front airbags on  
●
For a correct assembly of the child's seat on  
page 52.  
the rear seats, adjust or dismount the head-  
rest, in order to prevent contact with the seat.  
The passenger side front airbag, when ena-  
bled, is a serious risk for a child that is facing  
backward since the airbag can strike the seat  
with such force that it can cause serious or  
fatal injuries. Children up to 12 years old should  
always travel on the rear seat.  
››› page 52 . If the passenger seat has  
a height adjustment option, move it to the  
highest, most upright position. If you have a  
ꢀxed seat, do not install any child restraint  
system in this location.  
●
If a semi-universal type chair is to be instal-  
led, in which the method of attachment to  
the car is through the seat belt and support  
bracket, it should never be installed in the cen-  
tral rear seat as the ground clearance is lower  
than in other places and the support bracket  
will not allow the seat to remain suꢀiciently sta-  
ble.  
●
For those vehicles that do not include a key  
lock switch to deactivate the airbag, the vehi-  
cle must be taken to a technical service. Do  
not forget to reconnect the airbag when an  
adult wants to sit in the front passenger seat.  
Therefore we strongly recommend you to  
transport children on the rear seats. This is the  
safest location in the vehicle. Alternatively, the  
front passenger airbag can be disabled with a  
key-operated switch ››› page 52. When trans-  
porting children, use a child seat suitable for  
the age and size of each child ››› page 56.  
●
When ꢁtting a child seat on the front passen-  
●
Never allow a child to be transported in a  
ger seat, the seat must be moved backwards as  
far as possible and placed in the highest posi-  
tion. The backrest must also be put in a vertical  
vehicle without being properly secured, or  
to stand up or kneel on a seat while travel-  
ling. In an accident, the child could be ꢁung  
through the vehicle, causing possibly fatal in-  
juries to themselves and to the other vehicle  
occupants.  
position1)  
.
WARNING  
Important information about the front pas-  
senger front airbag  
●
If a child seat is secured to the front pas-  
●
Never leave a child alone in the child seat  
senger seat, the risk to the child of sustaining  
critical or fatal injuries in the event of an ac-  
cident increases.  
or in the vehicle.  
A sticker with important information about the  
passenger airbag is located on the passenger's  
sunshade blind and/or on the passenger side  
door frame ››› Fig. 51.  
Read and always observe the safety informa-  
tion included in the following chapters:  
●
Children who are less than 1.50 m tall must  
not wear a normal seat belt without a child  
seat, as this could cause injuries to the ab-  
dominal and neck areas during a sudden  
braking manoeuvre or in an accident.  
●
An inꢁating front passenger airbag can  
strike the rear-facing child seat and project  
it with great force against the door, the roof  
or the backrest.  
●
When a child seat is mounted in the rear  
seats, the door child-proof lock should be  
activated ››› page 100.  
1)  
Compliance with current national legislation and the manufacturer's instructions is required when using or installing child seats.  
58  
Transportingchildren safely  
the luggage compartment side ››› page 62.  
The rings for retaining the Top Tether belt are  
marked with an anchor symbol.  
Attachment systems  
ted with objects. In addition, make sure that  
the base of the child seat is always supported  
by the surface of the vehicle's seat. The sup-  
port leg of the child seat should not raise the  
base of the child seat oꢂ the surface of the  
vehicle's seat.  
Depending on the country, diꢀerent attach-  
ment systems are used for safely installing child  
seats.  
●
Support bracket: some child seats rest on  
the ꢂoor of the vehicle with a support bracket.  
The support bracket prevents the child seat  
from tipping forward in the event of impact.  
Child seats ꢁtted with a support bracket should  
only be used in the passenger seat and side  
Attachment systems overview  
●
ISOFIX: ISOFIX is a standardised attachment  
Securing the child seat with the  
ISOFIX or i-Size system  
system allowing quick and safe attachment of  
child seats in the vehicle. ISOFIX attachment  
establishes a rigid connection between the  
child seat and the car body.  
rear seats ››› . For the assembly of this type  
of seat you should also consult the list of ap-  
proved vehicles for this assembly, available in  
the instructions for child restraint systems.  
The marking of ISOFIX or i-Size anchor points  
depends on the equipment and the country in  
question.  
The child seat has two rigid attachment clips,  
called connectors. These connectors are ꢁt-  
ted into the ISOFIX attachment rings found  
between the seat cushion and the backrest  
of the vehicle's back seat (on the sides). ISO-  
FIX attachment systems are used mainly in Eu-  
See the following tables to understand the  
compatibility of the ISOFIX/i-Size systems in  
the vehicle:  
Recommended systems for attaching child  
seats  
CUPRA recommends attaching child seats as  
follows:  
rope ››› page 59. If necessary, ISOFIX at-  
tachment may have to be supplemented with a  
Top Tether belt or a support bracket.  
●
Baby carriers or child seats in the oppo-  
site direction of travel: ISOFIX and support  
bracket or i-Size.  
●
Automatic three-point seat belt. Whenever  
●
Child seats in the direction of travel: ISOFIX  
possible, it is preferable to attach the child  
seats with the ISOFIX system rather than at-  
taching them with an automatic three-point  
and Top Tether.  
seat belt ››› page 63.  
WARNING  
Additional attachment:  
Incorrect use of the support bracket can  
cause serious or fatal injury.  
●
Top Tether: the Top Tether belt is guided  
over the back of the rear seat and attached to  
an anchor point with a hook. Anchor points are  
located at the back of the rear seat backrest on  
●
Make sure the support bracket is correctly  
and safely installed.  
●
When the base of the child seat is sup-  
porting the child’s weight, the support foot  
should not hang in the air or be supplemen-  
59  
Safety  
Vehicle ISOFIX positions  
Weight group  
Front passenger seat  
Electrical  
equipment  
Size classa)  
Rear side seat  
Rear central seat  
airbag enabled  
airbag disabled  
F
ISO/L1  
ISO/L2  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Baby carrier  
G
X
IL  
X
IL  
Group 0 to 10 kg  
E
ISO/R1  
E
ISO/R1  
IL  
IL  
Group 0+ to 13 kg  
Group I 9 to 18 kg  
D
C
ISO/R2  
IL  
IL  
SO/R3  
IL  
IL  
D
ISO/R2  
IL  
IL  
C
ISO/R3  
IL  
IL  
B
ISO/F2  
IL, IUF  
IL, IUF  
IL, IUF  
IL  
IL, IUF  
IL, IUF  
IL, IUF  
IL  
B1  
ISO/F2X  
ISO/F3  
A
Group II 15 to 25 kg  
Group III 22 to 36 kg  
B2/B3  
B2/B3  
ISO/B2/B3b)  
ISO/B2/B3b)  
IL  
IL  
IUF: Suitable for forward-facing ISOFIX universal child restraint systems approved for use in this weight group.  
IL: It is suitable for certain ISOFIX child restraint systems (CRS) that can be for the speciꢀc vehicle, restricted or semi-universal categories. Take the  
child seat manufacturer's vehicle list into account.  
X: ISOFIX position not suitable for ISOFIX child restraint systems for this weight group or size class.  
a) The indication of class according to size corresponds to the authorised bodyweight for the child seat. In child seats with universal or semi-universal approval, the  
class according to size is indicated on the ECE approval label. The indication of class according to size is stated on the corresponding child seat.  
b) The headrest must be removed and the backrest reclined to install it on front seats.  
60  
Transportingchildren safely  
Vehicle i-Size positions  
Front passenger seat  
Rear side seat  
i-U  
Rear central seat  
airbag enabled  
airbag disabled  
X
i-U  
X
i-U: Position suitable for forward- or rear-facing i-Size child restraint systems with universal certiꢀcation.  
X: Position not suitable for i-Size child restraint systems.  
Securing the child seat with the ISOFIX or  
i-Size system  
Fig. 54 Rear seats: ꢀtting a child seat with  
Fig. 53 Front passenger seat: location of  
the ISOFIX system.  
the i-Size fastening rings.  
Fig. 52 Rear seat: location of the ISOFIX or  
i-Size securing rings.  
You must follow the child seat manufacturer's  
instructions.  
The location of the ISOFIX or i-Size anchor  
points is indicated by a symbol ››› Fig. 52 ,  
››› Fig. 531). In some vehicles, the rings are  
secured to the seat frame and, in others, they  
are secured to the rear ꢂoor.  
1)  
Not available on all markets.  
61  
Safety  
●
If necessary, remove the protective caps  
Top Tether securing belts  
from the ISOFIX or i-Size anchor points.  
●
Press the child seat onto the ISOFIX or iSize  
retaining rings until it is heard to engage se-  
curely ››› Fig. 54. If the child seat is equipped  
with Top Tether anchor points, secure it to the  
correspondent ring ››› page 62. Follow the  
child seat manufacturer’s instructions.  
●
Pull on both sides of the child seat to ensure  
that it is properly anchored.  
Fig. 57 Rear part of the rear seats: Top  
Tether strap anchor.  
Child seats with the ISOFIX or i-Size and Top  
Tether attachment system can be purchased  
from technical services.  
Fig. 55 Rear seats: adjustment and  
assembly according to the Top Tether belt.  
WARNING  
The securing rings are designed only for use  
with ISOFIX or i-Size and Top Tether system  
child seats.  
●
Never secure other child seats that do not  
have ISOFIX, i-Size or Top Tether systems, or  
safety belts or any other objects to the se-  
curing rings – as this can result in potentially  
fatal injuries to the child.  
Fig. 58 Rear of front passenger seat  
backrest: Top Tether strap anchor (not  
available on all markets).  
●
Ensure that the child seat is correctly se-  
cured to the ISOFIX or i-Size rings and the  
Top Tether.  
Fig. 56 Passenger seat: adjustment and  
assembly according to the Top Tether belt.  
Child seats with a Top Tether system are ꢁtted  
with an additional strap for fastening to an an-  
chor point in the vehicle. This anchor point  
is located on the rear of the rear seat back-  
62  
Transportingchildren safely  
Releasing the retaining strap  
rest and of the front passenger seat backrest  
1) (identiꢁed with the symbol ) and provides  
better retention.  
Fitting a child seat using the seat  
belt  
●
Loosen the strap following the manufactur-  
er's instructions.  
If you want to ꢁt a universal approval category  
(U) child seat in your vehicle, you must check  
that the seat is approved for your vehicle.  
The objective of this system is to reduce for-  
ward movements of the child seat in a head-on  
collision, to reduce the risk of injuries that may  
be caused to the child’s head by impacting  
against any element of the inside of the vehi-  
cle.  
●
Push the lock and release it from the anchor-  
ing support.  
You will ꢁnd any necessary information on the  
child seat’s orange ECE approval label.  
WARNING  
An undue installation of the safety seat will  
increase the risk of injury in the event of a  
crash.  
The following table shows the diꢀerent ꢁtting  
options.  
Using the Top Tether in rear-facing mounted  
seats  
●
Never tie the retainer strap to a hook in the  
luggage compartment.  
Currently, there are very few rear-facing child  
safety seats that have Top Tether. Please care-  
fully read and follow the seat manufacturer in-  
structions to learn the proper way to install the  
Top Tether strap.  
●
Never secure or tie luggage or other items  
to the lower anchorages (ISOFIX) or the up-  
per ones (Top Tether).  
WARNING  
Securing the retainer strap  
Child restraint anchors are designed to sup-  
port the loads of properly adjusted child  
restraint systems. Under no circumstances  
should they be used to attach adult seat  
belts, harnesses or other items or equipment  
to the vehicle.  
●
Follow the manufacturer's instructions to de-  
ploy the child seat Top Tether retaining strap.  
●
Position the belt under the headrest (ac-  
cording to the instructions of the seat it-  
self, lift or remove the headrest if necessary)  
››› Fig. 55 , ››› Fig. 56.  
●
Slide the strap and secure it properly with the  
anchor on the rear seat backrest ››› Fig. 57 ,  
››› Fig. 58.  
●
Firmly tighten the strap following the manu-  
facturer's instructions.  
1)  
Not available on all markets.  
63  
Safety  
Front passenger seata)  
Weight group  
Rear side seat  
Rear central seatb)  
Airbag enabled  
Airbag deactivatedc)  
Group 0 to 10 kg  
Group 0+ to 13 kg  
Group I 9 to 18 kg  
Group II 15 to 25 kg  
Group III 22 to 36 kg  
X
X
X
X
X
U
U
U
U
U
U
U
U
U
UF  
UF  
UF  
UF  
UF  
UF  
X: Not compatible for the installation of seats install chairs in this conꢀguration.  
U: Suitable for universal restraint systems for use in this weight group.  
UF: Acceptable for front-facing universal-category child restraint systems approved for this mass group.  
a) Compliance with current national legislation and the manufacturer's instructions is required when using or installing child seats.  
b) For semi-universal chairs where the securing system is the car safety belt and the support bracket, do not use them in the centre rear seat.  
c) Seats without height adjustment should be placed in their rearmost position. Seats with height adjustment should be placed in their rearmost and highest  
position.  
●
Put the seat belt in place and pass it through  
Fitting a child seat using the seat belt  
WARNING  
the child seat according to the instructions of  
the child seat manufacturer.  
When travelling, children must be secured in  
the vehicle with a restraint system suitable  
for age, weight and size.  
●
●
Make sure that the seat belt is not twisted.  
Insert the latch plate into the seat's buckle  
●
Always read and observe information and  
warnings concerning the use of child seats  
until you hear the engagement click.  
››› page 57.  
Fig. 59 On rear seats: installing a child seat.  
64  

Related Topics

Popular Owner Manuals