2024-2026 Cupra Terramar SUV Storing objects -> Trailer mode User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Storing objects -> Trailer mode for Your Cupra Terramar SUV First Generation (2024-2026)

322
Storing objects
Loading the roof carrier system
The load can only be secured if the crossbars
and the roof carrier system are properly instal-
led›››
.
Maximum authorised cargo on the roof
The maximum permissible roof load is 75kg.
This gure comes from the combined weight
of the roof carrier, the cross bars and the load
itself on the roof ››› .
Always check the weight of the roof carrier sys-
tem (roof box, bicycle carrier, ski rack, etc.), of
the cross bars and of the load to be transpor-
ted and weigh them if necessary. Never exceed
the maximum authorised roof load.
If you are using cross bars and a roof carrier
with a lower weight rating, you will not be able
to carry the maximum authorised roof load. In
this case, do not exceed the maximum weight
limit for the roof carrier which is listed in the
tting instructions.
Distributing a load
Distribute loads uniformly and secure them
correctly ››› .
Check attachments
Once the cross bars and roof carrier system
have been installed, check the bolted connec-
tions and attachments after a short journey
and every so often afterwards (approx. every
200km).
WARNING
●
Never exceed the maximum authorised
load on the roof and on the axles or the vehi-
cle's maximum authorised weight.
●
Never exceed the load capacity of the cross
bars and the roof carrier system, even if the
maximum authorised roof load has not been
reached.
●
Secure heavy items as far forward as possi-
ble and distribute the vehicle load uniformly.
WARNING
If the load is loose or not secured, it could
fall from the roof carrier system or cause ac-
cidents and injuries.
●
Always use belts or retaining straps that are
suitable and in a good condition.
Trailer mode
Introduction
Take into account country-specic regulations
about driving with a trailer and the use of a
towing bracket.
The vehicle has been developed primarily for
carrying people, although it can also be used
to tow a trailer if tted with the corresponding
technical equipment. This additional load has
an eect on the useful life, fuel consumption
and vehicle performance and in some cases
can reduce the service intervals.
Driving with a trailer requires more force from
the vehicle, and thus more concentration from
the driver.
In winter, winter tyres should be tted on both
the vehicle and the trailer.
Maximum vertical load technically permitted
on the coupling device
The maximum vertical load technically permit-
ted from the trailer draw bar on the towing
bracket's tow ball is 80kg.
Vehicles with the Start-Stop system
If the vehicle has a factory-tted towing
bracket or one that is retrotted by CUPRA,
the Start-Stop system operates as normal. No
special characteristics need to be taken into
account.
Storing objects
323
Trailer mode
If the system does not recognise the trailer or
the trailer bracket has not been retrotted by
CUPRA, the Start-Stop system must be discon-
nected by pressing the corresponding button
in the lower part of the centre console before
driving with the trailer, and it should remain o
for the rest of the journey››› .
Vehicles with driving prole selection
If you are going to be towing a trailer, the use
of the Eco driving prole is not recommended.
You are advised to select another of the avail-
able driving proles before beginning to drive
with a trailer.
Trailer weight/drawbar load
Never exceed the authorised trailer weight. If
you do not load the trailer up to the maximum
permitted trailer weight, you can then climb
correspondingly steeper slopes.
The maximum trailer weights listed are only
applicable for altitudes up to 1000m above
sea level. Since higher altitude decreases en-
gine performance and the ability to climb
slopes, the tow load decreases proportionally.
The weight of the vehicle and trailer combina-
tion must be reduced by 10% for every 1000m
of altitude. When possible, operate the trailer
with the maximum authorised drawbar load
on the ball joint of the towing bracket, but do
not exceed the specied limit.
WARNING
Never use the trailer to transport people,
since it would put their life in danger and is
also prohibited.
WARNING
Undue use of the towing bracket may cause
injury and accidents.
●
Only use the towing bracket if it is in a per-
fect state of repair and is properly secured.
●
Never modify or repair the towing bracket
in any way.
●
In order to reduce the danger of injury in
the event of rear-end collisions and to avoid
injury to pedestrians and cyclists when park-
ing the vehicle, cover or remove the tow
hook when you are not using a trailer.
●
According to EU regulation 2021_535 it is
not permitted to install a towing device that
completely or partially covers the rear num-
ber plate.
●
Never t a towing bracket “with weight dis-
tribution” or “load compensation”. The vehi-
cle has not been designed for this type of
towing bracket. The towing bracket could fail
and the trailer could be released from the
vehicle.
WARNING
Driving with a trailer and transporting heavy
or large objects can aect driving properties
and even cause an accident.
●
Always secure the load properly using belts
or straps that are suitable and in good condi-
tion.
●
Adapt your speed and driving style at all
times to suit visibility, weather, road and traf-
c conditions.
●
Trailers with a high centre of gravity are
more likely to overturn than those with a low
one.
●
Avoid sudden braking and manoeuvres.
●
Take great care when overtaking.
●
Reduce speed immediately if you notice
that the trailer is swaying, however slightly.
●
Never drive at more than 80km/h
(50mph) when towing a trailer (or at more
than 100km/h (60mph) in exceptional cir-
cumstances). This also applies in countries
where driving at higher speeds is permitted.
Take into account the speed limit for vehicles
with trailers in the corresponding country, as
it could be less than the speed limit for vehi-
cles without a trailer.
●
Never attempt to “straighten” the towing
vehicle and trailer while accelerating.
324
Storing objects
WARNING
If the towing bracket has been retrotted by
a non-CUPRA workshop, the Start-Stop sys-
tem must be disconnected manually when-
ever driving with a trailer. Otherwise the
brake system could be damaged and could
consequently cause a serious accident or in-
jury.
●
Always disconnect the Start-Stop system
manually when using a towing bracket that
has not been tted by a CUPRA workshop.
Note
●
Before hitching or unhitching a trailer,
always deactivate the anti-theft alarm
›››
page108. Otherwise, the tilt sensor
could cause the alarm to go o.
●
Do not drive with a trailer for the engine's
rst 1000km ›››
page164.
●
CUPRA recommends that, if possible, the
tow hook be removed or covered when it
is not going to be used. In the event of a
rear-end collision, the damage to the vehicle
could be greater if the tow hook is tted.
●
Some retrotted towing brackets cover the
rear towing eye. In these cases, the towing
eye should not be used for tow-starting or
for towing other vehicles. For this reason, if
the vehicle has been retrotted with a towing
bracket, always keep the tow hook in the ve-
hicle when you remove it.
Technical requirements
Vehicles that are factory-equipped with a tow-
ing bracket meet all the technical and legal re-
quirements for driving with a trailer.
If the vehicle is retrotted with a tow bracket,
only a bracket that is authorised for the maxi-
mum authorised load of the trailer that is to
be towed may be tted. The towing bracket
must be suitable for the vehicle and the trailer
and must be properly secured to the vehicle's
chassis. Only use a towing bracket that has
been authorised by CUPRA for this vehicle. Al-
ways check and take into account the towing
bracket manufacturer's instructions.
Towing bracket tted on the bumper
Never t a towing bracket to the bumper or to
the area where the bumper is mounted. The
towing bracket should not impair the bumper's
function. Do not make modications or repairs
to the exhaust system or the brake system.
Make regular checks to ensure that the towing
bracket is secure.
Engine cooling system
Driving with a trailer increases the load on
the engine and cooling system. The cooling
system should have suicient coolant and be
prepared for the additional eort involved in
driving with a trailer.
Trailer brakes
If the trailer has its own brake system, please
take the relevant legal requirements into ac-
count. Never connect the trailer's brake system
to the vehicle's brake system.
Tow cable
Always t a cable between the vehicle and the
trailer ›››
page325.
Trailer tail lights
The trailer's tail lights should comply with the
statutory safety regulations ›››page325.
Never connect the trailer's tail lights directly
to the vehicle's electric system. If you are not
sure that the trailer's electrical connection is
correct, have it checked by a specialised work-
shop. CUPRA recommends going to a special-
ised CUPRA dealer or any SEAT dealership for
this purpose.
Exterior mirrors
If you cannot see the area behind the trailer
with the exterior mirrors of the towing vehicle,
additional mirrors will have to be installed in
accordance with the regulations of the coun-
try in question. The exterior mirrors should be
adjusted before you start driving and must pro-
vide a suicient eld of vision at the rear.
Storing objects
325
Trailer mode
WARNING
If the towing bracket is tted incorrectly or is
not the right one, the trailer could become
detached from the vehicle and cause serious
injury.
NOTICE
●
If the tail lights of the trailer are not
correctly connected, the vehicle's electronic
system may be damaged.
●
If the trailer absorbs excessive electric cur-
rent, the vehicle's electronic system may be
damaged.
●
Never connect the trailer's electric system
directly to the electrical connections of the
tail lights or any other power sources. Only
use the connections intended for providing
electric current to the trailer.
Hitching and connecting a trailer
Fig.196 Diagram: assignment of the pins
of the trailer's electrical socket.
Pin Meaning
1 Left turn signal
2 Rear fog light
3 Earth for pins 1, 2, 4, 5, 6, 7 and 8
4 Right turn signal
5 Rear light, right
6 Brake lights
7 Rear light, left
8 Reverse lights
9 Permanent live
10 Live charge cable
11 Earth for pin 10
12 Unassigned
Pin Meaning
13 Earth for pin 9
Power socket for trailer
The vehicle is tted with a 13-pole power
socket for the connection between the trailer
and the vehicle. With the engine running, elec-
trical devices on the trailer receive power from
the electrical connection (pin 9 and pin 10 of
the trailer power socket).
If the system detects that a trailer has been
connected, the consumers on the trailer will
receive electricity through this connection
(pins 9 and 10). Pin 9 has a permanent live.
This powers, for example, the trailer's interior
lighting. Electrical devices such as a fridge in
a caravan only receive electrical power if the
engine is running (through pin 10).
To avoid overloading the electrical system, you
cannot connect the ground wires of pin 3, pin
11 or pin 13.
If the trailer has a 7-contact connector, you
will need to use an adapter cable. In this case
the function corresponding to pin 10 will not
be available.
326
Storing objects
Tow cable
The tow rope must always be securely xed to
the towing vehicle and loose enough so that
the vehicle can handle turns smoothly. How-
ever, make sure that the cable does not rub on
the ground while driving.
Trailer tail lights
Always check the trailer's rear lights to ensure
they are working correctly and that they com-
ply with the relevant safety regulations. If you
connect the trailer to the factory-mounted
system, when you turn on the rear fog lamp,
the fog lamp of the towing vehicle will turn o
to turn on the trailer fog lamp.
Include in the anti-theft alarm
The trailer is included in the anti-theft system if
the following conditions are met:
●
If the vehicle is factory-equipped with an
anti-theft alarm.
●
If the vehicle is factory-equipped with a tow
bracket.
●
If the trailer is electrically connected to
the towing vehicle through the trailer power
socket.
●
If the electrical systems of the vehicle and
trailer are in perfect condition and have no
faults or damage.
●
If the vehicle is locked with the key and the
anti-theft alarm is activated.
When the vehicle is locked, the alarm is trig-
gered if the electrical connection with the
trailer is cut o.
Before hitching or unhitching a trailer, always
turn o the anti-theft alarm. Otherwise, the tilt
sensor could cause the alarm to go o.
Trailers with LED tail lights
For technical reasons, trailers tted with LED
rear lights cannot be connected to the anti-
theft alarm system.
When the vehicle is locked, the alarm does not
go o when the electrical connection with the
trailer is cut if it has rear lights with light-emit-
ting diodes.
WARNING
If the cables are improperly or incorrectly
connected, it may lead to an excessive
amount of current supplied to the trailer,
which can cause abnormalities in the entire
vehicle electronic system, as well as acci-
dents and serious injuries.
●
Ensure that any repairs that need to be
carried out on the electrical system are car-
ried out by a specialised workshop.
●
Never connect the trailer's electric system
directly to the electrical connections of the
tail lights or any other power sources.
WARNING
Contact between the pins of the trailer power
socket can cause short circuits, overloading
of the electrical system or failure of the light-
ing system, and consequently can cause ac-
cidents and serious injuries.
●
Never connect the pins of the trailer power
socket to each other.
●
Make sure any work on bent pins is carried
out by a specialised workshop.
NOTICE
Do not leave the trailer connected to the
vehicle when parked; place it on its support
wheel or its supports. If the vehicle rises or
falls due, for example, to a variation of the
load or a burst tyre, increased pressure will
be placed on the towing bracket and the
trailer, and both the vehicle and the trailer
can be damaged.
Note
●
In case of anomalies in the electrical sys-
tems of the vehicle or trailer, as well as in the
anti-theft alarm system, have them inspec-
ted by a specialised workshop.
●
If the trailer accessories consume energy
through the power socket to the trailer and
the engine is turned o, the battery will dis-
charge.
Storing objects
327
Trailer mode
●
If the vehicle battery is running low, the
electrical connection with the trailer will be
automatically cut.
Trailer loading
Technically permissible maximum trailer
weight and vertical load on the coupling de-
vice
The technically permissible maximum trailer
weight is the weight that the vehicle can tow
›››
. The vertical load on the coupling is
exerted vertically from above on the ball of the
towing bracket.
The information on the maximum trailer
weight and vertical load on the coupling de-
vice contained in the type plate of the towing
bracket are experimental values only. The cor-
rect gures for your specic model, which may
be lower than these gures, are given in the
vehicle documentation. The information in the
vehicle documentation takes precedence at all
times.
To promote safety while driving, CUPRA rec-
ommends making the most of the maximum
technically permitted vertical load on the cou-
pling device ›››page322. An insuicient verti-
cal load has a negative inuence on the behav-
iour of both the vehicle and trailer.
The vertical load increases the weight on the
rear axle, reducing the vehicle's carrying ca-
pacity.
Gross combination weight of the towing ve-
hicle and trailer
The gross combination weight is the actual
weight of the loaded vehicle plus the actual
weight of the loaded trailer.
In some countries trailers are classied into
dierent categories. CUPRA recommends ob-
taining information from a specialised work-
shop regarding which type of trailer is most
suitable for your vehicle.
Trailer loading
The weight of the towing vehicle and trailer
must be balanced. In order to do this, the load
must be as close as possible to the maximum
technically permitted vertical load on the cou-
pling point, and it must be evenly distributed
between the back and front of the trailer:
●
Distribute loads in the trailer so that heavy
objects are as near to the axle as possible or
above it.
●
Secure the trailer load properly.
Tyre pressure
Set the tyre pressure of the trailer tyres in ac-
cordance with the trailer manufacturer's rec-
ommendations.
When towing a trailer, inate the tyres of the
towing vehicle to the maximum allowable pres-
sure ›››
page376.
WARNING
If the maximum permissible axle weight, the
maximum load technically permissible on the
coupling point, the maximum authorised ve-
hicle weight or the gross combination weight
of the towing vehicle and trailer are excee-
ded, accidents and serious injuries may oc-
cur.
●
Never exceed the indicated values.
●
The actual weight on the front and rear
axles must never exceed the maximum per-
missible axle weight. The weight on the front
and rear axles must never exceed the maxi-
mum permissible weight.
WARNING
A shift in weight could jeopardize the stability
and safety of the towing vehicle and trailer,
which could lead to accidents and serious in-
juries.
●
Always load the trailer correctly.
●
Always secure the load properly using belts
or straps that are suitable and in good condi-
tion.
Driving with a trailer
Adjusting the headlights
The front part of the vehicle may be raised
when the trailer is connected and the light may
dazzle the rest of the traic.
328
Storing objects
Specic features of driving with a trailer
●
If your trailer has an overrun brake, brake
gently at rst and then rapidly. This will prevent
the jerking that can be caused by the locking
of trailer wheels.
●
Due to the gross combination weight of the
towing vehicle and trailer, the braking distance
increases.
●
Use engine braking when descending hills.
Otherwise, the brake system could overheat
and even fail.
–
Vehicles with an automatic gearbox: In Tip-
tronic mode, select a lower gear.
●
The trailer weight, as well as the gross combi-
nation weight of the towing vehicle and trailer,
change the centre of gravity and the proper-
ties of the vehicle.
●
If the towing vehicle is empty and the trailer
is loaded, then the load distribution is incor-
rect. Under these conditions, drive slowly and
with extra caution.
Hill starts with a trailer
Depending on the slope of the hill and the
combination weight of the towing vehicle and
trailer, the vehicle might start rolling backwards
slightly when you rst start up.
For hill starts with a trailer hitched:
●
Press and hold the brake pedal.
●
Press the button to disconnect the elec-
tronic parking brake ›››page226.
●
Automatic gearbox: Move the selector lever
to the D/S position.
●
Pull out the button and hold it in that posi-
tion to stop the towing vehicle and trailer with
the electronic parking brake.
●
Release the brake pedal.
●
Move o slowly.
●
Do not release the button until the engine
has suicient power to start driving.
WARNING
If a trailer is pulled incorrectly, this may lead
to loss of control of the vehicle and serious
injury.
●
Driving with a trailer and transporting
heavy or large objects will change the vehicle
handling and braking distances.
●
Always drive cautiously and carefully. Brake
earlier than usual.
●
Adapt your speed and driving style at all
times to suit visibility, weather, road and traf-
c conditions. Slow down, especially when
driving down hills or slopes.
●
Accelerate with particular care and cau-
tion. Avoid sudden braking and manoeuvres.
●
Take great care when overtaking. Reduce
speed immediately if you notice that the
trailer is swaying, however slightly.
●
Never attempt to “straighten” the towing
vehicle and trailer while accelerating.
●
Take into account the speed limit for vehi-
cles with a trailer, as it could be lower than for
vehicles without a trailer.
Stabilisation of the towing vehicle
and trailer combination
The stabilisation of the vehicle and trailer com-
bination is an additional function of the elec-
tronic stability control (ESC).
If the system detects that the trailer is weav-
ing, it intervenes to reduce the swaying of the
trailer.
Vehicle and trailer combination stabilisation
requirements
●
The vehicle is factory-equipped with a tow-
ing bracket or has been retro-tted with a
compatible towing bracket.
●
The ESC and TCS are active. The control
lamp or is not lit up on the instrument
cluster.
●
The trailer is connected to the towing vehicle
through the trailer power socket.
●
The vehicle is travelling at over 60km/h (ap-
prox. 37mph).
●
The maximum vertical load technically per-
missible is not being exceeded on the coupling
device.
Storing objects
329
Trailer mode
1)
Not available in all markets.
●
The trailer has a rigid draw bar.
●
If the trailer has brakes, it must be equipped
with a mechanical overrun brake.
WARNING
The enhanced safety provided by the elec-
tric stability control of the vehicle and trailer
should not lead you to take any risks that
could compromise your safety.
●
Adapt your speed and driving style at all
times to suit visibility, weather, road and traf-
c conditions.
●
Accelerate with caution when the road is
slippery.
●
When adjusting any settings, stop acceler-
ating.
WARNING
The electric stability control for the vehicle
and trailer may not correctly detect all driv-
ing conditions.
●
When the ESC is switched o, the stabilisa-
tion of the towing vehicle and trailer is also
switched o.
●
The stability system does not always detect
light trailers, so it may not stabilise these cor-
rectly.
●
When driving on surfaces with poor grip,
the trailer can even interfere with the stabil-
ity system.
●
Trailers with a high centre of gravity can tip
over without having previously weaved.
●
If a trailer is not attached, but a connec-
tor is plugged into the power socket (e.g. in-
stallation of a bicycle rack with lights), repea-
ted automatic braking may occur in extreme
driving conditions.
Electrically unlocking trailer hook
Fig.197 Left side of the luggage
compartment: button to unlock the tow
hitch.
The hook of the towing device is located in the
bumper and cannot be removed
1)
.
There should be no person, animal or object in
the path of the tow hook›››
.
Unlocking the tow hook and removing it
●
Stop the vehicle and apply the electronic
parking brake ›››page226.
●
Switch o the engine.
●
Open the rear lid.
●
Pull the ›››Fig.197 button briey. The
tow hook unlocks electrically and automati-
cally turns outwards. The button's control lamp
ashes.
●
Finish removing the tow hook by hand until
you feel and hear that it has engaged and the
control lamp on the button stays on.
●
Close the rear lid.
●
Hitching and connecting a trailer
›››page325.
Retracting the tow hook
●
Stop the vehicle and apply the electronic
parking brake.
●
Switch o the engine.
●
Unhook the trailer and disconnect the elec-
trical connection between it and the vehicle. If
you are using an adapter, remove it from the
trailer's power socket.
●
Open the rear lid.
●
Pull the ›››Fig.197 button briey. The tow
hook unlocks electrically.
330
Storing objects
●
Turn the tow hook under the bumper with
your hand until you feel and hear that it en-
gages and the control lamp on the button re-
mains on continuously.
●
Close the rear lid.
The button's control lamp
Flashing:
This means that the tow hook has not yet
engaged correctly or is damaged ››› .
Remains on:
If it remains on while the rear lid is open,
the tow hook is correctly in place both
when extracted and when covered.
The button's indicator lamp switches o ap-
proximately 1 minute after closing the rear lid.
WARNING
Improper use of the towing bracket may
cause injury and accidents.
●
Only use the tow hook if it is properly en-
gaged.
●
Always ensure that no person, animal or
object is to be found in the path of the tow
hook.
●
Never use a tool or instrument while the
tow hook is moving.
●
Never press the button ›››Fig.197 when
there is a trailer hooked to the vehicle or
when a carrier system or other accessories
are mounted on the tow hook.
●
If the tow hook is not attached properly, do
not use it. Instead, go to a specialised work-
shop and have the towing bracket checked.
●
If you detect any fault in the electrical sys-
tem or in the towing bracket, contact a speci-
alised workshop and ask them to check it.
●
If the ball has a diameter of less than
49mm at any one point, do not use the tow-
ing bracket under any circumstances.
NOTICE
If you clean the vehicle with high-pressure
or steam devices, do not point the jet di-
rectly towards the retractable tow hook or
the trailer power socket, as this may damage
the joints or remove the grease necessary for
lubrication.
Note
At extremely low temperatures, the tow hook
may be impossible to operate. In this case,
place the vehicle in a warmer location (for
example, a garage).
Installing a rear carrier system or a
bicycle rack on the trailer hitch
Fig.198 Recommended weight distribution
on the rear support system.
Examples of rear carrier systems are bicycle
racks or multi-purpose boxes that are installed
on the trailer hitch.
Only use rear carrier systems that have been
specied by the respective manufacturer for
the vehicle model, model year and version of
the vehicle in question ›››
.
CUPRA recommends the use of genuine
CUPRA spare parts and accessories, which can
be purchased from the brand’s dealers. Install
the rear carrier system according to the manu-
facturer’s installation instructions.
The load capacity results from the weight of
the rear carrier system and the weight of the
load carried on it.
Storing objects
331
Trailer mode
A
B
The recommended maximum load capacity of
the rear carrier system installed on the trailer
hitch may be dierent from the maximum ver-
tical load on the specic vehicle coupling.
However, it is not permitted to exceed the
maximum permitted vertical load on the tow
hitch (which depends on the model).
The load capacity is reduced due to the lever
eect that occurs the further the carrier sys-
tem is from the ball head.
Place heavy objects as close as possible to the
trailer hitch ›››
Fig.198.
Maximum load capacity depending on the
vehicle
To nd out the recommended load capacity
for your vehicle, check the maximum vertical
load on its coupling ›››page411. Please refer
to the following table for the load capacity.
In accordance with the UN-R-55 guideline,
CUPRA recommends not carrying more bicy-
cles than recommended on the rear rack sys-
tem.
Maximum verti-
cal load on the
vehicle's specic
coupling
Maximum
load ca-
pacity
Number
of bicy-
cles
50 kg 50 kg 2
55 kg 55 kg 2
From 75 kg 75 kg 3
Maximum load overhang of the rear carrier
system
Fig.199 Schematic representation of the
maximum load overhang of a bicycle rack for
two or three bicycles.
With up to 55kg load capacity: 500mm
(approx. 19.7in)
With 75kg load capacity: 700mm (approx.
27.6in)
The maximum overhang shall not exceed
500mm from the centre of the ball head to
the to the centre of the rail of the last support
›››
Fig.199
A
for two-bicycle racks. In the
case of three-bicycle racks, the overhang must
not exceed 700mm ›››
Fig.199
B
.
WARNING
The incorrect use of a rear carrier system in-
stalled on the tow hook can cause accidents
and injury.
●
Make sure that the carrier system is suita-
ble for your vehicle.
●
Read and observe the installation instruc-
tions of the rear carrier system manufac-
turer.
●
Never attach a rear carrier system below
the ball head of the trailer hitch. The system
could slip due to the shape of the hitch.
Note
Before setting o, CUPRA recommends re-
moving, to the extent possible, all accesso-
ries from the load attached to the carrier
system. Examples of these accessories are
baskets and panniers, child seats or batteries.
This improves the aerodynamics and centre
of gravity of the rear carrier system.
332
Storing objects
Retrotting a towing bracket
Fig.200 Towing device: dimensions and
attachment points.
Fig.201 Towing device: dimensions and
attachment points.
Distance measurements (measurements can
vary depending on the dierent chassis combi-
nations):
A
Mounting points on the vehicle
B
65 mm (minimum)
C
350mm to 420mm (fully laden vehicle)
D
361 mm
E
581 mm
F
1059 mm
G
991 mm
CUPRA recommends that towing brackets be
retrotted at a specialised workshop. For ex-
ample, it may very well be necessary to adjust
the cooling system or mount thermal protec-
tion plates. To do so, CUPRA recommends go-
ing to a specialised CUPRA dealer or any SEAT
dealership.
If a towing bracket is retrotted, the distance
specications should always be kept in mind.
The distance between the centre of the ball
head and the road ›››
Fig.200
C
must never
be less than that indicated. This also applies
when the vehicle is fully loaded, including the
technically permissible maximum vertical load
on the coupling device.
WARNING
If the cables are improperly or incorrectly
connected, this may lead to malfunctions in
the entire vehicle electronic system, as well
as to accidents and serious injuries.
●
Never connect the trailer's electric sys-
tem to the electrical connections of the tail
lights or any other unsuitable power sources.
Only use suitable connectors to connect the
trailer.
●
The towing bracket should be retrotted
only at a specialised workshop.
WARNING
If the towing bracket is badly tted or unsuit-
able, the trailer may separate from the vehi-
cle while driving. This could cause serious ac-
cidents and fatal injuries.
Note
●
According to regulation EU2021_535 it is
not permitted to install a towing device that
cannot be removed or retracted.
●
Only use towing brackets that have been
approved by CUPRA for the model in ques-
tion.
●
In some versions, the tting of a conven-
tional towing hook solution is not recom-
mended. Please consult your Technical Serv-
ice.

Related Topics

Popular Owner Manuals