Get Access Guide for DS 9 4 Door First Generation (2020-2024)

24

Access

02

– Back-up Unlocking/Locking of the doors.

Selective unlocking

Electronic key with remote

control function and

built-in key,

Driver’s door and fuel filler/charging flap

►ꢀ Press the unlocking button.

►ꢀ Press it again to unlock the other doors and

the boot.

The charging nozzle can be unplugged on the

second press.

Remote control function

Complete or selective unlocking, and alarm

deactivation (depending on version), is confirmed

by the flashing of the direction indicators.

Depending on version, the door mirrors unfold.

Opening the windows

Depending on version, holding the

unlocking button pressed for more than 3

seconds opens the windows.

►ꢀ To eject the key or put it back in place, pull and

hold the button.

Depending on version, the remote control can be

used to perform the following remote functions:

– Unlocking/Locking/Deadlocking the vehicle.

– Unlocking - Opening the boot.

Once the built-in key is ejected, always

keep it with you to be able to carry out the

corresponding back-up procedures.

The windows stop when the button is released.

Selective unlocking and opening of the

boot

– Folding/Unfolding the door mirrors.

– Folding/Unfolding the exterior door handles.

– Activating/Deactivating the alarm.

– Locating the vehicle.

By default, selective unlocking of the boot is

deactivated and its motorised operation is

activated.

Unlocking the vehicle

►ꢀ Press and hold this button to unlock

the boot and activate its motorised

opening.

– Opening/Closing the windows.

Selective unlocking (driver’s door, boot) is

configured in the Driving/Vehicle touch

screen menu.

– Closing the sunroof.

– Activating the vehicle’s electronic immobiliser.

The doors and fuel filler flap remain locked.

Built-in key

Complete unlocking

If selective unlocking of the boot is

deactivated, pressing the button unlocks

the whole vehicle.

The key built into the remote control can be

used for the following operations, depending on

version:

►ꢀ Press the unlocking button.

The vehicle's door handles, and depending on

version, the door mirrors, unfold.

– Activation/Deactivation of the front passenger

airbag.

25

Access

02

If motorised operation of the boot is

Deadlocking

Locating the vehicle

Helps you to locate your vehicle from a distance,

deactivated, pressing the button releases

Deadlocking renders the interior door

the boot.

with the vehicle locked:

controls inoperative. It also disables the

central locking button.

To lock the vehicle, it is necessary to close the

boot again.

– The direction indicators flash for approximately

10 seconds.

The horn remains operational.

Never leave anyone inside the vehicle when it

is deadlocked.

– The door mirror spotlamps come on.

– The courtesy lamps come on.

►ꢀ Press this button.

Locking the vehicle

►ꢀ Press the locking button again within 3

seconds to deadlock the vehicle (confirmed by the

temporary lighting of the direction indicators).

Closing the windows and sunroof

Advice

Normal locking

Remote control

►ꢀ Press the locking button.

An audible signal sounds before the start of the

movement.

The remote control is a sensitive, high-

frequency device; avoid handling it in your

pocket, due to the risk of unintentionally

unlocking the vehicle.

The locking, and the activation of the alarm

depending on version, is confirmed by the lighting

of the direction indicators.

Maintaining pressure on the locking

button for more than 3 seconds allows the

windows and, depending on version, the sunroof

to be closed to the desired position.

The vehicle's handles retract and, depending on

version, the door mirrors fold.

Avoid pressing the remote control buttons

while out of range of the vehicle, due to

the risk of rendering the remote control

inoperative. It would then be necessary to

reset it.

This operation also closes the sunroof blind.

An access (door or boot) that is not

properly closed prevents locking of the

Ensure that no person or object could

prevent the correct closing of the

windows and sunroof.

vehicle. However, if the vehicle is fitted with an

alarm, it will be activated after 45 seconds.

If the vehicle is unlocked but the doors or boot

are not subsequently opened, the vehicle will

automatically lock itself again after about

30 seconds. If the vehicle is fitted with an

alarm, it will be reactivated automatically.

If, on versions with alarm, you want to leave

the windows and/or sunroof partially open, you

must first deactivate the interior volumetric

alarm protection.

Anti-theft protection

Do not modify the electronic vehicle

immobiliser, as this might result in

malfunctions.

For more information on the Alarm, refer to the

corresponding section.

Locking the vehicle

Driving with the doors locked could make

it more difficult for the emergency services

26

Access

02

to enter the passenger compartment in an

Unlocking the vehicle

emergency.

As a safety precaution, take the electronic key

with you when leaving the vehicle, even for a

short time.

Purchasing a second-hand vehicle

Have the key codes memorised by

a dealer, to ensure that the keys in your

possession are the only ones able to start the

vehicle.

Zone A: welcome lighting on approaching the

vehicle (between 3 and 5 metres from the

vehicle).

Selective unlocking (driver’s door, boot) is

configured in the Driving/Vehicle touch

screen menu.

Proximity Keyless Entry

and Start

This is a Keyless Entry and Start system.

It enables automatic vehicle locking/unlocking

simply by detecting the electronic key.

As long as the driver has the electronic key on

their person, the vehicle unlocks as they approach

and locks when they walk away.

Zone B: automatic locking on moving away from

the vehicle (about 2 metres from the vehicle).

Zone C: automatic unlocking on approaching the

vehicle (between 1 and 2 metres from the vehicle).

The automatic functions are configured

via the Driving/Vehicle touch screen menu.

With the electronic key on their person, the driver

can also lock and unlock their vehicle by pressing

on the flush-fitting door handles.

Selective unlocking is deactivated by default.

Complete unlocking

The vehicle (doors and boot) unlocks:

►ꢀ either automatically when the driver is

approaching (zone C), if the automatic functions

are activated;

►ꢀ or by a light press on a handle.

Key recognition zones:

For more information on the Flush-fitting door

handles, refer to the corresponding section.

The unlocking, and the deactivation of the alarm

depending on version, is confirmed by flashing of

the direction indicators.

The vehicle door handles, and depending on

version, the door mirrors, unfold.

If the key remains around the vehicle

(zones A, B or C) for more than 15 minutes

without action, the automatic functions are

deactivated. To unlock or lock the vehicle, use

27

Access

02

the remote control or press on one of the door

handles.

Deadlocking

Locking the vehicle

Deadlocking renders the interior door

If using the door handle does not lock/unlock

the vehicle, bring the key closer and repeat the

desired action.

Normal locking

controls inoperative. It also deactivates

the central locking button.

The horn remains operational.

Never leave anyone inside the vehicle when it

is deadlocked.

Selective unlocking

Driver’s door and fuel filler/charging flap

They unlock:

►ꢀ either automatically when approaching the

driver’s door, if the automatic functions are

activated;

►ꢀ or by a light press on the handle.

The driver's door handle unfolds.

►ꢀ Once inside the vehicle, to unlock all accesses,

press the central locking button or pull the

opening control of any door.

With the doors and boot closed, the vehicle locks:

►ꢀ either automatically when leaving recognition

zone B, if the automatic functions are activated;

►ꢀ or by a light press on a door handle or on the

control located on the tailgate;

►ꢀ Gently press one of the door handles or the

control located on the tailgate to lock the vehicle.

►ꢀ Press it again within 3 seconds to deadlock

the vehicle (confirmed by the temporary lighting

of the direction indicators).

Selective unlocking of the boot

The boot unlocks automatically as you approach

the rear of the vehicle.

The locking is confirmed by the illumination of the

direction indicators as well as an audible signal

for the locking on moving away from the vehicle.

It is not possible to lock the vehicle if the

electronic key is left inside.

►ꢀ Press the tailgate control to open the boot.

The doors remain locked.

If the vehicle is unlocked with the handles

retracted, a first press on any handle

unfolds all the handles. The vehicle remains

unlocked.

If the vehicle is unlocked with the handles

retracted, a first press on any handle

unfolds all the handles. The vehicle remains

unlocked.

Press one of the handles again to lock it.

If one of the doors or the boot is still open

or if the electronic key for the Keyless

Press one of the handles again to lock it.

28

Access

02

Entry and Startsystem has been left inside the

– If the welcome lighting is triggered

several times in succession without the

vehicle subsequently being started, it will be

deactivated.

Manual

►ꢀ Press this button to lock/unlock the vehicle

(doors and boot) from inside the passenger

compartment.

vehicle, central locking will not take place.

If the vehicle is unlocked but the doors or

boot are not subsequently opened, the

vehicle will automatically lock itself again

after about 30 seconds. If the vehicle is fitted

with an alarm, it will be reactivated

automatically.

– All "hands-free" functions switch to

hibernation mode after 21 days without being

used. To restore these functions, unlock the

vehicle using the remote control and start the

engine.

The indicator lamp comes on to confirm the

central locking of the vehicle.

Central locking does not take place if any

of the doors are open.

To unfold the exterior handles, press the

button once when the vehicle is locked or

twice when it is unlocked.

Electrical interference

The automatic door mirror folding/

unfolding function is configured via the

touch screen’s Driving/Vehicle menu.

The electronic key may not work if it

is close to an electronic device (e.g. mobile

telephone (switched on or on standby), laptop

computer, strong magnetic fields). If this

occurs, move the electronic key away from the

electronic device.

When locking/deadlocking from the

outside

As a safety measure, never leave the

vehicle, even for a short time, without

taking the Keyless Entry and Start system’s

electronic key with you.

When the vehicle is locked or deadlocked from

the outside, the indicator lamp flashes and the

button is deactivated.

Be aware of the risk of theft of the vehicle if

the key is present in one of the defined areas

while the vehicle is unlocked.

►ꢀ After normal locking, pull one of the interior

door controls to unlock the vehicle.

►ꢀ After deadlocking, you must use the remote

control, the "Keyless Entry and Start" system

or the built-in key to unlock the vehicle.

Central locking

In order to preserve the battery in the

electronic key and the vehicle's battery:

– The unlocking on approach function (zone C)

automatically switches to hibernation mode

after several days (approximately one week)

without being used. To unlock the vehicle, use

the remote control or press on one of the door

handles. The next time the vehicle is started,

the automatic unlocking and locking functions

will be reactivated.

Automatic (anti-intrusion

security)

The doors and boot lock automatically while

driving (speed above 6 mph (10 km/h)).

To deactivate/reactivate this function (activated

by default):

29

Access

02

►ꢀ Press the button until an audible signal is

triggered and a confirmation message appears.

In the first case, change the remote control

battery.

In the event of a malfunction of the

central locking system, the battery must

be disconnected to ensure that the vehicle is

locked fully.

In the second case, reinitialise the remote control.

Refer to the corresponding sections.

Transporting long or voluminous objects

Press the central locking control to drive

with the boot open and the doors locked.

Otherwise, every time the speed of the vehicle

exceeds 6 mph (10 km/h), the sound of the

locks rebounding will be heard and an alert will

be displayed.

Driver's door

►ꢀ If the handle is retracted, press on it up to the

point of resistance to unfold it.

►ꢀ Pull the handle to access the lock.

►ꢀ Insert the key in the lock and turn it to lock

the door.

Back-up procedures

Passenger doors

►ꢀ Press the driver's door handle until the point

of resistance to unfold it then pull it to access the

lock.

Unlocking

Lost keys, remote control,

electronic key

Go to a dealer with the vehicle’s registration

certificate and your personal identification

documents.

►ꢀ Pull the interior door opening control.

►ꢀ Insert the key in the door lock.

►ꢀ Slightly release the driver’s door handle.

►ꢀ Turn the key towards the front/rear to unlock/

lock the vehicle.

Locking

The dealer will be able to retrieve the key code

and the transponder code, enabling a new key to

be ordered.

If the vehicle is fitted with an alarm, it will

not be activated when locking with the

key.

Complete unlocking/locking of

the vehicle with the key

Use this procedure in the following situations:

– Remote control battery discharged.

– Remote control malfunction.

If the alarm is activated, the siren sounds

when the door is opened; switch on the ignition

to stop it.

Central locking not functioning

Use these procedures in the following cases:

– Vehicle battery discharged.

►ꢀ Open the doors.

►ꢀ For the rear doors, check that the child lock is

not on.

– Vehicle in an area subject to strong

electromagnetic interference.

– Central locking malfunction.

– Battery disconnected or discharged.

30

Access

02

Refer to the corresponding section.

►ꢀ Remove the black cap, located on the edge of

the door, using the key.

►ꢀ Reinitialise the remote control.

For more information on Reinitialising the remote

control, refer to the corresponding section.

where the pressure is extremely low due to

very high altitude.

Do not try to burn, crush or cut a used battery.

►ꢀ Insert the key into the socket without forcing

it, then turn the latch towards the inside of the

door.

Do not throw remote control batteries

away, as they contain metals that are

harmful to the environment. Take them to an

approved disposal point.

Reinitialising the remote

control

Following replacement of the battery or in the

event of a fault, it may be necessary to reinitialise

the remote control.

►ꢀ Remove the key and refit the black cap.

►ꢀ Close the doors and check from the outside

that the vehicle is locked.

This equipment contains a button type

battery.

Changing the battery

A message is displayed on the instrument panel

Do not swallow the battery. Risk of chemical

burns!

when the battery needs changing.

Swallowing the battery can cause serious

internal burning in only 2 hours and can be

fatal.

Battery type: CR2032/3 volts.

If batteries have been swallowed or inserted

into a part of the body, seek immediate

medical advice.

Keep new and used batteries out of the reach

of children.

►ꢀ Press the handle until the point of resistance

to unfold it and access the lock.

If the battery compartment does not close

properly, stop using the product and keep it out

of the reach of children.

►ꢀ Insert the mechanical key (incorporated into

the remote control) into the lock to open the

vehicle.

Risk of explosion if the battery is replaced

with an incorrect type!

►ꢀ Place the electronic key against the back-up

reader on the steering column and hold it there

until the ignition is switched on.

►ꢀ Unclip the cover by inserting a small

screwdriver in the slot and lift the cover.

►ꢀ Remove the flat battery from its housing.

►ꢀ Put the new battery in place, respecting the

polarity. Start by inserting it into the contacts

located in the corner, then clip the cover onto the

unit.

Replace the battery with the same type.

►ꢀ While in mode P of the automatic gearbox,

depress the brake pedal.

Risk of explosion or leaking of

inflammable liquid or gas!

►ꢀ Switch on the ignition by pressing the "START/

STOP" button.

Do not use in/store in/place in an environment

where the temperature is extremely high or

31

Access

02

If the fault persists after reinitialisation, contact

a dealer or a qualified workshop without delay.

For more information on Proximity Keyless Entry

and Start, refer to the corresponding section.

When selective unlocking is activated,

only the driver door's handle will unfold

and only the driver's door can be opened.

In the event of a battery failure or system

malfunction, manually unfold the driver’s

handle by pressing on it up to the point of

resistance. Then pull the handle to access the

lock and follow the back-up procedures.

For more information on the Back-up

Doors

From inside

►ꢀ Pull the interior door opening lever; the exterior

door handles unfold automatically.

Opening one of the doors from inside unlocks the

rest of the vehicle.

Flush-fitting door handles

The doors are equipped with handles that unfold

and retract automatically depending on the

vehicle state:

procedures, refer to the corresponding section.

– When unlocking the vehicle, the handles unfold

to allow access to the vehicle.

With selective unlocking activated:

– Opening the driver's door unlocks the

driver's door only (if the vehicle has not already

been completely unlocked).

Too frequent presses on the handle up to

the point of resistance may damage its

mechanism.

– When the vehicle is locked, the handles retract.

– Opening one of the passenger doors unlocks

the rest of the vehicle.

In case of frost, press the handle to

release it.

– Opening a door from inside causes the

unfolding of all the exterior handles.

From inside the vehicle, it is possible to unfold the

handles:

– by opening a door.

Boot

– by pressing the central locking button once

when the vehicle is locked or twice when

unlocked.

A. Retracted position

B. Unfolded position

Opening

When driving, the handles automatically retract

once the vehicle speed exceeds 3 mph (5 km/h).

►ꢀ It is possible to manually unfold the handles at

any time by pressing on them.

Opening

Once unfolded, the handles retract automatically

after 3 minutes without the vehicle being locked.

Depending on version, pressing on the handles

also locks/unlocks the vehicle, if the electronic

key is detected.

From outside

►ꢀ Unlock your vehicle to unfold the door handles.

►ꢀ Pull the handle.

32

Access

02

►ꢀ After unlocking the vehicle or just the boot,

press the opening control and then lift the

tailgate.

Closing

►ꢀ Lower the tailgate using one of the interior

grab handles.

►ꢀ Release the handles and press down on the

outside of the boot to close it.

►ꢀ Insert a small screwdriver into hole A of the

lock to unlock the boot.

In the event of a malfunction or if you

experience difficulty opening or closing

the boot, have it checked by a dealer or a

qualified workshop without delay, to avoid the

issue deteriorating and prevent any risk of the

boot dropping, potentially causing serious

injury.

Never introduce a finger in the locking

system of the motorised boot - risk of

►ꢀ Move the latch to the left.

Locking after closing

serious injury!

If the fault persists after closing again, the boot

will remain locked.

Anti-pinch

In the event of a fault with the central

locking system, it is essential to

The motorised boot has an obstacle detection

system that automatically interrupts and reverses

its movement by a few degrees to allow the

obstacle to be cleared.

disconnect the battery to lock the boot and so

ensure complete locking of the vehicle.

Back-up release

To manually unlock the boot in the event of a

Please note that this anti-pinch system is not

active at the end of the closing travel (around 1

cm from completely closed).

battery or central locking failure.

Motorised tailgate

The motorised boot must only be operated with

Unlocking

To avoid the risk of injury through

pinching or trapping, before and during

manoeuvres of the motorised boot:

– ensure that there is no-one close to the rear

of the vehicle;

►ꢀ Fold the rear seats to gain access to the lock

from inside the boot.

the vehicle stationary.

Check that there is enough space to allow

for the movement of the motorised boot.

– monitor the activity of your passengers,

particularly any children.

33

Access

02

Bicycle carrier / Towing device

Following the interruption of a movement,

B. Using the exterior boot control.

C. Using the interior boot control.

D. Using the control on the dashboard*.

pressing one of these controls again reverses

the movement.

The motorised boot is not designed to support a

bicycle carrier.

When installing a bicycle carrier on the towing

device with connection of the cable to the towing

socket, the motorised operation of the boot will

be automatically deactivated.

Manual operation

Opening/Closing

The boot can be manoeuvred by hand, even with

motorised operation activated.

There must be no motorised manoeuvre in

progress.

►ꢀ Press and hold the central button A of the

electronic key.

If using a towing device or bicycle carrier not

approved by the Manufacturer, it is essential to

deactivate the motorised operation of the boot.

or

►ꢀ Briefly press the exterior boot control B, with

the electronic key on your person.

During manual opening and closing of the

motorised boot, boot struts are not used.

Resistance to opening and closing is therefore

quite normal.

or

Motorised operation

Motorised operation of the boot is set via

the Driving/Vehicle touch screen menu.

This function is activated by default.

►ꢀ Briefly press the interior boot control C

(locking only).

or

Repeatedly opening and closing the

motorised boot can cause overheating of

its electric motor, after which opening and

closing will not be possible.

►ꢀ Press twice in succession on control D on the

dashboard (opening only).

If motorised operation is not activated,

these actions release the boot (partially-

open position).

Allow at least 10 minutes for the electric motor

to cool down before operating the boot again.

If you are unable to wait, operate it manually.

When the vehicle is locked, the request to open

the boot with one of the controls A or B unlocks

the vehicle, or only the boot if selective

unlocking is activated, prior to the opening of

the boot.

Manual closing of the

motorised boot in case of

failure

It is possible to interrupt the operation of

the boot at any point.

This operation is only necessary in the case of

There are several ways of operating the boot:

A. Using the Keyless Entry and Start system

electronic key.

failure of the boot motor.

Pressing one of these controls again interrupts

the movement that is underway.

* Depending on version.

34

Access

02

If the failure originates from the battery, it is

recommended to recharge it or change it with the

boot closed.

Hands-free function

("Hands-Free Tailgate

Access")

In this situation, a significant force may be

needed to close the boot.

(Depending on version)

►ꢀ Close it gently without slamming, as slowly as

possible, by pushing at the centre of the boot.

With the electronic key on your person, this

function allows the motorised tailgate to be

opened, closed or stopped via a "kicking"

movement under the rear bumper.

The function is set via the Driving/Vehicle

touch screen menu.

Do not lower the boot by pushing at one of

its sides - risk of damage!

Precautions in use

This function is activated by default.

To avoid unwanted opening of the boot

when using the towing device:

Ensure that you are steady on your feet

before performing the "kicking"

movement.

– deactivate the “Hands-Free Tailgate

Access” function in advance in the vehicle

configuration menu;

Take care not to touch the exhaust system

which may be hot - risk of burns!

– or move the electronic key away from the

recognition zone, with the boot closed.

►ꢀ Position yourself behind the vehicle by the

number plate and do a “kicking” movement in the

"OK" detection zone.

Rechargeable hybrid vehicles

The function is not available when the

vehicle is connected.

In wintry conditions

To avoid any operating problems, remove

the snow or wait until the ice melts before

requesting motorised opening of the boot.

The “kicking” movement must be given forwards,

fluidly, not too fast, in a vertical gesture from the

bottom up. Raise the foot sufficiently and remove

it immediately.

When washing

Recognition of the "kicking" movement is

confirmed by the lighting of the direction

indicators followed by an audible signal.

When washing the vehicle in an automatic

car wash, do not forget to lock the vehicle to

prevent any risk of unwanted opening.

"Sideward kicking" movements do not

work. If the “kicking” movement has not

35

Access

02

been detected, wait at least 2 seconds before

repeating the movement.

– washing the vehicle;

The alarm is triggered if anyone breaks a window,

– maintenance is performed on the vehicle;

– accessing the spare wheel.

enters the passenger compartment or moves

inside the vehicle.

Do not give repetitive kicks.

To avoid such operating problems, keep the

electronic key away from the recognition zone or

deactivate the hands-free function.

Anti-tilt monitoring

If the boot has not started to move, check that:

– the function is activated.

The system checks for any change in the attitude

of the vehicle.

– the electronic key is on your person, outside the

vehicle in the rear recognition area.

– the "kicking" movement was performed in the

detection zone, close enough to the bumper.

– the foot was removed from the bumper quickly

enough.

Towing device

The alarm goes off if the vehicle is lifted or moved.

The installation of a towing device may

disturb the detection system.

When the vehicle is parked, the alarm will

not be triggered if the vehicle is knocked.

Self-protection function

Alarm

(Depending on version)

The system checks whether any of its

components are out of service.

Recommendations on the

hands-free function (Hands-

Free Tailgate Access)

If it does not work, check that the electronic key

is not exposed to a source of electromagnetic

interference (e.g. smartphone).

The function may be deactivated or affected if

there is rain or snow.

The alarm is triggered if the battery, the central

control or the siren wiring is put out of service or

damaged.

Work on the alarm system

Contact a dealer or a qualified workshop.

Locking the vehicle with full

alarm system

The function may not work correctly with a

prosthetic leg.

System which protects and provides a deterrent

against theft and break-ins.

In some circumstances, the boot may open or

close by itself, particularly when:

– hitching up or removing a trailer;

– fitting or removing a bicycle carrier;

– loading or unloading bicycles on/from a bicycle

carrier;

Activation

Exterior perimeter monitoring

►ꢀ Switch off the ignition and exit the vehicle.

►ꢀ Lock or deadlock the vehicle using the remote

control or by pressing on one of the front door

handles.

The system checks for opening of the vehicle.

The alarm is triggered if anyone tries to open a

door, the boot or the bonnet, for example.

– depositing or lifting something behind the

vehicle;

Interior volumetric monitoring

When the monitoring system is active, the red

indicator lamp in the button flashes once per

The system checks for any variation in volume in

the passenger compartment.

– an animal approaches the rear bumper;

36

Access

02

second and the direction indicators come on for

about 2 seconds.

opened within 30 seconds of unlocking), the

monitoring system is automatically activated.

Reactivating the interior volumetric and

anti-tilt monitoring

The exterior perimeter monitoring is activated

after 5 seconds and the interior volumetric and

anti-tilt monitoring after 45 seconds.

►ꢀ Deactivate the exterior perimeter monitoring

by unlocking the vehicle using the remote control

or by pressing on a door handle.

Locking the vehicle with

exterior perimeter monitoring

only

Deactivate the interior volumetric and anti-tilt

monitoring to avoid the unwanted triggering of

the alarm, in certain cases such as:

– Slightly open window.

The indicator lamp in the button goes off.

►ꢀ Reactivate all monitoring by locking the

vehicle using the remote control or by pressing on

a door handle.

The alarm does not activate when locking

automatically from a distance.

If an opening (door, boot or bonnet) is not

properly closed, the vehicle is not locked,

but the exterior perimeter monitoring will be

activated after 45 seconds, at the same time

as the interior volumetric and anti-tilt

monitoring.

The red indicator lamp in the button once again

flashes every second.

– Washing the vehicle.

Triggering of the alarm

This is indicated by sounding of the siren and

flashing of the direction indicators for 30

seconds.

– Changing a wheel.

– Towing the vehicle.

– Transport on a ship or ferry.

Deactivation

Deactivating the interior volumetric and

anti-tilt monitoring

Depending on the country of sale, certain

monitoring functions remain active until

the alarm has been triggered eleven times

consecutively.

►ꢀ Press one of the remote control unlocking

buttons:

►ꢀ Switch off the ignition and within 10 seconds

press the alarm button until its red indicator lamp

is on fixed.

Short press.

When the vehicle is unlocked using the remote

control or the Keyless Entry and Start system,

rapid flashing of the red indicator lamp in the

button informs you that the alarm was triggered

during your absence. When the ignition is

switched on, this flashing stops.

Long press.

►ꢀ Get out of the vehicle.

►ꢀ Immediately lock the vehicle using the remote

control or by pressing one of the front door

handles.

or

►ꢀ Unlock the vehicle using the remote control or

by pressing one of the front door handles.

The monitoring system is deactivated: the

indicator lamp in the button goes off and the

direction indicators flash for about 2 seconds.

Only the exterior perimeter monitoring is

activated; the button's red indicator lamp flashes

once every second.

Failure of the remote control

To deactivate the monitoring functions:

►ꢀ Unlock the vehicle using the key in the driver's

door lock.

To take effect, this deactivation must be

carried out after each time the ignition is

switched off.

After unlocking using the remote control

If the vehicle automatically locks itself

►ꢀ Open the door; the alarm is triggered.

again (as happens if a door or the boot is not

37

Access

02

►ꢀ Switch on the ignition; this stops the alarm.

The indicator lamp in the button goes off.

opens/closes completely when the switch is

released.

Electric windows

Operating the switch again stops the movement

of the window.

Locking the vehicle without

activating the alarm

►ꢀ Lock or deadlock the vehicle using the key

(built-in the remote control) in the driver's door

lock.

Window controls remain operational for

approximately 45 seconds after switching

off the ignition or after locking the vehicle.

After that time, the controls are disabled.

To reactivate them, switch on the ignition or

unlock the vehicle.

Automatic activation

(Depending on version)

1. Left-hand front

Anti-pinch

2. Right-hand front

The system is activated automatically 2 minutes

after the last door or the boot is closed.

►ꢀ To avoid triggering the alarm on entering the

vehicle, first press the unlocking button on the

remote control or unlock the vehicle using the

"Keyless Entry and Start" system.

3. Left-hand rear

If the window meets an obstacle while rising, it

stops and immediately partially lowers again.

4. Right-hand rear

5. Deactivation of electric window controls

located by rear seats

Deactivation of the rear

controls for the rear electric

windows

Deactivation of the rear door opening controls

(electric child lock)*

Malfunction

For children's safety, press switch 5 to

deactivate the rear electric windows

controls.

When the ignition is switched on, the fixed

lighting of the red indicator lamp in the button

indicates a system malfunction.

Have it checked by a dealer or a qualified

workshop.

Manual operation

►ꢀ To open/close the window, press/pull the

switch without passing the point of resistance;

the window stops as soon as the switch is

released.

The indicator lamp for the button comes on,

accompanied by a message confirming activation.

With the ignition on, it remains lit, as long as the

child lock remains activated.

Automatic operation

►ꢀ To open/close the window, press/pull the

Use of the rear electric windows from the driver's

controls remains possible.

switch past its resistance point: the window

* Depending on version.

38

Access

02

For versions fitted with an electric child

lock, this control also deactivates the

Pay particular attention to children when

operating the windows.

B. Sunroof blind control

The sunroof or blind can be operated when the

ignition is turned on (if the battery has enough

charge), with the engine running, in STOP mode of

Stop & Start, and up to 45 seconds after turning

off the ignition or after locking the vehicle.

interior rear door controls.

Be aware of passengers and/or other persons

present when closing windows remotely using

the electronic key.

For more information on the Child lock, refer to

the corresponding section.

Do not put your head or arms through the open

windows when the vehicle is moving - risk of

serious injury!

Reinitialising the electric

windows

After reconnecting the battery, or in the event

of abnormal window movement, the anti-pinch

function must be reinitialised.

Precautions

Do not put your head or arms through the

sunroof while the vehicle is moving - risk

of serious injury!

Sunroof

The sunroof consists of a movable glass panel

that slides over the roof and a blind that can

be opened independently. Opening the sunroof

automatically opens the blind.

The anti-pinch function is disabled during the

following sequence of operations.

For each window:

Ensure that any luggage or accessories

carried on the roof bars do not interfere

with the movement of the sunroof.

Do not place heavy loads on the movable glass

panel of the sunroof.

►ꢀ Lower the window fully, then raise it; it will

rise in steps of a few centimetres each time the

control is pressed. Repeat the operation until the

window is fully closed.

►ꢀ To operate the panoramic sunroof or the blind,

use the buttons in the roof console.

►ꢀ Continue to pull the control for at least one

second after the window reaches the closed

position.

If the sunroof is wet, following a rain

shower or washing the vehicle, wait until

it is completely dry before operating it.

Do not operate the sunroof if it is covered by

snow or ice - risk of damage!

If an electric window meets an obstacle

during operation, the movement of the

window must be reversed. To do this, press the

relevant control.

Use only plastic scrapers to remove snow or

ice from the sunroof.

When the driver operates the passengers’

electric window controls, it is important to

ensure that nothing can prevent the window

from closing properly.

It is important to ensure that passengers use

the electric windows correctly.

A. Sunroof control

39

Access

02

Regularly check the condition of the

Anti-pinch system

locking control. The manoeuvre stops as soon

sunroof seals (e.g. presence of dust, dead

as the locking control is released.

If the sunroof or blind encounters an obstacle

when closing, the movement is automatically

reversed.

leaves).

If using a car wash, check first that the roof is

correctly closed and keep the high-pressure jet

at least 30 centimetres from the seals.

Closing of the blind is limited by the

position of the sunroof: the blind cannot

go further than the front of the movable glass.

During simultaneous movements of the

sunroof and blind, the blind automatically

stops or resumes movement depending on the

position of the sunroof.

The roof anti-pinch system is designed to be

effective at speeds of up to 75 mph (120 km/h).

Opening/Closing

Never leave the vehicle with the sunroof

open.

►ꢀ To open the sunroof or the blind, use the part

of the button located towards the rear of the

vehicle.

Operation

►ꢀ To close the sunroof or the blind, use the part

of the button located towards the front of the

vehicle.

Reinitialisation

Following reconnection of the battery or in the

event of a fault or jerky movement of the sunroof

or blind, reinitialisation is required.

When opening the sunroof fully, the movable

glass moves to a partially open position, then

slides over the roof. Any intermediate position is

possible.

Operation of buttons

►ꢀ Pressing a button beyond its point of

resistance directly opens or closes the sunroof or

blind fully.

►ꢀ Check that nothing is interfering with the

sunroof or blind and that the seals are clean.

►ꢀ With the ignition on, fully close the sunroof

and blind.

Depending on the speed of the vehicle, the

partially open position may vary to

improve the acoustics.

►ꢀ Pressing the button again stops the current

movement.

►ꢀ Press and hold the front part of button A, until

the sunroof and blind move slightly, then hold for

a further 1 second before releasing.

►ꢀ When holding a button (without going

beyond the point of resistance), the movement

of the sunroof or blind stops when this button is

released.

Before operating the sunroof or blind

control buttons, ensure that no object or

person might prevent the movement.

Be particularly aware of children when

operating the sunroof or blind.

►ꢀ Wait 2 seconds and then press and hold the

front part of button A. The blind and the sunroof

will open and close, one after the other. When

both are completely closed again, hold for a

further 2 seconds and release.

►ꢀ When the sunroof is closed: pressing once

without passing the point of resistance moves it

to a partially open position.

If something is trapped when operating

the sunroof or blind, you should reverse the

movement of the sunroof or blind by pressing

the control in question.

►ꢀ When the sunroof is partially open: pressing

once without passing the point of resistance

opens or closes it fully.

If there is an operating fault, restart the

whole procedure.

The driver must ensure that passengers use

the sunroof and blind correctly.

The sunroof and windows, then the blind,

can be closed by holding down the door

Access for Your DS 9 4 Door First Generation (2020-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals