Get In the event of a breakdown -> Spare wheel Guide for DS 9 4 Door First Generation (2020-2024)

164

In the event of a breakdown

►ꢀ Start the compressor by placing the switch

at position "I" and adjust the pressure to the

value shown on the vehicle's tyre pressure label.

To deflate: press the black button located on the

compressor pipe, near the valve connection.

►ꢀ Lift the spare wheel towards the back of the

boot.

Accessing the spare wheel

►ꢀ Take the wheel out of the boot.

Putting the spare wheel back in place

If after 7 minutes the pressure of 2 bar is

not reached, the tyre is damaged; contact

a dealer or a qualified workshop for

assistance.

The punctured wheel cannot be put under

the boot floor.

►ꢀ Once the correct pressure is reached, put the

switch in position "O".

The spare wheel is stored in the boot, under the

►ꢀ Remove the kit and stow it.

►ꢀ Refit the cap on the valve.

floor.

To access the spare wheel, first refer to the Tool

kit section.

Spare wheel

The spare wheel is a ‘space-saver’ wheel.

►ꢀ Put the spare wheel back in place in its

housing.

Scan the QR Code on page 3 to view

explanatory videos.

►ꢀ Slacken the nut on the bolt by a few turns.

►ꢀ Position the fastening device (nut and bolt) in

the middle of the wheel.

Removing the spare wheel

For more information on the Tool kit, refer

to the corresponding section.

►ꢀ Tighten the central nut sufficiently to retain

the wheel correctly.

►ꢀ Put the tool box back in place in the middle of

the wheel and clip it in place.

Removing a wheel

Parking the vehicle

►ꢀ Slacken the central nut.

►ꢀ Remove the fastening device (nut and bolt).

Immobilise the vehicle where it does not

obstruct traffic: the ground must be level,

stable and non-slippery.

165

In the event of a breakdown

Select mode P on the automatic gearbox to

lock the wheels, apply the parking brake,

unless it is set to automatic mode, and switch

off the ignition.

►ꢀ To remove the wheel bolt cover on each of the

bolts, use tool 7 (alloy wheels).

Check that the parking brake indicator lamps

on the instrument panel are on fixed.

The occupants must get out of the vehicle and

wait where they are safe.

►ꢀ Fit security socket 2 on wheelbrace 5 to

slacken the security bolt.

►ꢀ Slacken the other bolts using the

wheelbrace 5 only.

If necessary, place a chock under the wheel

diagonally opposite the wheel to be changed.

Never go underneath a vehicle raised using a

jack; use an axle stand.

►ꢀ Extend jack 6 until its head comes into contact

with jacking point A or B; contact area A or B on

the vehicle must be properly inserted into the

central part of the head of the jack.

Wheel with wheel trim

When removing the wheel, first remove

the wheel trim by pulling at the valve aperture

using the wheelbrace.

►ꢀ Raise the vehicle until there is sufficient space

between the wheel and the ground to easily admit

the spare (not punctured) wheel.

When refitting the wheel, refit the wheel trim,

starting by placing its aperture in line with the

valve and then pushing it into place all round

its edge with the palm of your hand.

Ensure that the jack is stable. If the

ground is slippery or loose, the jack may

slip or collapse - risk of injury!

►ꢀ Place the foot of jack 6 on the ground and

ensure that it is directly below the front A or

rear B jacking point on the underbody, whichever

is closest to the wheel to be changed.

Take care to position the jack strictly at

one of the jacking points A or B under the

vehicle, ensuring that the head of the jack is

centred under the contact area on the vehicle.

Otherwise, there is a risk of damage to the

vehicle and/or of the jack collapsing - risk of

injury!

166

In the event of a breakdown

►ꢀ Remove the bolts and store them in a clean

place.

►ꢀ Tighten the security bolt using the

wheelbrace 5 equipped with a security socket 2.

►ꢀ Tighten the other bolts using the wheelbrace 5

only.

►ꢀ Fit the wheel on the hub.

►ꢀ Screw in the bolts by hand as far as possible.

►ꢀ Pre-tighten the security bolt using the

wheelbrace 5 equipped with a security socket 2.

►ꢀ Pre-tighten the other bolts using the

wheelbrace 5 only.

►ꢀ Remove the wheel.

Fitting a wheel

►ꢀ Refit the bolt covers to each of the bolts

(depending on equipment).

Fitting a steel or "space-saver" type spare

wheel

►ꢀ Store the tools.

After changing a wheel

With a "space-saver" type spare wheel

If the vehicle is fitted with alloy wheels, the

washers A do not make contact with the steel

or "space-saver" type spare wheel. The wheel

is held in place by the conical contact surface

B of each bolt.

Deactivate certain driving aid functions (Active

Safety Brake, Adaptive cruise control, etc.).

Do not exceed the maximum authorised speed

of 50 mph (80 km/h) or the maximum distance

of 50 miles (80 km).

►ꢀ Lower the vehicle again fully.

►ꢀ Fold jack 6 and remove it.

167

In the event of a breakdown

Driving with more than one "space-saver" type

spare wheel is prohibited.

Changing a bulb must only be done with

the ignition off and after the headlamp /

lamp has been switched off for several

minutes - risk of serious burns!

If you need to replace this type of bulb,

you must contact a dealer or a qualified

workshop.

Do not touch the LED technology bulbs - risk of

electrocution!

Visit a dealer or a qualified workshop.

Have the tightening of the spare wheel's

bolts and its tyre pressure checked.

Have the punctured tyre examined. After

inspection, the technician will advise you on

whether the tyre can be repaired or if it must

be replaced.

Do not touch the bulb directly with your

fingers; use a lint-free cloth.

It is essential only to use anti-ultraviolet (UV)

type bulbs, so as not to damage the headlamp.

Always replace a failed bulb with a new bulb

of the same type and specification. To avoid

lighting imbalance, replace the bulbs in pairs.

Never look too closely at the light beam of

LED technology lamps - risk of serious eye

injury!

After changing a bulb

Changing a bulb

To refit, carry out the operations in

reverse order to removal.

In some weather conditions (e.g. low

temperature or humidity), misting on the

internal surface of the glass of the headlamps

and rear lamps is normal, and will disappear

after the lamps have been on for a few

minutes.

Close the protective cover very carefully to

guarantee the sealing of the lamps.

Light-emitting diode (LED)

headlamps and lamps

Depending on version, the affected types of

The headlamps have polycarbonate

lenses with a protective coating:

headlamps/lamps are:

– DS ACTIVE LED VISION headlamps.

– Offset daytime running lamps.

– Direction indicator side repeaters.

– Side spotlamps.

–

Do not clean them with a dry or abrasive

cloth, nor with detergent or solvent products.

– Use a sponge and soapy water or a pH

neutral product.

– Full LED technology rear lamps.

– Third brake lamp.

– When using a high-pressure washer on

persistent marks, do not keep the lance

directed towards the headlamps, lamps or

their edges for too long, so as not to damage

their protective coating and seals.

– Rear screen sidelamps (DS Cornet).

– Number plate lamps.

In the event of a breakdown -> Spare wheel for Your DS 9 4 Door First Generation (2020-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals