Get IN AN EMERGENCY -> REPLACING A BULB Guide for Fiat Doblo Van 2010-2022

Emergency braking

HAZARD WARNING

LIGHTS

REPLACING A BULB

(for versions/markets, where provided)

In the event of emergency braking

the hazard warning lights come on

automatically, as do the and

GENERAL

INSTRUCTIONS

They are turned on by pressing switch

A fig. 152, regardless of the position

of the ignition key. Warning lights

and are lit up in the instrument

panel when this device is activated.

Press switch A again to turn the lights

off.

Before replacing a bulb check the

contacts for oxidation;

warning lights in the panel.

The function switches off automatically

when the nature of the braking

burnt bulbs must be replaced by

others of the same type and power;

always check the headlight beam

alignment after replacing a bulb;

changes. This function complies with

the relevant legislation currently in force.

IMPORTANT The use of hazard warning

lights is governed by the highway

code of the country you are in. Comply

with legal requirements.

when a light is not working, check

that the corresponding fuse is intact

before changing a bulb. For the location

of fuses, refer to the paragraph “If a

fuse blows” in this section.

120) 121)

24) 25)

IMPORTANT The headlight inner

surface might be slightly misted: this

does not indicate a fault, it is a natural

phenomenon due to low temperature

and the air humidity level. Misting

will disappear rapidly when the

headlights are turned on. The presence

of drops inside the headlights indicates

infiltration of water. Contact a Fiat

Dealership.

F0V0513

152

144

TYPES OF BULBS

E

Halogen bulbs: to remove the bulb,

release the clip holding the bulb in

place.

Various types of bulbs are fitted to your

vehicle fig. 153:

WARNING

120) Modifications or repairs to the electric

system that are not carried out properly

or do not take the system technical

specifications into account can cause

malfunctions leading to the risk of fire.

121) Halogen bulbs contain pressurised

gas; in the case of breakage they may

burst.

WARNING

24) Halogen bulbs must be handled by

holding the metallic part only. If the

transparent bulb is touched with the

fingers, its lighting intensity is reduced and

life of the bulb may be compromised. In

the case of accidental contact, rub the

lamp with a cloth and alcohol and leave to

dry.

F0V0027

153

A

B

Glass bulbs: they are press-fitted.

Pull to extract.

25) Where possible, it is advisable to have

bulbs changed at a Fiat Dealership. Proper

operation and direction of the external

lights are essential for driving in safety and

comply with law.

Bayonet type bulbs: to remove from

its holder, press the bulb, turn it

anticlockwise, then remove.

C

D

Tubular bulbs: release them from their

contacts to remove.

Halogen bulbs: to remove the bulb,

release the clip holding the bulb in

place.

145

Bulbs

Use

Type

H7

Power

55 W

13 W

21 W

5 W

Ref. Figure

Main beam headlights

Dipped headlights

E

B

A

B

A

B

A

E

H7

Daytime running lights / side lights

Front direction indicators

Side direction indicators

Rear direction indicators

Rear fog light

W21W

WY21W

WY5W

PY21W

W16W

P21/5W

P21W

W5W

21 W

16 W

5 W

Reverse

Rear side lights

Brake lights

21 W

5 W

3rd brake light wing

3rd brake light swinging

3rd brake light swinging (for privacy glass)

Front fog lights (for versions/markets where provided)

W5W

5 W

Xenon 6 W

H11

6 W

55 W

146

SIDE LIGHTS/DAYTIME RUNNING

LIGHTS

DIPPED HEADLIGHTS

REPLACING AN

EXTERIOR BULB

To replace the bulb, proceed as follows:

remove the protective cover B fig.

154;

For the type of bulb and relevant power

rating, see “Changing a bulb”.

remove the protective cover C fig.

154;

disconnect the electrical connector;

FRONT LIGHT CLUSTERS

turn the bulb holder A fig. 155

anticlockwise and remove it;

release the bulb holder from the

side clips A fig. 156;

The front light clusters contain side

light, daytime running light, dipped,

main beam and direction indicator

bulbs fig. 154.

extract the bulb and replace it;

refit the new bulb, put the

bulb holder A fig. 155 back into place

and then refit the protective cover C fig.

154 properly.

fit the new bulb, ensuring that the

outline of the metal part coincides with

the grooves on the curve of the

headlight, pressing to engage it with the

side clips A fig. 156; then reconnect

the electrical connector;

refit the protective cover B fig. 154.

F0V0520

154

The bulbs are arranged inside the light

cluster as follows:

F0V0521

155

A

B

C

Main beam headlights:

Dipped headlights;

F0V0522

156

Direction indicators and side

lights/daytime running lights

To access the bulbs, remove the

snap-fitted covers.

147

DIRECTION INDICATORS

Front

MAIN BEAM HEADLIGHTS

FOG LIGHTS

(for versions/markets, where provided)

To replace the bulb, proceed as

follows:

IMPORTANT Go to a Fiat Dealership

to have the front fog light bulbs

replaced.

To replace the bulb, proceed as follows:

remove the protective cover A fig.

154;

remove the protective cover C fig.

154;

REAR LIGHT CLUSTERS

disconnect the electrical connector;

turn bulb holder A fig. 157

anticlockwise and remove it;

The rear light clusters contain the bulbs

for the side lights, direction indicators

and reversing/rear fog and brake lights.

To access the light clusters, proceed

as follows:

release the bulb holder from the

side clips A fig. 158;

extract the bulb, pushing it gently

and turning it anticlockwise;

extract the bulb and replace it;

fit the new bulb, ensuring that the

outline of the metal part coincides with

the grooves on the curve of the

headlight, pressing to engage it with the

side clips A fig. 158; then reconnect

the electrical connector;

replace the bulb and refit the bulb

holder A fig. 157 by turning it clockwise

and locking it properly into place;

open the rear doors;

undo the fixing screws A fig. 159;

refit the protective cover C fig. 154.

disconnect the electrical connector

and then remove the light cluster.

The bulbs are arranged inside the light

cluster fig. 160 as follows:

refit the protective cover A fig. 154.

A

B

C

D

Brake lights

Direction indicators

Reverse lights

Side/rear fog lights;

To access the bulbs, undo the 6 fixing

screws E fig. 160 and remove the

bulb holder.

F0V0523

157

Side

To change the bulb, push it in gently

and turn it anticlockwise (“bayonet”

type), then remove and replace it.

F0V0524

158

IMPORTANT Go to a Fiat Dealership to

have bulbs for the side direction

indicators replaced, because they are

located inside the wing mirror.

148

F0V0164

162

for versions with high roof and swing

doors, remove the pressure-fit plastic

guard A fig. 163 and rubber cap B

fig. 163, using a screwdriver, release

the retaining tags as shown in the figure

and remove the unit;

F0V0034

F0V0525

159

160

THIRD BRAKE LIGHTS

To replace the bulb proceed as follows:

for versions with tailgate, undo the

two fixing screws A fig. 161 and

remove the unit;

for versions with wing doors, remove

the rubber caps B fig. 162 and

manoeuvre the holding tabs C, then

remove the unit;

F0V0231

163

manoeuvre the appropriate tabs and

remove the bulb holder;

F0V0163

161

remove the snap-fitted bulb and

replace.

149

NUMBER PLATE LIGHTS

(for hatchback

versions)

NUMBER PLATE LIGHTS

(for versions with wing

doors)

REPLACING AN

INTERIOR BULB

For the type of bulb and power rating,

see "Changing a bulb".

Proceed as follows to replace the bulbs

A fig. 164:

Proceed as follows to replace the bulbs

A fig. 166:

FRONT ROOF LIGHT

Roof light with movable lens

Proceed as follows to replace the

bulbs:

remove roof light A fig. 167 working

at the points indicated by the arrows;

F0V0179

F0V0036

164

166

manoeuvre the holding tabs at the

points indicated by the arrows, and

remove the bulb holder;

manoeuvre the holding tabs at the

points indicated in the diagram, and

remove the lens by lifting to the left;

turn the bulb holder B fig. 165

anticlockwise, then remove bulb C.

remove the bulbs by releasing them

from the side contacts; insert the new

bulbs and make sure they are correctly

clamped between these contacts.

F0V0070

167

open the cover B fig. 168 as

indicated;

replace the bulb C fig. 169 releasing

the side contacts, insert the new bulb

and make sure that it is correctly locked

between the contacts;

close the cover and secure the roof

light into its housing, making sure it

locks properly into place.

F0V0037

165

150

REAR ROOF LIGHT

To replace the bulb, proceed as follows:

remove roof light A fig. 172 working

at the points indicated by the arrows;

F0V0071

F0V0073

168

170

F0V0075

172

open the cover B fig. 173 as

indicated;

F0V0072

F0V0074

169

171

Roof light with spot lights (where

provided)

close flap B fig. 171 and fix roof light

A fig. 170 in its housing, making sure

that it locks into place.

Proceed as follows to replace the

bulbs:

operate in the points indicated by

the arrows and remove light A fig. 170;

F0V0071

173

open protective flap B fig. 171;

replace the bulb C fig. 174 releasing

the side contacts, insert the new bulb

and make sure that it is correctly locked

between the contacts;

replace the bulbs C releasing them

from the side contacts making sure that

the new bulbs are correctly secured

between the contacts;

151

Download User Manual App

IN AN EMERGENCY -> REPLACING A BULB for Your Fiat Doblo Van 2010-2022

Related Topics

IN AN EMERGENCY

Popular Owner Manuals

Latest Owner Manuals