Get In Case of Emergency Guide for Fiat Fiorino SUV Third Generation (2015-2026)

IN CASE OF EMERGENCY

Have a flat tyre or a burnt-out bulb?

HAZARD WARNING LIGHTS ....... 145

CHANGING A WHEEL ................ 145

FIX & GO AUTOMATIC KIT .......... 149

REPLACING A BULB.................. 151

REPLACING AN EXTERIOR

BULB ....................................... 155

REPLACING INTERIOR BULBS.... 158

FUSE REPLACEMENT ................ 160

EMERGENCY STARTING............ 168

FUEL CUT-OFF SYSTEM ............ 169

TOWING THE VEHICLE .............. 169

At times, a problem such as these may

interfere with your driving experience.

The pages on emergencies can help

you to deal with critical situations

independently and calmly.

In an emergency we recommend that

you call the toll-free number found on

the Warranty Booklet.

It is also possible to call the

00 800 3428 0000 freephone number

to search the nearest Fiat Dealership.

144

switches off automatically when the

nature of the braking changes.

This function complies with the relevant

legislation currently in force.

safely. The ground must be flat and

sufficiently compact;

switch off the engine and pull the

handbrake;

engage first gear or reverse;

before getting out of the vehicle,

put on the reflective safety jacket (if

required by the regulations in force). In

any case, follow the road safety laws

in force in the country where you are

driving;

HAZARD WARNING

LIGHTS

They are turned on by pressing switch

(A) fig. 173, regardless of the position

of the ignition key.

CHANGING A WHEEL

Warning lights

and

are lit up in

The vehicle is originally equipped with

the Fix&Go Automatic quick tyre repair

kit (see instructions in the next section).

As an alternative, the vehicle may have

a normal-sized spare wheel.

the instrument panel when this device

is activated. Press the switch (A) again

to turn the lights off.

indicate that the vehicle has broken

down using the devices required by the

law in the current country (e.g. warning

triangle, hazard lights, etc.);

Wheel changing and correct use of

the jack and spare wheel call for some

precautions, as listed below.

121) 122) 123) 124) 125) 126) 127)

WARNING The use of hazard warning

lights is governed by the highway code

of the country you are in. Comply with

legal requirements.

For Fiorino Cargo versions: lift lever

(A) fig. 174 and move the left front

set backrest forward to retrieve the

tool bag located behind the backrest:

release the elastic strap and take the

tool bag to the wheel to be changed;

27) 28)

JACK

Please note that:

the jack weight is 1.76 kg;

the jack requires no adjustment;

the jack cannot be repaired and in

the event of a fault it must be replaced

by another genuine one;

no tool other than its cranking device

may be fitted on the jack.

173

F0T0049

WHEEL REPLACEMENT

PROCEDURE

To change a wheel, proceed as

follows:

stop the vehicle in a position that is

not dangerous for oncoming traffic

where you can change the wheel

Emergency braking (for

versions/markets where provided)

In the event of emergency braking

the hazard warning lights come on

automatically, as do the

warning lights in the panel. The function

174

F0T0119

and

for Fiorino Combi and Qubo versions:

open the rear swing doors, take the

145

tool bag fig. 175 located on the left of

the boot by releasing the elastic straps

and take to the wheel to be replaced;

177

F0T0168

for vehicles with alloy rims, remove

the hub cap;

loosen the fixing bolts of the wheel to

be replaced by about one turn, using

the spanner provided;

175

F0T0206

take wheel spanner (B) fig. 176 and

the extension with pentagonal fitting

(C); inside the load area, fit extension

(C) on bolt (A); use spanner (B) to lower

the wheel by unwinding the wire;

for wheels with steel rims, remove

the wheel cap;

176

F0T0922

use the wheel spanner (B) to remove

the wheel from the vehicle fig. 177;

unscrew knob (D) fig. 178 and

release the rim from bracket (E),

removing it from the hole of the rim;

178

F0T0923

turn the jack to open it partially and

then position it under the vehicle at the

references (A) fig. 179 near the wheel

to be replaced;

146

avoid grazing your hands against the

ground. The moving components of

the jack (screws and joints) can also

cause injuries: avoid touching them. If

you come into contact with lubricating

grease, clean yourself thoroughly;

fully loosen the four fastening bolts

and remove the wheel;

for vehicles with alloy rim, fit the hub

cap;

turn the jack handle to lower the

vehicle, and remove the jack;

use the wrench provided to fasten

the bolts completely in a criss-cross

fashion as shown in fig. 182.

make sure the contact surfaces

between spare wheel and hub are

clean so that the fastening bolts will not

come loose;

for vehicles with steel rims, fit the

standard wheel by inserting the first

bolt (B) fig. 181 two threads into the

hole closest to the inflation valve (A);

179

F0T0125

operate the jack so as to open it until

the groove (A) fig. 180 of the jack is

correctly inserted in the lower profile (B)

on the side member;

182

F0T0128

At the end of the operation

fix bracket (A) fig. 183 to the wheel

after passing it through the hole, insert

the threaded pin into one of the bolt

holes and secure by tightening knob

(B);

180

F0T0126

181

F0T0282

warn anybody nearby that the vehicle

is about to be lifted. They must stay

clear and not touch the vehicle until it is

back on the ground;

operate the jack and lift the vehicle

until the wheel is several centimetres

off the ground. When turning the crank,

ensure that it rotates freely in order to

fit the hub cap, making sure that the

symbol (on the cup) aligns with the

inflation valve, and then insert the other

three bolts;

tighten the bolts using the spanner

provided;

147

Therefore, always place both the jack and

punctured wheel in the dedicated housing.

122) It is extremely dangerous to attempt

to change a wheel on the side of the

vehicle next to the driving lane: make sure

that the vehicle is at a sufficient distance

from the road, to avoid being run over.

123) The spare wheel (for

versions/markets, where provided) is

specifically for your vehicle. Therefore, it

must not be used on other models. Do

not use spare wheels of other models on

your vehicle. The spare wheel must be

used only in an emergency. Use of the

spare wheel must be strictly reduced to

the necessary minimum.

124) Use your hazard lights, warning

triangle, etc to show that your vehicle is

stationary. Passengers should get out

of the vehicle, particularly if it is heavily

loaded, and wait for the wheel to be

changed away from the traffic. If you

are on a slope or uneven surface, place

wedges or other suitable objects under

the wheels to secure the vehicle. Have

the wheel repaired and refitted as soon as

possible. Do not apply grease to the bolt

threads before fitting: they could come

unscrewed.

125) The jack is a tool developed and

designed only for changing a wheel, if a

tyre gets punctured or damaged, on the

vehicle with which it is supplied or on other

vehicles of the same model. Any other

use, e.g. to jack up other vehicle models

or different things, is strictly prohibited.

Never use it to carry out maintenance or

repairs under the vehicle or to change

summer/winter wheels and vice versa: we

advise you to contact a Fiat Dealership.

Never go under the raised vehicle: use

183

F0T0924

185

F0T0926

for vehicles with alloy wheels, take

check that the position of the

the adapter (D) fig. 184 and introduce

the bracket (E) into the adapter (D),

insert the pin into the hole and fix with

the knob (F);

replaced wheel under the platform is

correct (the lifting system is equipped

with a clutch to limit the end of the

stroke, incorrect positioning may

jeopardise safety);

lift the wheel by fastening the bolt (A)

fig. 176;

put jack and tools back in the

specific tool bag;

reposition the tool bag behind the

left seat (Cargo versions) or in the boot

(Combi versions);

secure the tool box to the hooks.

184

F0T0925

WARNING

position the wheel vertically and rest

the fitted adaptor on the inside of the

rim, then using the screws provided

fix the wheel to the adaptor fig. 185.

Tighten the screws with the wheel

spanner;

121) If left in the passenger compartment,

the punctured wheel and jack constitute a

serious risk to the safety of occupants in

the event of accidents or sharp braking.

148

one cartridge (A) containing sealant

and fitted with: transparent tube for

injecting the sealant (D) and sticker (C)

with the wording "Max. 80 km/h" to be

placed in a clearly visible position (e.g.

on the dashboard) after repairing the

tyre;

it only in the positions indicated. Do not

use the jack for loads higher than the one

shown on its label. Never start the engine

with vehicle raised. If the vehicle is raised

more than necessary, everything can

become more unstable, with the risk of the

vehicle dropping violently. Thus, lift the

vehicle only as needed in order to access

the spare wheel.

28) Contact a Fiat Dealership as soon as

possible to have the correct tightening of

the fixing bolts checked.

FIX & GO

AUTOMATIC KIT

one compressor (B);

128) 129)

126) Incorrect hub cap assembly may

cause it to come off when the vehicle is

moving. Never tamper with the inflation

valve. Never introduce tools of any kind

between rim and tyre. Check tyre and

space-saver wheel pressures regularly,

complying with the values given in the

"Technical specifications" chapter.

127) Never use the space-saver spare

wheel for more than strictly necessary and

never exceed 80 km/h. On the space-

saver wheel there is an orange label,

summarising the main warnings regarding

usage restrictions. Never remove or cover

the label. Warning! For temporary use only!

80 km/h max.! Replace by standard wheel

as soon as possible.

a pair of gloves located in the hose

compartment of the cartridge (D).

29)

The Fix&Go automatic quick tyre repair

kit is located in a special container in

the boot.

The Fix&Go Automatic kit is located

in the luggage compartment on the

left rear wheel arch (A) fig. 186 (Fiorino

Combi and Qubo versions).

On Fiorino Cargo versions, the Fix&Go

repair kit is located behind the driver's

seat.

D

A

C

B

187

F0T0931

TYRE REPAIRING AND

PRESSURE RESTORING

PROCEDURE

Proceed as follows:

IMPORTANT

stop the vehicle in a position that

is not dangerous for oncoming traffic

where you can carry out the procedure

safely. The ground must be flat and

sufficiently compact;

stop the engine, engage the hazard

warning lights and the parking brake;

before getting out of the vehicle,

put on the reflective safety jacket (if

27) When turning the jack handle make

sure that it can turn freely without scraping

your hand against the ground. The moving

components of the jack ("worm screw"

and joints) can also cause injuries: avoid

touching them. If you come into contact

with lubricating grease, clean yourself

thoroughly.

186

F0T0355

The quick tyre repair kit contains

fig. 187:

149

required by the regulations in force). In

any case, follow the road safety laws

in force in the country where you are

driving;

button (H) and lifting the cartridge (A)

upwards fig. 191.

G

insert the sealant cartridge (A)

into the corresponding compressor

compartment (B)and press it down

hard fig. 187. Remove the speed limit

sticker (C) and apply it in a clearly

visible position fig. 188;

A

E

M

189

F0T0933

H

plug the electrical connector (F)

fig. 190 into the 12V socket of the

191

F0T0935

8 km / 5 mi

vehicle and start the vehicle engine;

If the pressure gauge (G) fig. 189

indicates a pressure lower than

1.8 bar / 26 psi 15 minutes after

starting the compressor, switch off the

compressor, disconnect the sealant

tube (D) from the tyre valve and remove

the cartridge (A) from the compressor

fig. 191.

188

F0T0932

wear the gloves;

Move the vehicle by approximately

10 m to promote the distribution of

sealant; stop the vehicle safely, operate

the handbrake and restore pressure

using the black inflation pipe (L) fig. 192

to reach the required pressure. If also

in this case, the pressure is lower

than 1.8 bar / 26 psi 15 minutes after

turning on, do not resume driving but

contact a Fiat Dealership.

remove the cap from the tyre valve

and connect and screw the transparent

tube of the sealant (D) fig. 187 onto the

valve. If a 250 ml cartridge is present

the housing of the transparent tube

is provided with removable ring to

facilitate extraction. Make sure that the

ON/OFF button (E) fig. 189 is in the off

position (button not pressed);

190

F0T0934

operate the compressor by pressing

the ON/OFF button (E) fig. 189.

When the pressure shown in Owner

Handbook or on the specific label

appears on the pressure gauge (G),

stop the compressor by pressing the

ON/OFF button (E) again;

disconnect the cartridge (A) from the

compressor, by pressing the release

150

Press the air release button (M) fig. 189

to adjust any tyre overpressure.

IMPORTANT

CARTRIDGE

REPLACEMENT

Proceed as follows:

only use original Fix&Go cartridges,

which can be purchased from the Fiat

Dealership.

to remove the cartridge (A) fig. 187

press the release button (H) fig. 191

and lift it.

29) The sealant fluid is effective with

external temperatures from -40°C to

+50°C. The sealant fluid has an expiry date

and must be replaced periodically. It is

possible to repair tyres with damage on

the tread up to a maximum diameter of

6 mm. Show the cartridge and the label

to the personnel who will handle the tyre

treated with the repair kit.

192

F0T0936

After driving for about 8 km / 5

miles, position the vehicle in a safe

and suitable area and engage the

handbrake. Take the compressor

and restore pressure using the black

inflation tube (L) fig. 192.

If the pressure shown is higher than

1.8 bar / 26 psi, restore the pressure

and drive safely to a Fiat Dealership

as soon as possible. If, however, the

pressure is lower than 1.8 bar / 26 psi,

do not resume driving but contact a

Fiat Dealership.

REPLACING A BULB

GENERAL

INSTRUCTIONS

WARNING

130) 131) 132) 133) 134)

128) The information required by the

applicable regulation is indicated on the

Fix&Go kit package label. Carefully read

the label on the cartridge before use,

avoid improper use. Fix&Go is subject

to expiration and must be replaced

periodically. The kit should be used by

adults and cannot be used by children.

129) IMPORTANT: Do not exceed

Before replacing a bulb check the

contacts for oxidation;

burnt bulbs must be replaced by

others of the same type and power;

always check the headlight beam

direction after changing a bulb;

when a light is not working, check

that the corresponding fuse is intact

before replacing a bulb. For the

location of fuses, refer to the paragraph

"Replacing fuses" in this chapter.

80 km/h. Avoid sudden acceleration or

braking. The kit provides a temporary

repair, therefore the tyre must be

PROCEDURE FOR

RESTORING THE

PRESSURE

examined and repaired by a specialist as

soon as possible. Before using the kit,

ensure that the tyre is not excessively

damaged and that the rim is in good

condition, otherwise do not use it and

call roadside assistance. Do not remove

foreign bodies from the tyre. Do not let the

compressor turned on for more than 20

consecutive minutes - overheating hazard.

Proceed as follows:

stop the vehicle safely, as shown

above, and operate the handbrake;

extract the black inflation tube (L)

fig. 192 and screw it firmly onto the tyre

valve. Follow the instructions shown in

fig. 190 and fig. 192.

WARNING A slight misting may

appear on the internal surface of the

headlight: this does not indicate a fault

and is caused by low temperature

and the degree of humidity in the air.

Misting will rapidly disappear when

151

the headlights are switched on. The

presence of drops inside the headlights

indicates infiltration of water. Contact a

Fiat Dealership.

WARNING

130) Modifications or repairs to the electric

system that are not carried out properly

or do not take the system technical

specifications into account can cause

malfunctions leading to the risk of fire.

131) Halogen bulbs contain pressurised

gas, in the case of breakage they may

burst causing glass fragments to be

projected outwards.

132) Halogen bulbs must be handled

holding the metallic part only. Touching

the transparent part of the bulb with your

fingers may reduce the intensity of the

emitted light and even reduce the lifespan

of the bulb. In the event of accidental

contact, wipe the bulb with a cloth

moistened with alcohol and let the bulb

dry.

133) Where possible, it is advisable to

have bulbs changed at a Fiat Dealership.

The correct operation and direction of the

external lights are absolutely essential for

the safety of the car and of compliance

with the law.

134) Only replace the light bulbs when the

engine is off and in a position that does

not interfere with traffic and lets you safely

replace them (see the description in the

“Replacement” paragraph). Also ensure

that the engine is cold, to prevent the risk

of burns.

152

^Bꢀ ^{ULB TYPES}

Various types of bulbs are fitted to your vehicle:

All-glass bulb: (type A) these are pressure fitted - pull to remove.

Bayonet bulb: (type B) to remove them press the bulb and turn it

anticlockwise.

Cylindrical bulbs: (type C) release them from their contacts to

remove.

Halogen bulbs: (type D) release the fastening clip from its housing to

remove the bulb.

Halogen bulbs: (type E) release the fastening clip from its housing to

remove the bulb.

153

^Lꢀ^{ight bulbs}

Light bulbs

Type

H4

Power

55W

60W

5W

Figure ref.

Main beam headlights

Dipped beam headlights

Front side lights

E

D

A

B

A

B

C

A

B

H4

W5W

PY21W

WY5W

PY21W

P4/21W

P21W

W5W

P21W

Front direction indicators

Side direction indicators

Rear direction indicators

Tail lights/rear fog lights

Stop

2IW

5W

21W

4W/21W

21W

5W

Number plate

3rd brake light (*)

5W

Reverse gear

21W

Front fog lights (for versions/markets where

provided)

H1

C

55W

10W

E

C

Front roof light with movable lens

Front ceiling light with spot lights (for

versions/markets, where provided)

C

Rear roof light (for versions/markets, where

provided)

C

10W

C

(*) WARNING For versions/markets, where provided, in the versions with tinted windows replace the whole light unit, as it is sealed.

154

extract the bulb (B) and replace it;

refit the new bulb, put the bulb

holder (A) fig. 194 back into place

and then refit the protective cover (A)

fig. 193 properly.

REPLACING AN

EXTERIOR BULB

For the type of bulb and relevant power

rating, see the “Changing a bulb”

paragraph.

FRONT LIGHT CLUSTERS

The front light clusters fig. 193 contain

sidelight, dipped beam, main beam and

direction indicator bulbs.

195

F0T0095

The bulbs are arranged inside the light

cluster as follows:

(A) Side lights/tail lights and

main/dipped beam headlights;

(B) Direction indicators.

refit the new bulb by inserting it on

connector (B) and then make the

contour of the metallic part mate with

the grooves obtained on the headlight

parabola;

194

F0T0094

DIPPED BEAM/MAIN

BEAM HEADLIGHTS

To change the bulb (double filament),

proceed as follows:

remove the protective cover (A)

fig. 193;

release the bulb holder clip;

extract the bulb (A) fig. 195 from the

connector (B) and replace it;

refit the bulb holder clip and refit the

protective lid (A) fig. 193.

DIRECTION INDICATORS

Front

To replace the bulb, proceed as

follows:

turn the protective lid (B) fig. 193

anticlockwise;

extract the bulb (A) fig. 196 and

193

F0T0093

replace it;

correctly refit the protective cover (B).

SIDE LIGHTS

To replace the bulb, proceed as

follows:

remove the protective cover (A)

fig. 193;

turn the bulb holder (A) fig. 194

anticlockwise and extract it;

155

196

F0T0096

198

F0T0098

199

F0T0100

Side

FOG LIGHTS

To replace the bulb, proceed as

follows:

(for versions/markets, where provided)

adjust the lens (A) fig. 197 to

compress in the clip (B) fig. 198, then

pull the cluster outwards;

WARNING Contact Fiat Dealership to

replace the front fog lights.

turn the bulb holder (C)

anticlockwise, extract the press-fit bulb

(D) and replace it;

refit the bulb holder (C) in the lens

and turn it clockwise;

REAR LIGHT CLUSTERS

The rear light clusters contain the bulbs

for the side lights, direction indicators

and reversing/rear fog and brake lights.

To access the light clusters, proceed

as follows:

refit the cluster making sure that the

internal clip (B) clicks into position.

open the rear swing doors;

loosen the screws (A) fig. 200 as to

access the light cluster (B) fig. 199;

remove the connector (C) fig. 199.

197

F0T0097

156

202

F0T0102

THIRD BRAKE LIGHTS

Fiorino versions with swing door

Contact Fiat Dealership to replace the

third brake lights fig. 203.

200

F0T0099

201

F0T0101

203

F0T0103

The bulbs are arranged inside the light

cluster fig. 201 and fig. 202 as follows:

A Brake lights;

Qubo versions with tailgate

To replace the bulbs, proceed as

follows fig. 204 - fig. 205:

B Direction indicators;

C Reverse lights;

D Side/rear fog lights.

Pull the 5 tabs (E) fig. 201 outwards to

access the bulbs.

157

REPLACING

INTERIOR BULBS

For the type of bulb and relevant power

rating, see “Changing a bulb”.

FRONT CEILING LIGHT

Ceiling light with movable lens

To replace the bulbs, proceed as

follows:

204

F0T0212

206

F0T0104

operate the holding tabs at the points

indicated by the arrows, and remove

the bulb holder;

A

B

208

F0T0106

C

205

F0T0443

extract the ceiling light (A) fig. 208 by

operating in the points shown by the

arrows;

open the lid (B) fig. 209 as shown;

remove bulb (C) fig. 209 by releasing

it from the side contacts, then insert

the new bulb and make sure it is

correctly clamped between these

contacts;

open the tailgate and loosen the two

retaining screws (A);

disconnect the electrical connector

207

F0T0105

(B);

turn the bulb holder (B) fig. 207

anticlockwise, then remove bulb (C).

release the retainer tab (C) and open

the bulb holder assembly;

extract the snap-fitted bulb and

replace it

close the lid and secure the ceiling

light into its housing, making sure it

locks properly into place.

NUMBER PLATE LIGHTS

To replace the bulbs (A) fig. 206,

proceed as follows:

158

are correctly secured between the

contacts;

re-close the flap (B) fig. 211 and

fasten the ceiling light (A) fig. 210 in its

housing, making sure that it locks into

place.

209

F0T0458

212

F0T0107

Front ceiling light with map reading

lights

(for versions/markets, where provided)

To replace the bulbs, proceed as

follows:

remove bulb (C) fig. 213 by releasing

it from the side contacts, then insert

the new bulb and make sure it is

correctly clamped between these

contacts;

211

F0T0144

close the cover (B) fig. 213 and

secure the ceiling light into its housing,

making sure it locks properly into place;

close the cover (B) and secure the

ceiling light into its housing, making

sure it locks properly into place.

REAR CEILING LIGHT

Fiorino Cargo versions

To replace the bulb, proceed as

follows:

extract the ceiling light (A) fig. 212 by

operating in the points shown by the

arrows;

open the lid (B) fig. 213 as shown;

210

F0T0143

operate in the points shown by the

arrow and remove ceiling light (A)

fig. 210;

open protective flap (B) fig. 211;

213

F0T0458

replace the bulbs (C) by releasing

them from the side contacts and

making sure that the new bulbs

159

REMOVABLE CEILING

LIGHT

(for versions/markets, where provided)

To replace the bulb, proceed as

follows:

press button (A) fig. 214 and extract

the removable courtesy light (B);

extract the ceiling light by operating

in the points shown by the arrows;

change the bulb (C) fig. 215 releasing

it from the side contacts and making

sure the new bulb is correctly fastened

between the contacts;

BOOT COURTESY LIGHT

(for versions/markets, where provided)

To change the bulb, proceed as

follows:

FUSE

REPLACEMENT

GENERAL INFORMATION

For fuse replacement, contact a Fiat

Dealership.

open the tailgate;

remove the light (A) fig. 216 levering

in the point shown by the arrow.

open the protection (B) replace the

snap-fitted bulb;

close the cover (B) on the lens;

refit the ceiling light (A) by inserting it

in its correct position firstly on one side

and then pressing on the other until it

clicks into place.

135) 136) 137) 138) 139) 140)

30)

Fuses protect the electrical system:

they intervene (blow) in the event of

a failure or improper action on the

system.

Check the state of the corresponding

fuse when a device does not work: the

filament (A) fig. 217 should be intact.

If it is not, replace the blown fuse with

another with the same ampere rating

(same colour).

AUTO

(B) intact fuse.

(C) fuse with damaged filament.

To change a fuse, use the tongs (D)

located in the tool box or the Fix&Go

container (for versions/markets where

provided).

214

F0T0108

216

F0T0251

Refer to the tables on the following

pages to identify the protective fuse.

WARNING The Natural Power system

components are protected by specific

fuses. Contact a Fiat Dealership for

replacement.

AUTO

215

F0T0109

160

217

F0T0015

219

F0T0172

ENGINE BAY FUSE BOX

The fuse box is on the right-hand side

of the engine.

press the tab (A) fig. 219 and remove

the fuse box protective cover (B);

move the cover towards the

headlight, turning it anticlockwise (as

shown by the arrow) and then remove

it fig. 220;

Removing the fuse box lid

the fuse box can be accessed in this

manner fig. 222.

31)

220

F0T0173

218

F0T0171

Refitting the fuse box lid

Proceed as follows to refit the lid:

Proceed as follows:

insert the two tabs (A) fig. 221 in the

respective seats located on the fuse

box;

remove protective cover (A) fig. 218

the positive battery terminal by lifting it

upwards;

refasten the tab (B) in the

corresponding seat until it clicks.

161

IMPORTANT

30) Never replace a faulty fuse with metal

wires or anything else.

31) If you need to clean the engine

compartment, take care not to directly hit

the fuse box with the water jet.

221

F0T0174

WARNING

135) For fuse replacement, contact a Fiat

Dealership.

136) If the replaced fuse blows again,

contact a Fiat Dealership.

137) Never replace a fuse with another

with a higher amp rating; RISK OF FIRE.

138) If a general fuse (MEGA-FUSE, MIDI-

FUSE, MAXI-FUSE) blows contact a Fiat

Dealership.

139) Before replacing a fuse, make sure

that the ignition key has been removed

and that all the other services are switched

off and/or disengaged.

140) Contact Fiat Dealership if a safety

system (airbags, brakes), engine system

(engine, transmission) or steering system

general protection fuse blows.

162

222

F0T0181

ꢀ

PROTECTED DEVICE

Spare (trailer kit)

Horns

FUSE

F09

AMPERE

10

15

F10

Main beam headlights

Rear power socket

F14

F15

163

In Case of Emergency for Your Fiat Fiorino SUV Third Generation (2015-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals