Get In Case of Emergency -> Fix & Go Automatic Kit Guide for Fiat Fiorino SUV Third Generation (2015-2026)

one cartridge (A) containing sealant

and fitted with: transparent tube for

injecting the sealant (D) and sticker (C)

with the wording "Max. 80 km/h" to be

placed in a clearly visible position (e.g.

on the dashboard) after repairing the

tyre;

it only in the positions indicated. Do not

use the jack for loads higher than the one

shown on its label. Never start the engine

with vehicle raised. If the vehicle is raised

more than necessary, everything can

become more unstable, with the risk of the

vehicle dropping violently. Thus, lift the

vehicle only as needed in order to access

the spare wheel.

28) Contact a Fiat Dealership as soon as

possible to have the correct tightening of

the fixing bolts checked.

FIX & GO

AUTOMATIC KIT

one compressor (B);

128) 129)

126) Incorrect hub cap assembly may

cause it to come off when the vehicle is

moving. Never tamper with the inflation

valve. Never introduce tools of any kind

between rim and tyre. Check tyre and

space-saver wheel pressures regularly,

complying with the values given in the

"Technical specifications" chapter.

127) Never use the space-saver spare

wheel for more than strictly necessary and

never exceed 80 km/h. On the space-

saver wheel there is an orange label,

summarising the main warnings regarding

usage restrictions. Never remove or cover

the label. Warning! For temporary use only!

80 km/h max.! Replace by standard wheel

as soon as possible.

a pair of gloves located in the hose

compartment of the cartridge (D).

29)

The Fix&Go automatic quick tyre repair

kit is located in a special container in

the boot.

The Fix&Go Automatic kit is located

in the luggage compartment on the

left rear wheel arch (A) fig. 186 (Fiorino

Combi and Qubo versions).

On Fiorino Cargo versions, the Fix&Go

repair kit is located behind the driver's

seat.

187

F0T0931

TYRE REPAIRING AND

PRESSURE RESTORING

PROCEDURE

Proceed as follows:

IMPORTANT

stop the vehicle in a position that

is not dangerous for oncoming traffic

where you can carry out the procedure

safely. The ground must be flat and

sufficiently compact;

stop the engine, engage the hazard

warning lights and the parking brake;

before getting out of the vehicle,

put on the reflective safety jacket (if

27) When turning the jack handle make

sure that it can turn freely without scraping

your hand against the ground. The moving

components of the jack ("worm screw"

and joints) can also cause injuries: avoid

touching them. If you come into contact

with lubricating grease, clean yourself

thoroughly.

186

F0T0355

The quick tyre repair kit contains

fig. 187:

149

required by the regulations in force). In

any case, follow the road safety laws

in force in the country where you are

driving;

button (H) and lifting the cartridge (A)

upwards fig. 191.

insert the sealant cartridge (A)

into the corresponding compressor

compartment (B)and press it down

hard fig. 187. Remove the speed limit

sticker (C) and apply it in a clearly

visible position fig. 188;

189

F0T0933

plug the electrical connector (F)

fig. 190 into the 12V socket of the

191

F0T0935

8 km / 5 mi

vehicle and start the vehicle engine;

If the pressure gauge (G) fig. 189

indicates a pressure lower than

1.8 bar / 26 psi 15 minutes after

starting the compressor, switch off the

compressor, disconnect the sealant

tube (D) from the tyre valve and remove

the cartridge (A) from the compressor

fig. 191.

188

F0T0932

wear the gloves;

Move the vehicle by approximately

10 m to promote the distribution of

sealant; stop the vehicle safely, operate

the handbrake and restore pressure

using the black inflation pipe (L) fig. 192

to reach the required pressure. If also

in this case, the pressure is lower

than 1.8 bar / 26 psi 15 minutes after

turning on, do not resume driving but

contact a Fiat Dealership.

remove the cap from the tyre valve

and connect and screw the transparent

tube of the sealant (D) fig. 187 onto the

valve. If a 250 ml cartridge is present

the housing of the transparent tube

is provided with removable ring to

facilitate extraction. Make sure that the

ON/OFF button (E) fig. 189 is in the off

position (button not pressed);

190

F0T0934

operate the compressor by pressing

the ON/OFF button (E) fig. 189.

When the pressure shown in Owner

Handbook or on the specific label

appears on the pressure gauge (G),

stop the compressor by pressing the

ON/OFF button (E) again;

disconnect the cartridge (A) from the

compressor, by pressing the release

150

Press the air release button (M) fig. 189

to adjust any tyre overpressure.

IMPORTANT

CARTRIDGE

REPLACEMENT

Proceed as follows:

only use original Fix&Go cartridges,

which can be purchased from the Fiat

Dealership.

to remove the cartridge (A) fig. 187

press the release button (H) fig. 191

and lift it.

29) The sealant fluid is effective with

external temperatures from -40°C to

+50°C. The sealant fluid has an expiry date

and must be replaced periodically. It is

possible to repair tyres with damage on

the tread up to a maximum diameter of

6 mm. Show the cartridge and the label

to the personnel who will handle the tyre

treated with the repair kit.

192

F0T0936

After driving for about 8 km / 5

miles, position the vehicle in a safe

and suitable area and engage the

handbrake. Take the compressor

and restore pressure using the black

inflation tube (L) fig. 192.

If the pressure shown is higher than

1.8 bar / 26 psi, restore the pressure

and drive safely to a Fiat Dealership

as soon as possible. If, however, the

pressure is lower than 1.8 bar / 26 psi,

do not resume driving but contact a

Fiat Dealership.

REPLACING A BULB

GENERAL

INSTRUCTIONS

WARNING

130) 131) 132) 133) 134)

128) The information required by the

applicable regulation is indicated on the

Fix&Go kit package label. Carefully read

the label on the cartridge before use,

avoid improper use. Fix&Go is subject

to expiration and must be replaced

periodically. The kit should be used by

adults and cannot be used by children.

129) IMPORTANT: Do not exceed

Before replacing a bulb check the

contacts for oxidation;

burnt bulbs must be replaced by

others of the same type and power;

always check the headlight beam

direction after changing a bulb;

when a light is not working, check

that the corresponding fuse is intact

before replacing a bulb. For the

location of fuses, refer to the paragraph

"Replacing fuses" in this chapter.

80 km/h. Avoid sudden acceleration or

braking. The kit provides a temporary

repair, therefore the tyre must be

PROCEDURE FOR

RESTORING THE

PRESSURE

examined and repaired by a specialist as

soon as possible. Before using the kit,

ensure that the tyre is not excessively

damaged and that the rim is in good

condition, otherwise do not use it and

call roadside assistance. Do not remove

foreign bodies from the tyre. Do not let the

compressor turned on for more than 20

consecutive minutes - overheating hazard.

Proceed as follows:

stop the vehicle safely, as shown

above, and operate the handbrake;

extract the black inflation tube (L)

fig. 192 and screw it firmly onto the tyre

valve. Follow the instructions shown in

fig. 190 and fig. 192.

WARNING A slight misting may

appear on the internal surface of the

headlight: this does not indicate a fault

and is caused by low temperature

and the degree of humidity in the air.

Misting will rapidly disappear when

151

In Case of Emergency -> Fix & Go Automatic Kit for Your Fiat Fiorino SUV Third Generation (2015-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals