Get In Case of Emergency -> Changing a Wheel Guide for Fiat Fiorino SUV Third Generation (2015-2026)

switches off automatically when the

nature of the braking changes.

This function complies with the relevant

legislation currently in force.

safely. The ground must be flat and

sufficiently compact;

switch off the engine and pull the

handbrake;

engage first gear or reverse;

before getting out of the vehicle,

put on the reflective safety jacket (if

required by the regulations in force). In

any case, follow the road safety laws

in force in the country where you are

driving;

HAZARD WARNING

LIGHTS

They are turned on by pressing switch

(A) fig. 173, regardless of the position

of the ignition key.

CHANGING A WHEEL

Warning lights

and

are lit up in

The vehicle is originally equipped with

the Fix&Go Automatic quick tyre repair

kit (see instructions in the next section).

As an alternative, the vehicle may have

a normal-sized spare wheel.

the instrument panel when this device

is activated. Press the switch (A) again

to turn the lights off.

indicate that the vehicle has broken

down using the devices required by the

law in the current country (e.g. warning

triangle, hazard lights, etc.);

Wheel changing and correct use of

the jack and spare wheel call for some

precautions, as listed below.

121) 122) 123) 124) 125) 126) 127)

WARNING The use of hazard warning

lights is governed by the highway code

of the country you are in. Comply with

legal requirements.

For Fiorino Cargo versions: lift lever

(A) fig. 174 and move the left front

set backrest forward to retrieve the

tool bag located behind the backrest:

release the elastic strap and take the

tool bag to the wheel to be changed;

27) 28)

JACK

Please note that:

the jack weight is 1.76 kg;

the jack requires no adjustment;

the jack cannot be repaired and in

the event of a fault it must be replaced

by another genuine one;

no tool other than its cranking device

may be fitted on the jack.

173

F0T0049

WHEEL REPLACEMENT

PROCEDURE

To change a wheel, proceed as

follows:

stop the vehicle in a position that is

not dangerous for oncoming traffic

where you can change the wheel

Emergency braking (for

versions/markets where provided)

In the event of emergency braking

the hazard warning lights come on

automatically, as do the

warning lights in the panel. The function

174

F0T0119

and

for Fiorino Combi and Qubo versions:

open the rear swing doors, take the

145

tool bag fig. 175 located on the left of

the boot by releasing the elastic straps

and take to the wheel to be replaced;

177

F0T0168

for vehicles with alloy rims, remove

the hub cap;

loosen the fixing bolts of the wheel to

be replaced by about one turn, using

the spanner provided;

175

F0T0206

take wheel spanner (B) fig. 176 and

the extension with pentagonal fitting

(C); inside the load area, fit extension

the wheel by unwinding the wire;

for wheels with steel rims, remove

the wheel cap;

176

F0T0922

use the wheel spanner (B) to remove

the wheel from the vehicle fig. 177;

unscrew knob (D) fig. 178 and

release the rim from bracket (E),

removing it from the hole of the rim;

178

F0T0923

turn the jack to open it partially and

then position it under the vehicle at the

references (A) fig. 179 near the wheel

to be replaced;

146

avoid grazing your hands against the

ground. The moving components of

the jack (screws and joints) can also

cause injuries: avoid touching them. If

you come into contact with lubricating

grease, clean yourself thoroughly;

fully loosen the four fastening bolts

and remove the wheel;

for vehicles with alloy rim, fit the hub

cap;

turn the jack handle to lower the

vehicle, and remove the jack;

use the wrench provided to fasten

the bolts completely in a criss-cross

fashion as shown in fig. 182.

make sure the contact surfaces

between spare wheel and hub are

clean so that the fastening bolts will not

come loose;

for vehicles with steel rims, fit the

standard wheel by inserting the first

bolt (B) fig. 181 two threads into the

hole closest to the inflation valve (A);

179

F0T0125

operate the jack so as to open it until

the groove (A) fig. 180 of the jack is

correctly inserted in the lower profile (B)

on the side member;

182

F0T0128

At the end of the operation

fix bracket (A) fig. 183 to the wheel

after passing it through the hole, insert

the threaded pin into one of the bolt

holes and secure by tightening knob

(B);

180

F0T0126

181

F0T0282

warn anybody nearby that the vehicle

is about to be lifted. They must stay

clear and not touch the vehicle until it is

back on the ground;

operate the jack and lift the vehicle

until the wheel is several centimetres

off the ground. When turning the crank,

ensure that it rotates freely in order to

fit the hub cap, making sure that the

symbol (on the cup) aligns with the

inflation valve, and then insert the other

three bolts;

tighten the bolts using the spanner

provided;

147

Therefore, always place both the jack and

punctured wheel in the dedicated housing.

122) It is extremely dangerous to attempt

to change a wheel on the side of the

vehicle next to the driving lane: make sure

that the vehicle is at a sufficient distance

from the road, to avoid being run over.

123) The spare wheel (for

versions/markets, where provided) is

specifically for your vehicle. Therefore, it

must not be used on other models. Do

not use spare wheels of other models on

your vehicle. The spare wheel must be

used only in an emergency. Use of the

spare wheel must be strictly reduced to

the necessary minimum.

124) Use your hazard lights, warning

triangle, etc to show that your vehicle is

stationary. Passengers should get out

of the vehicle, particularly if it is heavily

loaded, and wait for the wheel to be

changed away from the traffic. If you

are on a slope or uneven surface, place

wedges or other suitable objects under

the wheels to secure the vehicle. Have

the wheel repaired and refitted as soon as

possible. Do not apply grease to the bolt

threads before fitting: they could come

unscrewed.

125) The jack is a tool developed and

designed only for changing a wheel, if a

tyre gets punctured or damaged, on the

vehicle with which it is supplied or on other

vehicles of the same model. Any other

use, e.g. to jack up other vehicle models

or different things, is strictly prohibited.

Never use it to carry out maintenance or

repairs under the vehicle or to change

summer/winter wheels and vice versa: we

advise you to contact a Fiat Dealership.

Never go under the raised vehicle: use

183

F0T0924

185

F0T0926

for vehicles with alloy wheels, take

check that the position of the

the adapter (D) fig. 184 and introduce

the bracket (E) into the adapter (D),

insert the pin into the hole and fix with

the knob (F);

replaced wheel under the platform is

correct (the lifting system is equipped

with a clutch to limit the end of the

stroke, incorrect positioning may

jeopardise safety);

lift the wheel by fastening the bolt (A)

fig. 176;

put jack and tools back in the

specific tool bag;

reposition the tool bag behind the

left seat (Cargo versions) or in the boot

(Combi versions);

secure the tool box to the hooks.

184

F0T0925

WARNING

position the wheel vertically and rest

the fitted adaptor on the inside of the

rim, then using the screws provided

fix the wheel to the adaptor fig. 185.

Tighten the screws with the wheel

spanner;

121) If left in the passenger compartment,

the punctured wheel and jack constitute a

serious risk to the safety of occupants in

the event of accidents or sharp braking.

148

In Case of Emergency -> Changing a Wheel for Your Fiat Fiorino SUV Third Generation (2015-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals