Get IN AN EMERGENCY -> Replacing a Bulb Guide for Fiat Panda SUV Fourth Generation (2024-2026)

HAZARD WARNING

LIGHTS

REPLACING A BULB

WARNING

135) 136) 137)

43) 44)

135) Modifications or repairs to the electric

system that are not carried out properly

or do not take the system technical

specifications into account can cause

malfunctions leading to the risk of fire.

136) Halogen bulbs contain pressurised

gas, in the case of breakage they may

burst causing glass fragments to be

projected outwards.

137) Only replace the light bulbs when the

engine is off and in a position that does

not interfere with traffic and lets you safely

replace them (see the description in the

“Replacement chapter). Also ensure that

the engine is cold, to prevent the risk of

burns.

Press button (A) fig. 128 to switch the

lights on/off. Warning lights

GENERAL

INSTRUCTIONS

and

in the instrument panel are lit up when

the lights are ON.

Before replacing a bulb check the

contacts for oxidation;

burnt bulbs must be replaced by

others of the same type and power;

after replacing a headlight bulb,

always check its alignment;

WARNING The use of hazard warning

lights is governed by the highway

code of the country you are driving in:

comply with legal requirements.

when a light is not working, check

that the corresponding fuse is intact

before replacing a bulb. For the

location of fuses, refer to the "Fuses

replacement" chapter in this section.

NOTE the weather is cold or damp or

after heavy rain or after washing, the

surface of headlights or rear lights

may steam up and/or form drops of

condensation on the inside. This

is a natural phenomenon due to the

difference in temperature and humidity

between the inside and the outside

of the glass which does not indicate

a fault and does not compromise the

normal operation of lighting devices.

The mist disappears quickly when

the lights are turned on, starting from

the centre of the vent, extending

progressively towards the edges.

IMPORTANT

43) Halogen bulbs must be handled

holding the metallic part only. Touching

the transparent part of the bulb with your

fingers may reduce the intensity of the

emitted light and even reduce the lifespan

of the bulb. In the event of accidental

contact, wipe the bulb with a cloth

moistened with alcohol and let the bulb

dry.

44) Where possible, it is advisable to have

bulbs changed at a Fiat Dealership. The

correct operation and direction of the

external lights are absolutely essential for

the safety of the car and of compliance

with the law.

128

F1D0023

Emergency braking

In the event of emergency braking

the hazard warning lights switch on

automatically as well as the and

warning lights in the instrument panel.

The lights switch off automatically when

emergency braking ceases.

122

ꢀ

Light bulbs

Type

H4

Power

55W

21W

5W

Dipped/main beam headlights

Front side lights/Day lights (DRL)

Rear side lights

P21/5W

PY21W

W5W

Front direction indicators

Side turn light

21W

5W

Rear direction indicators

Stop

PY21W

P21/5W

LED

21W

‒

Third brake light

Fog lights

H11

55W

16W

5W

Reverse gear

W16W

C5W

Rear fog light

Number plate

123

FRONT LIGHT CLUSTERS

(except Panda Cross versions)

The bulbs are arranged inside the front

light cluster fig. 129 as follows:

(A) - Dipped beam/main beam

headlights/ direction indicators;

(B) - Daytime running lights (DRL);

(C) - Fog lights.

130

F1D0117

132

F1D0080

DIPPED/MAIN BEAMS

To replace the bulb, proceed as

follows:

refit the new bulb on the connector

making sure that it is locked correctly,

then reinsert the connector unit and the

bulb holder (B) in its housing;

remove cover (A) fig. 131;

then refit the cover (A).

DIRECTION INDICATORS

Front

129

F1D0134

To replace the bulb, proceed as

follows:

FRONT LIGHT CLUSTERS

(Panda Cross versions)

remove cover (B) fig. 131;

turn the bulb holder anticlockwise,

extract the bulb and replace it;

refit the new bulb on the connector

making sure that it is locked correctly,

then reinsert the connector in its

housing rotating it clockwise;

On the Panda Cross versions, the

bulbs are arranged inside the front light

cluster fig. 130 as follows:

(A) - Dipped beam/main beam

headlights/ direction indicators;

(B) - Fog lights;

131

F1D0079

push the connector + bulb holder

unit (B) fig. 132 downwards;

extract the bulb (C) from the

connector (D) and replace it;

(C) - Daytime running lights (DRL).

Side

To replace the bulb, proceed as

follows:

adjust the lens (A) fig. 133 to

compress in the clip B, then pull the

cluster outwards;

124

turn the bulb holder (C)

anticlockwise, extract the bulb and

replace it;

B

refit the bulb holder (C) in the lens

and turn it clockwise;

refit the cluster making sure that the

internal clip (B) clicks into position.

134

F1D0812

136

F1D0083

rotate and remove the bulb holder

(E), release and replace the bulb;

refit the new lamp and carry out

the procedure described previously in

reverse.

133

F1D0081

FOG LIGHTS

(Panda Cross versions)

To remove the fog light bulb, contact a

Fiat Dealership.

FOG LIGHTS

(for versions/markets, where provided -

except Panda Cross versions)

To replace the bulb, proceed as

follows:

135

F1D0813

SIDE LIGHTS / DAYTIME

RUNNING LIGHTS (DRL)

(for versions/markets, where provided -

except Panda Cross versions)

adjust the clip (C) fig. 136 and

disconnect the electrical connector (D);

steering the wheel fulling inwards,

turn the screws (A) fig. 134 and fig. 135

and move the inner wheel arch plastic

cover (B) aside to access the bulb.

To replace the bulb, proceed as

follows:

steering the wheel fulling inwards,

turn the screws (A) fig. 134 and fig. 135

and move the inner wheel arch plastic

cover (B) aside to access the bulb;

adjust the clip (C) fig. 137 and

disconnect the electrical connector (D);

125

rotate and remove the bulb holder

(E), release and replace the bulb;

undo the five screws (B) from their

seats and remove the bulb holder (C);

remove the bulbs, pushing them

slightly and turning them anti-

clockwise;

the two clips (press-fitted (D) fig. 139)

and release the connector;

refit the new lamp and carry out

the procedure described previously in

reverse.

REVERSING LIGHT/REAR

FOG LIGHT

138)

The reversing lights and rear fog lights

are located in the rear bumper. To

replace the bulb, proceed as follows:

access the bulb holder through the

underside of the rear bumper fig. 140;

137

F1D0084

refit the new lamp and carry out

the procedure described previously in

reverse.

DAYTIME RUNNING

LIGHTS (DRL)

(Panda Cross versions)

WARNING To change LED DRLs

contact a Fiat Dealership.

138

F1D0085

REAR LIGHT CLUSTERS

These contain the bulbs for the side

lights, brake lights and direction

indicators.

140

F1D0814

adjust the clip (C) fig. 141 and

disconnect the electrical connector (D);

turn the bulb holder (E) and remove

it, extract the bulb and replace it;

To replace the bulb proceed as follows:

undo the two screws (A) fig. 138

from their seats, pull gently outwards

until releasing the whole headlight from

139

F1D0086

126

141

F1D0088

142

F1D0089

144

F1D0785

refit the new lamp and carry out

the procedure described previously in

reverse.

open flap (B) fig. 145 and replace

the bulbs (C), releasing them from the

side contacts. Make sure that the new

bulbs are correctly secured between

the contacts;

re-close flap (B) fig. 145 and fasten

ceiling light (A) fig. 144 in position,

making sure that it locks into place.

THIRD BRAKE LIGHTS

These are located in the tailgate and

are LED lights. For replacement,

contact a Fiat Dealership.

NUMBER PLATE LIGHTS

To replace the bulbs, proceed as

follows:

143

F1D0090

remove lens (A) fig. 142;

FRONT CEILING LIGHT

Versions with multi-bulb ceiling

light

change the bulb (A) fig. 143,

releasing it from the side contacts;

Insert the new bulb and make sure

that it is correctly clamped between the

contacts, then refit the lens (A) fig. 143.

remove the ceiling light (A) fig. 144

working at the points indicated by the

arrows;

145

F1D0786

127

Versions with single bulb ceiling

light

To change the courtesy light bulb:

use a screwdriver to remove the

pressure-mounted lens unit;

release bulb cover (A) fig. 149 and

replace the 12V - 5 W bulb (B).

To change the bulbs, proceed as

follows:

operate in the point shown by the

arrow and remove roof light (A) fig. 146;

open flap (C) fig. 147 and replace

bulb (B), releasing it from the side

contacts.

insert the new bulb (B) and make

sure that it is correctly clamped

between the contacts;

re-close flap (C) and fasten ceiling

light (A) in position, making sure that it

locks into place.

147

F1D0788

open the protection (B) and replace

the bulb;

close the cover (B) on the lens;

refit the ceiling light (A) by inserting it

in its correct position firstly on one side

and then pressing on the other until it

clicks into place.

149

F1D0790

WARNING

Load compartment roof light

138) Before replacing the bulb, wait for the

catalytic converter to cool down: RISK OF

BURNS.

146

F1D0787

Boot courtesy light

To change the bulbs, proceed as

follows:

148

F1D0789

open the boot and extract the ceiling

light (A) fig. 148 working in the point

shown by the arrow;

128

IN AN EMERGENCY -> Replacing a Bulb for Your Fiat Panda SUV Fourth Generation (2024-2026)

Related Topics

IN AN EMERGENCY

Popular Owner Manuals

Latest Owner Manuals