Get IN AN EMERGENCY -> BULB REPLACEMENT Guide for Fiat Tipo 4 Door Second Generation (2015-2026)

extending progressively towards the

edges.

HAZARD WARNING

LIGHTS

BULB

REPLACEMENT

CONTROL

141) 142) 143)

Press button fig. 146 to switch the

lights on/off.

55)

IMPORTANT

GENERAL

INSTRUCTIONS

When the hazard warning lights are on,

the warning lights

141) Modifications or repairs to the electric

system that are not carried out properly

or do not take the system technical

specifications into account can cause

malfunctions leading to the risk of fire.

142) Halogen bulbs contain pressurised

gas, in the case of breakage they may

burst causing glass fragments to be

projected outwards.

143) Only replace the light bulbs when the

engine is off and in a position that does

not interfere with traffic and lets you safely

replace them (see the description in the

"Replacement” paragraph). Also ensure

that the engine is cold, to prevent the risk

of burns.

and

flash.

Before replacing a bulb check the

contacts for oxidation;

replace blown bulbs with others of

the same type and power;

after replacing a headlight bulb,

always check its alignment;

when a light is not working, check

that the corresponding fuse is intact

before changing the bulb. For the

location of fuses, refer to the paragraph

"If a fuse blows" in this chapter.

146

P2000315

WARNING When the weather is

WARNING The use of hazard warning

lights is governed by the highway

code of the country you are driving in:

comply with legal requirements.

cold or damp or after heavy rain or

washing, the surface of headlights or

rear lights may steam up and/or form

drops of condensation on the inside.

This is a natural phenomenon due

to the difference in temperature and

humidity between the inside and the

outside of the glass which does not

indicate an anomaly fault and does not

compromise the normal operation of

lighting devices. The mist disappears

quickly when the lights are turned on,

starting from the centre of the diffuser,

WARNING

55) Halogen bulbs must be handled

holding the metallic part only. Touching

the transparent part of the bulb with your

fingers may reduce the intensity of the

emitted light and even reduce the lifespan

of the bulb. In the event of accidental

contact, wipe the bulb with a cloth

moistened with alcohol and let the bulb

dry.

Emergency braking

In the event of emergency braking

the hazard warning lights switch on

automatically as well as the warning

lights

panel.

and

in the instrument

The lights switch off automatically when

emergency braking ceases.

149

BULB TYPES

ꢀ

The car is equipped with the following bulbs

Glass bulbs (type 1): they are press-fitted. Pull to extract.

Bayonet-type bulbs (type 2): to remove them from their holder,

press the bulb and turn it anticlockwise, then extract it.

Halogen bulbs (type 3): to remove the bulb, pull the connector and

extract it.

Halogen bulbs (type 4): to remove the bulb, turn it anticlockwise.

150

ꢀ

Light bulbs

Type

Power

Figure reference

Front side lights / Daytime running lights (DRL)

(versions with poly-elliptical headlights)

LED

–

Front side lights/Daytime running lights (DRL) (versions

with bi-parabolic headlights)

H15

15W

4

Front side lights / Daytime running lights (DRL) / Front

direction indicators (versions with LED headlights)

LED

H7

–

3

Main beam headlights (versions with LED headlights)

Main beam headlights (versions with poly-elliptical

headlights)

55W

Main beam headlights (versions with bi-parabolic

headlights)

H15

55W

4

Dipped headlights (versions with LED headlights)

Dipped headlights

LED

H7

–

3

2

1

–

2

–

55W

21W

5W

–

Front direction indicators

Side direction indicators

Number plate

PY21W

WY5W

W5W

LED (*)

P21W

PY21W

LED

Number plate

Rear side/brake light

21W

–

Rear direction indicators

Front side light (version with LED headlight)

151

Light bulbs

Type

W16W

LED

Power

16W

–

Figure reference

Reverse gear

1

–

Third brake light

Fog lights

H11

55W

16W

5W

4

1

Rear fog light

W16W

C5W

W5W

Front ceiling light

Front roof lights (sun visors)

Rear ceiling light

Boot courtesy light

Glove compartment light

(*) Where provided

5W

6W

5W

152

REPLACING AN

EXTERNAL BULB

Versions with

poly-elliptical headlights

Front bulb position

Dipped beam headlights

To replace the bulb (1) fig. 147,

proceed as follows:

extract the lamp-electrical connector

assembly;

disconnect the electrical connector

(3) and then replace the bulb (4);

reinsert the lamp-electrical connector

assembly in its housing, making sure

that it is blocked properly.

working from inside the engine

compartment, remove rubber

protection cap (1) fig. 148;

disconnect the electrical connector,

then release the retainer clip;

replace the bulb (2);

5

3

1

reconnect the electrical connector

and reconnect the lamp-connector

assembly in its housing;

re-engage the retainer clip, making

sure that it is secured;

refit the rubber cap (1).

4

2

149

P1030234-000-001

Front direction indicators

To replace the bulb (5) fig. 147,

proceed as follows:

turn the bulb-bulb holder assembly

(1) fig. 150 anticlockwise by

approximately 1/4 a turn and extract it;

replace lamp (2) by pressing it lightly

(axially) and simultaneously turning it

anticlockwise (bayonet fitting);

reinsert the bulb-bulb holder

assembly in its housing, then turn the

assembly (2) clockwise, making sure

that it is blocked.

147

P2000269

148

P1030234-000-000

1. Dipped beam headlights

2. Fog lights

3. Main beam headlights

4. Front side/Daytime running lights

(DRL)

5. Direction indicators

Main beam headlights

To replace the bulb (3) fig. 147,

proceed as follows:

working from inside the engine

compartment, remove rubber

protection cap (2) fig. 149;

153

disconnect the electrical connector

and replace the complete assembly;

reconnect the electrical connector to

the new bulb-bulb holder assembly;

fit the assembly in its housing,

turning it clockwise and making sure

that it is blocked properly;

refit the wheel arch inner plastic

cover and tighten the screws.

150

P2000185

152

P1030251-000-000

Front side/Daytime running lights

(DRL)

Front fog lamps

To replace the bulb, proceed as

follows:

Versions with

bi-parabolic headlights

Front bulb position

The daytime running light bulbs (4)

fig. 147 are LED to increase their

lifetime; therefore, they should not

require replacing. Contact the Fiat

Dealership in the event of any kind of

anomaly.

4

3

1

Side direction indicators

To replace the bulb, proceed as

follows:

press the lens (1) fig. 152 to

compress in the internal clip, then pull

the cluster outwards; take great care

not damage the paintwork;

turn the bulb holder (2) anticlockwise,

then extract the press-fit bulb (3) and

replace it;

refit the bulb holder (2) in the lens (1)

and turn it clockwise;

refit the cluster making sure that the

internal clip clicks into position.

151

P2000231

steering the wheel fulling inwards,

undo the screws (1) fig. 151 and move

the inner wheel arch plastic cover (2)

fig. 151 aside to access the bulb;

turn the bulb-bulb holder assembly

anticlockwise and then remove it sliding

it outwards;

2

153

P2000297

154

1. Dipped beam headlights

2. Fog lights

3. Main beam headlights/Daytime

running lights (DRL) / Side lights

4. Direction indicator

refit the rubber cap (1).

Left headlight

working from inside the engine

compartment, remove the rubber cap

from the dipped beam headlight bulb

(1) fig. 153;

extract the bulb, releasing it from the

retaining springs;

disconnect the electrical connector

and replace the bulb (1) fig. 153;

reconnect the electrical connector to

the new bulb;

reposition the assembly in the seat;

refit the rubber cap.

WARNING Only replace the bulb when

the engine is off. Also ensure that the

engine is cold, to prevent the risk of

burns.

Main beam headlights / Daytime

running lights (DRL)/ Positions

To replace the bulb (3) fig. 153,

proceed as follows:

Dipped beam headlights

Right headlight

working from inside the engine

compartment, remove rubber cap (1)

fig. 154;

To replace the bulb (1) fig. 153,

proceed as follows:

WARNING Only replace the bulb when

the engine is off. Also ensure that the

engine is cold, to prevent the risk of

burns.

Front direction indicators

To replace the bulb (4) fig. 153,

proceed as follows:

155

P2000231

154

08026J0025EM

rotate the bulb-bulb holder assembly

anticlockwise;

steering the wheel fulling inwards,

rotate the bulb-bulb holder assembly

undo the screws (1) fig. 155 and move

the inner wheel arch plastic cover (2)

fig. 155 aside to access the bulb;

remove the rubber cap;

disconnect the electrical connector;

extract the bulb, releasing it from the

retaining springs;

replace the "bayonet-fitted" bulb;

then insert the bulb-bulb holder

assembly in its housing and turn it

clockwise, making sure that it is locked

correctly.

anticlockwise and extract it;

disconnect the electrical connector

and replace the bulb-bulb holder

assembly (2);

reconnect the electrical connector to

the new assembly;

Fog lights

then insert the assembly in its

housing and turn it clockwise, making

sure that it is locked correctly;

replace the new bulb and carry out

the procedure described previously in

reverse.

To replace the bulbs, proceed as

follows:

steering the wheel fulling inwards,

155

undo the screws (1) fig. 155 and move

the inner wheel arch plastic cover (2)

fig. 155 aside to access the bulb;

turn the bulb-bulb holder assembly

(1) fig. 156 anticlockwise and then

remove it sliding it outwards;

1. Dipped beam headlights

2. Fog lights

3. Direction indicator / Daytime

running lights (DRL) / Side lights

4. Main beam headlights

For replacing these bulbs, contact a

Fiat Dealership.

Rear bulb position

157

08026J0005EM

turn the bulb holder (3) anticlockwise,

extract the press-fit bulb (4) and

replace it;

refit the bulb holder (3) in the lens

and turn it clockwise;

156

08026J0016EM

refit the cluster making sure that the

internal clip (2) clicks into position.

disconnect the electrical connector;

reconnect the connector to the

new assembly: then insert it, turning

it clockwise, ensuring that it locks

correctly;

159

P1030154-000-000

Versions with LED

headlights

Front bulb position

1. Positions

2. Tail lights/Brake lights

3. Direction indicator

4. Reverse gear

finally, refit the inspection flap.

4

3

1

Side direction indicators

To replace the bulb, proceed as

follows:

Versions with LED lights (where

provided) Contact a Fiat Dealership to

replace these bulbs.

1. Positions

2. Stop

3. Direction indicator

4. Reverse gear

adjust the lens (1) fig. 157 to

compress in the clip 2, then pull the

cluster outwards;

2

158

P2000312

156

(3) and remove the lens assembly from

the tailgate;

when replaced, refit the bulb holders

into the lens unit and re-tighten the

screws (4) fig. 162;

refit the assembly on the tailgate and

using the "L"-shaped key provided (1)

and the respective hexagonal bushing

(2), tighten the three fixing nuts (3);

finally, refit the inspection flap (1)

fig. 161, making sure that it is engaged

properly.

160

P2000311

Light cluster on body

Light cluster on tailgate

Tail and reversing lights

162

P1030165-000-000

Tail/Brake and indicators

To change one or more bulbs, proceed

as follows:

unscrew the four screws (4) fig. 162

and remove the bulb holder;

to replace the tail light (1)

fig. 163, press it lightly (axially) and

simultaneously turn it anticlockwise

(bayonet fitting);

To change one or more bulbs, proceed

as follows:

open the tailgate and remove the

press-fit moulding on the body, moving

it upwards (A) and then towards the

inside (B) as shown in fig. 164;

open the tailgate and use the

screwdriver provided to remove the

press-fit inspection flap (1) fig. 161;

161

P1030161-000-000

164

P2000068-000-000

163

P1030169-000-000

disconnect the central electrical

connector;

using the "L"-shaped key (1) fig. 162

and the respective hexagonal bushing

(2), provided, undo the three fixing nuts

using the L-shaped key (1) fig. 162

provided, unscrew the two screws (1)

fig. 165 and remove the light cluster;

to replace the reversing light (2),

simply pull the all-glass bulb out of its

holder;

157

disconnect the electric connector

and undo the two screws (2) fig. 166

then remove the bulb holder (3);

to replace the desired lamp, press

it lightly (axially) and simultaneously

turn it anticlockwise (bayonet fitting):

(4) - tail/brake lights, (5) - direction

indicators;

turn the bulb holder anticlockwise,

extract the bulb and replace it fig. 168;

refit the bulb holder and turn it

clockwise.

when replaced, refit the bulb holders

into the lens unit and tighten the two

screws (2);

166

P1030172-000-000

connect the electrical connector, fit

the lens unit on the body and tighten

the two screws (1) fig. 165 using the L-

shaped key (1);

fit the moulding by pressing on it

lightly until you feel it engage properly

with the body, then close the tailgate.

Third brake lights

The 3rd brake light bulbs are LED to

increase their lifetime; therefore, they

should not require replacing. Contact

the Fiat Dealership in the event of any

kind of anomaly.

168

P2000080-000-000

We recommend contacting a Fiat

Dealership to replace the bulb.

144)

Rear fog lights

To replace the rear fog light bulbs,

proceed as follows:

Number plate lights

To replace the bulbs, proceed as

follows:

access the bulb holder through the

underside of the rear bumper fig. 167;

use the screwdriver provided to

remove the lens unit (1) fig. 169;

turn the bulb holder (2) fig. 170

anticlockwise, extract the bulb (3) and

replace it;

refit the lens unit, pressing it lightly.

NOTE Before removing the lens unit,

put a protection (e.g. cloth) on the tip of

the screwdriver, in order not to damage

the lens itself.

165

P1030171-000-000

167

P2000183

158

Versions with LED lights (where

provided) Contact a Fiat Dealership to

replace these bulbs.

171

08026J0013EM

173

08026J0015EM

use tabs (2) fig. 172 and remove the

bulb holder assembly (3);

replace bulbs (4) fig. 173, pulling

them outwards;

insert the new bulbs, making sure

that they are locked correctly;

refit the bulb holder (3) fig. 172

correctly, making sure the tabs (2)click

into place;

169

P1030157-000-000

finally, refit ceiling light (1) fig. 171

in position, making sure that it locks

correctly.

Courtesy mirror light

To replace the bulbs, proceed as

follows:

lower the sun visor;

170

08026J0026EM

lift the mirror flap (1) fig. 174 and

remove the lens unit (2);

extract the bulb and replace it;

172

08026J0014EM

REPLACING AN

INTERNAL BULB

Multi-bulb front ceiling light

To replace the bulbs, proceed as

follows:

remove the ceiling light (1) fig. 171

working at the points indicated by the

arrows;

159

open the protection and replace the

bulb;

close the cover on the lens;

remove the lens assembly and

replace the press-fit bulb (1) fig. 177,

making sure that it locks correctly.

refit the unit in its position, inserting it

firstly on one side and then pressing on

the other side until it clicks into place.

Luggage compartment lights

To replace the bulb, proceed as

follows:

Rear ceiling light

To replace the bulb, proceed as

follows:

open the boot and extract the ceiling

light (1) fig. 178 working in the point

shown by the arrow;

open the protection and replace the

bulb (2);

174

08026J0020EM

operate in the points indicated by

the arrows and remove ceiling light (1)

fig. 176 complete with its frame;

refit the lens unit (2), making sure that

it locks correctly;

finally, lower the mirror flap (1).

Glove compartment light

To replace the bulb, proceed as

follows:

open the glove compartment;

operate in the point indicated by the

arrow fig. 175 and remove the lens

unit;

178

P1030178-000-000

176

08026J0027EM

close the cover on the lens;

refit ceiling light (1) in the correct

position, inserting it firstly on one side

and then pressing on the other side

until it clicks into place.

175

08026J0023EM

177

08026J0029EM

160

IN AN EMERGENCY -> BULB REPLACEMENT for Your Fiat Tipo 4 Door Second Generation (2015-2026)

Related Topics

IN AN EMERGENCY

Popular Owner Manuals

Latest Owner Manuals