Get Maintenance -> Light bulbs Guide for Hyundai I10 4 Door First Generation (2007-2012)

Maintenance

LIGHT BULBS

G220000AEN

CAUTION

If you don’t have necessary tools,

the correct bulbs and the expertise,

consult an authorized HYUNDAI

dealer. In many cases, it is difficult

to replace vehicle light bulbs

because other parts of the vehicle

must be removed before you can

get to the bulb. This is especially

true if you have to remove the head-

light assembly to get to the bulb(s).

Removing/installing the headlight

assembly can result in damage to

the vehicle.

WARNING - Working on

the lights

Prior to working on the light, firmly

apply the parking brake, ensure

that the ignition switch is turned to

the LOCK position and turn off the

lights to avoid sudden movement

of the vehicle and burning your fin-

gers or receiving an electric shock.

OPA071033

G220100AUN

Use only the bulbs of the specified

wattage.

Headlight, position light, turn sig-

nal light, front fog light bulb

replacement

✽

NOTICE

(1) Headlight (High/Low)

(2) Position light

(3) Front turn signal light

CAUTION

After heavy, driving rain or washing,

headlight and taillight lenses could

appear frosty. This condition is caused by

the temperature difference between the

lamp inside and outside. This is similar

to the condensation on your windows

inside your vehicle during the rain and

doesn’t indicate a problem with your

vehicle. If the water leaks into the lamp

bulb circuitry, have the vehicle checked

by an authorized HYUNDAI dealer.

Be sure to replace the burned-out

bulb with one of the same wattage

rating. Otherwise, it may cause

damage to the fuse or electric

wiring system.

7 63

Maintenance

(Continued)

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

• Wear eye protection when chang-

ing a bulb. Allow the bulb to cool

down before handling it.

G270A03O

OPA071062

G220101APA

1. Open the hood.

2. Disconnect the negative battery cable.

Headlight bulb

3. Using a socket wrench of the correct

size, remove the fasteners.

4. Pull out the front bumper.

WARNING - Halogen bulbs

• Halogen bulbs contain pressur-

ized gas that will produce flying

pieces of glass if broken.

• Always handle them carefully,

and avoid scratches and abra-

sions. If the bulbs are lit, avoid

contact with liquids. Never touch

the glass with bare hands.

Residual oil may cause the bulb

to overheat and burst when lit. A

bulb should be operated only

when installed in a headlight.

(Continued)

7 64

Maintenance

13. Connect the power connector to the

back of the headlight assembly.

14. Reinstall the headlight assembly to

the body of the vehicle.

OPA077036

OPA077047

5. Disconnect the power connector from

the back of the headlight assembly.

6. Remove the headlight bulb cover by

turning it counterclockwise.

7. Disconnect the headlight bulb socket-

connector.

8. Unsnap the headlight bulb retaining

wire by depressing the end and push-

ing it upward.

9. Remove the bulb from the headlight

assembly.

10. Install a new headlight bulb and snap

the headlight bulb retaining wire into

position by aligning the wire with the

groove on the bulb.

11. Connect the headlight bulb socket

connector.

12. Install the headlight bulb cover by

turning it clockwise.

7 65

Maintenance

Position light bulb

1. Remove the socket from the assembly

by pulling it out.

2. Remove the bulb by pulling it straight

out.

3. Insert a new bulb into the socket.

4. Install the socket into the assembly by

pushing it in.

Turn signal light bulb

1. Remove the socket from the assembly

by turning the socket counter clock-

wise until the tabs on the socket align

with the slots on the assembly.

OPA077056

OPA077037

G220102APA

G220200APA

Front fog light bulb replacement

1. Reach your hand into the front

bumper.

Side repeater light bulb replace-

ment (if equipped)

2. Remove the bulb from the socket by

pressing it in and rotating it until the

tabs on the bulb align with the slots in

the socket. Pull the bulb out of the

socket.

Type A

2. Remove the socket from the housing

by turning the socket counter clock-

wise until the tabs on the socket align

with the slots on the housing.

1. Remove the light assembly from the

body of the vehicle by prying the lens

and pulling the assembly out.

3. Insert a new bulb by inserting it into

the socket and rotating it until it locks

into place.

2. Disconnect the bulb electrical connec-

tor.

3. Remove the bulb by pulling it straight

out.

4. Install a new bulb in the socket.

4. Install the socket into the assembly by

aligning the tabs on the socket with the

slots in the assembly. Push the socket

into the assembly and turn the socket

clockwise.

3. Separate the socket and the lens part

by turning the socket counterclockwise

until the tabs on the socket align with

the slots on the lens part.

5. Install the socket in the housing by

aligning the tabs on the socket with the

slots in the housing. Insert the socket

into the housing and turn the socket

clockwise.

4. Remove the bulb by pulling it straight

out.

7 66

Maintenance

5. Insert a new bulb in the socket.

6. Reassemble the socket and the lens

part.

7. Connect the bulb electrical connector.

8. Reinstall the light assembly to the

body of the vehicle.

OPA071061

OPA071038

G220300APA

Type B

If the light bulb is not operating, have the

Rear combination light bulb

vehicle checked by an authorized replacement

HYUNDAI dealer.

(1) Stop light

(2) Back-up light

(3) Rear turn signal light

(4) Stop and tail light

(5) Rear fog light (if equipped)

7 67

Maintenance

Type A

OPA077040

OPA077041

Type B

OPA077039

1. Open the tailgate.

2. Loosen the light assembly retaining

screws with a philips head screwdriver.

3. Remove the rear combination light

assembly from the body of the vehicle.

OPA071040

OPA071041

4. Remove the socket from the assembly by turning the socket counterclockwise until

the tabs on the socket align with the slots on the assembly.

5. Remove the bulb from the socket by pulling out or pulling out after pressing it in and

rotating it counterclockwise until the tabs on the bulb align with the slots in the sock-

et.

6. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.

7. Install the socket in the assembly by aligning the tabs on the socket with the slots

in the assembly. Push the socket into the assembly and turn the socket clockwise.

8. Reinstall the light assembly to the body of the vehicle.

7 68

Maintenance

Room lamp (Type A)

Room lamp (Type B)

Luggage lamp

OPA077045

OPA077042

OPA077046

OPA077043

OPA077044

G220400AEN

G220500APA

High mounted stop light

replacement

License plate light bulb replace-

ment

If the light is not operating, have the vehi-

cle checked by an authorized HYUNDAI

dealer.

1. Using a flat-blade screwdriver, remove

the light assembly from the body of the

vehicle by prying the lens and pulling

the assembly out.

2. Separate the socket and the lens part

by turning the socket counterclockwise

until the tabs on the socket align with

the slots on the lens part.

3. Remove the bulb by pulling it straight

out.

4. Insert a new bulb in the socket.

5. Reassemble the socket and the lens

part.

6. Reinstall the light assembly to the

body of the vehicle.

7 69

Maintenance

G220600AUN

Interior light bulb replacement

1. Using a flat-blade screwdriver, gently

pry the lens from the interior light

housing.

2. Remove the bulb by pulling it straight

out.

WARNING

Prior to working on the Interior

Lights, ensure that the “OFF” but-

ton is depressed to avoid burning

your fingers or receiving an electric

shock.

3. Install a new bulb in the socket.

4. Align the lens tabs with the interior

light housing notches and snap the

lens into place.

CAUTION

Use care not to dirty or damage

lens, lens tab, and plastic housings.

7 70

Maintenance -> Light bulbs for Your Hyundai I10 4 Door First Generation (2007-2012)

Related Topics

Maintenance

Popular Owner Manuals

Latest Owner Manuals