Get Maintenance Guide for Hyundai I10 4 Door Second Generation (2013-2019)

Maintenance

ENGINE COMPARTMENT. . . . . . . . . . . . . . . . . . 7-3

PARKING BRAKE . . . . . . . . . . . . . . . . . . . . . . . . 7-29

• Checking the parking brake . . . . . . . . . . . . . . . . . . 7-29

AIR CLEANER . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-30

• Filter replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-30

CLIMATE CONTROL AIR FILTER . . . . . . . . . 7-32

• Filter inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-32

• Filter replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-32

WIPER BLADES . . . . . . . . . . . . . . . . . . . . . . . . . 7-34

• Blade inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-34

• Blade replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-34

MAINTENANCE SERVICES . . . . . . . . . . . . . . . . 7-4

• Owner’s responsibility . . . . . . . . . . . . . . . . . . . . . . . . 7-4

• Owner maintenance precautions . . . . . . . . . . . . . . . . 7-4

OWNER MAINTENANCE. . . . . . . . . . . . . . . . . . . 7-6

• Owner maintenance schedule . . . . . . . . . . . . . . . . . . . 7-6

SCHEDULED MAINTENANCE SERVICE. . . . . 7-8

• Normal maintenance schedule . . . . . . . . . . . . . . . . . . . 7-9

• Maintenance under severe usage conditions. . . . . . . 7-13

EXPLANATION OF SCHEDULED

MAINTENANCE ITEMS . . . . . . . . . . . . . . . . . . . 7-19

BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-38

• For best battery service . . . . . . . . . . . . . . . . . . . . . . . 7-38

• Battery capacity label . . . . . . . . . . . . . . . . . . . . . . . . 7-39

• Battery recharging . . . . . . . . . . . . . . . . . . . . . . . . . . 7-39

• Reset items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-40

TIRES AND WHEELS . . . . . . . . . . . . . . . . . . . . . 7-41

• Tire care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-41

• Recommended cold tire inflation pressures . . . . . . 7-41

• Checking tire inflation pressure. . . . . . . . . . . . . . . . . 7-43

• Tire rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-44

• Wheel alignment and tire balance . . . . . . . . . . . . . . 7-45

• Tire replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-45

• Wheel replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-46

• Tire traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-46

• Tire maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-47

ENGINE OIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

• Checking the engine oil level . . . . . . . . . . . . . . . . . . 7-19

• Changing the engine oil and filter . . . . . . . . . . . . . . . 7-23

ENGINE COOLANT. . . . . . . . . . . . . . . . . . . . . . . 7-23

• Checking the engine coolant level . . . . . . . . . . . . . . . 7-23

• Changing the engine coolant . . . . . . . . . . . . . . . . . . . 7-25

BRAKE/CLUTCH FLUID . . . . . . . . . . . . . . . . . . 7-26

• Checking the brake/clutch fluid level . . . . . . . . . . . 7-26

AUTOMATIC TRANSAXLE FLUID . . . . . . . . . 7-27

• Checking the automatic transaxle fluid level . . . . . 7-27

• Changing the automatic transaxle fluid . . . . . . . . . . 7-28

7

WASHER FLUID. . . . . . . . . . . . . . . . . . . . . . . . . . 7-29

• Checking the washer fluid level . . . . . . . . . . . . . . . . 7-29

• Tire sidewall labeling . . . . . . . . . . . . . . . . . . . . . . . . . 7-47

• Low aspect ratio tire . . . . . . . . . . . . . . . . . . . . . . . . . . 7-51

FUSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-52

• Instrument panel fuse replacement. . . . . . . . . . . . . . 7-53

• Engine compartment panel fuse replacement . . . . . 7-55

• Main fuse (multi fuse). . . . . . . . . . . . . . . . . . . . . . . . . 7-56

• Fuse/relay panel description. . . . . . . . . . . . . . . . . . . . 7-57

LIGHT BULBS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-69

• Headlight, position light, turn signal light, and

front fog light bulb replacement. . . . . . . . . . . . . . . 7-70

• Side repeater light bulb replacement . . . . . . . . . . . . 7-72

• Rear combination light bulb replacement . . . . . . . . 7-72

• Rear fog light bulb replacement . . . . . . . . . . . . . . . . 7-74

• High mounted stop light . . . . . . . . . . . . . . . . . . . . . . . 7-74

• License plate light bulb replacement . . . . . . . . . . . . 7-74

• Interior light bulb replacement . . . . . . . . . . . . . . . . . 7-75

APPEARANCE CARE . . . . . . . . . . . . . . . . . . . . . 7-76

• Exterior care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-76

• Interior care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-81

EMISSION CONTROL SYSTEM . . . . . . . . . . . . 7-82

• Crankcase emission control system. . . . . . . . . . . . . . 7-82

• Evaporative emission control system. . . . . . . . . . . . . 7-82

• Exhaust emission control system . . . . . . . . . . . . . . . . 7-83

7

Maintenance

ENGINE COMPARTMENT

■ Left-hand drive

1. Engine coolant reservoir

2. Engine oil filler cap

3. Brake/clutch fluid reservoir

4. Air cleaner

5. Fuse box

6. Positive battery terminal

7. Negative battery terminal

8. Windshield washer fluid reservoir

9. Radiator cap

■ Right-hand drive

10. Engine oil dipstick

11. Automatic transaxle dipstick*

* : if equipped

❈ The actual engine room in the vehicle may differ from the illustration.

OBA013006/OBA013006R

7 3

Maintenance

MAINTENANCE SERVICES

You should exercise the utmost care to

prevent damage to your vehicle and

injury to yourself whenever performing

any maintenance or inspection proce-

dures.

Inadequate, incomplete or insufficient

servicing may result in operational prob-

lems with your vehicle that could lead to

vehicle damage, an accident, or person-

al injury.

Owner’s responsibility

Owner maintenance precautions

Improper or incomplete service may

result in problems. This chapter gives

instructions only for the maintenance

items that are easy to perform.

✽

NOTICE

Maintenance Service and Record

Retention are the owner's responsibility.

We recommend in general that you have

your vehicle serviced by an authorized

HYUNDAI dealer.

✽

NOTICE

Improper owner maintenance during

the warranty period may affect warran-

ty coverage. For details, read the sepa-

rate Service Passport provided with the

vehicle. If you're unsure about any serv-

icing or maintenance procedure, we rec-

ommend that the system be serviced by

an authorized HYUNDAI dealer.

You should retain documents that show

proper maintenance has been performed

on your vehicle in accordance with the

scheduled maintenance service charts

shown on the following pages. You need

this information to establish your compli-

ance with the servicing and maintenance

requirements of your vehicle warranties.

Detailed warranty information is provided

in your Service Passport.

Repairs and adjustments required as a

result of improper maintenance or a lack

of required maintenance are not covered

when your vehicle is covered by warran-

ty.

7 4

Maintenance

WARNING - Maintenance

work

• Performing maintenance work on

a vehicle can be dangerous. You

can be seriously injured while

performing some maintenance

procedures. If you lack sufficient

knowledge and experience or the

proper tools and equipment to do

the work, we recommend that the

system be serviced by an author-

ized HYUNDAI dealer.

• Working under the hood with the

engine running is dangerous. It

becomes even more dangerous

when you wear jewelry or loose

clothing. These can become

entangled in moving parts and

result in injury. Therefore, if you

must run the engine while work-

ing under the hood, make certain

that you remove all jewelry (espe-

cially rings, bracelets, watches,

and necklaces) and all neckties,

scarves, and similar loose cloth-

ing before getting near the

engine or cooling fans.

7 5

Maintenance

OWNER MAINTENANCE

The following lists are vehicle checks and

inspections that should be performed at

the frequencies indicated to help ensure

safe, dependable operation of your vehi-

cle.

Any adverse conditions should be

brought to the attention of your dealer as

soon as possible.

These Owner Maintenance Checks are

generally not covered by warranties and

you may be charged for labor, parts and

lubricants used.

While operating your vehicle:

Owner maintenance schedule

When you stop for fuel:

• Check the engine oil level.

• Check the coolant level in the coolant

reservoir.

• Check the windshield washer fluid

level.

• Look for low or under-inflated tires.

• Note any changes in the sound of the

exhaust or any smell of exhaust fumes

in the vehicle.

• Check for vibrations in the steering

wheel. Notice any increased steering

effort or looseness in the steering

wheel, or change in its straight-ahead

position.

• Notice if your vehicle constantly turns

slightly or “pulls” to one side when trav-

eling on smooth, level road.

• When stopping, listen and check for

unusual sounds, pulling to one side,

increased brake pedal travel or “hard-

to-push” brake pedal.

WARNING

Be careful when checking your

engine coolant level when the

engine is hot. Scalding hot coolant

and steam may blow out under

pressure. This could cause burns

or other serious injury.

• If any slipping or changes in the oper-

ation of your transaxle occurs, check

the transaxle fluid level.

• Check automatic transaxle P (Park)

function.

• Check the parking brake.

• Check for fluid leaks under your vehicle

(water dripping from the air condition-

ing system during or after use is nor-

mal).

7 6

Maintenance

At least monthly:

• Check the coolant level in the engine

coolant reservoir.

• Check the operation of all exterior

lights, including the stoplights, turn sig-

nals and hazard warning flashers.

• Check the inflation pressures of all

tires including the spare.

At least twice a year

At least once a year:

• Clean the body and door drain holes.

• Lubricate the door hinges and checks,

and hood hinges.

• Lubricate the door and hood locks and

latches.

• Lubricate the door rubber weather-

strips.

• Check the air conditioning system.

• Inspect and lubricate the automatic

transaxle linkage and controls.

• Clean the battery and terminals.

(i.e., every Spring and Fall):

• Check the radiator, heater and air con-

ditioning hoses for leaks or damage.

• Check the windshield washer spray

and wiper operation. Clean the wiper

blades with clean cloth dampened with

washer fluid.

• Check the headlight alignment.

• Check the muffler, exhaust pipes,

shields and clamps.

• Check the lap/shoulder belts for wear

and function.

• Check for worn tires and loose wheel

lug nuts.

• Check the brake (and clutch) fluid

level.

7 7

Maintenance

SCHEDULED MAINTENANCE SERVICE

Follow the Normal Maintenance

Schedule if the vehicle is usually operat-

ed where none of the following conditions

apply. If any of the following conditions

apply, follow Maintenance Under Severe

Usage Conditions.

If your vehicle is operated under the

above conditions, you should inspect,

replace or refill more frequently than the

following Normal Maintenance Schedule.

After the periods or distance shown in

the chart, continue to follow the pre-

scribed maintenance intervals.

• Repeated short distance driving.

• Driving in dusty conditions or sandy

areas.

• Extensive use of brakes.

• Driving in areas where salt or other

corrosive materials are being used.

• Driving on rough or muddy roads.

• Driving in mountainous areas.

• Extended periods of idling or low

speed operation.

• Driving for a prolonged period in cold

temperatures and/or extremely humid

climates.

• More than 50% driving in heavy city

traffic during hot weather above 32°C

(90°F).

7 8

Maintenance

NORMAL MAINTENANCE SCHEDULE (FOR MEXICO)

MAINTENANCE

INTERVALS

Number of months or driving distance, whichever comes first

Months

6

6.5

10

I

12

13

20

I

18

19.5

30

I

24

26

40

I

30

32.5

50

I

36

39

60

I

42

45.5

70

I

48

52

80

I

Miles×1,000

Km×1,000

MAINTENANCE

ITEM

Drive belts *¹

Engine oil and engine oil filter *²

R

I

R

I

R

I

Air cleaner filter

R

I

R

I

Spark plugs

Replace every 160,000 km (100,000 miles) *³

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*¹: Adjust alternator and power steering (and water pump drive belt) and air conditioner drive belt (if equipped).

Inspect and if necessary correct or replace.

*²: Check the engine oil level and leak every 500 km (350 miles) or before starting a long trip.

*³: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

7 9

Maintenance

NORMAL MAINTENANCE SCHEDULE (FOR MEXICO) (CONT.)

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

6

12

13

20

18

19.5

30

24

26

40

30

32.5

50

36

39

60

42

45.5

70

48

52

80

Miles×1,000

Km×1,000

6.5

10

MAINTENANCE

ITEM

Valve clearance *⁴(if equipped)

Vapor hose and fuel filler cap

Vacuum hose

Inspect every 95,000 km (60,000 miles) or 48 months *³

I

R

I

Fuel filter *⁵

R

I

Fuel lines, hoses and connections

Inspect “Coolant level and leak” every day

Inspect “Water pump” when replacing the drive belt or timing belt

Cooling system

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*³: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

*⁴: Inspect for excessive valve noise and/or engine vibration and adjust if necessary. We recommend that the system be serviced

by an authorized HYUNDAI dealer.

*⁵: The fuel filter is considered to be maintenance free but periodic inspection is recommended for this maintenance schedule

depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of power, hard start-

ing problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an authorized HYUNDAI

dealer for details.

7 10

Maintenance

NORMAL MAINTENANCE SCHEDULE (FOR MEXICO) (CONT.)

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

6

12

13

20

18

19.5

30

24

26

40

30

32.5

50

36

39

60

42

45.5

70

48

52

80

Miles×1,000

Km×1,000

6.5

10

MAINTENANCE

ITEM

At first, replace at 210,000 km (120,000 miles) or 120 months:

after that, replace every 30,000 km (20,000 miles) or 24 months *⁷

Engine coolant *⁶

Battery condition

I

All electrical systems

Brake lines, hoses and connections

Brake pedal, clutch pedal (if equipped)

Parking brake

I

Brake/clutch(if equipped) fluid

Disc brakes and pads

I

Drum brakes and linings (if equipped)

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁶: When adding coolant, use only a qualified coolant additive for your vehicle and never mix hard water in the coolant filled at

the factory. An improper coolant mixture can result in serious malfunction or engine damage.

*⁷: For your convenience, it can be replaced prior to it’s interval when you do maintenance of other items.

7 11

Maintenance

NORMAL MAINTENANCE SCHEDULE (FOR MEXICO) (CONT.)

MAINTENANCE

INTERVALS

Number of months or driving distance, whichever comes first

Months

6

12

18

24

30

36

42

48

Miles×1,000

Km×1,000

6.5

13

19.5

26

32.5

39

45.5

52

MAINTENANCE

ITEM

10

20

30

40

50

60

70

80

Steering gear rack, linkage and boots

Driveshaft and boots

I

Tire (pressure & tread wear)

I

Front suspension ball joints

I

Bolt and nuts on chassis and body

Air conditioner refrigerant (if equipped)

I

Air conditioner compressor (if equipped)

Climate control air filter

I

R

Manual transaxle fluid *⁸(if equipped)

Inspect every 60,000 km (40,000 miles) or 48 months

Automatic transaxle fluid (if equipped)

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁸: Manual transaxle fluid should be changed anytime they have been submerged in water.

7 12

Maintenance

NORMAL MAINTENANCE SCHEDULE (EXCEPT MEXICO)

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

12

10

15

I

24

20

30

I

36

30

45

I

48

40

60

I

60

50

75

I

72

60

90

I

84

70

105

I

96

80

120

I

Miles×1,000

Km×1,000

MAINTENANCE

ITEM

Drive belts *¹

Except

Middle East

Replace every 15,000 km (10,000 miles) or 12 months

Replace every 10,000 km (6,000 miles) or 12 months

2

Engine oil and engine oil filter

*

Middle East

Except

Middle East

I

R

I

R

I

Air cleaner filter

Spark plugs

Middle East

R

Replace every 160,000 km (100,000 miles) *³

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*¹: Adjust alternator and power steering (and water pump drive belt) and air conditioner drive belt (if equipped).

Inspect and if necessary correct or replace.

*²: Check the engine oil level and leak every 500 km (350 miles) or before starting a long trip.

*³: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

7 13

Maintenance

NORMAL MAINTENANCE SCHEDULE (EXCEPT MEXICO) (CONT.)

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

12

10

15

24

20

30

36

30

45

48

40

60

50

75

72

60

90

84

70

96

80

Miles×1,000

Km×1,000

MAINTENANCE

ITEM

105

120

Valve clearance *⁴(if equipped)

Vapor hose and fuel filler cap

Vacuum hose

Inspect every 95,000 km (60,000 miles) or 48 months *³

I

R

I

Fuel filter *⁵

R

I

Fuel lines, hoses and connections

Inspect “Coolant level and leak” every day

Inspect “Water pump” when replacing the drive belt or timing belt

Cooling system

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*³: For your convenience, it can be replaced prior to it's interval when you do maintenance of other items.

*⁴: Inspect for excessive valve noise and/or engine vibration and adjust if necessary. We recommend that the system be serviced

by an authorized HYUNDAI dealer.

*⁵: The fuel filter is considered to be maintenance free but periodic inspection is recommended for this maintenance schedule

depends on fuel quality. If there are some important safety matters like fuel flow restriction, surging, loss of power, hard start-

ing problem etc, replace the fuel filter immediately regardless of maintenance schedule and consult an authorized HYUNDAI

dealer for details.

7 14

Maintenance

NORMAL MAINTENANCE SCHEDULE (EXCEPT MEXICO) (CONT.)

Number of months or driving distance, whichever comes first

MAINTENANCE

INTERVALS

Months

12

10

15

24

20

30

36

30

45

48

40

60

50

75

72

60

90

84

70

96

80

Miles×1,000

Km×1,000

MAINTENANCE

ITEM

105

120

At first, replace at 210,000 km (120,000 miles) or 120 months:

after that, replace every 30,000 km (20,000 miles) or 24 months *⁷

Engine coolant *⁶

Battery condition

I

All electrical systems

Brake lines, hoses and connections

Brake pedal, clutch pedal (if equipped)

Parking brake

I

Brake/clutch(if equipped) fluid

Disc brakes and pads

I

Drum brakes and linings (if equipped)

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁶: When adding coolant, use only a qualified coolant additive for your vehicle and never mix hard water in the coolant filled at

the factory. An improper coolant mixture can result in serious malfunction or engine damage.

*⁷: For your convenience, it can be replaced prior to it’s interval when you do maintenance of other items.

7 15

Maintenance

NORMAL MAINTENANCE SCHEDULE (EXCEPT MEXICO) (CONT.)

MAINTENANCE

INTERVALS

Number of months or driving distance, whichever comes first

Months

12

24

36

48

60

72

84

96

Miles×1,000

Km×1,000

10

20

30

40

50

60

70

80

MAINTENANCE

ITEM

15

30

45

60

75

90

105

120

Steering gear rack, linkage and boots

Driveshaft and boots

I

Tire (pressure & tread wear)

I

Front suspension ball joints

I

Bolt and nuts on chassis and body

Air conditioner refrigerant (if equipped)

Air conditioner compressor (if equipped)

Climate control air filter

I

R

Manual transaxle fluid *⁸(if equipped)

Inspect every 60,000 km (40,000 miles) or 48 months

Automatic transaxle fluid (if equipped)

I : Inspect and if necessary, adjust, correct, clean or replace.

R : Replace or change.

*⁸: Manual transaxle fluid should be changed anytime they have been submerged in water.

7 16

Maintenance

MAINTENANCE UNDER SEVERE USAGE CONDITIONS

The following items must be serviced more frequently on cars mainly used under severe driving conditions.

Refer to the chart below for the appropriate maintenance intervals.

I : Inspect and if necessary, adjust, correct, clean or replace

R : Replace or change

Maintenance

Maintenance item

Maintenance intervals

Driving condition

operation

Except Middle East

For Middle East

R

I

Every 7,500 km (4,600 miles) or 6 months

Every 5,000 km (3,100 miles) or 6 months

Engine oil and engine

oil filter

A, B, C, D, E,

F, G, H, I, J

Replace more frequently

depending on the condition

Replace more frequently

depending on the condition

Air cleaner filter

Spark plugs

C, E

B, H

C, D, E, F, G,

H, I, J

A, C, D, E, F,

G, H, I, J

Manual transaxle fluid (if equipped)

Automatic transaxle fluid (if equipped)

Steering gear rack, linkage and boots

Every 120,000 km (80,000 miles)

Every 100,000 km (62,500 miles)

Inspect more frequently

depending on the condition

C, D, E, F, G

7 17

Maintenance

operation

Maintenance item

Maintenance intervals

Driving condition

C, D, E, F, G

C, D, E, G, H

C, D, G, H

Inspect more frequently

depending on the condition

Inspect more frequently

depending on the condition

Inspect more frequently

depending on the condition

Inspect more frequently

depending on the condition

Front suspension ball joints

Disc brakes and pads, calipers and rotors

Drum brakes and linings (if equipped)

Parking brake

I

Inspect more frequently

depending on the condition

Replace more frequently

depending on the condition

Driveshaft and boots

I

C, D, E, F, G, H, I, J

C, E

Climate control air filter

R

Severe driving conditions

A : Repeated short distance driving

B : Extensive idling

F : More than 50 % driving in heavy city traffic during hot

weather above 32°C (90°F)

C : Driving in dusty, rough roads

D : Driving in areas using salt or other corrosive

materials or in very cold weather

E : Driving in sandy areas

G : Driving in mountainous areas

H : Towing a trailer

I : Driving for patrol car, taxi, commercial car or vehicle towing

J : Driving over 170 km/h (106 mile/h)

7 18

Maintenance

EXPLANATION OF SCHEDULED MAINTENANCE ITEMS

Engine oil and filter

Fuel filter

Vapor hose and fuel filler cap

The engine oil and filter should be

changed at the intervals specified in the

maintenance schedule. If the vehicle is

being driven in severe conditions, more

frequent oil and filter changes are

required.

A clogged filter can limit the speed at

which the vehicle may be driven, damage

the emission system and cause multiple

issues such as hard starting. If an exces-

sive amount of foreign matter accumu-

lates in the fuel tank, the filter may

require replacement more frequently.

After installing a new filter, run the engine

for several minutes, and check for leaks

at the connections. We recommend that

the fuel filter be replaced by an author-

ized HYUNDAI dealer.

The vapor hose and fuel filler cap should

be inspected at those intervals specified

in the maintenance schedule. Make sure

that a new vapor hose or fuel filler cap is

correctly replaced.

Vacuum crankcase ventilation

hoses (if equipped)

Drive belts

Inspect all drive belts for evidence of cuts,

cracks, excessive wear or oil saturation

and replace if necessary. Drive belts

should be checked periodically for proper

tension and adjusted as necessary.

Inspect the surface of hoses for evidence

of heat and/or mechanical damage. Hard

and brittle rubber, cracking, tears, cuts,

abrasions, and excessive swelling indi-

cate deterioration. Particular attention

should be paid to examine those hose

surfaces nearest to high heat sources,

such as the exhaust manifold.

Inspect the hose routing to assure that

the hoses do not come in contact with

any heat source, sharp edges or moving

component which might cause heat dam-

age or mechanical wear. Inspect all hose

connections, such as clamps and cou-

plings, to make sure they are secure, and

that no leaks are present. Hoses should

be replaced immediately if there is any

evidence of deterioration or damage.

Fuel lines, fuel hoses and con-

nections

Check the fuel lines, fuel hoses and con-

nections for leakage and damage. We

recommend that the fuel lines, fuel hoses

and connectionsr be replaced by an

authorized HYUNDAI dealer.

7 19

Maintenance

Air cleaner filter

Coolant

Brake hoses and lines

When replacing the air cleaner filter, we

recommend that you use HYUNDAI gen-

uine parts.

The coolant should be changed at the

intervals specified in the maintenance

schedule.

Visually check for proper installation,

chafing, cracks, deterioration and any

leakage. Replace any deteriorated or

damaged parts immediately.

Spark plugs

Make sure to install new spark plugs of

the correct heat range.

Manual transaxle fluid

(if equipped)

Inspect the manual transaxle fluid

according to the maintenance schedule.

Brake fluid

Check the brake fluid level in the brake

fluid reservoir. The level should be

between “MIN” and “MAX” marks on the

side of the reservoir. Use only hydraulic

brake fluid conforming to DOT 3 or DOT

4 specification.

Valve clearance (if equipped)

Automatic transaxle fluid

(if equipped)

Inspect the automatic transaxle fluid

according to the maintenance schedule.

Inspect for excessive valve noise and/or

engine vibration and adjust if necessary.

We recommend that the system be serv-

iced by an authorized HYUNDAI dealer.

Parking brake

Inspect the parking brake system includ-

ing the parking brake lever and cables.

Cooling system

Check the cooling system components,

such as the radiator, coolant reservoir,

hoses and connections for leakage and

damage. Replace any damaged parts.

7 20

Maintenance

Rear brake drums and linings

(if equipped)

Steering gear box, linkage &

boots/lower arm ball joint

Check the rear brake drums and linings

for scoring, burning, leaking fluid, broken

parts, and excessive wear.

With the vehicle stopped and engine off,

check for excessive free-play in the

steering wheel.

Check the linkage for bends or damage.

Check the dust boots and ball joints for

deterioration, cracks, or damage.

Replace any damaged parts.

Brake pads, calipers and rotors

Check the pads for excessive wear, discs

for run out and wear, and calipers for fluid

leakage.

Drive shafts and boots

Suspension mounting bolts

Check the drive shafts, boots and clamps

for cracks, deterioration, or damage.

Replace any damaged parts and, if nec-

essary, repack the grease.

Check the suspension connections for

looseness or damage. Retighten to the

specified torque.

Air conditioning refrigerant

(if equipped)

Check the air conditioning lines and con-

nections for leakage and damage.

7 21

Maintenance

ENGINE OIL

5. Pull the dipstick out again and check

the level. The level should be between

F and L.

CAUTION

Do not overfill the engine oil. It may

damage the engine.

OBA073002

OBA073003

If it is near or at L, add enough oil to bring

the level to F. Do not overfill.

Checking the engine oil level

1. Be sure the vehicle is on level ground.

2. Start the engine and allow it to reach

normal operating temperature.

3. Turn the engine off and wait for a few

minutes (about 5 minutes) for the oil to

return to the oil pan.

4. Pull the dipstick out, wipe it clean, and

re-insert it fully.

Use a funnel to help prevent oil from

being spilled on engine components.

Use only the specified engine oil. (Refer

to “Recommended lubricants and capac-

ities” in chapter 8.)

WARNING - Radiator hose

Be very careful not to touch the

radiator hose when checking or

adding the engine oil as it may be

hot enough to burn you.

7 22

Maintenance

ENGINE COOLANT

The high-pressure cooling system has a

reservoir filled with year round antifreeze

coolant. The reservoir is filled at the fac-

tory.

Check the antifreeze protection and

coolant level at least once a year, at the

beginning of the winter season, and

before traveling to a colder climate.

Changing the engine oil and filter

Checking the coolant level

We recommend that the engine oil and

filter be replaced by an authorized

HYUNDAI dealer.

WARNING

Removing radiator

cap

WARNING

Used engine oil may cause skin irri-

tation or cancer if left in contact

with the skin for prolonged periods

of time. Used engine oil contains

chemicals that have caused cancer

in laboratory animals. Always pro-

tect your skin by washing your

hands thoroughly with soap and

warm water as soon as possible

after handling used oil.

• Never attempt to remove the radi-

ator cap while the engine is oper-

ating or hot. Doing so might lead

to cooling system and engine

damage and could result in seri-

ous personal injury from escap-

ing hot coolant or steam.

• Turn the engine off and wait until

it cools down. Use extreme care

when removing the radiator cap.

Wrap a thick towel around it, and

turn it counterclockwise slowly to

the first stop. Step back while the

pressure is released from the

cooling system. When you are

sure all the pressure has been

released, press down on the cap,

using a thick towel, and continue

turning counterclockwise to

remove it.

(Continued)

7 23

Maintenance

Recommended engine coolant

• Use only soft (distilled) water in the

coolant mixture.

• The engine in your vehicle has alu-

minum engine parts and must be pro-

tected by an ethylene-glycol-based

coolant to prevent corrosion and freez-

ing.

(Continued)

• Even if the engine is not operat-

ing, do not remove the radiator

cap or the drain plug while the

engine and radiator are hot. Hot

coolant and steam may still blow

out under pressure, causing seri-

ous injury.

• DO NOT USE alcohol or methanol

coolant or mix them with the specified

coolant.

• Do not use a solution that contains

more than 60% antifreeze or less than

35% antifreeze, which would reduce

the effectiveness of the solution.

WARNING

OBA073004

The electric motor (cool-

ing fan) is controlled by

Check the condition and connections of

all cooling system hoses and heater

hoses. Replace any swollen or deterio-

rated hoses.

The coolant level should be filled

between F (MAX) and L (MIN) marks on

the side of the coolant reservoir when the

engine is cool.

If the coolant level is low, add enough

specified coolant to provide protection

against freezing and corrosion. Bring the

level to F (MAX), but do not overfill.

If frequent additions are required, we rec-

ommend that the system be inspected by

an authorized HYUNDAI dealer.

engine coolant tempera-

ture, refrigerant pres-

sure and vehicle speed.

It may sometimes operate even

when the engine is not running.

Use extreme caution when working

near the blades of the cooling fan

so that you are not injured by a

rotating fan blades. As the engine

coolant temperature decreases, the

electric motor will automatically

shut off.This is a normal condition.

For mixture percentage, refer to the fol-

lowing table.

Mixture Percentage

Ambient

(volume)

Temperature

Antifreeze

Water

65

-15°C (5°F)

-25°C (-13°F)

-35°C (-31°F)

-45°C (-49°F)

35

40

50

60

50

40

7 24

Maintenance

Changing the coolant

We recommend that the coolant be

replaced by an authorized HYUNDAI

dealer.

CAUTION

Put a thick cloth around the radiator

cap before refilling the coolant in

order to prevent the coolant from

overflowing into the engine parts

such as the generator.

OBA073005

WARNING - Coolant

• Do not use radiator coolant or

antifreeze in the washer fluid

reservoir.

WARNING

Radiator cap

• Radiator coolant can severely

obscure visibility when sprayed

on the windshield and may cause

loss of vehicle control or damage

to paint and body trim.

Do not remove the radiator cap

when the engine and radiator are

hot. Scalding hot coolant and

steam may blow out under pres-

sure causing serious injury.

7 25

Maintenance

BRAKES/CLUTCH(IF EQUIPPED) FLUID

■ Left-hand drive

Before removing the reservoir cap and

adding brake/clutch fluid, clean the area

around the reservoir cap thoroughly to

prevent brake/clutch fluid contamination.

If the level is low, add fluid to the MAX

level. The level will fall with accumulated

mileage. This is a normal condition asso-

ciated with the wear of the brake linings.

If the fluid level is excessively low, we

recommend that the system be checked

by an authorized HYUNDAI dealer.

WARNING - Brake/clutch

fluid

When changing and adding

brake/clutch fluid, handle it careful-

ly. Do not let it come in contact with

your eyes. If brake/clutch fluid

come in contact with your eyes,

immediately flush them with a large

quantity of fresh tap water. Have

your eyes examined by a doctor as

soon as possible.

OBA073006

■ Right-hand drive

Use only the specified brake/clutch fluid.

(Refer to “Recommended lubricants and

capacities” in chapter 8.)

CAUTION

Do not allow brake/clutch fluid to

contact the vehicle's body paint, as

Never mix different types of fluid.

paint

damage

will

result.

Brake/clutch fluid, which has been

exposed to open air for an extended

time should never be used as its

quality cannot be guaranteed. It

should be properly disposed. Don't

put in the wrong kind of fluid. A few

drops of mineral-based oil, such as

engine oil, in your brake/clutch sys-

tem can damage the system parts.

OBA073006R

WARNING - Loss of brake

fluid

In the event the brake system

requires frequent additions of fluid,

we recommend that the system be

inspected by an authorized

HYUNDAI dealer.

Checking the brake/clutch fluid

level

Check the fluid level in the reservoir peri-

odically. The fluid level should be

between MAX and MIN marks on the

side of the reservoir.

7 26

Maintenance

AUTOMATIC TRANSAXLE FLUID (IF EQUIPPED)

WARNING - Transaxle fluid

The transaxle fluid level should be

checked when the engine is at nor-

mal operating temperature. This

means that the engine, radiator,

radiator hose and exhaust system

etc., are very hot. Exercise great

care not to burn yourself during

this procedure.

OBA073007

OHD076045N

3. Confirm that the fluid level is in “HOT”

range on the level gauge. If the fluid

level is lower, add the specified fluid in

the fill hole. If the fluid level is higher,

drain the fluid from the drain hole.

4. If the fluid level is checked in cold con-

dition (fluid temperature 20~30°C

(68~86°F) add the fluid to “C” (COLD)

line and then recheck the fluid level

according to the above step 2.

Checking the automatic transaxle

fluid level

The automatic transaxle fluid level

should be checked regularly.

Keep the vehicle on the level ground with

the parking brake applied and check the

fluid level according to the following pro-

cedure.

1. Place the shift lever in N (Neutral)

position and confirm the engine is run-

ning at normal idle speed.

2. After the transaxle is warmed up suffi-

ciently (fluid temperature 70~80°C

(158~176°F), for example by 10 min-

utes usual driving, move the shift lever

through all the positions then place the

shift lever in “N (Neutral) or P (Park)”

position.

7 27

Maintenance

Changing the automatic transaxle

fluid

We recommend that the system be

replaced by an authorized HYUNDAI

dealer.

✽

NOTICE

CAUTION

A new automatic transaxle fluid should

be red. The red dye is added so the

assembly plant can identify it as auto-

matic transaxle fluid and distinguish it

from engine oil or antifreeze. The red

dye, which is not an indicator of fluid

quality, is not permanent. As the vehicle

is driven, the automatic transaxle fluid

will begin to look darker. The color may

eventually appear light brown.

Therefore, we recommend that the sys-

tem be replaced by an authorized

HYUNDAI dealer according to the

Scheduled Maintenance at the begin-

ning of this chapter.

• Low fluid level causes transaxle

shift slippage. Overfilling can

cause foaming, loss of fluid and

transaxle malfunction.

• The use of a non-specified fluid

could result in transaxle malfunc-

tion and failure.

WARNING - Parking brake

To avoid sudden movement of the

vehicle, apply the parking brake

and depress the brake pedal before

moving the shift lever.

Use only the specified automatic

transaxle fluid. (Refer to “Recommended

lubricants and capacities” in chapter 8.)

✽

NOTICE

“C” (COLD) range is for reference only

and should NOT be used to determine

the transaxle fluid level.

7 28

Maintenance

WASHER FLUID

PARKING BRAKE

■ Left-hand drive

WARNING - Coolant

• Do not use radiator coolant or

antifreeze in the washer fluid

reservoir.

• Radiator coolant can severely

obscure visibility when sprayed

on the windshield and may cause

loss of vehicle control or damage

to paint and body trim.

• Windshield Washer fluid agents

contain some amounts of alcohol

and can be flammable under cer-

tain circumstances. Do not allow

sparks or flame to contact the

washer fluid or the washer fluid

reservoir. Damage to the vehicle

or occupants could occur.

• Windshield washer fluid is poi-

sonous to humans and animals.

Do not drink and avoid contact-

ing windshield washer fluid.

Serious injury or death could

occur.

OBA053006

■ Right-hand drive

OBA073008

Checking the washer fluid level

The reservoir is translucent so that you

can check the level with a quick visual

inspection.

Check the fluid level in the washer fluid

reservoir and add fluid if necessary. Plain

water may be used if washer fluid is not

available. However, use washer solvent

with antifreeze characteristics in cold cli-

mates to prevent freezing.

OBA053006R

Checking the parking brake

Check the stroke of the parking brake by

counting the number of “clicks’’ heard

while fully applying it from the released

position. Also, the parking brake alone

should securely hold the vehicle on a fair-

ly steep grade.

7 29

Maintenance

AIR CLEANER

Filter replacement

It must be replaced when necessary, and

should not be cleaned and reused.

If the stroke is more or less than speci-

fied, we recommend that the system be

serviced by an authorized HYUNDAI

dealer.

Stroke : 6~8 clicks at a force of 20kg

(44lbs, 196N).

OBA073025

OBA073026

1.Remove the intake hose clamp.

2.Loosen the air cleaner cover attaching

clips and open the cover.

7 30

Maintenance

Replace the filter according to the

Maintenance Schedule.

CAUTION

• Do not drive with the air cleaner

removed; this will result in exces-

sive engine wear.

• When removing the air cleaner fil-

ter, be careful that dust or dirt

does not enter the air intake, or

damage may result.

If the vehicle is operated in extremely

dusty or sandy areas, replace the ele-

ment more often than the usual recom-

mended

intervals.

(Refer

to

“Maintenance under severe usage condi-

tions” in this chapter.)

• We recommend that you use

parts for replacement from an

authorized HYUNDAI dealer. Use

of improper parts could damage

the air flow sensor or turbo charg-

er.

OBA073027

3.Replace the air cleaner filter.

4.Reassemble in the reverse order of

removal.

7 31

Maintenance

CLIMATE CONTROL AIR FILTER (IF EQUIPPED)

■ Left-hand drive

Filter inspection

The climate control air filter should be

replaced according to the Maintenance

Schedule. If the vehicle is operated in

severely air-polluted cities or on dusty

rough roads for a long period, it should

be inspected more frequently and

replaced earlier. When you replace the

climate control air filter, replace it per-

forming the following procedure, and be

careful to avoid damaging other compo-

OBA073032

OBA073029

nents.

■ Right-hand drive

OBA073032R

OBA073029R

2.Remove the climate control air filter

cover.

Filter replacement

1.With the glove box opened, push in

both sides of the glove box as shown.

This will ensure that the glove box

stopper pins will get released from its

holding location allowing the glove box

to hang.

7 32

Maintenance

■ Left-hand drive

OBA073030

■ Right-hand drive

OBA073031

4.Replace the climate control air filter.

5.Reassemble in the reverse order of

disassembly.

✽

NOTICE

When replacing the climate control air

filter install it properly. Otherwise, the

system may produce noise and the effec-

tiveness of the filter may be reduced.

OBA073030R-1

3. Pull out the air filter

7 33

Maintenance

WIPER BLADES

Contamination of either the windshield or

the wiper blades with foreign matter can

reduce the effectiveness of the wind-

shield wipers. Common sources of con-

tamination are insects, tree sap, and hot

wax treatments used by some commer-

cial car washes. If the blades are not wip-

ing properly, clean both the window and

the blades with a good cleaner or mild

detergent, and rinse thoroughly with

clean water.

Blade replacement

When the wipers no longer clean ade-

quately, the blades may be worn or

cracked, and require replacement.

CAUTION

To prevent damage to the wiper

arms or other components, do not

attempt to move the wipers manual-

ly.

1JBA5122

CAUTION

The use of a non-specified wiper

blade could result in wiper malfunc-

tion and failure.

Blade inspection

To prevent damage to the wiper

blades, do not use gasoline,

kerosene, paint thinner, or other

solvents on or near them.

✽

NOTICE

Commercial hot waxes applied by auto-

matic car washes have been known to

make the windshield difficult to clean.

7 34

Maintenance

1JBA7037

1LDA5023

OHM078059

Type B

1.Raise the wiper arm.

Front windshield wiper blade

Type A

1.Raise the wiper arm and rotate the

wiper blade assembly to expose the

plastic locking clip.

CAUTION

Do not allow the wiper arm to fall

against the windshield, since it may

chip or crack the windshield.

CAUTION

Do not allow the wiper arm to fall

against the windshield, since it may

chip or crack the windshield.

1JBA7038

2.Compress the clip (1) and slide the

blade assembly downward (2).

3.Lift it off the arm.

4.Install a blade assembly in the reverse

order of removal.

5.Return the wiper arm on the wind-

shield.

7 35

Maintenance

OHM078060

OHM078061

OPA077017

2.Lift up the wiper blade clip (1). Then

pull down the blade assembly (2) and

remove it.

3.Install a new blade assembly in the

reverse order of removal.

4.Return the wiper arm on the wind-

shield.

Rear window wiper blade

(if equipped)

1.Raise the wiper arm and pull out the

wiper blade assembly.

2.Slightly rotate the wiper blade assem-

bly (1) and pull it out.

7 36

Maintenance

OPA077018

3.Install a new blade assembly by insert-

ing the center part into the slot on the

wiper arm until it clicks into place.

4.Make sure the blade assembly is

installed firmly by trying to pull it slight-

ly.

To prevent damage to the wiper arms or

other components, we recommend that

the wiper blade be replaced by an

authorized HYUNDAI dealer.

7 37

Maintenance

BATTERY

(Continued)

WARNING

If acid gets into your eyes, flush

your eyes with clean water for at

least 15 minutes and get immediate

medical attention. If acid gets on

your skin, thoroughly wash the

area. If you feel pain or a burning

sensation, get medical attention

immediately.

• When lifting a plastic-cased bat-

tery, excessive pressure on the

case may cause battery acid to

leak. Lift with a battery carrier or

with your hands on opposite cor-

ners.

• Do not attempt to jump start your

vehicle if your battery is frozen.

• NEVER attempt to recharge the

battery when the vehicle’s battery

cables are connected to the bat-

tery.

To prevent SERIOUS INJURY or

DEATH to you or bystanders,

always follow these precautions

when working near or handling the

battery:

Always read and follow

instructions carefully when

handling a battery.

Wear

eye

protection

designed to protect the

eyes from acid splashes.

OBA073009

For best battery service

• Keep the battery securely mounted.

• Keep the battery top clean and dry.

• Keep the terminals and connections

clean, tight, and coated with petroleum

jelly or terminal grease.

• Rinse any spilled electrolyte from the

battery immediately with a solution of

water and baking soda.

Keep all flames, sparks, or

smoking materials away

from the battery.

Hydrogen is always present

in battery cells, is highly

combustible, and may

explode if ignited.

Keep batteries out of reach

of children.

• The electrical ignition system

works with high voltage. NEVER

touch these components with the

engine running or when the igni-

tion switch is in the ON position.

• If the vehicle is not going to be used for

an extended time, disconnect the bat-

tery cables.

Batteries contain sulfuric

acid which is highly corro-

sive. Do not allow acid to

contact your eyes, skin or

clothing.

(Continued)

7 38

Maintenance

■ Example

Battery recharging

CAUTION

Your vehicle has a maintenance-free,

calcium-based battery.

To prevent damage to your vehicle:

• Only use a 12-volt power supply

(battery or jumper system) to

jump start your vehicle.

• Do not attempt to jump start your

vehicle by push-starting.

• If the battery becomes discharged in a

short time (because, for example, the

headlights or interior lights were left on

while the vehicle was not in use),

recharge it by slow charging (trickle)

for 10 hours.

• If the battery gradually discharges

because of high electric load while the

vehicle is being used, recharge it at 20-

30A for two hours.

✽

NOTICE

An inappropriately disposed

OJD072039

battery can be harmful to the

environment and human health.

Dispose the battery according

to your local law(s) or regula-

tion.

❈ The actual battery label in the vehicle

may differ from the illustration.

Battery capacity label

1.CMF65L-BCI : HYUNDAI model name

of battery

2.12V : Nominal voltage

3.60Ah(20HR) : Nominal capacity

(in Ampere hours)

4.92RC :Nominal reserve capacity

(in min.)

5.550CCA : Cold-test current

(in amperes by SAE)

6.440A : Cold-test current

(in amperes by EN)

7 39

Maintenance

Reset items

(Continued)

WARNING - Recharging

Items should be reset after the battery

has been discharged or the battery has

been disconnected.

• Auto up/down window (See chapter 4)

• Climate control system

(See chapter 4)

• Before performing maintenance

or recharging the battery, turn off

all accessories and stop the

engine.

• The negative battery cable must

be removed first and installed

last when the battery is discon-

nected.

battery

When recharging the battery,

observe the following precautions:

• The battery must be removed

from the vehicle and placed in an

area with good ventilation.

• Audio (See chapter 4)

• Do not allow cigarettes, sparks,

or flame near the battery.

• Watch the battery during charging,

and stop or reduce the charging

rate if the battery cells begin

gassing (boiling) violently or if the

temperature of the electrolyte of

any cell exceeds 49°C (120°F).

• Wear eye protection when check-

ing the battery during charging.

• Disconnect the battery charger in

the following order.

1. Turn off the battery charger main

switch.

2. Unhook the negative clamp from

the negative battery terminal.

3. Unhook the positive clamp from

the positive battery terminal.

(Continued)

7 40

Maintenance

TIRES AND WHEELS

Tire care

For proper maintenance, safety, and

maximum fuel economy, you must

always maintain recommended tire

inflation pressures and stay within

the load limits and weight distribution

recommended for your vehicle.

WARNING - Tire underin-

flation

Severe underinflation (70 kPa

(10 psi) or more) can lead to

severe heat build-up, causing

blowouts, tread separation and

other tire failures that can result

in the loss of vehicle control

leading to severe injury or

death. This risk is much higher

on hot days and when driving

for long periods at high speeds.

Recommended cold tire inflation

pressures

All tire pressures (including the

spare) should be checked when the

tires are cold. “Cold Tires” means the

vehicle has not been driven for at

least three hours or driven less than

1.6 km (one mile).

OBA073010

All specifications (sizes and pres-

sures) can be found on a label

attached to the vehicle.

Recommended pressures must be

maintained for the best ride, top vehi-

cle handling, and minimum tire wear.

For recommended inflation pressure

refer to “Tire and wheels” in chapter 8.

7 41

Maintenance

CAUTION

CAUTION - Tire pressure

Always observe the following:

• Check tire pressure when the

tires are cold. (After vehicle

has been parked for at least

three hours or hasn't been

driven more than 1.6 km (one

mile) since startup.)

• Check the pressure of your

spare tire each time you check

the pressure of other tires.

• Never overload your vehicle.

Be careful not to overload a

vehicle luggage rack if your

vehicle is equipped with one.

• Underinflation also results in

excessive wear, poor handling

and reduced fuel economy.

Wheel deformation also is

possible. Keep your tire pres-

sures at the proper levels. If a

tire frequently needs refilling,

we recommend that the sys-

tem be checked by an author-

ized HYUNDAI dealer.

• Warm tires normally exceed

recommended cold tire pres-

sures by 28 to 41 kPa (4 to 6

psi). Do not release air from

warm tires to adjust the pres-

sure or the tires will be under-

inflated.

• Be sure to reinstall the tire

inflation valve caps. Without

the valve cap, dirt or moisture

could get into the valve core

and cause air leakage. If a

valve cap is missing, install a

new one as soon as possible.

• Overinflation produces

a

harsh ride, excessive wear at

the center of the tire tread, and

a greater possibility of dam-

age from road hazards.

• Worn, old tires can cause acci-

dents. If your tread is badly

worn, or if your tires have

been damaged, replace them.

WARNING - Tire inflation

Overinflation or underinflation

can reduce tire life, adversely

affect vehicle handling, and

lead to sudden tire failure. This

could result in loss of vehicle

control and potential injury.

7 42

Maintenance

Checking tire inflation pressure

Check your tires once a month or

more.

Also, check the tire pressure of the

spare tire.

Remove the valve cap from the tire

valve stem. Press the tire gage firm-

ly onto the valve to get a pressure

measurement. If the cold tire inflation

pressure matches the recommended

pressure on the tire and loading

information label, no further adjust-

ment is necessary. If the pressure is

low, add air until you reach the rec-

ommended amount.

If you overfill the tire, release air by

pushing on the metal stem in the

center of the tire valve. Recheck the

tire pressure with the tire gage. Be

sure to put the valve caps back on

the valve stems. They help prevent

leaks by keeping out dirt and mois-

ture.

WARNING

• Inspect your tires frequently

for proper inflation as well as

wear and damage. Always use

a tire pressure gauge.

• Tires with too much or too little

pressure wear unevenly caus-

ing poor handling, loss of vehi-

cle control, and sudden tire

failure leading to accidents,

injuries, and even death. The

recommended cold tire pres-

sure for your vehicle can be

found in this manual and on

the tire label located on the dri-

ver's side center pillar.

How to check

Use a good quality gage to check tire

pressure.You can not tell if your tires

are properly inflated simply by look-

ing at them. Radial tires may look

properly inflated even when they're

underinflated.

Check the tire's inflation pressure

when the tires are cold. - "Cold"

means your vehicle has been sitting

for at least three hours or driven no

more than 1.6 km (1 mile).

• Worn tires can cause acci-

dents. Replace tires that are

worn, show uneven wear, or

are damaged.

• Remember to check the pres-

sure of your spare tire.

HYUNDAI recommends that

you check the spare every

time you check the pressure

of the other tires on your vehi-

cle.

7 43

Maintenance

With a full-size spare tire (if equipped)

Tire rotation

WARNING

To equalize tread wear, it is recom-

mended that the tires be rotated

every 12,000 km (7,500 miles) or

sooner if irregular wear develops.

During rotation, check the tires for

correct balance.

When rotating tires, check for uneven

wear and damage. Abnormal wear is

usually caused by incorrect tire pres-

sure, improper wheel alignment, out-

of-balance wheels, severe braking or

severe cornering. Look for bumps or

bulges in the tread or side of tire.

Replace the tire if you find either of

these conditions. Replace the tire if

fabric or cord is visible. After rotation,

be sure to bring the front and rear tire

pressures to specification and check

lug nut tightness.

• Do not use the compact spare

tire for tire rotation.

• Do not mix bias ply and radial

ply tires under any circum-

stances. This may cause

unusual handling characteris-

tics that could result in death,

severe injury, or property

damage.

S2BLA790

Directional tires (if equipped)

CBGQ0707A

Refer to “Tire and wheels” in chapter

8.

Disc brake pads should be inspected

for wear whenever tires are rotated.

✽

NOTICE

Rotate radial tires that have an

asymmetric tread pattern only from

front to rear and not from right to

left.

7 44

Maintenance

Wheel alignment and tire balance

Tread wear indicator

WARNING - Replacing

The wheels on your vehicle were

aligned and balanced carefully at the

factory to give you the longest tire life

and best overall performance.

In most cases, you will not need to

have your wheels aligned again.

However, if you notice unusual tire

wear or your vehicle pulling one way

or the other, the alignment may need

to be reset.

tires

To reduce the chance or serious

or fatal injuries from an acci-

dent caused by tire failure or

loss of vehicle control:

• Replace tires that are worn,

show uneven wear, or are

damaged. Worn tires can

cause loss of braking effec-

tiveness, steering control, and

traction.

• Do not drive your vehicle with

too little or too much pressure

in your tires. This can lead to

uneven wear and tire failure.

• When replacing tires, never

mix radial and bias-ply tires

on the same car. You must

replace all tires (including the

spare) if moving from radial to

bias-ply tires.

OEN076053

If you notice your vehicle vibrating

when driving on a smooth road, your

wheels may need to be rebalanced.

Tire replacement

If the tire is worn evenly, a tread wear

indicator will appear as a solid band

across the tread. This shows there is

less than 1.6 mm (1/16 inch) of tread

left on the tire. Replace the tire when

this happens.

Do not wait for the band to appear

across the entire tread before replac-

ing the tire.

CAUTION

Improper wheel weights can

damage your vehicle's alu-

minum wheels. Use only

approved wheel weights.

(Continued)

7 45

Maintenance

Wheel replacement

Tire traction

(Continued)

When replacing the metal wheels for Tire traction can be reduced if you

any reason, make sure the new drive on worn tires, tires that are

wheels are equivalent to the original improperly inflated or on slippery

factory units in diameter, rim width road surfaces. Tires should be

• Using tires and wheel other

than the recommended sizes

could cause unusual handling

characteristics and poor vehi-

cle control, resulting in a seri-

ous accident.

• Wheels that do not meet

HYUNDAI’s

may fit poorly and result in

damage to the vehicle or

unusual handling and poor

vehicle control.

• The ABS works by comparing

the speed of the wheels. Tire

size can affect wheel speed.

When replacing tires, all 4

tires must use the same size

originally supplied with the

vehicle. Using tires of a differ-

ent size can cause the ABS

(Anti-lock Brake System) and

ESC (Electronic Stability

Control) (if equipped) to work

irregularly.

and offset.

replaced when tread wear indicators

appear. Slow down whenever there

is rain, snow or ice on the road, to

reduce the possibility of losing con-

trol.

WARNING

A wheel that is not the correct

size may adversely affect wheel

and bearing life, braking and

stopping abilities, handling

characteristics, ground clear-

ance, body-to-tire clearance,

specifications

snow

chain

clearance,

speedometer and odometer cal-

ibration, headlight aim and

bumper height.

7 46

Maintenance

2. Tire size designation

Tire maintenance

1

A tire’s sidewall is marked with a tire

size designation. You will need this

information when selecting replace-

ment tires for your vehicle. The fol-

lowing explains what the letters and

numbers in the tire size designation

mean.

In addition to proper inflation, correct

wheel alignment helps to decrease

tire wear. If you find a tire is worn

unevenly, have your dealer check the

wheel alignment.

When you have new tires installed,

make sure they are balanced. This

will increase vehicle ride comfort and

tire life. Additionally, a tire should

always be rebalanced if it is removed

from the wheel.

5,6

7

4

2

3

Example tire size designation:

(These numbers are provided as an

example only; your tire size designa-

tor could vary depending on your

vehicle.)

1

I030B04JM

Tire sidewall labeling

165/60R14 64T

This information identifies and

describes the fundamental charac-

teristics of the tire and also provides

the tire identification number (TIN)

for safety standard certification. The

TIN can be used to identify the tire in

case of a recall.

165 - Tire width in millimeters.

60 - Aspect ratio. The tire’s chapter

height as a percentage of its

width.

R - Tire construction code (Radial).

14 - Rim diameter in inches.

64 - Load Index, a numerical code

associated with the maximum

load the tire can carry.

1. Manufacturer or brand name

Manufacturer or Brand name is

shown.

T - Speed Rating Symbol. See the

speed rating chart in this chapter

for additional information.

7 47

Maintenance

Wheel size designation

Tire speed ratings

3. Checking tire life (TIN :Tire

Identification Number)

Wheels are also marked with impor- The chart below lists many of the dif-

tant information that you need if you ferent speed ratings currently being

ever have to replace one. The follow- used for passenger car tire. The

ing explains what the letters and speed rating is part of the tire size

numbers in the wheel size designa- designation on the sidewall of the

Any tires that are over 6 years old,

based on the manufacturing date,

(including the spare tire) should be

replaced by new ones. You can find

the manufacturing date on the tire

sidewall (possibly on the inside of the

wheel), displaying the DOT Code.

The DOT Code is a series of num-

bers on a tire consisting of numbers

and English letters. The manufactur-

ing date is designated by the last four

digits (characters) of the DOT code.

tion mean.

tire. This symbol corresponds to that

tire's designed maximum safe oper-

ating speed.

Example wheel size designation:

5.0JX14

Speed

Rating

Maximum Speed

Symbol

5.0 - Rim width in inches.

J - Rim contour designation.

14 - Rim diameter in inches.

S

T

H

V

Z

180 km/h (112 mph)

190 km/h (118 mph)

DOT : XXXX XXXX OOOO

210 km/h (130 mph)

The front part of the DOT means a

plant code number, tire size and

tread pattern and the last four num-

bers indicate week and year manu-

factured.

240 km/h (149 mph)

Above 240 km/h (149 mph)

For example:

DOT XXXX XXXX 1613 represents

that the tire was produced in the 16th

week of 2013.

7 48

Maintenance

4. Tire ply composition and material

7. Uniform tire quality grading

WARNING - Tire age

The number of layers or plies of rub- Quality grades can be found where

ber-coated fabric are in the tire. Tire applicable on the tire sidewall

manufacturers also must indicate the between tread shoulder and maxi-

materials in the tire, which include mum section width.

Tires degrade over time, even

when they are not being used.

Regardless of the remaining

tread, we recommend that tires

generally be replaced after six

(6) years of normal service.

Heat caused by not climates or

frequent high loading condi-

tions can accelerate the aging

process. Failure to follow this

Warning can result in sudden

tire failure, which could lead to

a loss of control and an acci-

dent involving serious injury or

death.

steel, nylon, polyester, and others.

For example:

The letter "R" means radial ply con-

TREADWEAR 200

struction; the letter "D" means diago-

TRACTION AA

TEMPERATURE A

nal or bias ply construction; and the

letter "B" means belted-bias ply con-

struction.

Tread wear

5. Maximum permissible inflation

pressure

The tread wear grade is a compara-

tive rating based on the wear rate of

the tire when tested under controlled

conditions on a specified govern-

ment test course. For example, a tire

graded 150 would wear one-and-a-

half times (1½) as well on the gov-

ernment course as a tire graded 100.

The relative performance of tires

depends upon the actual conditions

of their use, however, and may

depart significantly from the norm

due to variations in driving habits,

service practices and differences in

road characteristics and climate.

This number is the greatest amount

of air pressure that should be put in

the tire. Do not exceed the maximum

permissible inflation pressure. Refer

to the Tire and Loading Information

label for recommended inflation

pressure.

6. Maximum load rating

This number indicates the maximum

load in kilograms and pounds that

can be carried by the tire. When

replacing the tires on the vehicle,

always use a tire that has the same

load rating as the factory installed

tire.

7 49

Maintenance

Temperature -A, B & C

These grades are molded on the

side-walls of passenger vehicle tires.

The tires available as standard or

optional equipment on your vehicles

may vary with respect to grade.

WARNING - Tire

temperature

The temperature grades are A (the

highest), B and C representing the

tire’s resistance to the generation of

heat and its ability to dissipate heat

when tested under controlled condi-

tions on a specified indoor laboratory

test wheel.

Sustained high temperature can

cause the material of the tire to

degenerate and reduce tire life, and

excessive temperature can lead to

sudden tire failure. Grades B and A

represent higher levels of perform-

ance on the laboratory test wheel

than the minimum required by law.

The temperature grade for this

tire is established for a tire that

is properly inflated and not

overloaded. Excessive speed,

underinflation, or excessive

loading, either separately or in

combination, can cause heat

build-up and possible sudden

tire failure. This can cause loss

of vehicle control and serious

injury or death.

Traction - AA, A, B & C

The traction grades, from highest to

lowest, are AA, A, B and C. Those

grades represent the tires ability to

stop on wet pavement as measured

under controlled conditions on spec-

ified government test surfaces of

asphalt and concrete. A tire marked

C may have poor traction perform-

ance.

WARNING

The traction grade assigned to

this tire is based on straight-

ahead braking traction tests,

and does not include accelera-

tion, cornering, hydroplaning,

or peak traction characteristics.

7 50

Maintenance

Low aspect ratio tire (if equipped)

CAUTION

Low aspect ratio tires, the aspect

ratio is lower than 50, are provided

for sporty looks.

Because the low aspect ratio tires

are optimized for handling and brak-

ing, it may be more uncomfortable to

ride in and there is more noise com-

pare with normal tires.

Because the sidewall of the low

aspect ratio tire is shorter than

the normal, the wheel and tire of

the low aspect ratio tire is easi-

er to be damaged. So, follow the

instructions below.

• It is not easy to recognize the

tire damage with your own

eyes. But if there is the slight-

est hint of tire damage, even

though you cannot see the tire

damage with your own eyes,

have the tire checked or

replaced because the tire

damage may cause air leak-

age from the tire.

- When driving on a rough road

or off road, drive cautiously

because tires and wheels may

be damaged. And after driving,

inspect tires and wheels.

- When passing over a pothole,

speed bump, manhole, or curb

stone, drive slowly so that the

tires and wheels are not dam-

aged.

• If the tire is damaged by driv-

ing on a rough road, off road,

pothole, manhole, or curb

stone, it will not be covered by

the warranty.

• You can find out the tire infor-

mation on the tire sidewall.

- If the tire is impacted, we rec-

ommend that you inspect the

tire condition or contact an

authorized HYUNDAI dealer.

- To prevent damage to the tire,

inspect the tire condition and

pressure every 3,000km.

7 51

Maintenance

FUSES

■ Blade type

A vehicle’s electrical system is protected

from electrical overload damage by

fuses.

WARNING - Fuse replace-

ment

• Never replace a fuse with any-

thing but another fuse of the

same rating.

• A higher capacity fuse could

cause damage and possibly a

fire.

• Never install a wire or aluminum

foil instead of the proper fuse -

even as a temporary repair. It may

cause extensive wiring damage

and a possible fire.

This vehicle has 2 fuse panels, one locat-

ed in the driver’s side panel bolster, the

other in the engine compartment near

the battery.

If any of your vehicle’s lights, acces-

sories, or controls do not work, check the

appropriate circuit fuse. If a fuse has

blown, the element inside the fuse will

melt.

If the electrical system does not work,

first check the driver’s side fuse panel.

Always replace a blown fuse with one of

the same rating.

Blown

Normal

■ Cartridge type

Normal

Blown

■ Multi fuse

CAUTION

If the replacement fuse blows, this indi-

cates an electrical problem. Avoid using

the system involved and we recommend

that you consult an authorized HYUNDAI

dealer.

Do not use a screwdriver or any

other metal object to remove fuses

because it may cause a short circuit

and damage the system.

✽

NOTICE

Normal

Blown

OJC070046D

Three kinds of fuses are used: blade

type for lower amperage rating, car-

tridge type, and fusible link for higher

amperage ratings.

7 52

Maintenance

■ Left-hand drive - Type A

■ Left-hand drive - Type B

■ Right-hand drive - Type A

■ Right-hand drive - Type B

OBA073013

3.Pull the suspected fuse straight out.

Use the removal tool provided in the

engine compartment fuse panel.

4.Remove and check the suspected

fuse; replace it if it is blown.

5.Push in a new fuse of the same rating,

and make sure it fits tightly in the clips.

If it fits loosely, we recommend that you

consult an authorized HYUNDAI dealer.

OBA073011/OBA073011IN/OBA073011L/OBA073011R

Instrument panel fuse replacement

1.Turn the ignition switch and all other switches off.

2.Open the fuse panel cover.

7 53

Maintenance

■ Left-hand drive

In an emergency, if you do not have a

spare, use a fuse of the same rating from

a circuit you may not need for operating

the vehicle, such as the cigarette lighter

fuse.

CAUTION

• Always place the fuse switch in

the ON position while driving the

vehicle. If the switch is in the OFF

position, a warning will appear on

the instrument cluster. (Refer to

“Instrument Cluster”in chapter 4.)

• The theft alarm system will not

activate with the fuse switch in the

OFF position.

If the headlights or other electrical com-

ponents do not work and the fuses are

OK, check the fuse block in the engine

compartment. If a fuse is blown, it must

be replaced.

OBA073012

■ Right-hand drive

OBA073012IN

Fuse switch (for Type A)

Always, put the fuse switch at the ON

position.

If you move the switch to the OFF posi-

tion, some items must be reset and

remote key or smart key may not work

properly.

7 54

Maintenance

■ Left-hand drive

1.Turn off the engine.

2.Turn off the headlights and tail lights.

3.Open the driver’s side panel cover and

pull up the memory fuse.

✽

NOTICE

• If the memory fuse is pulled up from

the fuse panel, the warning chime,

audio, clock and interior lamps, etc.,

will not operate. Some items must be

reset after replacement. Refer to

“Battery” in this chapter.

OBA073012L

■ Right-hand drive

OBA073014

• Even though the memory fuse is

pulled up, the battery can still be dis-

charged by operation of the head-

lights or other electrical devices.

Engine compartment panel fuse

replacement

1.Turn the ignition switch and all other

switches off.

2.Remove the fuse box cover by press-

ing the tap and pulling the cover up.

3.Remove and check the suspected

fuse; replace it if it is blown. To remove

or insert the fuse, use the fuse puller in

the engine compartment fuse panel.

4.Push in a new fuse of the same rating,

and make sure it fits tightly in the clips.

OBA073012R

Memory fuse (for Type B)

Your vehicle is equipped with the memo-

ry fuse to prevent battery discharge if

your vehicle is parked without being

operated for prolonged periods. Use the

following procedures before parking the

vehicle for prolonged periods.

If it fits loosely, we recommend that you

consult an authorized HYUNDAI dealer.

7 55

Maintenance

CAUTION

After checking the fuse box in the

engine compartment, securely

install the fuse box cover. If not,

electrical failures may occur from

water leaking in.

OBA073015

Main fuse (multi fuse)

If the main fuse is blown, it must be

removed as follows:

1.Disconnect the negative battery cable.

2.Remove the nuts shown in the picture

above.

3.Replace the fuse with a new one of the

same rating.

4.Reinstall in the reverse order of

removal.

✽

NOTICE

If the main fuse is blown, we recom-

mend that you consult an authorized

HYUNDAI dealer.

7 56

Maintenance

■ Left-hand drive

■ Type A

OBA073016

■ Right-hand drive

OBA073016IN

OBA073041R

Fuse/relay panel description

Instrument panel fuse panel

Inside the fuse/relay panel covers, you

can find the fuse/relay label describing

the \fuse/relay name and capacity.

✽

NOTICE

Not all fuse panel descriptions in this manual may be applicable to your vehicle. It

is accurate at the time of printing. When you inspect the fuse panel in your vehicle,

refer to the fuse panel label.

7 57

Maintenance

Instrument panel fuse panel

Fuse Name

Symbol

Fuse rating

Circuit Protected

RR HTD

30A

RR HTD Relay

A/CON 1

7.5A

25A

15A

25A

10A

7.5A

25A

10A

15A

A/C Control Module (Auto)

Driver Safety Power Window Module

SAFETY POWER

WINDOW

STOP

LAMP

STOP LAMP

P/WDW LH

P/WDW RH

PDM 2

Stop Signal Electronic Module, Data Link Connector

Power Window Main Switch, Driver Safety Power Window Module (LHD), Passenger Power

Window Switch (RHD)

Power Window Main Switch, Driver Safety Power Window Module (RHD), Passenger

Power Window Switch (LHD)

2

Smart Key Control Module, Start/Stop Button Switch

PCB Fuse & Relay Box (Vacuum Pump Relay)

S

SENSOR

START

B/Alarm Relay, PCB Fuse & Relay Box (Start Relay), PCM, Smart Key Control Module,

Transaxle Range Switch

1

PDM 1

Smart Key Control Module

BRAKE SWITCH

TCU

Smart Key Control Module, Stop Lamp Switch

A/T : Transaxle Range Switch, Pulse Generator 'A'/'B'

M/T : Vehicle Speed Sensor, PCB Fuse & Relay Box (F34)

T

7 58

Maintenance

Fuse Name

Symbol

Fuse rating

Circuit Protected

BLOWER

7.5A

PCM, A/C Control Module, Electronic A/C Compressor, Blower Switch, Blower Resistor

Door Lock/Unlock Relay, T/Gate Unlock Relay, Crash Door Unlock Unit

PCM, A/C Control Module, Driver/Passenger Power Outside Mirror

DR LOCK

HTD MIRR

MODULE 2

WIPER

20A

10A

25A

10A

20A

Stop Lamp Switch, Crash Pad Switch, Rear Parking Assist, Rear Parking Assist Sensor

(Center) LH/RHSensor LH/RH

²MODULE

MEMORY

Front Wiper Motor, Multifunction Switch

Data Link Connector, Digital Clock, Instrument Cluster, BCM, Tire Pressure Motoring

Module, A/C Control Module, Crash Door Unlock Unit, Audio

MEMORY

INTERIOR LAMP

MODULE 3

ECU

Luggage Lamp, Room Lamp

³MODULE

E/R Junction Box (Multipurpose Check Connector), A/C Control Module

PCM, Smart Key Control Module, Alternator (G3LA/G4LA)

PCB Fuse & Relay Box (Blower Relay), A/C Control Module

Auido

E

A/CON 2

MULTI

MEDIA

MULTI MEDIA

²POWER

OUTLET

POWER

OUTLET 2

Rear Power Outlet

7 59

Maintenance

Fuse Name

Symbol

Fuse rating

Circuit Protected

CLUSTER

10A

Instrument Cluster

ABS

7.5A

10A

15A

20A

10A

7.5A

10A

ESP Control Module

-

⁵MODULE

MODULE 5

WIPER RR

Rear Wiper Motor, Multifunction Switch

¹POWER

OUTLET

POWER

OUTLET 1

Power Outlet

A/BAG

MDPS

SRS Control Module

MDPS Unit

⁴MODULE

¹MODULE

MODULE 4

ACC

BCM, Smart Key Control Module

BCM, Smart Key Control Module, Digital Clock, Auido, Power Outside Mirror Switch

A/BAG IND

MODULE 1

Instrument Cluster

BCM, SBR Indicator

7 60

Maintenance

■ Left-hand drive

■ Type B

OBA073016

■ Right-hand drive

OBA073016IN

OBA073039R

Instrument panel fuse panel

✽

NOTICE

Inside the fuse/relay panel covers, you

can find the fuse/relay label describing

the \fuse/relay name and capacity.

Not all fuse panel descriptions in this manual may be applicable to your vehicle. It

is accurate at the time of printing. When you inspect the fuse panel in your vehicle,

refer to the fuse panel label.

7 61

Maintenance

Instrument panel fuse panel

Fuse Name

Symbol

Fuse rating

Circuit Protected

ROOM LAMP

10A

Luggage Lamp, Room Lamp

Auido

AUDIO

RR HTD

A/CON 1

20A

30A

7.5A

25A

15A

25A

10A

7.5A

10A

15A

RR HTD Relay

A/C Control Module (Auto)

Driver Safety Power Window Module

SAFETY POWER

WINDOW

STOP

LAMP

STOP LAMP

P/WDW LH

P/WDW RH

SENSOR

Stop Signal Electronic Module, Data Link Connector

Power Window Main Switch, Driver Safety Power Window Module (LHD), Passenger Power

Window Switch (RHD)

Power Window Main Switch, Driver Safety Power Window Module (RHD), Passenger

Power Window Switch (LHD)

S

PCB Fuse & Relay Box (Vacuum Pump Relay)

B/Alarm Relay, PCB Fuse & Relay Box (Start Relay), PCM, Smart Key Control Module,

Transaxle Range Switch

START

BRAKE SWITCH

TCU

Smart Key Control Module, Stop Lamp Switch

A/T : Transaxle Range Switch, Pulse Generator 'A'/'B'

M/T : Vehicle Speed Sensor, PCB Fuse & Relay Box (F34)

T

7 62

Maintenance

Fuse Name

Symbol

Fuse rating

Circuit Protected

BLOWER

7.5A

PCM, A/C Control Module, Electronic A/C Compressor, Blower Switch, Blower Resistor

Door Lock/Unlock Relay, T/Gate Unlock Relay, Crash Door Unlock Unit

PCM, A/C Control Module, Driver/Passenger Power Outside Mirror

DR LOCK

HTD MIRR

MODULE 2

WIPER

20A

10A

25A

10A

20A

10A

7.5A

10A

Stop Lamp Switch, Crash Pad Switch, Rear Parking Assist, Rear Parking Assist Sensor

(Center) LH/RHSensor LH/RH

²MODULE

Front Wiper Motor, Multifunction Switch

³MODULE

MODULE 3

ECU

E/R Junction Box (Multipurpose Check Connector), A/C Control Module

E

PCM, Smart Key Control Module, Alternator (G3LA/G4LA)

A/CON 2

PCB Fuse & Relay Box (Blower Relay), A/C Control Module

²POWER

OUTLET

POWER

OUTLET 2

Rear Power Outlet

Instrument Cluster

ESP Control Module

-

CLUSTER

ABS

⁵MODULE

MODULE 5

7 63

Maintenance

Fuse Name

Symbol

Fuse rating

Circuit Protected

Rear Wiper Motor, Multifunction Switch

WIPER RR

15A

¹POWER

OUTLET

POWER

OUTLET 1

20A

10A

7.5A

10A

Power Outlet

A/BAG

MDPS

SRS Control Module

MDPS Unit

ACC

BCM, Smart Key Control Module, Digital Clock, Auido, Power Outside Mirror Switch

Instrument Cluster

A/BAG IND

T/SIG

Side Repeater Lamp (LH/RH), Rear Combination Lamp (LH/RH)

7 64

Maintenance

OBA073014

Engine compartment fuse panel

Inside the fuse/relay panel covers, you

can find the fuse/relay label describing

fuse/relay name and capacity.

✽

NOTICE

Not all fuse panel descriptions in this

manual may be applicable to your vehi-

cle. It is accurate at the time of printing.

When you inspect the fuse panel in your

vehicle, refer to the fuse panel label.

OIA073033

7 65

Maintenance

Engine compartment main fuse panel

Fuse Name

Symbol

Fuse rating

Circuit Protected

MDPS

80A

MDPS Unit

MULTI

FUSE

ALT

B+4

125A (150A) Alternator, Fuse - F3 / F4 / F6, PCB Fuse & Relay Box

4

50A

30A

50A

40A

50A

40A

7.5A

40A

30A

Smart Junction Box (Fuse : F1 / F2)

2

ESP 2

ESP 1

B+1

ESP Control Module, Multipurpose Check Connector

ESP Control Module

1

3

2

Smart Junction Box (T/Sig Sound Relay, Fuse : F10, ARISU-LT1, IPS 3)

Smart Junction Box (Power Window Relay, Fuse : F4, ARISU-LT2, IPS 5)

B+3

FUSE

Smart Junction Box (Fuse : F5 / F9 / F13 / F14 / F17, Leak Current Autocut Device

Fuse : F23 / F24 / F29)

B+2

W/O Button Start : Ignition Switch

With Button Start : PDM Relay Box (IG1 / ACC Relay)

IG1

FRT WIPER

BLOWER

ECU1

PCM, Front Wiper Motor, Multifunction Switch

Blower Relay

E1

Engine Control Relay, Fuse : F25 / F26

7 66

Maintenance

Fuse Name

Symbol

Fuse rating

Circuit Protected

F/PUMP

15A

F/Pump 1 Relay

HORN

A/CON

10A

20A

Horn Relay, B/Alarm Horn Relay

A/CON Relay

VACUUM

PUMP

VACUUM

PUMP

Vacuum Pump Relay

HEADLAMP

DIPPED

BEAM

15A

Headlamp High Beam

HEADLAMP

HIGH BEAM

20A

40A

10A

Headlamp Low Beam

FUSE

C/FAN

IG2

C/FAN LO Relay, C/FAN HI Relay

Start Relay, Ignition Switch (W/O Button Start), PDM Relay Box (IG2 Relay) (With

Button Start)

E3

E2

ECU3

ECU2

PCM

B3LA : PCM, Shut Off Valve #1/#2

C/FAN LO Relay, C/FAN HI Relay, A/CON Relay, Start Relay (G3LA, With ISG),

PCM, Oil Control Valve #1/#2 (IN/EX), Purge Control Solenoid Valve, Camshaft

Position Sensor #1/#2 (IN/EX)

S1

S2

SENSOR

10A

SENSOR2

G3LA/G4LA : PCM

7 67

Maintenance

Fuse Name

Symbol

Fuse rating

Circuit Protected

HEADLAMP

DIPPED

10A

Head Lamp LH

BEAMS

HEADLAMP

DIPPED

BEAMS

10A

20A

10A

15A

7.5A

Head Lamp RH

Not Used

E4

ECU4

PCM, Immobilizer Module, F/Pump 1 Relay

G3LA : Injector #1/#2/#3, G4LA : Injector #1/#2/#3/#4

B3LA : Injector #1/#2/#3 (GSL), Injector #1/#2/#3 (LPI), Crash Pad Switch

FUSE

INJECTOR

IGN COIL

B/UP LAMP

G3LA/B3LA : Ignition Coil #1/#2/#3, Condenser

G4LA : Ignition Coil

A/T : PCM, Transaxle Range Switch, BCM, Instrument Cluster, Rear Combination

Lamp LH/RH

M/T : Back-Up Lamp Switch, Smart Junction Box (Fuse : F15)

HEADLAMP

HI INDICATOR

Instrument Cluster, PCB Fuse & Relay Box (Head Lamp (H) Relay)

7 68

Maintenance

LIGHT BULBS

Consult an authorized HYUNDAI dealer

to replace most vehicle light bulbs. It is

difficult to replace vehicle light bulbs

because other parts of the vehicle must

be removed before you can get to the

bulb. This is especially true for removing

the headlight assembly to get to the

bulb(s). Removing/installing the head-

light assembly can result in damage to

the vehicle.

CAUTION

WARNING

Be sure to replace the burned-out

bulb with one of the same wattage

rating. Otherwise, it may cause

damage to the fuse or electric

wiring system.

• Prior to replacing a light, depress

the foot brake, move the shift

lever into the P (Park, for auto-

matic transaxle vehicle) or neu-

tral (for manual transaxle vehi-

cle), apply the parking brake,

place the ignition

switch in the LOCK/OFF position,

and take the key with you when

leaving the vehicle to avoid sud-

den movement of the vehicle and

to prevent possible electric

shock.

✽

NOTICE

After heavy driving, rain or washing

headlight and taillight lenses could

appear frosty. This condition is caused

by the temperature difference between

the lamp inside and outside. This is sim-

ilar to the condensation on your win-

dows inside your vehicle during the rain

and doesn’t indicate a problem with

your vehicle. If the water leaks into the

lamp bulb circuitry, we recommend that

the system be checked by an authorized

HYUNDAI dealer.

• Be aware the bulbs may be hot

and may burn your fingers.

7 69

Maintenance

(Continued)

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

• Wear eye protection when chang-

ing a bulb. Allow the bulb to cool

down before handling it.

✽

NOTICE

If the headlight aiming adjustment is

necessary after the headlight assembly is

reinstalled, consult an authorized

HYUNDAI dealer.

OBA073018

OHD076046

Headlight, position light, turn sig-

nal light, and front fog light bulb

replacement

WARNING - Halogen bulbs

• Halogen bulbs contain pressur-

ized gas that will produce flying

pieces of glass if broken.

• Always handle them carefully,

and avoid scratches and abra-

sions. If the bulbs are lit, avoid

contact with liquids. Never touch

the glass with bare hands.

Residual oil may cause the bulb

to overheat and burst when lit. A

bulb should be operated only

when installed in a headlight.

(1) Headlight (Low/High)

(2) Parking(Position) light

(3) Front turn signal light

(4) Front fog light / Daytime running light

(if equipped)

(Continued)

7 70

Maintenance

Turn signal light

Parking(Position) light

1.Remove the turn signal light bulb cover

by turning it counterclockwise.

1.Remove the socket from the assembly

by pulling it straight out.

Headlight

2.Remove the socket from the assembly

by turning the socket counterclockwise

until the tabs on the socket align with

the slots on the assembly.

2.Remove the bulb from the socket by

pulling it out.

3.Insert a new bulb by inserting it into the

socket.

3.Insert a new bulb by inserting it into the

socket and rotating it until it locks into

place.

4.Install the socket in the assembly by

aligning the tabs on the socket with the

slots in the assembly. Push the socket

into the assembly and turn the socket

clockwise.

4.Install the socket in the assembly by

pushing it in.

Parking(Position)

light

Turn signal light

OBA073047R

Headlight (Low/High)

1.Open the hood.

5.Install the turn signal light bulb cover

by turning it clockwise.

2.Remove the headlight bulb cover by

turning it counterclockwise.

3.Disconnect the headlight bulb socket-

connector.

4.Unsnap the headlight bulb retaining

wire by depressing the end and push-

ing it upward.

5.Remove the bulb from the headlight

assembly.

6.Install a new headlight bulb and snap

the headlight bulb retaining wire into

position by aligning the wire with the

groove on the bulb.

7.Connect the headlight bulb socket con-

nector.

8.Install the headlight bulb cover by turn-

ing it clockwise.

7 71

Maintenance

■ 5 Door

Front fog light bulb replacement

1.Reach your hand into the back of the

front bumper.

2.Disconnect the power connector from

the socket.

3.Remove the bulb-socket from the

housing by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the housing.

4.Install the new bulb-socket into the

housing by aligning the tabs on the

socket with the slots in the housing.

Push the socket into the housing and

turn the socket clockwise.

5.Connect the power connector to the

socket.

OBA073020

■ 4 Door

OBA073019R

Side repeater light bulb replace-

ment

If the light bulb does not operate, we rec-

ommend that the vehicle be checked by

an authorized HYUNDAI dealer.

6.Reinstall the front bumper under cover.

OBA074049

Rear combination light bulb

replacement

(1) Stop and tail light

(2) Back up light

(3) Rear turn signal light

7 72

Maintenance

■ 5 Door

5.Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket. Pull

the bulb out of the socket.

Stop and tail light

6.Insert a new bulb by inserting it into the

socket and rotating it until it locks into

place.

7.Install the socket in the assembly by

aligning the tabs on the socket with the

slots in the assembly. Push the socket

into the assembly and turn the socket

clockwise.

Turn signal light

Back up light

OBA073046R

■ 4 Door

Stop and tail light

OBA073045R

8.Reinstall the light assembly to the body

of the vehicle.

1.Open the tailgate/trunk.

2.Loosen the light assembly retaining

screws with a cross-tip screwdriver.

3.Remove the rear combination light

assembly from the body of the vehicle.

Back up light

Turn signal light

OBA074046

4.Remove the socket from the assembly

by turning the socket counterclockwise

until the tabs on the socket align with

the slots on the assembly.

7 73

Maintenance

■ 5 Door

Rear fog light bulb replacement

(if equipped)

If the light does not operate, we recom-

mend that the system be checked by an

authorized HYUNDAI dealer.

OBA073021

■ 4 Door

OBA073022

License plate light bulb replace-

ment

1.Using a flat-blade screwdriver, remove

the light assembly from the body of the

vehicle by prying the housing and

pulling the assembly out.

2.Separate the socket and the lens part

by turning the socket counterclockwise

until the tabs on the socket align with

the slots on the lens part.

3.Remove the bulb by pulling it straight

out.

4.Insert a new bulb in the socket.

5.Reassemble the socket and the hous-

ing part.

OBA074021

High mounted stop light replace-

ment

If the light does not operate, we recom-

mend that the system be checked by an

authorized HYUNDAI dealer.

6.Reinstall the light assembly to the body

of the vehicle.

7 74

Maintenance

■ Room lamp

■ Luggage room lamp

Interior light bulb replacement

1.Using a flat-blade screwdriver, gently

pry the lens from the interior light hous-

ing.

2.Remove the bulb by pulling it straight

out.

3.Install a new bulb in the socket.

4.Align the lens tabs with the interior light

housing notches and snap the lens into

place.

CAUTION

Be careful not to dirty or damage

lens, lens tab, and plastic housings.

■ Glove box lamp

OTD079037/OBA073024/OBA073023

7 75

Maintenance

APPEARANCE CARE

Even prompt washing with plain water

may not completely remove all these

deposits. A mild soap, safe for use on

painted surfaces, may be used.

After washing, rinse the vehicle thor-

oughly with lukewarm or cold water. Do

not allow soap to dry on the finish.

Exterior care

Exterior general caution

It is very important to follow the label

directions when using any chemical

cleaner or polish. Read all warning and

caution statements that appear on the

label.

CAUTION

Finish maintenance

Washing

To help protect your vehicle’s finish from

rust and deterioration, wash it thoroughly

and frequently at least once a month with

lukewarm or cold water.

Do not use strong soap, chemical

detergents or hot water, and do not

wash the vehicle in direct sunlight

or when the body of the vehicle is

warm.

OJB037800

CAUTION

If you use your vehicle for off-road driv-

ing, you should wash it after each off-

road trip. Pay special attention to the

removal of any accumulation of salt, dirt,

mud, and other foreign materials. Make

sure the drain holes in the lower edges of

the doors and rocker panels are kept

clear and clean.

Insects, tar, tree sap, bird droppings,

industrial pollution and similar deposits

can damage your vehicle’s finish if not

removed immediately.

• Water washing in the engine com-

partment including high pressure

water washing may cause the fail-

ure of electrical circuits located in

the engine compartment.

WARNING - Wet brakes

After washing the vehicle, test the

brakes while driving slowly to see if

they have been affected by water. If

braking performance is impaired,

dry the brakes by applying them

lightly while maintaining a slow for-

ward speed.

• Never allow water or other liquids

to come in contact with electri-

cal/electronic components inside

the vehicle as this may damage

them.

7 76

Maintenance

Waxing

Finish damage repair

Bright-metal maintenance

Wax the vehicle when water will no

longer bead on the paint.

Deep scratches or stone chips in the

painted surface must be repaired

promptly. Exposed metal will quickly rust

and may develop into a major repair

expense.

• To remove road tar and insects, use a

tar remover, not a scraper or other

sharp object.

• To protect the surfaces of bright-metal

parts from corrosion, apply a coating of

wax or chrome preservative and rub to

a high luster.

• During winter weather or in coastal

areas, cover the bright metal parts with

a heavier coating of wax or preserva-

tive. If necessary, coat the parts with

non-corrosive petroleum jelly or other

protective compound.

Always wash and dry the vehicle before

waxing. Use a good quality liquid or

paste wax, and follow the manufacturer’s

instructions. Wax all metal trim to protect

it and to maintain its luster.

Removing oil, tar, and similar materials

with a spot remover will usually strip the

wax from the finish. Be sure to re-wax

these areas even if the rest of the vehicle

does not yet need waxing.

✽

NOTICE

If your vehicle is damaged and requires

any metal repair or replacement, be sure

the body shop applies anti-corrosion

materials to the parts repaired or

replaced.

CAUTION

• Wiping dust or dirt off the body

with a dry cloth will scratch the

finish.

• Do not use steel wool, abrasive

cleaners, or strong detergents

containing highly alkaline or

caustic agents on chrome-plated

or anodized aluminum parts. This

may result in damage to the pro-

tective coating and cause discol-

oration or paint deterioration.

7 77

Maintenance

Underbody maintenance

Aluminum wheel maintenance

WARNING

Corrosive materials used for ice and

snow removal and dust control may col-

lect on the underbody. If these materials

are not removed, accelerated rusting can

occur on underbody parts such as the

fuel lines, frame, floor pan and exhaust

system, even though they have been

treated with rust protection.

Thoroughly flush the vehicle underbody

and wheel openings with lukewarm or

cold water once a month, after off-road

driving and at the end of each winter. Pay

special attention to these areas because

it is difficult to see all the mud and dirt. It

will do more harm than good to wet down

the road grime without removing it. The

lower edges of the doors, rocker panels,

and frame members have drain holes

that should not clog with dirt; trapped

water in these areas can cause rusting.

The aluminum wheels are coated with a

clear protective finish.

• Do not use any abrasive cleaner, pol-

ishing compound, solvent, or wire

brushes on aluminum wheels. They

may scratch or damage the finish.

• Use only a mild soap or neutral deter-

gent, and rinse thoroughly with water.

Also, be sure to clean the wheels after

driving on salted roads. This helps pre-

vent corrosion.

• Avoid washing the wheels with high-

speed car wash brushes.

After washing the vehicle, test the

brakes while driving slowly to see if

they have been affected by water. If

braking performance is impaired,

dry the brakes by applying them

lightly while maintaining a slow for-

ward speed.

• Do not use any acid detergent. It may

damage and corrode the aluminum

wheels coated with a clear protective

finish.

7 78

Maintenance

High-corrosion areas

Moisture breeds corrosion

Corrosion protection

Protecting your vehicle from corrosion

If you live in an area where your car is

regularly exposed to corrosive materials,

corrosion protection is particularly impor-

tant. Some of the common causes of

accelerated corrosion are road salts,

dust control chemicals, ocean air and

industrial pollution.

Moisture creates the conditions in which

corrosion is most likely to occur. For

example, corrosion is accelerated by

high humidity, particularly when tempera-

tures are just above freezing. In such

conditions, the corrosive material is kept

in contact with the vehicle’s surfaces with

moisture that slowly evaporate.

By using the most advanced design and

construction practices to combat corro-

sion, we produces cars of the highest

quality. However, this is only part of the

job. To achieve the long-term corrosion

resistance your vehicle can deliver, the

owner's cooperation and assistance is

also required.

Mud is particularly corrosive because it

dries slowly and holds moisture in con-

tact with the vehicle. Although the mud

appears to be dry, it can still retain mois-

ture and promote corrosion.

Common causes of corrosion

The most common causes of corrosion

on your car are:

High temperatures can also accelerate

corrosion of parts that are not properly

ventilated so the moisture can be dis-

persed. For all these reasons, it is par-

ticularly important to keep your vehicle

clean and free of mud or accumulations

of other materials. This applies not only

to the visible surfaces but particularly to

the underside of the vehicle.

• Road salt, dirt and moisture that is

allowed to accumulate underneath the

car.

• Removal of paint or protective coatings

by stones, gravel, abrasion or minor

scrapes and dents which leave unpro-

tected metal exposed to corrosion.

7 79

Maintenance

To help prevent corrosion

You can help prevent corrosion from get-

ting started by observing the following:

• When cleaning underneath the vehicle,

give particular attention to the compo-

nents under the fenders and other

areas that are hidden from view. Do a

thorough job; just dampening the accu-

mulated mud rather than washing it

away will accelerate corrosion rather

than prevent it. Water under high pres-

sure and steam are particularly effec-

tive in removing accumulated mud and

corrosive materials.

• When cleaning lower door panels,

rocker panels and frame members, be

sure that drain holes are kept open so

that moisture can escape and not be

trapped inside to accelerate corrosion.

Keep paint and trim in good condition

Scratches or chips in the finish should be

covered with "touch-up" paint as soon as

possible to reduce the possibility of cor-

rosion. If bare metal is showing through,

the attention of a qualified body and paint

shop is recommended.

Keep your vehicle clean

The best way to prevent corrosion is to

keep your vehicle clean and free of cor-

rosive materials. Attention to the under-

side of the vehicle is particularly impor-

tant.

Bird droppings : Bird droppings are high-

ly corrosive and may damage painted

surfaces in just a few hours. Always

remove bird droppings as soon as possi-

ble.

• If you live in a high-corrosion area —

where road salts are used, near the

ocean, areas with industrial pollution,

acid rain, etc.—, you should take extra

care to prevent corrosion. In winter,

hose off the underside of your vehicle

at least once a month and be sure to

clean the underside thoroughly when

winter is over.

Don't neglect the interior

Moisture can collect under the floor mats

and carpeting and cause corrosion.

Check under the mats periodically to be

sure the carpeting is dry. Use particular

care if you carry fertilizers, cleaning

materials or chemicals in the vehicle.

These should be carried only in proper

containers and any spills or leaks should

be cleaned up, flushed with clean water

and thoroughly dried.

Keep your garage dry

Don't park your vehicle in a damp, poorly

ventilated garage. This creates a favor-

able environment for corrosion. This is

particularly true if you wash your vehicle

in the garage or drive it into the garage

when it is still wet or covered with snow,

ice or mud. Even a heated garage can

contribute to corrosion unless it is well

ventilated so moisture is dispersed.

7 80

Maintenance

Cleaning the upholstery and interior

trim

Vinyl

Remove dust and loose dirt from vinyl

with a whisk broom or vacuum cleaner.

Clean vinyl surfaces with a vinyl cleaner.

Cleaning the lap/shoulder belt web-

bing

Interior care

Interior general precautions

Clean the belt webbing with any mild

soap solution recommended for cleaning

upholstery or carpet. Follow the instruc-

tions provided with the soap. Do not

bleach or re-dye the webbing because

this may weaken it.

Prevent caustic solutions such as per-

fume and cosmetic oil from contacting

the dashboard because they may cause

damage or discoloration. If they do con-

tact the dashboard, wipe them off imme-

diately. See the instructions for the prop-

er way to clean vinyl.

Fabric

Remove dust and loose dirt from fabric

with a whisk broom or vacuum cleaner.

Clean with a mild soap solution recom-

mended for upholstery or carpets.

Remove fresh spots immediately with a

fabric spot cleaner. If fresh spots do not

receive immediate attention, the fabric

can be stained and its color can be

affected. Also, its fire-resistant properties

can be reduced if the material is not

properly maintained.

Cleaning the interior window glass

If the interior glass surfaces of the vehi-

cle become fogged (that is, covered with

an oily, greasy or waxy film), they should

be cleaned with glass cleaner. Follow the

directions on the glass cleaner container.

CAUTION

Never allow water or other liquids

to

come

in

contact

with

electrical/electronic components

inside the vehicle as this may dam-

age them.

CAUTION

Do not scrape or scratch the inside

of the rear window. This may result

in damage to the rear window

defroster grid.

CAUTION

Using anything but recommended

cleaners and procedures may affect

the fabric’s appearance and fire-

resistant properties.

7 81

Maintenance

EMISSION CONTROL SYSTEM

The emission control system of your

vehicle is covered by a written limited

warranty. Please see the warranty infor-

mation contained in the Service Passport

in your vehicle.

Your vehicle is equipped with an emis-

sion control system to meet all emission

regulations.

Caution for the Inspection and

Maintenance Test (With Electronic

Stability Control (ESC) system)

• To prevent the vehicle from misfir-

ing during dynamometer testing,

turn the Electronic Stability Control

(ESC) system off by pressing the

ESC switch.

2. Evaporative emission control

System

The Evaporative Emission Control

System is designed to prevent fuel

vapors from escaping into the atmos-

phere.

Canister

There are three emission control sys-

tems which are as follows.

• After dynamometer testing is com-

pleted, turn the ESC system back on

by pressing the ESC switch again.

Fuel vapors generated inside the fuel

tank are absorbed and stored in the

onboard canister. When the engine is

running, the fuel vapors absorbed in the

canister are drawn into the surge tank

through the purge control solenoid valve.

(1) Crankcase emission control system

(2) Evaporative emission control system

(3) Exhaust emission control system

1. Crankcase emission control

system

The positive crankcase ventilation sys-

tem is employed to prevent air pollution

caused by blow-by gases being emitted

from the crankcase.This system supplies

fresh filtered air to the crankcase through

the air intake hose. Inside the crankcase,

the fresh air mixes with blow-by gases,

which then pass through the PCV valve

into the induction system.

Purge Control Solenoid Valve (PCSV)

In order to assure the proper function of

the emission control systems, it is rec-

ommended that you have your vehicle

inspected and maintained by an author-

ized HYUNDAI dealer in accordance with

the maintenance schedule in this manu-

al.

The purge control solenoid valve is con-

trolled by the Engine Control Module

(ECM); when the engine coolant temper-

ature is low during idling, the PCSV clos-

es so that evaporated fuel is not taken

into the engine. After the engine warms

up during ordinary driving, the PCSV

opens to introduce evaporated fuel to the

engine.

7 82

Maintenance

Engine exhaust gas precautions

(carbon monoxide)

• Do not operate the engine in confined

or closed areas (such as garages) any

more than what is necessary to move

the vehicle in or out of the area.

• When the vehicle is stopped in an

open area for more than a short time

with the engine running, adjust the

ventilation system (as needed) to draw

outside air into the vehicle.

• Never sit in a parked or stopped vehi-

cle for any extended time with the

engine running.

• When the engine stalls or fails to start,

excessive attempts to restart the

engine may cause damage to the

emission control system.

3. Exhaust emission control

system

The Exhaust Emission Control System is

a highly effective system which controls

exhaust emissions while maintaining

good vehicle performance.

• Carbon monoxide can be present with

other exhaust fumes. Therefore, if you

smell exhaust fumes of any kind inside

your vehicle, have it inspected and

repaired immediately. If you ever sus-

pect exhaust fumes are coming into

your vehicle, drive it only with all the

windows fully open. Have your vehicle

checked and repaired immediately.

Vehicle modifications

This vehicle should not be modified.

Modification of your vehicle could affect

its performance, safety or durability and

may even violate governmental safety

and emissions regulations.

In addition, damage or performance

problems resulting from any modification

may not be covered under warranty.

WARNING - Exhaust

Engine exhaust gases contain car-

bon monoxide (CO). Though color-

less and odorless, it is dangerous

and could be lethal if inhaled.

Follow the instructions following to

avoid CO poisoning.

7 83

Maintenance

Operating precautions for catalytic

converters (if equipped)

• Do not operate the engine at high idle

speed for extended periods (5 minutes

or more).

• Do not modify or tamper with any part

of the engine or emission control sys-

tem. We recommend that the system

be inspected by an authorized

HYUNDAI dealer.

• Avoid driving with a very low fuel level.

If you run out of gasoline, it could

cause the engine to misfire and dam-

age the catalytic converter.

Failure to observe these precautions

could result in damage to the catalytic

converter and to your vehicle.

Additionally, such actions could void your

warranties.

WARNING - Fire

A hot exhaust system can ignite

flammable items under your vehi-

cle. Do not park the vehicle over or

near flammable objects, such as

grass, vegetation, paper, leaves,

etc.

Your vehicle is equipped with a catalytic

converter emission control device.

Therefore, the following precautions

must be observed:

• Use only UNLEADED FUEL for gaso-

line engine.

• Do not operate the vehicle when there

are signs of engine malfunction, such

as misfire or a noticeable loss of per-

formance.

• Do not misuse or abuse the engine.

Examples of misuse are coasting with

the ignition off and descending steep

grades in gear with the ignition off.

7 84

Maintenance for Your Hyundai I10 4 Door Second Generation (2013-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals