Get Maintenance -> LIGHT BULBS Guide for Hyundai I10 4 Door Second Generation (2013-2019)

Maintenance

LIGHT BULBS

Consult an authorized HYUNDAI dealer

to replace most vehicle light bulbs. It is

difficult to replace vehicle light bulbs

because other parts of the vehicle must

be removed before you can get to the

bulb. This is especially true for removing

the headlight assembly to get to the

bulb(s). Removing/installing the head-

light assembly can result in damage to

the vehicle.

CAUTION

WARNING

Be sure to replace the burned-out

bulb with one of the same wattage

rating. Otherwise, it may cause

damage to the fuse or electric

wiring system.

• Prior to replacing a light, depress

the foot brake, move the shift

lever into the P (Park, for auto-

matic transaxle vehicle) or neu-

tral (for manual transaxle vehi-

cle), apply the parking brake,

place the ignition

switch in the LOCK/OFF position,

and take the key with you when

leaving the vehicle to avoid sud-

den movement of the vehicle and

to prevent possible electric

shock.

✽

NOTICE

After heavy driving, rain or washing

headlight and taillight lenses could

appear frosty. This condition is caused

by the temperature difference between

the lamp inside and outside. This is sim-

ilar to the condensation on your win-

dows inside your vehicle during the rain

and doesn’t indicate a problem with

your vehicle. If the water leaks into the

lamp bulb circuitry, we recommend that

the system be checked by an authorized

HYUNDAI dealer.

• Be aware the bulbs may be hot

and may burn your fingers.

7 69

Maintenance

(Continued)

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

• Wear eye protection when chang-

ing a bulb. Allow the bulb to cool

down before handling it.

✽

NOTICE

If the headlight aiming adjustment is

necessary after the headlight assembly is

reinstalled, consult an authorized

HYUNDAI dealer.

OBA073018

OHD076046

Headlight, position light, turn sig-

nal light, and front fog light bulb

replacement

WARNING - Halogen bulbs

• Halogen bulbs contain pressur-

ized gas that will produce flying

pieces of glass if broken.

• Always handle them carefully,

and avoid scratches and abra-

sions. If the bulbs are lit, avoid

contact with liquids. Never touch

the glass with bare hands.

Residual oil may cause the bulb

to overheat and burst when lit. A

bulb should be operated only

when installed in a headlight.

(1) Headlight (Low/High)

(2) Parking(Position) light

(3) Front turn signal light

(4) Front fog light / Daytime running light

(if equipped)

(Continued)

7 70

Maintenance

Turn signal light

Parking(Position) light

1.Remove the turn signal light bulb cover

by turning it counterclockwise.

1.Remove the socket from the assembly

by pulling it straight out.

Headlight

2.Remove the socket from the assembly

by turning the socket counterclockwise

until the tabs on the socket align with

the slots on the assembly.

2.Remove the bulb from the socket by

pulling it out.

3.Insert a new bulb by inserting it into the

socket.

3.Insert a new bulb by inserting it into the

socket and rotating it until it locks into

place.

4.Install the socket in the assembly by

aligning the tabs on the socket with the

slots in the assembly. Push the socket

into the assembly and turn the socket

clockwise.

4.Install the socket in the assembly by

pushing it in.

Parking(Position)

light

Turn signal light

OBA073047R

Headlight (Low/High)

1.Open the hood.

5.Install the turn signal light bulb cover

by turning it clockwise.

2.Remove the headlight bulb cover by

turning it counterclockwise.

3.Disconnect the headlight bulb socket-

connector.

4.Unsnap the headlight bulb retaining

wire by depressing the end and push-

ing it upward.

5.Remove the bulb from the headlight

assembly.

6.Install a new headlight bulb and snap

the headlight bulb retaining wire into

position by aligning the wire with the

groove on the bulb.

7.Connect the headlight bulb socket con-

nector.

8.Install the headlight bulb cover by turn-

ing it clockwise.

7 71

Maintenance

■ 5 Door

Front fog light bulb replacement

1.Reach your hand into the back of the

front bumper.

2.Disconnect the power connector from

the socket.

3.Remove the bulb-socket from the

housing by turning the socket counter-

clockwise until the tabs on the socket

align with the slots on the housing.

4.Install the new bulb-socket into the

housing by aligning the tabs on the

socket with the slots in the housing.

Push the socket into the housing and

turn the socket clockwise.

5.Connect the power connector to the

socket.

OBA073020

■ 4 Door

OBA073019R

Side repeater light bulb replace-

ment

If the light bulb does not operate, we rec-

ommend that the vehicle be checked by

an authorized HYUNDAI dealer.

6.Reinstall the front bumper under cover.

OBA074049

Rear combination light bulb

replacement

(1) Stop and tail light

(2) Back up light

(3) Rear turn signal light

7 72

Maintenance

■ 5 Door

5.Remove the bulb from the socket by

pressing it in and rotating it counter-

clockwise until the tabs on the bulb

align with the slots in the socket. Pull

the bulb out of the socket.

Stop and tail light

6.Insert a new bulb by inserting it into the

socket and rotating it until it locks into

place.

7.Install the socket in the assembly by

aligning the tabs on the socket with the

slots in the assembly. Push the socket

into the assembly and turn the socket

clockwise.

Turn signal light

Back up light

OBA073046R

■ 4 Door

Stop and tail light

OBA073045R

8.Reinstall the light assembly to the body

of the vehicle.

1.Open the tailgate/trunk.

2.Loosen the light assembly retaining

screws with a cross-tip screwdriver.

3.Remove the rear combination light

assembly from the body of the vehicle.

Back up light

Turn signal light

OBA074046

4.Remove the socket from the assembly

by turning the socket counterclockwise

until the tabs on the socket align with

the slots on the assembly.

7 73

Maintenance

■ 5 Door

Rear fog light bulb replacement

(if equipped)

If the light does not operate, we recom-

mend that the system be checked by an

authorized HYUNDAI dealer.

OBA073021

■ 4 Door

OBA073022

License plate light bulb replace-

ment

1.Using a flat-blade screwdriver, remove

the light assembly from the body of the

vehicle by prying the housing and

pulling the assembly out.

2.Separate the socket and the lens part

by turning the socket counterclockwise

until the tabs on the socket align with

the slots on the lens part.

3.Remove the bulb by pulling it straight

out.

4.Insert a new bulb in the socket.

5.Reassemble the socket and the hous-

ing part.

OBA074021

High mounted stop light replace-

ment

If the light does not operate, we recom-

mend that the system be checked by an

authorized HYUNDAI dealer.

6.Reinstall the light assembly to the body

of the vehicle.

7 74

Maintenance

■ Room lamp

■ Luggage room lamp

Interior light bulb replacement

1.Using a flat-blade screwdriver, gently

pry the lens from the interior light hous-

ing.

2.Remove the bulb by pulling it straight

out.

3.Install a new bulb in the socket.

4.Align the lens tabs with the interior light

housing notches and snap the lens into

place.

CAUTION

Be careful not to dirty or damage

lens, lens tab, and plastic housings.

■ Glove box lamp

OTD079037/OBA073024/OBA073023

7 75

Maintenance -> LIGHT BULBS for Your Hyundai I10 4 Door Second Generation (2013-2019)

Related Topics

Maintenance

Popular Owner Manuals

Latest Owner Manuals