Get Maintenance -> Light bulbs Guide for Hyundai I20 4 Door Second Generation (2015-2020)

,204/3424-3

ꢀ!ꢁꢂꢃ#ꢄꢅꢀꢄꢆ

Consult an authorized HYUNDAI

dealer to replace most vehicle light

bulbs. It is difficult to replace vehicle

light bulbs because other parts of the

vehicle must be removed before you

can get to the bulb. This is especially

true for removing the headlight

assembly to get to the bulb(s).

i

Information

WARNING

After heavy driving, rain or washing

headlight and taillight lenses could

appear frosty. This condition is caused

by the temperature difference

between the lamp inside and outside.

This is similar to the condensation on

your windows inside your vehicle dur-

ing the rain and doesn’t indicate a

problem with your vehicle. If the

water leaks into the lamp bulb circuit-

ry, we recommend that the system be

checked by an authorized HYUNDAI

dealer.

Prior to replacing a light, depress

the foot brake, move the shift lever

into the P (Park, for Continuously

Variable Transaxle vehicle) or

neutral (for Manual Transaxle

vehicle), apply the parking brake,

place the ignition switch in the

LOCK/OFF position, and take the

key with you when leaving the

vehicle to avoid sudden move-

ment of the vehicle and to prevent

possible electric shock.

Removing/installing the headlight

assembly can result in damage to

the vehicle.

Be aware the bulbs may be hot

and may burn your fingers.

Be sure to replace the burned-out

bulb with one of the same wattage

rating. Otherwise, it may cause dam-

age to the fuse or electric wiring sys-

tem.

1.$#

■ 5 Door

• Type B

■ Cross

• Type A

Headlight, Parking (Position)

Light, Turn signal Light, Low

Beam Assist-Static Light, Fog

Light and Daytime Running Light

bulb replacement

■ 5 Door

• Type A

OIB077069

OIB077070

(1) Headlight (Low/High) *²

(2) Low Beam Assist-Static Light

(3) Front Turn Signal Light

(1) Headlight (Low/High) *¹

(2) Parking (Position) Light

(3) Front Turn signal Light

(4) Position Light/

(4) Front Fog Light (if equipped)

OIB077068

Daytime Running Light (DRL)

(1) Headlight (Low/High) *¹

(2) Parking (Position) Light

(3) Front Turn signal Light

*¹: MFR (Multi Focus Reflector)

Headlight

(5) Front Fog Light (if equipped)

*²: Bi-Function Projection Headlight

(4) Daytime Running Light

(if equipped)

(5) Front Fog Light (if equipped)

*¹: MFR (Multi Focus Reflector)

Headlight

1.$$

,204/3424-3

■ Cross

• Type B

(Continued)

• Always handle them carefully,

and avoid scratches and abra-

sions. If the bulbs are lit, avoid

contact with liquids. Never touch

the glass with bare hands.

Residual oil may cause the bulb

to overheat and burst when lit. A

bulb should be operated only

when installed in a headlight.

• If a bulb becomes damaged or

cracked, replace it immediately

and carefully dispose of it.

• Wear eye protection when

changing a bulb. Allow the bulb

to cool down before handling it.

OIB077060

OLMB073042L

(1) Headlight (Low/High) *²

WARNING

(2) Low Beam Assist-Static Light

(3) Front Turn Signal Light

Halogen bulbs

(4) Position Light/

• Halogen bulbs contain pressur-

ized gas that will produce flying

pieces of glass if broken.

Daytime Running Light (DRL)

(5) Front Fog Light (if equipped)

(Continued)

*²: Bi-Function Projection Headlight

i

Information

• If the headlight aiming adjustment

is necessary after the headlight

assembly is reinstalled, consult an

authorized HYUNDAI dealer.

• The Fog Light aiming adjustment

can be done by removing UNDER

COVER. Consult an authorised

HYUNDAI dealer.

1.$'

4. Unsnap the headlight bulb retain-

ing wire by depressing the end

and pushing it upward.

5. Remove the bulb from the head-

light assembly.

6. Install a new headlight bulb and

snap the headlight bulb retaining

wire into position by aligning the

wire with the groove on the bulb.

7. Connect the headlight bulb socket

connector.

Headlight (Low/High)

Turn signal light

1. Remove the turn signal light bulb

cover by turning it counterclock-

wise.

2. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

3. Insert a new bulb by inserting it

into the socket and rotating it until

it locks into place.

4. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

■ MFR (Multi Focus Reflector) Headlight

Headlight

Parking

(Position) light

Turn signal light

OIB074048

Headlight

8. Install the headlight bulb cover by

turning it clockwise.

■ Bi-Function Projection Headlight

i

Information

- Bi-Function projection

headlight

5. Install the turn signal light bulb

cover by turning it clockwise.

This headlight is bi-function type that

switches the low beam to high or the

high beam to low using solenoid sys-

tem. So, the moving sound may be

heard when the headlight switches the

low beam to high or the high beam to

low and it does not indicate malfunc-

tion of the headlight.

Turn signal light

OIB075061

1. Open the hood.

2. Remove the headlight bulb cover

by turning it counterclockwise.

3. Disconnect the headlight bulb

socket-connector.

1.$1

,204/3424-3

6. Install a new Low Beam Assist-

Static Light bulb and snap the Low

Beam Assist-Static Light bulb

retaining wire into position by

aligning the wire with the groove

on the bulb.

Low Beam Assist-Static Light

Front fog light or Daytime running

light (if equipped)

■ 5 Door

• Type A (with DRL)

7. Connect the Low Beam Assist-

Static Light bulb socket connector.

8. Install the Low Beam Assist-Static

Light bulb cover by turning it clock-

wise.

OIB077071

Low Beam Assist-Static Light

■ 5 Door

OIB075061

• Type A (without DRL)

Parking (Position) light

1. Open the hood.

1. Remove the socket from the

assembly by pulling it straight out.

2. Remove the bulb from the socket

by pulling it out.

2. Remove the Low Beam Assist-

Static Light bulb cover by turning it

counterclockwise.

3. Disconnect the Low Beam Assist-

Static Light bulb socket-connector.

4. Unsnap the Low Beam Assist-

Static Light bulb retaining wire by

depressing the end and pushing it

upward.

3. Insert a new bulb by inserting it

into the socket.

4. Install the socket in the assembly

by pushing it in.

OIB077072

■ Cross

5. Remove the bulb from the Low

Beam Assist-Static Light assem-

bly.

OIB077073

1.'ꢀ

1. Remove the under cover by rotat-

ing the screws and bolts.

Position light/Daytime running light

(if equipped)

Side repeater light (LED)

replacement (if equipped)

2. Reach your hand into the back of

the front bumper.

3. Disconnect the power connector

from the socket.

4. Remove the bulb-socket from the

housing by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the housing.

Your vehicle is equipped with LED

lamps. LED lamps do not have

replaceable bulbs. If the LED lamp

does not operate, we recommend

that the vehicle be checked by an

authorized HYUNDAI dealer.

5. Install the new bulb-socket into the

housing by aligning the tabs on

the socket with the slots in the

housing. Push the socket into the

housing and turn the socket clock-

wise.

OIB074035

If the light does not operte, we rec-

ommend that the vehicle be checked

by an authorized HYUNDAI dealer.

6. Connect the power connector to

the socket.

7. Reinstall the front bumper under

cover.

1.'&

,204/3424-3

■ Cross

2. Remove the bulb by pulling it

straight out.

Interior light bulb replacement

■ Room lamp

3. Install a new bulb in the socket.

4. Align the lens tabs with the interior

light housing notches and snap

the lens into place.

NOTICE

Be careful not to dirty or damage

lens, lens tab, and plastic housings.

OIB074040

1. Using a flat-blade screwdriver,

remove the light assembly from

the body of the vehicle by prying

the housing and pulling the

assembly out.

OIB074041

■ Luggage room lamp

2. Separate the socket and the lens

part by turning the socket counter-

clockwise until the tabs on the

socket align with the slots on the

lens part.

3. Remove the bulb by pulling it

straight out.

4. Insert a new bulb in the socket.

OIB074042

1. Using a flat-blade screwdriver,

gently pry the lens from the interi-

or light housing.

5. Reassemble the socket and the

housing part.

6. Reinstall the light assembly to the

body of the vehicle.

1.')

Maintenance -> Light bulbs for Your Hyundai I20 4 Door Second Generation (2015-2020)

Related Topics

Popular Owner Manuals

Latest Owner Manuals