Get Emergency situations -> If you have a flat tyre (with Tyre Mobility Kit, if equipped) Guide for Hyundai Ioniq SUV First Generation (2021-2026)

Emergency situations

,)ꢀ<28ꢀ+$9(ꢀ$ꢀ)/$7ꢀ7<5(ꢀǣ:,7+ꢀ7<5(ꢀ02%,/,7<ꢀ.,7ꢁꢀ

,)ꢀ(48,33('Ǥ

Introduction

With the Tyre Mobility Kit you stay mobile

even after experiencing a tyre puncture.

The compressor and sealing compound

system effectively and comfortably seals

most punctures in a passenger car tyre

caused by nails or similar objects and

reinflates the tyre.

After you ensure that the tyre is properly

sealed you can drive cautiously on the

tyre (distance up to 200 km) at a max.

speed of 80 km/h in order to reach a

service station or tyre dealer for the tyre

replacement.

It is possible that some tyres, especially

with larger punctures or damage to the

sidewall, cannot be sealed completely.

ONE1081029

For safe operation, carefully read and

follow the instructions in this manual

before use.

(1) Compressor

(2) Sealant bottle

The tyre mobility kit is a temporary fix

to the tyre we recommend the tyre be

inspected by an authorised HYUNDAI

dealer or the equivalent approved for

your vehicle as soon as possible.

Air pressure loss in the tyre may

adversely affect tyre performance.

For this reason, you should avoid abrupt

steering or other driving manoeuvres,

especially if the vehicle is heavily loaded

or if a trailer is in use.

The Tyre Mobility Kit is not designed

or intended as a permanent tyre repair

method and is to be used for one tyre

only.

This instruction shows you step by step

how to temporarily seal the puncture

simply and reliably.

CAUTION

When two or more tyres are flat, do not

use the tyre mobility kit because the

sealant provided with the Tyre Mobility

Kit must be used for only one flat tyre.

WARNING

Do not use the Tyre Mobility Kit to repair

punctures in the tyre walls. This can

result in an accident due to tyre failure.

Read the section “Notes on the safe use

of the Tyre Mobility Kit”.

WARNING

Have your tyre repaired as soon as

possible. The tyre may lose air pressure

at any time after inflating with the Tyre

Mobility Kit.

8-12

08

śꢀ Never leave the Tyre Mobility Kit

WARNING

Do not use the TMK if a tyre is severely

damaged by driving run flat or with

insufficient air pressure.

Only punctured areas located within the

tread region of the tyre can be sealed

using the TMK.

unsupervised whilst it is being used.

śꢀ Do not leave the compressor running

for more than 10 min. at a time or it

may overheat.

śꢀ Do not use the Tyre Mobility Kit if the

ambient temperature is below -30°C

(-22°F).

śꢀ In case of skin contact with the

sealant, wash the area thoroughly

with plenty of water. If the irritation

persists, seek medical attention.

śꢀ In case of eye contact with the

sealant, flush your eyes for at least 15

minutes. If the irritation persists, seek

medical attention.

śꢀ In case of swallowing the sealant,

rinse the mouth and drink plenty of

water. However, never give anything

to an unconscious person and seek

medical attention immediately.

śꢀ Long time exposure to the sealant

may cause damage to bodily tissue

such as kidney, etc.

Notes on the safe use of the Tyre

Mobility Kit

śꢀ Park your car at the side of the road

so that you can work with the Tyre

Mobility Kit away from moving traffic.

śꢀ To be sure your vehicle will not move,

even when you’re on fairly level

ground, always set your parking brake.

śꢀ Only use the Tyre Mobility Kit for

sealing/inflation passenger car tyres.

Only punctured areas located within

the tread region of the tyre can be

sealed using the tyre mobility kit.

śꢀ Do not use on motorcycles, bicycles

or any other type of tyres.

śꢀ When the tyre and wheel are

damaged, do not use Tyre Mobility Kit

for your safety.

śꢀ Use of the Tyre Mobility Kit may not be

effective for tyre damage larger than

approximately 6 mm (0.24 in).

śꢀ If the tyre cannot be made roadworthy

with the Tyre Mobility Kit, we

recommend that you contact an

authorised HYUNDAI dealer.

śꢀ Do not use the Tyre Mobility Kit if a

tyre is severely damaged by driving

run flat or with insufficient air

pressure.

śꢀ Do not remove any foreign objects

such as nails or screws that have

penetrated the tyre.

śꢀ Provided the car is outdoors, leave the

Vehicle is ON (

indicator ON).

Otherwise operating the compressor

may eventually drain the car battery.

8-13

Emergency situations

Components of the Tyre Mobility Kit

ONE1081030

1. Speed-restriction label

2. Sealant bottle and label with speed restriction

3. Filling hose

4. Connectors and cable for the power outlet direct connection

5. Holder for the sealant bottle

6. Compressor

7. ON/OFF switch

8. Pressure gauge for displaying the tyre inflation pressure

9. Button for reducing the tyre inflation pressure

Connectors, cable and connection hose are stored in the compressor housing.

Strictly follow the specified sequence, otherwise the sealant may escape under high

pressure.

WARNING

Expired sealant

Do not use the Tyre sealant after the sealant has expired (for example, pasted the

expiration date on the sealant container). This can increase the risk of tyre failure.

8-14

08

1. Shake the sealant bottle (2).

WARNING

Sealant

śꢀ Keep out of reach of children.

śꢀ Avoid contact with eyes.

śꢀ Do not swallow.

Using the Tyre Mobility Kit When

a tyre is flat

CAUTION

ONE1081031

2. Connect the filling hose (3) to the

sealant bottle (2) in the direction of (A)

and connect the sealant bottle to the

compressor (6) in the direction of (B).

3. Ensure that the compressor is

switched OFF.

4. Unscrew the valve cap from the valve

of the defective wheel and screw the

filling hose (3) of the sealant bottle

onto the valve.

ONE1081008R

Detach the speed restriction label (1)

from the sealant bottle (2), and place

it in a highly visible place inside the

vehicle such as on the steering wheel to

remind the driver not to drive too fast.

CAUTION

If only the tyre pressure needs to be

adjusted, refer to “How to Adjust Tyre

Pressure” in this chapter.

ONE1081009

Before using the Tyre Mobility Kit, be

fully aware of the explanation on the

sealant.

CAUTION

Securely install the sealant filling hose

to the valve. If not, sealant may flow

rearward, possibly clogging the filling

hose.

8-15

Emergency situations

7. Switch off the compressor.

8. Detach the hoses from the sealant

bottle connector and from the tyre

valve.

Return the Tyre Mobility Kit to its storage

location in the vehicle.

ONE1081010R

5. Plug the compressor power cord (4)

into the vehicle power outlet.

NOTICE

Only use the front passenger side

power outlet when connecting the

power cord.

OLMF064106

9. Immediately drive approximately 7~10

km (about 10min) to evenly distribute

the sealant in the tyre.

Do not exceed a speed of 80 km/h. If

possible, do not fall below a speed of 20

km/h.

Whilst driving, if you experience any

unusual vibration, ride disturbance or

noise, reduce your speed and drive with

caution until you can safely pull off of the

side of the road.

6. With the vehicle ON

(

indicator ON), switch on

the compressor and let it run for

approximately 5~7 minutes to fill the

sealant up to proper pressure. (refer

to the Tyre and Wheels, chapter 2).

The inflation pressure of the tyre

after filling is unimportant and will be

checked/corrected later.

Be careful not to overinflate the tyre

and stay away from the tyre when

filling it.

Call for road side service or towing.

CAUTION

Tyre pressure

Do not attempt to drive your vehicle if

the tyre pressure is below 200 kPa (29

psi). This could result in an accident due

to sudden tyre failure.

8-16

08

NOTICE

Do not let the compressor run for more

than 10 minutes, otherwise the device

will overheat and may be damaged.

Information

The pressure gauge may show higher than

actual reading when the compressor is

running. To get an accurate tyre reading,

the compressor needs to be turned off.

OIGH067043

CAUTION

If the inflation pressure is not

maintained, drive the vehicle a second

time, refer to step 9.

Then repeat steps 10 to 13.

Use of the TMK may be ineffectual for

tyre damage larger than approximately

4 mm.

We recommend that you contact an

authorised HYUNDAI dealer if the tyre

cannot be made roadworthy with the

Tyre Mobility Kit.

ONE1081009

10. After driving approximately 7~10

km (about 10 min), stop at a safety

location.

11. Connect the filling hose (3) of the

compressor directly to the tyre valve.

12. Plug the compressor power cord into

the vehicle power outlet.

13. Adjust the tyre inflation pressure to

the recomended tyre inflation.

WARNING

The tyre inflation pressure must be at

least 220 kPa (32 psi). If it is not, do not

continue driving.

Call for road side service or towing.

With the Vehicle is ON

CAUTION

Tyre pressure sensor (if equipped with

TPMS)

The sealant on the tyre pressure sensor

and wheel should be removed when

you replace the tyre with a new one and

inspect the tyre pressure sensors. We

recommend that you get this done at an

authorised HYUNDAI dealer.

(

indicator ON) proceed as

follows.

- To increase the inflation pressure

: Switch on the compressor. To

check the current inflation pressure

setting, briefly switch off the

compressor.

- To reduce the inflation pressure:

Press the button (9) on the

compressor.

8-17

Emergency situations

4. Adjust the tyre inflation pressure to

the recomended tyre inflation.

Information

When reinstalling the repaired or replaced

tyre and wheel on the vehicle, tighten

the wheel lug nut to 11~13 kgf·m (79~94

lbf·ft).

With the Vehicle is ON

(

indicator ON), proceed as

follows.

- To increase the inflation pressure

: Switch on the compressor. To

check the current inflation pressure

setting, briefly switch off the

compressor.

How to adjust tyre pressure

- To reduce the inflation pressure:

Press the button (9) on the

compressor.

NOTICE

Do not let the compressor run for more

than 10 minutes, otherwise the device

will overheat and may be damaged.

OIGH067043

Information

śꢀ The pressure gauge may show

higher than actual reading when the

compressor is running. To get an

accurate tyre reading, the compressor

needs to be turned off.

śꢀ When reinstalling the repaired or

replaced tyre and wheel on the vehicle,

tighten the wheel lug nut to 11~13kgf·m

(79~94 lbf·ft).

ONE1081009

1. Park your vehicle in a safe location.

2. Connect the filling hose (3) of the

compressor directly to the tyre valve.

3. Plug the compressor power cord into

the vehicle power outlet.

CAUTION

Do not use the sealant when the tyre

pressure only needs to be adjusted.

WARNING

The tyre inflation pressure must be at

least 220 kPa (32 psi). If it is not, do not

continue driving.

Call for road side service or towing.

8-18

Emergency situations -> If you have a flat tyre (with Tyre Mobility Kit, if equipped) for Your Hyundai Ioniq SUV First Generation (2021-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals