Get Maintenance -> Light Bulbs Guide for Hyundai Ix35 SUV Second Generation (2016-2023)

LIGHT BULBS

WARNING

✽

NOTICE

CAUTION

After heavy, driving rain or wash-

ing, headlight and taillight lenses

could appear frosty. This condition

is caused by the temperature differ-

ence between the lamp inside and

Working on the lights

If you don’t have necessary

tools, the correct bulbs and the

expertise, consult an authorized

HYUNDAI dealer. In many cases,

it is difficult to replace vehicle

light bulbs because other parts

of the vehicle must be removed

before you can get to the bulb.

This is especially true if you

have to remove the headlight

assembly to get to the bulb(s).

Prior to working on the light,

firmly apply the parking brake,

ensure that the ignition switch

is turned to the“LOCK”position

and turn off the lights to avoid

sudden movement of the vehi-

cle and burning your fingers or

receiving an electric shock.

outside.

This is similar to the con-

densation on your windows inside

your vehicle during the rain and

doesn’t indicate

your vehicle. If the water leaks into

the lamp bulb circuitry, we recom-

mend that the system be checked by

an authorized HYUNDAI dealer.

a

problem with

Removing/installing the head-

light assembly can result in

damage to the vehicle.

Use only the bulbs of the specified

wattage.

CAUTION

Be sure to replace the burned-

out bulb with one of the same

wattage rating. Otherwise, it

may cause damage to the fuse

or electric wiring system.

7

7-81

Maintenance

Headlamp bulb

Headlamp, position lamp,

Front turn signal lamp, front

fog lamp bulb replacement

(Continued)

Never touch the glass with

bare hands. Residual oil may

cause the bulb to overheat

and burst when lit. A bulb

should be operated only when

installed in a headlamp.

• If a bulb becomes damaged or

cracked, replace it immediate-

ly and carefully dispose of it.

• Wear eye protection when

changing a bulb. Allow the

bulb to cool down before han-

dling it.

OLMB073042L

OLMB073041

WARNING

(1) Front turn signal lamp

(2) Headlamp (High/Low)

(3) Position lamp (LED)

Halogen bulbs

• Halogen bulbs contain pres-

surized gas that will produce

flying pieces of glass if bro-

ken.

(4) Front fog lamp (if equipped)

(5) Position lamp (LED)/Daytime

running lamp (if equipped)

• Always handle them carefully,

and avoid scratches and abra-

sions. If the bulbs are lit, avoid

contact with liquids.

(Continued)

7-82

6. Insert a new bulb into the socket.

Turn signal lamp/Position lamp

7. Install the socket in the assembly 1. Remove the socket from the

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

8. Install the headlamp bulb cover by 2. Remove the bulb from the socket

turning it clockwise.

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket

✽

NOTICE

We recommend that the headlight

aiming be adjusted after an accident

OLMB074101

1. Open the hood.

3. Insert a new bulb into the socket

and rotating it until it locks into

place.

or after

reinstalled

HYUNDAI dealer.

the headlight assembly is

2. Remove the headlamp bulb cover

by turning it counterclockwise.

at authorized

a

4. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

3. Disconnect the headlamp bulb

socket-connector.

4. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

7

5. Remove the bulb by pulling it out.

7-83

Maintenance

Front fog lamp bulbs

(if equipped)

Type B

Side repeater lamp replace-

ment

1. Remove the front bumper under

cover.

Type A

2. Reach your hand into the back of

the front bumper.

3. Disconnect the power connector

from the socket.

4. Remove the bulb-socket from the

housing by turning the socket

counter clockwise until the tabs on

the socket align with the slots on

the housing.

OLMB073046

1. Remove the light assembly from

the vehicle by prying the lens and

pulling the assembly out.

5. Install the new bulb-socket into the

housing by aligning the tabs on

the socket with the slots in the

housing. Push the socket into the

housing and turn the socket clock-

wise.

OLMB073045

If the light bulb does not operate, we

recommend that the system be

checked by an authorized HYUNDAI

dealer.

2. Reinstall a new light assembly to

the body of the vehicle.

6. Connect the power connector to

the socket.

7. Reinstall the front bumper under

cover.

7-84

3. Loosen the lamp assembly retain-

ing screws with a cross-tip screw-

driver.

Outside lamp

Rear combination lamp bulb

replacement

4. Remove the rear combination

lamp assembly from the body of

the vehicle.

5. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

OLMB073048

6. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

OLMB073047

(1) Stop/tail lamp

(2) Rear turn signal lamp

(3) Back-up lamp

7. Insert a new bulb into the socket

and rotating it until it locks into

place.

7

8. Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

OLMB073049

Rear turn signal lamp and stop/tail

lamp

1. Turn off the engine.

2. Open the tailgate.

9. Reinstall the lamp assembly to the

body of the vehicle.

7-85

Maintenance

Tail lamp/Back-up lamp

(Bulb type)

Inside lamp

Rear fog lamp

1. Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

4.Remove the socket from the

assembly by turning the socket

counterclockwise until the tabs on

the socket align with the slots on

the assembly.

2. Remove the bulb from the socket

by pressing it in and rotating it

counterclockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

5.Tail light : Remove the bulb from

the socket by pressing it in and

rotating it counterclockwise until

the tabs on the bulb align with the

slots in the socket. Pull the bulb out

of the socket.

OLMB073051

3. Insert a new bulb in the socket.

Back-up light : Remove the bulb

from the socket by pulling it out.

6.Insert a new bulb into the socket.

7.Install the socket into the assembly

by aligning the tabs on the socket

with the slots on the assembly and

turning the socket clockwise.

OLMB073052

✽

NOTICE

If the LED type lamp does not oper-

1. Turn off the engine.

2. Open the tailgate.

ate,

we

recommend

that

you

checked an authorized HYUNDAI

dealer.

3. Remove the service cover using a

flat-blade screwdriver.

7-86

1.Open the tailgate.

High mounted stop lamp

replacement

License plate lamp bulb

replacement

2.Gently remove the center cover of

the rear tailgate trim.

3.Disconnect the electrical connec-

tor.

4.Loosen the retaining nuts and

remove the spoiler.

5.Remove the high mounted stop

lamp assembly (A) after loosening

the nuts and washer nozzle (B).

OLMB073103

6.Reinstall a new lamp assembly in

the reverse order of removal.

OLMB073054

1. Loosen the lens retaining screws

with a philips head screwdriver.

2. Remove the lens.

3. Remove the bulb by pulling it

straight out.

7

OLMB073104

4. Install a new bulb.

(A)

5. Reinstall the lens securely with the

lens retaining screws.

(B)

OLMB073105

7-87

Maintenance

■ Map lamp

■ Sunvisor lamp

Interior lamp bulb replacement

1. Using a flat-blade screwdriver,

gently pry the lens from the interi-

or lamp housing.

2. Remove the bulb by pulling it

straight out.

WARNING

■ Room lamp

Prior to working on the Interior

lamps, ensure that the “OFF”

button is depressed to avoid

burning your fingers or receiv-

ing an electric shock.

■ Glove box lamp (if equipped)

3. Install a new bulb in the socket.

4. Align the lens tabs with the interior

lamp housing notches and snap

the lens into place.

■ Luggage room lamp (if equipped)

OLMB073057/OLMB073059

CAUTION

Use care not to dirty or damage

lens, lens tab, and plastic hous-

ings.

OLMB073055/OLMB073056/OLMB073058

7-88

Maintenance -> Light Bulbs for Your Hyundai Ix35 SUV Second Generation (2016-2023)

Related Topics

Popular Owner Manuals

Latest Owner Manuals