Get What to do in an emergency Guide for Hyundai Tucson SUV Third Generation (2016-2019)

What to do in an emergency

Hazard warning flasher ........................................6-2

In case of an emergency while driving ..............6-2

If the engine stalls while driving...................................6-2

If the engine stalls at a crossroad or crossing ........6-3

If you have a flat tire while driving ............................6-3

If the engine will not start ...................................6-4

If the engine doesn't turn over or turns over

If you have a flat tire (with spare tire)............6-17

Jack and tools .................................................................6-17

Changing tires..................................................................6-18

Jack label...........................................................................6-23

EC Declaration of conformity for Jack......................6-24

If you have a flat tire (with Tire Mobility Kit)..6-25

Introduction ......................................................................6-25

Notes on the safe use of the Tire Mobility Kit.......6-26

Components of the Tire Mobility Kit .........................6-27

Using the Tire Mobility Kit............................................6-28

Distributing the sealant .................................................6-30

Checking the tire inflation pressure ..........................6-30

slowly ..................................................................................6-4

If the engine turns over normally but doesn't

start .....................................................................................6-4

Jump starting..........................................................6-4

If the engine overheats ........................................6-8

Towing ...................................................................6-33

Towing service.................................................................6-33

Removable towing hook ...............................................6-34

Emergency towing .........................................................6-35

Tire pressure monitoring system (TPMS)........6-10

Check tire pressure ........................................................6-10

Tire pressure monitoring system................................6-10

Low tire pressure telltale..............................................6-12

Low tire pressure position telltale and

tire pressure telltale.......................................................6-12

TPMS (Tire Pressure Monitoring System)

malfunction indicator.....................................................6-13

Changing a tire with TPMS...........................................6-14

6

Emergency commodity........................................6-37

Fire extinguisher .............................................................6-37

First aid kit ......................................................................6-37

Triangle reflector............................................................6-37

Tire pressure gauge .......................................................6-37

ERA-GLONASS emergency call .........................6-38

ERA-GLONASS system.................................................6-39

What to do in an emergency

HAZARD WARNNING FLASHEER

■ Type A

IN CASE OF ANN EMERGENCY

WHILE DRRIVING

To turn the hazard warning flasher

on or off, press the hazard warning

flasher button with the Engine

Start/Stop button in any position.The

button is located in the center fascia

panel. All turn signal lights will flash

simultaneously.

If the engine stalls while driving

• Reduce your speed gradually,

keeping a straight line. Move cau-

tiously off the road to a safe place.

• Turn on your hazard warning flash-

er.

• The hazard warning flasher oper-

ates whether your vehicle is run-

ning or not.

• Try to start the engine again. If your

vehicle will not start, we recom-

mend that you contact an author-

ized HYUNDAI dealer.

OTLE065001

• The turn signals do not work when

the hazard flasher is on.

■ Type B

OTLE045075

The hazard warning flasher serves as

a warning to other drivers to exercise

extreme caution when approaching,

overtaking, or passing your vehicle.

It should be used whenever emer-

gency repairs are being made or

when the vehicle is stopped near the

edge of a roadway.

6-2

• When the vehicle is stopped, press

the hazard warning flasher button,

move the shift lever into P (Park,

for automatic transaxle/dual clutch

transmission vehicle) or neutral (for

manual transaxle vehicle), apply the

parking brake, and place the ignition

switch in the LOCK/OFF position.

If the engine stalls at a cross-

road or crossing

If you have a flat tire while

driving

If the engine stalls at a crossroad or If a tire goes flat while you are driving:

crossing, if safe to do so, move the

shift lever to the N (Neutral) position

pedal and let the vehicle slow

and then push the vehicle to a safe

location.

• Take your foot off the accelerator

down while driving straight ahead.

Do not apply the brakes immedi-

ately or attempt to pull off the road

as this may cause loss of vehicle

control resulting in an accident.

When the vehicle has slowed to

such a speed that it is safe to do

so, brake carefully and pull off the

road. Drive off the road as far as

possible and park on firm, level

ground. If you are on a divided

highway, do not park in the median

area between the two traffic lanes.

• Have all passengers get out of the

vehicle. Be sure they all get out on

the side of the vehicle that is away

from traffic.

• When changing a flat tire, follow

the instructions provided later in

this chapter.

6

6-3

What to do in an emergency

IF THE ENGINE WWILL NOT START

JUMP STTARTING

Jump starting can be dangerous if

done incorrectly. Follow the jump

starting procedure in this section to

avoid serious injury or damage to

your vehicle. If in doubt about how to

properly jump start your vehicle, we

strongly recommend that you have a

service technician or towing service

do it for you.

If the engine doesn't turn over

or turns over slowly

If the engine turns over nor-

mally but doesn’t start

• Be sure the shift lever is in N • Check the fuel level and add fuel if

(Neutral) or P (Park) if it is an auto-

matic transaxle/dual clutch trans-

mission vehicle. The engine starts

only when the shift lever is in N

(Neutral) or P (Park).

necessary.

If the engine still does not start, we

recommend that you call an author-

ized HYUNDAI dealer for assistance.

• Check the battery connections to

be sure they are clean and tight.

• Turn on the interior light. If the light

dims or goes out when you operate

the starter, the battery is drained.

Do not push or pull the vehicle to start

it. This could cause damage to your

vehicle. See instructions for "Jump

Starting" provided in this chapter.

CAUTION

Push or pull starting the vehicle

may cause the catalytic con-

verter to overload which can

lead to damage to the emission

control system.

6-4

(Continued)

Batteries contain sulfu-

(Continued)

WARNING

• NEVER attempt to recharge

the battery when the vehicle’s

battery cables are connected

to the battery.

To prevent SERIOUS INJURY or

DEATH to you or bystanders,

always follow these precautions

when working near or handling

the battery:

ric acid which is highly

corrosive. Do not allow

acid to contact your

eyes, skin or clothing.

• The electrical ignition system

works with high voltage.

NEVER touch these compo-

nents with the engine running

or when the Engine Start/Stop

button is in the ON position.

If acid gets into your eyes, flush

your eyes with clean water for at

least 15 minutes and get imme-

diate medical attention. If acid

gets on your skin, thoroughly

wash the area. If you feel pain or

a burning sensation, get med-

ical attention immediately.

Always read and follow

instructions carefully

when handling a battery.

Wear eye protection

designed to protect the

eyes from acid splashes.

• Do not allow the (+) and (-)

jumper cables to touch. It may

cause sparks.

Keep all flames, sparks,

or smoking materials

away from the battery.

• When lifting a plastic-cased

battery, excessive pressure

on the case may cause battery

acid to leak. Lift with a battery

carrier or with your hands on

opposite corners.

• The battery may rupture or

explode when you jump start

with a low or frozen battery.

6

Hydrogen is always

present in battery cells,

is highly combustible,

and may explode if ignit-

ed.

• Do not attempt to jump start

your vehicle if your battery is

frozen.

Keep batteries out of

reach of children.

(Continued)

6-5

What to do in an emergency

Jump starting procedure

NOTICE

i

Information

1. Position the vehicles close enough

that the jumper cables will reach,

but do not allow the vehicles to

touch.

To prevent damage to your vehi-

cle:

An inappropriately disposed

battery can be harmful to the

environment and human

health. Dispose the battery

according to your local law(s)

or regulations.

Pb

• Only use a 12-volt power supply

(battery or jumper system) to

jump start your vehicle.

2. Avoid fans or any moving parts in

the engine compartment at all

times, even when the vehicles are

turned off.

• Do not attempt to jump start

your vehicle by push-starting.

3. Turn off all electrical devices such

as radios, lights, air conditioning,

etc. Put the vehicles in P (Park, for

automatic transaxle/dual clutch

transmission vehicle) or neutral

(for manual transaxle vehicle), and

set the parking brakes. Turn both

vehicles OFF.

6-6

7. Connect the other end of the sec- Disconnect the jumper cables in the

ond jumper cable to the black, exact reverse order you connected

negative (-) chassis ground of them:

your vehicle (4).

1. Disconnect the jumper cable from

the black, negative (-) chassis

ground of your vehicle (4).

Do not allow the jumper cables to

contact anything except the cor-

rect battery or jumper terminals or

the correct ground. Do not lean

over the battery when making

connections.

2. Disconnect the other end of the

jumper cable from the black, neg-

ative (-) battery/chassis ground of

the assisting vehicle (3).

8. Start the engine of the assisting

vehicle and let it run at approxi-

mately 2,000 rpm for a few min-

utes. Then start your vehicle.

3. Disconnect the second jumper

cable from the red, positive (+)

battery/jumper terminal of the

assisting vehicle (2).

1VQA4001

4. Connect the jumper cables in the

exact sequence shown in the illus-

tration. First connect one jumper

cable to the red, positive (+)

jumper terminal of your vehicle

(1).

If your vehicle will not start after a

few attempts, it probably requires

servicing. In this event please seek

qualified assistance. If the cause of

your battery discharging is not

apparent, have your vehicle checked

by an authorized HYUNDAI dealer.

4. Disconnect the other end of the

jumper cable from the red, positive

(+) jumper terminal of your vehicle

(1).

6

5. Connect the other end of the

jumper cable to the red, positive

(+) battery/jumper terminal of the

assisting vehicle (2).

6. Connect the second jumper cable

to the black, negative (-) battery/

chassis ground of the assisting

vehicle (3).

6-7

What to do in an emergency

IF THE ENGINEE OVERHEATS

3. If engine coolant is running out

under the vehicle or steam is com-

ing out from the hood, stop the

engine. Do not open the hood until

the coolant has stopped running

or the steaming has stopped. If

there is no visible loss of engine

coolant and no steam, leave the

engine running and check to be

sure the engine cooling fan is

operating. If the fan is not running,

turn the engine off.

WARNING

While the engine is

running, keep hands,

clothing and tools

away from the mov-

ing parts such as the

cooling fan and drive

belt to prevent seri-

ous injury.

OTL065010

If your temperature gauge indicates

overheating, you experience a loss

of power, or hear loud pinging or

knocking, the engine may be over-

heating. If this happens, you should:

4. Check for coolant leaking from the

radiator, hoses or under the vehi-

cle. (If the air conditioning had been

in use, it is normal for cold water to

be draining from it when you stop.)

1. Pull off the road and stop as soon

as it is safe to do so.

5. If engine coolant is leaking out, stop

the engine immediately and we rec-

ommend that you call an authorized

HYUNDAI dealer for assistance.

2. Place the shift lever in P (Park, for

automatic transaxle/dual clutch

transmission vehicle) or neutral (for

manual transaxle/dual clutch trans-

mission vehicle) and set the park-

ing brake. If the air conditioning is

ON, turn it OFF.

6-8

6. If you cannot find the cause of the

overheating, wait until the engine

temperature has returned to nor-

mal. Then, if coolant has been

lost, carefully add coolant to the

reservoir to bring the fluid level in

the reservoir up to the halfway

mark.

WARNING

CAUTION

NEVER remove the

radiator cap or the

drain plug while the

engine and radiator

are hot. Hot coolant

• Serious loss of coolant indi-

cates a leak in the cooling

system and we recommend

the system be checked by an

authorized HYUNDAI dealer.

and steam may blow out under

pressure, causing serious injury.

• When the engine overheats

from low engine coolant, sud-

denly adding engine coolant

may cause cracks in the

engine. To prevent damage,

add engine coolant slowly in

small quantities.

7. Proceed with caution, keeping

alert for further signs of overheat-

ing. If overheating happens again,

we recommend that you call an

authorized HYUNDAI dealer for

assistance.

Turn the engine off and wait

until the engine cools down.

Use extreme care when remov-

ing the radiator cap. Wrap a

thick towel around it, and turn it

counterclockwise slowly to the

first stop. Step back while the

pressure is released from the

cooling system. When you are

sure all the pressure has been

released, press down on the

cap, using a thick towel, and

continue turning counterclock-

wise to remove it.

6

6-9

What to do in an emergency

TIRE PREESSUREE MONITORING SSYSTEM (TPMS) (IF EQUIPPED)

Check tire pressure

• You can change the tire pressure

unit in the User Settings mode on

the instrument cluster.

■ Type B

■ Type A

- psi, kpa, bar (Refer to "User

Settings mode" in chapter 3).

OTL065003

OTLE065017/OTLE065018

• You can check the tire pressure in the

information mode on the instrument

cluster.

Refer to "User Settings mode" in

chapter 3.

• Tire pressure is displayed few min-

utes later after driving.

OTL045504L

• If tire pressure is not displayed when

the vehicle is stopped, “Drive to dis-

play” message will appear. After driv-

ing, check the tire pressure.

(1) Low Tire Pressure Telltale/

TPMS Malfunction Indicator

(2) Low tire pressure position telltale

and tire pressure telltale

(Shown on the LCD display)

6-10

As an added safety feature, your Your vehicle has also been equipped

vehicle has been equipped with a tire with a TPMS malfunction indicator to

pressure monitoring system (TPMS) indicate when the system is not

that illuminates a low tire pressure operating properly. The TPMS mal-

telltale when one or more of your function indicator is combined with

tires is significantly under-inflated. the low tire pressure telltale. When

Accordingly, when the low tire pres- the system detects a malfunction,

sure telltale illuminates, you should the telltale will flash for approximate-

stop and check your tires as soon as ly one minute and then remain con-

possible, and inflate them to the tinuously illuminated. This sequence

proper pressure. Driving on a signifi- will continue upon subsequent vehi-

cantly under-inflated tire causes the cle start-ups as long as the malfunc-

tire to overheat and can lead to tire tion exists. When the malfunction

failure. Under-inflation also reduces indicator is illuminated, the system

fuel efficiency and tire tread life, and may not be able to detect or signal

may affect the vehicle’s handling and low tire pressure as intended.

Tire pressure monitoring sys-

tem

WARNING

Over-inflation or under-inflation

can reduce tire life, adversely

affect vehicle handling, and

lead to sudden tire failure that

may cause loss of vehicle con-

trol resulting in an accident.

Each tire, including the spare (if pro-

vided), should be checked monthly

when cold and inflated to the inflation

pressure recommended by the vehi-

cle manufacturer on the vehicle plac-

ard or tire inflation pressure label. (If

your vehicle has tires of a different

size than the size indicated on the

vehicle placard or tire inflation pres-

sure label, you should determine the

proper tire inflation pressure for

those tires.)

stopping ability.

TPMS malfunctions may occur for a

Please note that the TPMS is not a variety of reasons, including the

substitute for proper tire mainte- installation of replacement or alter-

nance, and it is the driver’s responsi- nate tires or wheels on the vehicle

bility to maintain correct tire pres- that prevent the TPMS from function-

sure, even if under-inflation has not ing properly. Always check the TPMS

reached the level to trigger illumina- malfunction telltale after replacing

tion of the TPMS low tire pressure one or more tires or wheels on your

6

telltale.

vehicle to ensure that the replace-

ment or alternate tires and wheels

allow the TPMS to continue to func-

tion properly.

6-11

What to do in an emergency

If either telltale illuminates, immedi-

ately reduce your speed, avoid hard

cornering and anticipate increased

stopping distances. You should stop

and check your tires as soon as pos-

sible. Inflate the tires to the proper

pressure as indicated on the vehi-

cle’s placard or tire inflation pressure

label located on the driver’s side cen-

ter pillar outer panel. If you cannot

reach a service station or if the tire

cannot hold the newly added air,

replace the low pressure tire with a

spare tire.

Low tire pressure

telltale

NOTICE

If any of the below happens, we

recommend that the system be

checked by an authorized HYUNDAI

dealer.

Low tire pressure

position telltale

and tire pressure

telltale

1. The low tire pressure telltale/

TPMS malfunction indicator

does not illuminate for 3 sec-

onds when Engine Start/Stop

button is turned to the ON or

engine is running.

OTL045504L

2. TheTPMS malfunction indicator

remains illuminated after blink-

ing for approximately 1 minute.

When the tire pressure monitoring

system warning indicators are illumi-

nated and warning message dis-

played on the cluster LCD display,

one or more of your tires is signifi-

cantly under-inflated. The low tire

pressure position telltale light will

indicate which tire is significantly

under-inflated by illuminating the cor-

responding position light.

If you drive the vehicle for about 10

minutes at speeds above 25 km/h

after replacing the low pressure tire

with the spare tire, the below will

happen:

3. The Low tire pressure position

telltale remains illuminated.

• The TPMS malfunction indicator

may blink for approximately 1 minute

and then remain continuously illumi-

nated because the TPMS sensor is

not mounted on the spare wheel.

6-12

TPMS (Tire Pressure

Monitoring System)

malfunction indicator

NOTICE

WARNING

The spare tire is not equipped with

a tire pressure sensor.

Low pressure damage

Significantly low tire pressure

makes the vehicle unstable and

can contribute to loss of vehicle

control and increased braking

distances.

The TPMS malfunction indicator will

illuminate after it blinks for approxi-

mately one minute when there is a

problem with the Tire Pressure

Monitoring System.

CAUTION

In winter or cold weather, the low

tire pressure telltale may illumi-

nate if the tire pressure was

adjusted to the recommended

tire inflation pressure in warm

weather. It does not mean your

TPMS is malfunctioning because

the decreased temperature leads

to a lowering of tire pressure.

Continued driving on low pres-

sure tires can cause the tires to

overheat and fail.

We recommend that the system be

checked by an authorized HYUNDAI

dealer.

NOTICE

If there is a malfunction with the

TPMS, the low tire pressure posi-

tion telltale will not be displayed

even though the vehicle has an

under-inflated tire.

When you drive your vehicle

from a warm area to a cold area

or from a cold area to a warm

area, or the outside temperature

is higher or lower, you should

check the tire inflation pressure

and adjust the tires to the recom-

mended tire inflation pressure.

6

6-13

What to do in an emergency

If you drive the vehicle for about 10

minutes at speeds above 25 km/h

after replacing the low pressure tire

with the spare tire, the below will

happen:

Changing a tire with TPMS

CAUTION

If you have a flat tire, the low Tire

Pressure and Position telltales will

come on. We recommend that the

system be checked by an authorized

HYUNDAI dealer.

• The TPMS malfunction indicator

may blink for approximately 1

minute and then remain contin-

uously illuminated if the vehicle

is moving around electric power

supply cables or radios trans-

mitter such as at police stations,

government and public offices,

broadcasting stations, military

installations, airports, or trans-

mitting towers, etc. This can

interfere with normal operation

of the Tire Pressure Monitoring

System (TPMS).

• The TPMS malfunction indicator

may blink for approximately 1 minute

and then remain continuously illumi-

nated because the TPMS sensor is

not mounted on the spare wheel.

CAUTION

NEVER use a puncture-repair-

ing agent to repair and/or inflate

a low pressure tire. The tire

sealant can damage the tire

pressure sensor. If used, you

will have to replace the tire

pressure sensor.

• The TPMS malfunction indica-

tor may blink for approximate-

ly 1 minute and then remain

continuously illuminated if

snow chains are used or some

separate electronic devices

such as notebook computer,

mobile charger, remote starter

or navigation etc., are used in

the vehicle.

Each wheel is equipped with a tire

pressure sensor mounted inside the

tire behind the valve stem. You must

use TPMS specific wheels. It is rec-

ommended that you have your tires

serviced by an authorized HYUNDAI

dealer.

This can interfere with normal

operation of the Tire Pressure

Monitoring System (TPMS).

6-14

You may not be able identify a low

tire by simply looking at it. Always

use a good quality tire pressure

gauge to measure the tire's inflation

pressure. Please note that a tire that

is hot (from being driven) will have a

higher pressure measurement than a

tire that is cold (from sitting station-

ary for at least 3 hour and driven less

than 1.6 km (1 mile) during that 3

hour period).

WARNING

Tampering with, modifying, or

disabling the Tire Pressure

Monitoring System (TPMS) com-

ponents may interfere with the

system's ability to warn the driv-

er of low tire pressure condi-

tions and/or TPMS malfunctions.

Tampering with, modifying, or

disabling the Tire Pressure

Monitoring System (TPMS) com-

ponents may void the warranty

for that portion of the vehicle.

• The TPMS cannot alert you to

severe and sudden tire dam-

age caused by external factors

such as nails or road debris.

• If you feel any vehicle instabil-

ity, immediately take your foot

off the accelerator, apply the

brakes gradually and with

light force, and slowly move to

a safe position off the road.

Allow the tire to cool before measur-

ing the inflation pressure. Always be

sure the tire is cold before inflating to

the recommended pressure.

A cold tire means the vehicle has

been sitting for 3 hours and driven for

less than 1.6 km (1 mile) in that 3

hour period.

6

6-15

What to do in an emergency

(Continued)

WARNING

❈

All vehicles sold in the

For EUROPE

EUROPE market during below

period must be equipped with

TPMS.

• Do not modify the vehicle; it

may interfere with the TPMS

function.

- New model vehicle :

Nov. 1, 2012 ~

• The wheels on the market do

not have a TPMS sensor.

- Current model vehicle :

Nov. 1, 2014~ (Based on

vehicle registrations)

For your safety, we recom-

mend that you use parts for

replacement from an author-

ized HYUNDAI dealer.

• If you use the wheels on the

market, use a TPMS sensor

approved by a HYUNDAI deal-

er. If your vehicle is not

equipped with a TPMS sensor

or TPMS does not work prop-

erly, you may fail the periodic

vehicle inspection conducted

in your country.

(Continued)

6-16

IF YOU HAVE A FLLAT TIRE (WITH SPARE TIRE, IF EQUIPPED)

Jack and tools

WARNING

Changing a tire can be danger-

ous. Follow the instructions in

this section when changing a

tire to reduce the risk of serious

injury or death.

CAUTION

OTL065005

Be careful as you use the jack

handle to stay clear of the flat

end. The flat end has sharp

edges that could cause cuts.

Turn the winged hold down bolt

counterclockwise to remove the

spare tire.

OTL065004

(1) Jack handle

(2) Jack

Store the spare tire in the same com-

partment by turning the winged hold

down bolt clockwise.

(3) Wheel nut wrench

6

To prevent the spare tire and tools

from "rattling", store them in their

proper location.

The jack, jack handle, and wheel nut

wrench are stored in the luggage

compartment under the luggage box

cover.

The jack is provided for emergency

tire changing only.

6-17

What to do in an emergency

Changing tires

(Continued)

• ALWAYS place the jack on the

designated jacking positions

on the vehicle and NEVER on

the bumpers or any other part

of the vehicle for jacking sup-

port.

WARNING

A vehicle can slip or roll off of a

jack causing serious injury or

death to you or those nearby.

Take the following safety pre-

cautions:

• Do not start or run the engine

while the vehicle is on the

jack.

• Do not get under a vehicle

that is supported by a jack.

OTLE065040

• Do not allow anyone to remain

in the vehicle while it is on the

jack.

• NEVER attempt to change a

tire in the lane of traffic.

ALWAYS move the vehicle

completely off the road on

level, firm ground away from

traffic before trying to change

a tire. If you cannot find a

level, firm place off the road,

call a towing service for assis-

tance.

If it is hard to loosen the tire hold-

down wing bolt by hand, you can

loosen it easily using the jack handle.

• Keep children away from the

road and the vehicle.

1. Put the jack handle (1) inside of

the tire hold-down wing bolt.

2. Turn the tire hold-down wing bolt

counterclockwise with the jack

handle.

• Be sure to use the jack pro-

vided with the vehicle.

(Continued)

6-18

Follow these steps to change your

vehicle’s tire:

1. Park on a level, firm surface.

2. Move the shift lever into P (Park,

for automatic transaxle/dual clutch

transmission vehicle) or neutral (for

manual transaxle vehicle), apply the

parking brake, and place the ignition

switch in the LOCK/OFF position.

3. Press the hazard warning flasher

button.

Block

OTL065012

OTL065013

4. Remove the wheel lug nut wrench,

jack, jack handle, and spare tire

from the vehicle.

5. Block both the front and rear of the 6. Loosen the wheel lug nuts coun-

tire diagonally opposite of the tire

you are changing.

terclockwise one turn each in the

order shown above, but do not

remove any lug nuts until the tire

has been raised off of the ground.

6

6-19

What to do in an emergency

9. Loosen the lug nuts with the wheel

lug nut wrench and remove them

with your fingers. Remove the

wheel from the studs and lay it flat

on the ground out of the way.

Remove any dirt or debris from

the studs, mounting surfaces, and

wheel.

■ Front

■ Rear

10. Install the spare tire onto the

studs of the hub.

11. Tighten the lug nuts with your fin-

gers onto the studs with the

smaller end of the lug nuts clos-

est to the wheel.

OTL065014

OTL065032

7. Place the jack at the designated 8. Insert the jack handle into the jack

jacking position under the frame

closest to the tire you are chang-

ing. The jacking positions are

plates welded to the frame with

two notches and two dimples.

Never jack any other position or

part of the vehicle. It may damage

to the side seal molding.

and turn it clockwise, raising the

vehicle until the tire clears the

ground. Make sure the vehicle is

stable on the jack.

12. Lower the vehicle to the ground

by turning the jack handle coun-

terclockwise.

6-20

If you have a tire gauge, check the

tire pressure (see “Tires and Wheels”

in chapter 8 for tire pressure instruc-

tions.). If the pressure is lower or

higher than recommended, drive

slowly to the nearest service station

and adjust it to the recommended

pressure. Always reinstall the valve

cap after checking or adjusting tire

pressure. If the cap is not replaced,

air may leak from the tire. If you lose

a valve cap, buy another and install it

as soon as possible. After changing

tires, secure the flat tire and return

the jack and tools to their proper stor-

age locations.

CAUTION

Your vehicle has metric threads

on the studs and lug nuts. Make

certain during tire changing

that the same nuts that were

removed are reinstalled. If you

have to replace your lug nuts

make sure they have metric

threads to avoid damaging the

studs and ensure the wheel is

properly secured to the hub. We

recommend that you consult an

authorized HYUNDAI dealer for

assistance.

OTL065007

13. Use the wheel lug nut wrench to

tighten the lug nuts in the order

shown. Double-check each lug

nut until they are tight. After

changing tires, we recommend

that an authorized HYUNDAI

dealer tighten the lug nuts to their

proper torque as soon as possi-

ble. The wheel lug nut should

be tightened to 9~11 kgf·m

(65~79 lbf·ft).

NOTICE

6

If any of the equipment such as the

jack, lug nuts, studs, or other equip-

ment is damaged or in poor condi-

tion, do not attempt to change the

tire and call for assistance.

Check the tire pressure as soon

as possible after installing a spare

tire. Adjust it to the recommended

pressure.

6-21

What to do in an emergency

When driving with the compact spare

tire mounted to your vehicle:

Use of compact spare tires

(if equipped)

NOTICE

When the original tire and wheel

are repaired and reinstalled on the

vehicle, the lug nut torque must be

set correctly. The correct lug nut

tightening torque is 9-11 kgf·m

(65-79 lbf·ft).

• Check the tire pressure after

installing the compact spare tire.

The compact spare tire should be

inflated to 420 kPa (60 psi).

Compact spare tires are designed for

emergency use only. Drive carefully

on the compact spare tire and

always follow the safety precautions.

• Do not take this vehicle through an

automatic car wash while the com-

pact spare tire is installed.

WARNING

• Do not use the compact spare tire

on any other vehicle because this

tire has been designed especially

for your vehicle.

To prevent compact spare tire

failure and loss of control pos-

sibly resulting in an accident:

• Use the compact spare tire

only in an emergency.

• The compact spare tire’s tread life is

shorter than a regular tire. Inspect

your compact spare tire regularly

and replace worn compact spare

tires with the same size and design,

mounted on the same wheel.

• NEVER operate your vehicle

over 80 km/h (50 mph).

• Do not exceed the vehicle’s

maximum load rating or the

load carrying capacity shown

on the sidewall of the com-

pact spare tire.

• Do not use more than one compact

spare tire at a time.

• Do not tow a trailer while the com-

pact spare tire is installed.

• Do not use the compact spare

tire continuously. Repair or

replace the original tire as

soon as possible to avoid fail-

ure of the compact spare tire.

6-22

Jack label

CAUTION

■ Example

To prevent damaging the com-

pact spare tire and your vehicle:

• Drive slowly enough for the

road conditions to avoid all

hazards, such as a potholes

or debris.

• Avoid driving over obstacles.

The compact spare tire diame-

ter is smaller than the diame-

ter of a conventional tire and

reduces the ground clearance

approximately 25 mm (1 inch).

OHYK065011

The actual Jack label in the vehicle may differ from the illustration.

For more detailed specifications, refer to the label attached to the jack.

1. Model Name

8. Shift into Reverse gear on vehicles

with manual transaxle or move the

shift lever to the P position on

vehicles with automatic transaxle/

dual clutch transmission.

• Do not use tire chains on the

compact spare tire. Because

of the smaller size, a tire chain

will not fit properly.

2. Maximum allowable load

6

3. When using the jack, set your

parking brake.

• Do not use the compact spare

tire on any other wheels, nor

should standard tires, snow

tires, wheel covers or trim

rings be used with the com-

pact spare wheel.

4. When using the jack, stop the

engine.

9. The jack should be used on firm

level ground.

5. Do not get under a vehicle that is

supported by a jack.

10. Jack manufacture

11. Production date

6. The designated locations under

the frame

12. Representative company and

address

7. When supporting the vehicle, the

base plate of jack must be vertical

under the lifting point.

6-23

What to do in an emergency

EC Declaration of conformity for Jack

JACKDOC14F

6-24

IF YOU HAVE A FFLAT TIRE (WITH TIRE MOBILITY KIIT, IF EQUIPPED)

Introduction

CAUTION

When two or more tires are flat,

do not use the tire mobility kit

because the supported one

sealant of Tire Mobility Kit is

only used for one flat tire.

WARNING

OTL065033

Do not use the Tire Mobility Kit

to repair punctures in the tire

walls.This can result in an acci-

dent due to tire failure.

For safe operation, carefully read

and follow the instructions in this

manual before use.

OTL065034

With the Tire Mobility Kit you stay

mobile even after experiencing a tire

puncture.

(1) Compressor

(2) Sealant bottle

6

WARNING

The system of compressor and seal-

ing compound effectively and com-

fortably seals most punctures in a

passenger car tire caused by nails

or similar objects and reinflates the

tire.

The Tire Mobility Kit is a temporary

fix to the tire and we recommend that

the system be inspected by an

authorized HYUNDAI dealer.

Have your tire repaired as soon

as possible. The tire may loose

air pressure at any time after

inflating with theTire Mobility Kit.

After you ensured that the tire is

properly sealed you can drive cau-

tiously on the tire (distance up to 200

km (120 miles)) at a max. speed of

80 km/h (50 mph) in order to reach a

service station or tire dealer to have

the tire replaced.

6-25

What to do in an emergency

It is possible that some tires, espe-

cially with larger punctures or dam-

age to the sidewall, cannot be sealed

completely.

Air pressure loss in the tire may

adversely affect tire performance.

For this reason, you should avoid

abrupt steering or other driving

maneuvers, especially if the vehicle

is heavily loaded or if a trailer is in

use.

The Tire Mobility Kit is not designed

or intended as a permanent tire

repair method and is to be used for

one tire only. This instruction shows

you step by step how to temporarily

seal the puncture simply and reliably.

Read the section "Notes on the safe

use of the Tire Mobility Kit".

• Do not use the Tire Mobility Kit if a

tire is severely damaged by driving

run flat or with insufficient air pres-

sure.

Notes on the safe use of the

Tire Mobility Kit

• Park your car at the side of the

road so that you can work with the

Tire Mobility Kit away from moving

traffic.

• Do not remove any foreign objects

such as nails or screws that have

penetrated the tire.

• To be sure your vehicle will not

move, even when you're on fairly

level ground, always set your park-

ing brake.

• Provided the car is outdoors, leave

the engine running. Otherwise

operating the compressor may

eventually drain the car battery.

• Only use the Tire Mobility Kit for

sealing/inflation passenger car

tires. Only punctured areas located

within the tread region of the tire

can be sealed using the tire mobil-

ity kit.

• Never leave the Tire Mobility Kit

unattended while it is being used.

• Do not leave the compressor run-

ning for more than 10 min. at a time

or it may overheat.

• Do not use on motorcycles, bicy-

cles or any other type of tires.

• Do not use the Tire Mobility Kit if

the ambient temperature is below

-30°C (-22°F).

• When the tire and wheel are dam-

aged, do not use Tire Mobility Kit

for your safety.

WARNING

Do not use the TMK if a tire is

severely damaged by driving run

flat or with insufficient air pres-

sure.

• Use of the Tire Mobility Kit may not

be effective for tire damage larger

than approximately 6 mm (0.24 in).

If the tire cannot be made roadwor-

thy with the Tire Mobility Kit, we

recommend that you contact an

authorized HYUNDAI dealer.

Only punctured areas located

within the tread region of the tire

can be sealed using the TMK.

6-26

9. Hose to connect compressor and

sealant bottle or compressor and

wheel

Components of the Tire Mobility Kit

Connectors, cable and connection

hose are stored in the compressor

housing.

WARNING

Expired sealant

Do not use the Tire sealant after

the sealant has expired (i.e.

pasted the expiration date on

the sealant container). This can

increase the risk of tire failure.

6

WARNING

Sealant

OEL069020

• Keep out of reach of children.

• Avoid contact with eyes.

• Do not swallow.

0. Speed- restriction label

4. Holder for the sealant bottle

1. Sealant bottle and label with 5. Compressor

speed restriction

6. On/off switch

2. Filling hose from sealant bottle to

wheel

7. Pressure gauge for displaying the

tire inflation pressure

Strictly follow the specified sequence,

otherwise the sealant may escape

under high pressure.

3. Connectors and cable for the

power outlet direct connection

8. Button for reducing tire inflation

pressure

6-27

What to do in an emergency

Using the Tire Mobility Kit

1. Detach the speed restriction label

(0) from the sealant bottle (1), and

place it in a highly visible place

inside the vehicle such as on the

steering wheel to remind the driv-

er not to drive too fast.

2. Screw connection hose (9) onto

the connector of the sealant bot-

tle.

OTL065036

3. Ensure that button (8) on the com-

pressor is not pressed.

OTL065040

4. Unscrew the valve cap from the

valve of the defective wheel and

screw filling hose (2) of the

sealant bottle onto the valve.

CAUTION

Securely install the sealant fill-

ing hose to the valve. If not,

sealant may flow backward,

possibly clogging the filling

hose.

5. Insert the sealant bottle into the

housing of the compressor (4) so

that the bottle is upright.

OLMF064105

6. Ensure that the compressor is

switched off, position 0.

6-28

8. With the engine start/stop button 9. Switch off the compressor.

position on or ignition switch posi-

10. Detach the hoses from the

tion on, switch on the compressor

sealant bottle connector and

and let it run for approximately

from the tire valve.

5~7 minutes to fill the sealant up

Return the Tire Mobility Kit to its stor-

to proper pressure. (refer to the

age location in the vehicle.

Tire and Wheels, chapter 8). The

inflation pressure of the tire after

filling is unimportant and will be

checked/corrected later.

WARNING

Carbon monoxide

Be careful not to overinflate the

tire and stay away from the tire

when filling it.

OTL065037

Do not leave your vehicle run-

ning in a poorly ventilated area

for extended periods of time.

Carbon monoxide poisoning

and suffocation can occur.

7. Connect between compressor and

the vehicle power outlet using the

cable and connectors.

CAUTION

Tire pressure

WARNING

6

Do not attempt to drive your

vehicle if the tire pressure is

below 29 PSI (200kpa). This

could result in an accident due

to sudden tire failure.

Only use the front passenger

side power outlet when con-

necting the power cord.

6-29

What to do in an emergency

Distributing the sealant

Checking the tire inflation

pressure

CAUTION

Do not exceed a speed of 80

km/h (50 mph). If possible, do

not fall below a speed of 20

km/h (12 mph).

While driving, if you experience

any unusual vibration, ride dis-

turbance or noise, reduce your

speed and drive with caution

until you can safely pull off of

the side of the road.

OLMF064106

Call for road side service or

towing. When you use the Tire

Mobility Kit, the tire pressure

sensors and wheel may be dam-

aged by sealant, remove the

sealant stained with tire pres-

sure sensors and wheel and

inspect in authorized dealer.

OTL065038

11. Immediately drive approximately

7~10 km (4~6 miles or, about

10min) to evenly distribute the

sealant in the tire.

1. After driving approximately 7~10

km (4~6 miles or about 10 min),

stop at a safety location.

2. Connect connection hose (9) of

the compressor directly to the tire

valve.

3. Plug the compressor power cord

into the vehicle power outlet.

4. Adjust the tire inflation pressure to

the recomended tire inflation.

With the ignition swithched on,

proceed as follows.

6-30

- To increase the inflation pres-

sure : Switch on the compres-

sor, position I. To check the cur-

rent inflation pressure setting,

briefly switch off the compressor.

CAUTION

If the inflation pressure is not

maintained, drive the vehicle a

second time, refer to Distributing

the sealant. Then repeat steps 1

to 4.

Tire pressure sensor

The sealant on the tire pressure

sensor and wheel should be

removed when you replace the

tire with a new one and inspect

the tire pressure sensors in

authorized dealer.

WARNING

Use of the TMK may be ineffec-

tual for tire damage larger than

approximately 4 mm (0.16 in).

Do not let the compressor run

for more than 10 minutes, other-

wise the device will overheat

and may be damaged.

We recommend that you contact

an authorized HYUNDAI dealer if

the tire cannot be made road-

worthy with the Tire Mobility Kit.

NOTICE

The pressure gauge may show

higher than actual reading when

the compressor is running. To get

an accurate tire reading, the com-

pressor needs to be turned off.

6

WARNING

The tire inflation pressure must

be at least 220 kPa (32 psi). If it

is not, do not continue driving.

- To reduce the inflation pres-

sure: Press the button 8 on the

compressor.

Call for road side service or tow-

ing.

6-31

What to do in an emergency

❈ Sealant and spare parts can be

obtained and replaced at an author-

ized vehicle or tire dealer. Empty

sealant bottles may be disposed of

at home. Liquid residue from the

sealant should be disposed of by

your vehicle or tire dealer or in

accordance with local waste dispos-

al regulations.

6-32

TOWING

Towing service

On 4WD vehicles, your vehicle must

be towed with a wheel lift and dollies

or flatbed equipment with all the

wheels off the ground.

CAUTION

The 4WD vehicle should never

be towed with the wheels on the

ground. This can cause serious

damage to the transaxle or the

4WD system.

OTL065028

Dollies

On 2WD vehicles, it is acceptable to

tow the vehicle with the rear wheels

on the ground (without dollies) and

the front wheels off the ground.

Dollies

OTL065026

6

If any of the loaded wheels or sus-

pension components are damaged

or the vehicle is being towed with the

front wheels on the ground, use a

towing dolly under the front wheels.

OTL065027

If emergency towing is necessary,

we recommend having it done by an

authorized HYUNDAI dealer or a

commercial tow-truck service.

CAUTION

• Do not tow the vehicle with the

front wheels on the ground as

this may cause damage to the

vehicle.

When being towed by a commercial

tow truck and wheel dollies are not

used, the front of the vehicle should

always be lifted, not the rear.

Proper lifting and towing procedures

are necessary to prevent damage to

the vehicle. The use of wheel dollies

or flatbed is recommended.

• Do not tow with sling-type

equipment. Use wheel lift or

flatbed equipment.

6-33

What to do in an emergency

■ Front

Removable towing hook

WARNING

If your vehicle is equipped with

a rollover sensor, place the igni-

tion switch in the LOCK/OFF or

ACC position when the vehicle

is being towed. The side impact

and curtain air bag may deploy

if the sensor detects the situa-

tion as a rollover.

OTL065022

■ Rear

When towing your vehicle in an

emergency without wheel dollies:

OTL065021

1. Open the tailgate, and remove the

towing hook from the tool case.

1. Place the ignition switch in the

ACC position.

2. Place the shift lever in N (Neutral).

3. Release the parking brake.

OTL065024

CAUTION

2. Remove the hole cover pressing

the lower part of the cover on the

front bumper.

Failure to place the shift lever in

N (Neutral) may cause internal

damage to the transaxle.

3. Install the towing hook by turning it

clockwise into the hole until it is

fully secured.

4. Remove the towing hook and

install the cover after use.

6-34

If towing service is not available in an Always follow these emergency tow-

emergency, your vehicle may be ing precautions:

temporarily towed using a cable or

Emergency towing

■ Front

• Place the ignition switch in the ACC

chain secured to the emergency tow-

position so the steering wheel is not

ing hook at the front (or rear) of the

locked.

vehicle.

• Place the shift lever in N (Neutral).

Use extreme caution when towing

• Release the parking brake.

the vehicle with a cable or chain. A

driver must be in the vehicle to steer

it and operate the brakes.

• Depress the brake pedal with more

force than normal since you will

have reduced braking perform-

ance.

Towing in this manner may be done

only on hard-surfaced roads for a

short distance and at low speeds.

Also, the wheels, axles, power train,

steering and brakes must all be in

good condition.

OTL065023

■ Rear

• More steering effort will be required

because the power steering system

will be disabled.

• Use a vehicle heavier than your

own to tow your vehicle.

6

• The drivers of both vehicles should

communicate with each other fre-

quently.

• Before emergency towing, check

that the hook is not broken or dam-

aged.

OTL065031

If towing is necessary, we recommend

you have it done by an authorized

HYUNDAI dealer or a commercial tow

truck service.

• Fasten the towing cable or chain

securely to the hook.

• Do not jerk the hook. Apply steady

and even force.

6-35

What to do in an emergency

CAUTION

To avoid damage to your vehicle

and vehicle components when

towing:

• Always pull straight ahead

when using the towing hooks.

Do not pull from the side or at

a vertical angle.

• Do not use the towing hooks

to pull a vehicle out of mud,

sand or other conditions from

which the vehicle cannot be

driven out under its own

power.

OTL065029

• Use a towing cable or chain less

than 5 m (16 feet) long. Attach a

white or red cloth (about 30 cm (12

inches) wide) in the middle of the

cable or chain for easy visibility.

• Limit the vehicle speed to

15 km/h (10 mph) and drive

less than 1.5 km (1 mile) when

towing to avoid serious dam-

age to the automatic transaxle.

• Drive carefully so the towing cable

or chain remains tight during towing.

• Before towing, check the automatic

transaxle/dual clutch transmission

for fluid leaks under your vehicle. If

the automatic transaxle fluid is

leaking, flatbed equipment or a

towing dolly must be used.

6-36

EMERGENNCY COMMODITY (IF EQQUIPPED)

Your vehicle is equipped with emer-

gency commodities to help you

respond to emergency situation.

To check the tire pressure, take the

following steps:

First aid kit

Supplies for use in giving first aid

such as scissors, bandage and

adhesive tape, etc. are provided.

1. Unscrew the inflation valve cap

that is located on the rim of the

tire.

Fire extinguisher

2. Press and hold the gauge against

the tire valve. Some air will leak as

you begin and more will leak if you

don't press the gauge in firmly.

If there is small fire and you know how

to use the fire extinguisher, follow

these steps carefully.

Triangle reflector

Place the triangle reflector on the

road to warn oncoming vehicles dur-

ing emergencies, such as when the

vehicle is parked by the roadside due

to problems.

1. Pull out the safety pin at the top of

the extinguisher that keeps the han-

dle from being accidentally pressed.

3. A firm non-leaking push will acti-

vate the gauge.

4. Read the tire pressure on the gauge

to see whether the tire pressure is

low or high.

2. Aim the nozzle towards the base

of the fire.

Tire pressure gauge

(if equipped)

3. Stand approximately 2.5 m (8 ft)

away from the fire and squeeze

the handle to discharge the extin-

guisher. If you release the handle,

the discharge will stop.

5. Adjust the tire pressure to the

specified pressure. Refer to “Tires

and Wheels” in chapter 8.

Tires normally lose some air in day-

to-day use, and you may have to add

a air periodically and usually it is not

a sign of a leaking tire, but of normal

wear. Always check tire pressure

when the tires are cold because tire

pressure increases with temperature.

6

6. Reinstall the inflation valve cap.

4. Sweep the nozzle back and forth

at the base of the fire. After the fire

appears to be out, watch carefully

since it may re-ignite.

6-37

What to do in an emergency

ERA-GLONASS EMERGENCYY CALL (IF EEQUIPPED)

The car is equipped with a device*

connected with the system ERA-

GLONASS for making emergency

call to response teams. The system

ERA-GLONASS is an automatic

emergency call service made in

event of a traffic accident or other**

accidents on the roads of Russian

Federation.

The system allows contacting with

an officer of the single duty dispatch

service in case of accidents on the

roads of Russian Federation. The

system ERA-GLONASS given condi-

tions, stated in the Owner’s Manual

as well as Warranty and Service

book transmits data to the single

duty dispatch service, including such

information as vehicle location, vehi-

ETL-001

cle type, VIN (vehicle identification

number of the car).

➀ Road accident

➁ Wireless network

➂ Single duty dispatch service (SDDS)

➃ Rescue

* ERA-GLONASS device in the Owner's Manual means equipment, installed in the car, which provides connection with the ERA-GLONASS system.

** "Other accidents' mean any accidents on the roads of Russian Federation resulted in injured people and/or necessity of provision of assistance.

In case of registration of any accident, it is necessary to stop a vehicle, press button SOS (location of the button is specified on the picture in the

chapter "ERA-GLONASS EMERGENCY CALL (IF EQUIPPED)") of the Owner’s Manual. When making a call, the system gathers information

about the car (from which a call was made), after which connects the car with an officer of the single duty dispatch service to tell about the rea-

son of the emergency call.

6-38

Once the data which stored in the

ERA-GLONASS system is delivered

to the rescue center to assist the

driver and passengers with proper

rescue operations, the data will be

deleted after rescue operation is

completed.

SOS button: the driver/passenger

makes an emergency call to the sin-

gle duty dispatch service by pressing

the button.

ERA-GLONASS system

SOS TEST button (test): the button

is to check working ability of the sys-

tem in the official dealership of

Hyundai.The mode "SOS TEST" can

be activated strictly by the specialist

of the authorized dealership of

Hyundai. To avoid erroneous calls,

please, do not press this button and

do not activate the mode "SOS

TEST" by yourself.

Operator of the system ERA-

GLONASS

(stock

company

"GLONASS") is responsible for all

components of the system ERA-

GLONASS (excluding equipment,

installed in the car) in accordance with

the federal law "On state automated

information system ERA-GLONASS"

# 395-FZ from 28.12.2013.

ETL-004

Elements of the system ERA-

GLONASS, installed in passenger

compartment:

LED: The red and green LED illumi-

nates for 3 seconds when the ignition

switch is in the ON position. After that

they will switch off at normal opera-

tion of the system.

6

➀ Microphone

➁ SOS button

➂ SOS TEST button

➃ LED

If there are some problems in the

system, the LED remains in red.

6-39

What to do in an emergency

Automatic accident reporting

i

Information

System operation in the

event of a traffic accident

Connection with the single

duty dispatch service

Emergency services

In even of minor traffic accidents the

ERA-GLONASS system may not exe-

cute an emergency call. However, an

emergency call may be made manual-

ly by pressing the SOS button.

CAUTION

ETL-002

Operation of the system is

impossible in case of absence

of mobile transmission and

GPS and GLONASS signals.

The ERA-GLONASS device automatically makes an emergency call to the sin-

gle duty dispatch service for proper rescuing operations in event of car acci-

dent.

For proper emergency services and support the ERA-GLONASS system auto-

matically transmits the accident data to the single duty dispatch service when

a traffic accident is detected.

In this case, the emergency call cannot be hung up by pressing the SOS but-

ton and the ERA-GLONASS system remains connected until the emergency

service officer, receiving the call, disconnects the emergency call.

6-40

Manual accident reporting

1. Stop a car, after which in accor-

dance with traffic rules to ensure

safety to yourself and other partic-

ipants of road traffic;

Connection with the single

duty dispatch service

Pressing the SOS button

Emergency services

2. Press the SOS button, when

pressing the button SOS registra-

tion of the device in the wireless

telephonic communication net-

works is carried out, minimum

data set about car and its location

is collected in accordance with of

the technical requirements of the

device. After that connection with

the officer of the ERA-GLONASS

system is made for clearing up

reasons (conditions) of the emer-

gency call.

ETL-003

Driver or passenger manually can make an emergency call in the single duty

dispatch service, by pressing SOS button to call the necessary emergency

services.

A call to the emergency services through the ERA-GLONASS system can be

cancelled by pressing the SOS button again only before the call connection.

6

After activation of emergency call in the manual mode (for proper emergency

services and support), the ERA-GLONASS system automatically transmits the

road accident data / or data on other accident to the officer of the single duty

dispatch service (during emergency call) by pressing the SOS button.

3. After clearing up reasons of the

emergency call, the officer of the

single duty dispatch service sends

minimum data set to emergency

services and completes the emer-

gency call.

In case of road accident or other accident for activation of emergency call in

manual mode it is necessary:

If the emergency call is not carried

out in accordance with the proce-

dure, mentioned above, the emer-

gency call will be considered as erro-

neous.

6-41

What to do in an emergency

(Continued)

WARNING

LED illumination in red (system

malfunction)

Arbitrary

Modification

Removal

or

Emergency power supply of the

system ERA-GLONASS from

the battery

If red LED illuminates in normal

driving conditions, this can

indicate malfunction of the

ERA-GLONASS system. Please,

have the ERA-GLONASS sys-

tem checked at an authorized

Hyundai dealership immediate-

ly. Otherwise correct operation

of the ERA-GLONASS system

device, installed in your car is

not guaranteed. Owner of the

car incurs liability for conse-

quences, occurred as a result of

nonobservance of conditions,

mentioned above.

The ERA-GLONASS system

calls emergency services for

assistance. Thus, any arbitrary

removal or changes to the ERA-

GLONASS system settings may

affect your driving safety. Also,

it may even make an erroneous

emergency call to the single

duty dispatch service. Thereby,

we kindly ask you not to make

any changes by yourself or by

the third parties in the settings

of the equipment of the ERA-

GLONASS system, installed in

your car.

• The ERA-GLONASS system

battery supplies power during

1 hour in case main power

source of the vehicle is cut off

due to the collision during the

emergency situations.

• The ERA-GLONASS system

battery should be replaced

every 3 years. For more infor-

mation

refer

to

the

Maintenance Schedule in

chapter 7.

(Continued)

6-42

There is a technical opportunity to You can start the ERA-GLONASS

check working ability of the ERA- test mode by pressing the SOS

GLONASS device, installed in your TEST button. The test mode starts

car. In order to avoid making erro- with a voice guidance to check work-

neous calls and incorrect operation ing ability of the ERA-GLONASS

of the device, checking of the ERA- device. In the course of checking

GLONASS device, installed in your working ability of the ERA-

car, should be carried out only by GLONASS device red and green

specialists of authorized Hyundai LED illuminate.

Test Mode

dealerships and on their territory in

Re-press the SOS TEST button

accordance with the following manu-

again to deactivate the test mode

al (on applying user interface for

during the voice guidance.

launching test mode).

ETL-005

Elements of the system ERA-

GLONASS, installed in passenger

compartment:

6

➀ Microphone

➁ SOS button

➂ SOS TEST button

➃ LED

6-43

What to do in an emergency for Your Hyundai Tucson SUV Third Generation (2016-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals