2013-2018 Kia Ceed SUV Features of your vehicle -> Audio system User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Features of your vehicle -> Audio system for Your Kia Ceed SUV Second Generation (2013-2018)

JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 172  
Features of your vehicle  
AUDIO SYSTEM  
✽
NOTICE  
CAUTION  
• If you install an aftermarket HID  
head lamp, your vehicle’s audio and  
electronic device may malfunction.  
• Prevent chemicals such as perfume,  
cosmetic oil, sun cream, hand cleaner,  
and air freshener from contacting the  
interior parts because they may cause  
damage or discoloration.  
• Before entering a place with a low  
height clearance or a car wash,  
remove the antenna by rotating it  
counterclockwise. If not, the  
antenna may be damaged.  
• When reinstalling your antenna, it  
is important that it is fully tight-  
ened and adjusted to the upright  
position to ensure proper recep-  
tion. But it could be removed  
when parking the vehicle or when  
loading cargo on the roof rack.  
OHM048154N  
Antenna  
• When cargo is loaded on the roof  
rack, do not place the cargo near  
the antenna pole to ensure proper  
reception.  
Roof antenna  
Your car uses a roof antenna to receive  
both AM and FM broadcast signals. This  
antenna is a removable type. To remove  
the antenna, turn it counterclockwise. To  
install the antenna, turn it clockwise.  
4 172  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 173  
Features of your vehicle  
■ Type A  
RADIO mode  
It will function as the PRESET STATION  
select buttons.  
VOL (+ / -) (1)  
• Push up the lever to increase volume.  
• Push down the lever to decrease vol-  
ume.  
CDP mode  
It will function as the TRACK UP/DOWN  
button.  
SEEK (  
/
) (2)  
The SEEK/PRESET button has different  
functions base on the system mode. For  
the following functions the button should  
be pressed for 0.8 seconds or more.  
Detailed information for audio control  
buttons are described in the following  
pages in this section.  
OJD042147  
■ Type B  
RADIO mode  
It will function as the AUTO SEEK select  
button.  
MUTE (3)  
• Press the MUTE button to cancel the  
sound.  
• Press the MUTE button again to acti-  
vate the sound.  
CDP mode  
It will function as the FF/REW button.  
MODE (4)  
Press the button to select Radio or CD  
(compact disc).  
If the SEEK button is pressed for less  
than 0.8 second, it will work as follows in  
each mode.  
OJD042149  
Audio remote control  
(if equipped)  
The steering wheel audio remote control  
button is installed to promote safe driving.  
CAUTION  
Do not operate the audio remote  
control buttons simultaneously.  
4 173  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 174  
Features of your vehicle  
FM reception  
AM reception  
FM radio station  
JBM001  
JBM002  
JBM003  
AM broadcasts can be received at  
greater distances than FM broadcasts.  
This is because AM radio waves are  
transmitted at low frequencies. These  
long, low frequency radio waves can fol-  
low the curvature of the earth rather than  
travelling straight out into the atmos-  
phere. In addition, they curve around  
obstructions so that they can provide bet-  
ter signal coverage.  
FM broadcasts are transmitted at high  
frequencies and do not bend to follow the  
earth's surface. Because of this, FM  
broadcasts generally begin to fade at  
short distances from the station. Also,  
FM signals are easily affected by build-  
ings, mountains, or other obstructions.  
These can result in certain listening con-  
ditions which might lead you to believe a  
problem exists with your radio. The fol-  
lowing conditions are normal and do not  
indicate radio trouble:  
How car audio works  
AM and FM radio signals are broadcast  
from transmitter towers located around your  
city.They are intercepted by the radio anten-  
na on your car. This signal is then received  
by the radio and sent to your car speakers.  
When a strong radio signal has reached  
your vehicle, the precise engineering of  
your audio system ensures the best pos-  
sible quality reproduction. However, in  
some cases the signal coming to your  
vehicle may not be strong and clear. This  
can be due to factors such as the dis-  
tance from the radio station, closeness of  
other strong radio stations or the pres-  
ence of buildings, bridges or other large  
obstructions in the area.  
4 174  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 175  
Features of your vehicle  
Using a cellular phone or a two-way  
radio  
When a cellular phone is used inside the  
vehicle, noise may be produced from the  
audio equipment. This does not mean  
that something is wrong with the audio  
equipment. In such a case, use the cellu-  
lar phone at a place as far as possible  
from the audio equipment.  
CAUTION  
When using a communication sys-  
tem such a cellular phone or a radio  
set inside the vehicle, a separate  
external antenna must be fitted.  
When a cellular phone or a radio set  
is used with an internal antenna  
alone, it may interfere with the vehi-  
cle's electrical system and adverse-  
ly affect safe operation of the vehi-  
cle.  
JBM004  
JBM005  
• Fading - As your car moves away from  
the radio station, the signal will weaken  
and sound will begin to fade. When this  
occurs, we suggest that you select  
another stronger station.  
• Station Swapping - As a FM signal  
weakens, another more powerful sig-  
nal near the same frequency may  
begin to play. This is because your  
radio is designed to lock onto the clear-  
est signal. If this occurs, select another  
station with a stronger signal.  
• Flutter/Static - Weak FM signals or  
large obstructions between the trans-  
mitter and your radio can disturb the  
signal causing static or fluttering nois-  
es to occur. Reducing the treble level  
may lessen this effect until the distur-  
bance clears.  
• Multi-Path Cancellation - Radio signals  
being received from several directions  
can cause distortion or fluttering. This  
can be caused by a direct and reflect-  
ed signal from the same station, or by  
signals from two stations with close  
frequencies. If this occurs, select  
another station until the condition has  
passed.  
WARNING  
Don't use a cellular phone when  
you are driving. You must stop at a  
safe place to use a cellular phone.  
4 175  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 176  
Features of your vehicle  
(Continued)  
CAUTION  
WARNING  
• Do not touch the antenna during  
thunder or lightening as such  
acts may lead to lightning  
induced electric shock.  
• Operating the device while driv-  
ing could lead to accidents due to  
a lack of attention to external sur-  
roundings. First park the vehicle  
before operating the device.  
• Do not stare at the screen while  
driving. Staring at the screen for  
prolonged periods of time could  
lead to traffic accidents.  
• Do not stop or park in parking-  
restricted areas to operate the  
product. Such acts could lead to  
traffic accidents.  
• Do not disassemble, assemble, or  
modify the audio system. Such  
acts could result in accidents,  
fire, or electric shock.  
• Adjust the volume to levels that  
allow the driver to hear sounds  
from outside of the vehicle.  
Driving in a state where external  
sounds cannot be heard may lead  
to accidents.  
• Use the system with the vehicle  
ignition turned on. Prolonged use  
with the ignition turned off could  
result in battery discharge.  
• Using the phone while driving may  
lead to a lack of attention of traffic  
conditions and increase the likeli-  
hood of accidents.  
phone feature after parking the  
vehicle.  
• Pay attention to the volume set-  
ting when turning the device on.  
A sudden output of extreme vol-  
ume upon turning the device on  
could lead to hearing impairment.  
(Adjust the volume to a suitable  
levels before turning off the  
device.)  
Use  
the  
• Heed caution not to spill water or  
introduce foreign objects into the  
device. Such acts could lead to  
smoke, fire, or product malfunc-  
tion.  
• If you want to change the position  
of device installation, please  
inquire with your place of pur-  
chase or service maintenance  
center. Technical expertise is  
required to install or disassemble  
the device.  
• Please refrain from use if the  
screen is blank or no sound can  
be heard as these signs may indi-  
cate product malfunction.  
Continued use in such conditions  
could lead to accidents(fires,  
electric shock) or product mal-  
functions.  
(Continued)  
(Continued)  
4 176  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 177  
Features of your vehicle  
(Continued)  
(Continued)  
• Turn on the car ignition before  
using this device. Do not operate  
the audio system for long periods  
of time with the ignition turned off  
as such operations may lead to  
battery discharge.  
• In case of product malfunction,  
please contact your place of pur-  
chase or After Service center.  
• Placing the audio system within  
an electromagnetic environment  
may result in noise interference.  
• Do not subject the device to  
severe shock or impact. Direct  
pressure onto the front side of  
the monitor may cause damage to  
the LCD or touch screen.  
• When cleaning the device, make  
sure to turn off the device and  
use a dry and smooth cloth.  
Never use tough materials, chem-  
ical cloths, or solvents (alcohol,  
benzene, thinners, etc.) as such  
materials may damage the device  
panel or cause color/quality dete-  
rioration  
• Do not place beverages close to  
the audio system. Spilling bever-  
ages may lead to system mal-  
function.  
(Continued)  
4 177  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 178  
Features of your vehicle  
2. Folder playing order :  
❋ If no song file is contained in the fold-  
er, that folder is not displayed.  
Caring for disc  
✽
NOTICE - Playing an  
Incompatible Copy  
Protected Audio CD  
• If the temperature inside the car is too  
high, open the car windows to ventilate  
before using the system.  
Some copy protected CDs, which do not  
comply with international audio CD  
standards (Red Book), may not play on  
your car audio. Please note that inabili-  
ties to properly play a copy protected  
CD may indicate that the CD is defec-  
tive, not the CD player.  
• It is illegal to copy and use MP3/WMA  
files without permission. Use CDs that  
are created only by lawful means.  
• Do not apply volatile agents, such as  
benzene and thinner, normal cleaners  
and magnetic sprays made for ana-  
logue disc onto CDs.  
• To prevent the disc surface from get-  
ting damaged, hold CDs by the edges  
or the center hole only.  
✽
NOTICE  
Order of playing files (folders) :  
1. Song playing order :  
tially.  
to  
sequen-  
• Clean the disc surface with a piece of  
soft cloth before playback (wipe it from  
the center to the outside edge).  
• Do not damage the disc surface or  
attach pieces of sticky tape or paper.  
• Make certain only CDs are inserted  
into the CD player (Do not insert more  
than one CD at a time).  
• Keep CDs in their cases after use to  
protect them from scratches or dirt.  
• Depending on the type of CD-R/CD-  
RW CDs, certain CDs may not operate  
normally according to manufacturing  
companies or making and recording  
methods. In such circumstances, con-  
tinued use may cause malfunctions to  
your audio system.  
4 178  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 179  
Features of your vehicle  
• Depending on the condition of the  
• Depending on the type and capacity of  
the external USB device or the type of  
the files stored in the device, there is a  
difference in the time taken for recogni-  
tion of the device.  
Using Your USB Device  
external USB device, the connected  
external USB device can be unrec-  
ognizable.  
• To use an external USB device,  
make sure the device is not connect-  
ed when starting up the vehicle.  
Connect the device after starting up.  
• When the formatted byte/sector set-  
ting of External USB device is not  
either 512BYTE or 2048BYTE, then  
the device will not be recognized.  
• Do not use the USB device for purposes  
other than playing music files.  
• If you start the engine when the USB  
device is connected, it may damage  
the USB device. (USB flashdrives  
are very sensitive to electric shock.)  
• Playing videos through the USB is not  
supported.  
• Use only a USB device formatted to  
FAT 12/16/32.  
• Use of USB accessories such as  
rechargers or heaters using USB I/F  
may lower performance or cause  
trouble.  
• If the engine is started up or turned  
off while the external USB device is  
connected, the external USB device  
may not work.  
• USB devices without USB I/F authen-  
tication may not be recognizable.  
• Make sure the USB connection termi-  
nal does not come in contact with the  
human body or other objects.  
• If you use devices such as a USB  
hub purchased separately, the vehi-  
cle’s audio system may not recog-  
nize the USB device. In that case,  
connect the USB device directly to  
the multimedia terminal of the vehi-  
cle.  
• It may not play inauthentic MP3 or  
WMA files.  
1) It can only play MP3 files with the  
• If you repeatedly connect or discon-  
nect the USB device in a short peri-  
od of time, it may break the device.  
compression  
8Kbps~320Kbps.  
rate  
between  
• You may hear a strange noise when  
connecting or disconnecting a USB  
device.  
2) It can only play WMA music files  
with the compression rate  
between 8Kbps~320Kbps.  
• If the USB device is divided by logi-  
cal drives, only the music files on the  
highest-priority drive are recognized  
by car audio.  
• If you disconnect the external USB  
device during playback in USB mode,  
the external USB device can be dam-  
aged or may malfunction. Therefore,  
disconnect the external USB device  
when the audio is turned off or in  
another mode. (e.g, Radio, CD)  
• Take precautions for static electricity  
when connecting or disconnecting the  
external USB device.  
• Devices such as MP3 Player/  
Cellular phone/Digital camera can be  
unrecognizable by standard USB I/F  
can be unrecognizable.  
• An encrypted MP3 PLAYER is not  
recognizable.  
(Continued)  
4 179  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 180  
Features of your vehicle  
✽
NOTICE - USB Jack Damage  
(Continued)  
• Charging through the USB may not  
be supported in some mobile  
devices.  
• The data in the USB memory may be  
lost while using this audio.  
Always back up important data on a  
personal storage device.  
• Please avoid using USB memory prod-  
ucts which can be used as key chains  
or cellular phone accessories as they  
could cause damage to the USB jack.  
Please make certain only to use plug  
type connector products as shown  
below.  
• USB HDD or USB types that liable to  
connection failures due to vehicle  
vibrations are not supported. (i-stick  
type)  
• Some non-standard USB devices  
(METAL COVER TYPE USB) can be  
unrecognizable.  
• Some USB flash memory readers  
(such as CF, SD, micro SD, etc.) or  
external-HDD type devices can be  
unrecognizable.  
• Music files protected by DRM (DIGI-  
TAL RIGHTS MANAGEMENT) are  
not recognizable.  
4 180  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 181  
Features of your vehicle  
■ CD Player : AC110A2EE/AC100A2EE  
❋No  
logo will be shown if the Bluetooth® Wireless Technology feature is not supported.  
4 181  
JD eng 4b(~211).QXP 3/12/2015 3:03 PM Page 182  
Features of your vehicle  
When the pop up screen is displayed,  
1
use the  
6
TUNE knob or keys  
to select the desired mode.  
~
MEDIA  
(3)  
Changes to CD, USB MP3, iPod, BT  
MP3, AUX modes.  
Each time the key is pressed, the mode  
is changed in order of CD, USB, iPod,  
AUX, My Music, BT Audio.  
❈ In Setup>Display, the media pop up  
screen will be displayed when [Mode  
On  
Pop up] is turned  
.
SYSTEM CONTROLLERS AND  
FUNCTIONS  
(6)  
/
knob  
Power Knob: Turns power On/Off by  
When the pop up screen is displayed,  
1
use the  
5
TUNE knob or keys  
to select the desired mode.  
~
pressing the knob  
Volume Knob: Sets volume by turning  
the knob left/right  
❈ Display and settings may differ  
depending on the selected audio.  
PHONE  
(4)  
Operates Phone Screen  
FM  
(7)  
Changes to FM mode.  
Audio Head Unit  
❈ When a phone is not connected, the  
connection screen is displayed.  
(1) (EJECT)  
Ejects the disc.  
Each time the key is pressed, the mode is  
changed in order of FM1  
SEEK  
TRACK  
➟
FM2  
➟
FMA.  
(5)  
,
Radio Mode : Automatically searches for  
broadcast frequencies.  
RADIO  
(2)  
Changes to FM/AM mode.  
AM  
(8)  
Changes to AM mode.  
CD, USB, iPod, My Music modes  
Each time the key is pressed,the mode is  
changed in order of FM1 ➟ FM2 ➟ FMA  
➟ AM ➟ AMA.  
- Shortly press the key (under 0.8 seconds):  
Moves to next or previous song (file)  
Each time the key is pressed, the mode  
is changed in order of AM ➟ AMA.  
- Press and hold the key (over 0.8 seconds):  
Rewinds or fast-forwards the current song.  
❈ In Setup>Display, the radio pop up  
screen will be displayed when [Mode  
Pop up] is turned  
.
On  
4 182  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 183  
Features of your vehicle  
SETUP  
(14)  
Press the  
(11)  
Each time the button is pressed sets  
screen Off ➟ Screen On ➟ Screen Off  
SETUP  
key : Moves to the  
Display, Sound, Phone(Option), System  
setting modes  
❈ Audio operation is maintained and  
only the screen will be turned Off.  
In the screen Off state, press any key  
to turn the screen On again.  
TA/SCAN  
(12)  
Radio Mode  
- Press and hold the key (over 0.8 sec-  
onds): Previews each broadcast for 5  
seconds each  
❈ If the Bluetooth® Wireless Technology  
feature is supported  
1
6
(9)  
(Preset)  
~
CD, USB, iPod mode  
Radio Mode: Saves frequencies (chan-  
nels) or receives saved frequencies  
(channels)  
- Press and hold the key (over 0.8 sec-  
onds): Previews each song (file) for 10  
seconds each  
CD, USB, iPod, My Music mode  
TA/SCAN  
❈ Press the  
key (over 0.8  
RPT  
1
-
-
: Repeat  
: Random  
seconds) again to continue listening to  
the current song (file).  
RDM  
2
In the Radio, Media, Setup, and Menu  
pop up screen, the number menu is  
selected.  
(15)  
TUNE knob  
MEMU  
(13)  
Displays menus for the current mode.  
Radio mode : Changes frequency by  
turning the knob left/right  
PTY  
FOLDER  
(10)  
,
CD, USB, iPod mode: Searches songs  
(files) by turning the knob left/right  
❈ When the desired song is displayed,  
MP3, CD, USB mode : Folder Search  
FM : RDS Program Type Search  
press the knob to play the song.  
Moves focus in all selection menus and  
selects menus  
4 183  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 184  
Features of your vehicle  
Mode Pop up  
DISPLAY SETTINGS  
SOUND SETTINGS  
On  
[Mode Pop up] Changes  
selection mode  
SETUP  
Press the  
through  
key Select [Sound]  
RDM  
2
TUNE knob or  
key  
RADIO  
• During On state, press the  
MEDIA  
or  
key to display the mode  
Select menu through  
TUNE knob  
change pop up screen.  
Scroll Text  
SETUP  
Press the  
through  
key Select [Display]  
On  
Off  
[Scroll Text] Set  
/
RPT  
1
TUNE knob or  
key  
On  
•
•
: Maintains scroll  
: Scrolls only one (1) time.  
Select menu through  
TUNE knob  
Off  
Song Info  
When playing an MP3 file, select the  
desired display info from ‘Folder/File’ or  
‘Album/Artist/Song’.  
4 184  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 185  
Features of your vehicle  
Audio Settings  
Power Bass  
Volume Dialogue  
This menu allows you to set the ‘Bass,  
Middle, Treble’ and the Sound Fader and  
Balance.  
This is a sound system feature that pro-  
vides live bass.  
Adjusts voice recognition volume.  
Select [Volume Dialogue] Set vol-  
ume of  
On  
Off  
Select [Power Bass] Set  
through TUNE knob  
/
TUNE knob  
Select [Audio Settings] Select menu  
through TUNE knob Turn  
TUNE knob left/right to set  
• Bass, Middle, Treble : Selects the sound  
tone.  
• Fader, Balance : Moves the sound fader  
and balance.  
• Default : Restores default settings.  
Speed Dependent Volume Control  
❈ Return : While adjusting values, re-  
pressing the TUNE knob will  
restore the parent menu.  
This feature is used to automatically con-  
trol the volume level according to the  
speed of the vehicle.  
Select [SDVC] Set in 4 levels [Off/  
Low/Mid/High] of  
TUNE knob  
4 185  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 186  
Features of your vehicle  
❈ It is possible to pair up to five  
Bluetooth® Wireless Technology  
enabled mobile phones.  
Pair Phone  
®
To pair a Bluetooth Wireless Technology  
enabled mobile phone, authentication  
and connection processes are first  
required. As a result, you cannot pair  
your mobile phone while driving the vehi-  
cle. First park your vehicle before use.  
PHONE SETUP (if equipped)  
SETUP  
Press the  
key Select [Phone]  
3
through  
TUNE knob or  
key  
Select menu through  
TUNE knob  
Select [Pair Phone] Set through TUNE  
knob  
➀ Search for device names as displayed  
on your mobile phone and connect.  
➁ Input the passkey displayed on the  
screen. (Passkey : 0000)  
❈ The device name and passkey will be  
displayed on the screen for up to 3  
minutes. If pairing is not completed  
within the 3 minutes, the mobile phone  
pairing process will automatically be  
canceled.  
➂ Pairing completion is displayed.  
❈ In some mobile phones, pairing will  
automatically be followed by connection.  
4 186  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 187  
Features of your vehicle  
Changing connection sequence  
(Priority)  
Phone List  
➂ Connection completion is displayed.  
❈ If a phone is already connected, dis-  
connect the currently connected  
phone and select a new phone to con-  
nect.  
The names of up to 5 paired phones will  
be displayed.  
This is used to change the order (priori-  
ty) of automatic connection for the paired  
mobile phones.  
A [ ] is displayed in front of the currently  
connected phone.  
Select [Phone List] Select mobile  
Disconnecting a connected phone  
phone through  
[Priority]  
TUNE knob Select  
Select [Phone List] Select mobile  
phone through  
TUNE knob Select  
[Disconnect Phone]  
➀ Select [ Phone] in the [Setup]  
➁ Select [Phone List]  
➂ From the paired phones, select the  
➀ Select the currently connected mobile  
phone.  
Select the desired name to setup the  
selected phone.  
phone desired for No.1 priority.  
Select [  
Priority]  
Connecting a phone  
❈ Once the connection sequence (priori-  
ty) is changed, the new no. 1 priority  
mobile phone will be connected.  
Select [Phone List] Select mobile  
phone through  
TUNE knob Select  
[Connect Phone]  
- when the no. 1 priority cannot be con-  
nected: Automatically attempts to con-  
nect the most recently connected  
phone.  
➁ Disconnect the selected mobile  
phone.  
➂ Disconnection completion is dis-  
played.  
- Cases when the most recently con-  
nected phone cannot be connected:  
Attempts to connect in the order in  
which paired phones are listed.  
➀ Select a mobile phone that is not cur-  
rently connected.  
➁ Connect the selected mobile phone.  
4 187  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 188  
Features of your vehicle  
Delete  
Phone book Download  
Audio Streaming  
Songs (files) saved in your Bluetooth®  
Wireless Technology enabled mobile phone  
can be played through the audio system.  
Select [Phone List] Select mobile  
This feature is used to download a phone  
book and call histories into the audio sys-  
tem.  
phone through  
[Delete]  
TUNE knob Select  
On  
Select [Phone] Select [  
[
History] Select [Audio Streaming] Set  
Off  
/
P.BOOK] through  
TUNE knob  
through  
TUNE knob  
➀ Select the desired mobile phone.  
➁ Delete the selected mobile phone.  
➂ Deletion completion is displayed.  
®
•
The download feature may not be support-  
ed in some mobile phones.  
•
The Bluetooth Wireless Technology  
audio streaming feature may not be sup-  
ported in some mobile phones.  
❈ When attempting to delete a currently  
connected phone, the phone is first  
disconnected.  
• If a different operation is performed while  
a phone book is being downloaded,  
downloading will be discontinued. The  
phone book already downloaded will be  
saved.  
Outgoing Volume  
• When you delete a mobile phone, lt's  
phone book will also be erased.  
• For stable Bluetooth® Wireless Technology  
communication, delete the mobile phone  
from the audio and also delete the audio  
from your mobile phone  
This is used to set the volume of your  
voice as heard by the other party while  
on a Bluetooth® Wireless Technology  
enabled handsfree call.  
• When downloading a new phone book,  
delete all previously saved phone book  
before starting download.  
Select [Outgoing Volume] Set vol-  
TUNE knob  
ume through  
Auto Download  
When connecting a mobile phone, it is  
possible to automatically download a  
new phone book and Call Histories.  
On  
Select [Auto Download] Set  
/
Off  
through  
TUNE knob  
4 188  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 189  
Features of your vehicle  
Bluetooth® Wireless Technology  
System Off  
• Turning On Bluetooth® Wireless  
Bluetooth® Wireless Technology con-  
nection may become intermittently discon-  
nected in some mobile phones. Follow  
these next steps to try again.  
SETUP  
Technology through the  
Key  
SETUP  
Press the  
through  
key Select [Phone]  
This feature is used when you do not  
wish to use the Bluetooth® Wireless  
Technology system.  
Select [Bluetooth® Wireless Technology  
3
TUNE knob or  
key  
1) Turn the Bluetooth® Wireless Technology  
function within the mobile phone  
ON/OFF and try to connect again.  
➀ A screen asking whether to turn on  
Bluetooth® Wireless Technology will be  
displayed.  
System Off] Set through  
knob  
TUNE  
2) Turn the mobile phone power ON/OFF and  
try to connect again.  
YES  
➁ On the screen, select  
to turn on  
Bluetooth® Wireless Technology and  
display guidance.  
3) Completely remove the mobile phone  
battery, reboot, and then try to connect  
again.  
❈ If a phone is already connected, dis-  
connect the currently connected phone  
and turn the Bluetooth® Wireless  
Technology system off.  
❈ If the Bluetooth® Wireless Technology  
system is turned on, the system will  
automatically try to connect the most  
4) Reboot the audio system and try to con-  
nect again  
5) Delete all paired devices in your mobile  
phone and the audio system and pair  
again for use.  
recently  
connected  
Bluetooth®  
Using the Bluetooth® Wireless  
Technology System  
Wireless Technology mobile phone.  
To use Bluetooth® Wireless Technology  
when the system is currently off, follow  
these next steps.  
• Turning On Bluetooth® Wireless  
PHONE  
Technology through the  
Key  
PHONE  
Press the  
key Screen Guidance  
❈ Moves to the screen where Bluetooth®  
Wireless Technology functions can be  
used and displays guidance.  
4 189  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 190  
Features of your vehicle  
VRS Mode  
SYSTEM SETTINGS  
This feature is used to change voice  
command feedback between Normal and  
Expert modes.  
If the Bluetooth® Wireless Technology  
feature is supported  
Select [VRS Mode] Set through  
TUNE knob  
SETUP  
Press the  
key Select [  
4
System] through tune knob or  
key Select menu through  
knob  
• Normal : This mode is for beginner  
users and provides detailed instructions  
during voice command operation.  
TUNE  
Memory Information  
• Expert : This mode is for expert users  
and omits some information during  
voice command operation. (When using  
Expert mode, guidance instructions can  
be heard through the [Help] or [Menu]  
commands.  
If the Bluetooth® Wireless Technology  
feature is not supported  
Displays currently used memory and  
total system memory.  
Select [Memory Information] OK  
The currently used memory is displayed  
on the left side while the total system  
memory is displayed on the right side.  
SETUP  
Press the  
key Select [  
3
System] through tune knob or  
key Select menu through  
knob  
TUNE  
4 190  
JD eng 4b(~211).QXP 3/4/2015 4:39 PM Page 191  
Features of your vehicle  
Language  
This menu is used to set the display and  
voice recognition language.  
Select [Language] Set through  
knob  
TUNE  
❈ The system will reboot after the lan-  
guage is changed.  
❈ Language support by region  
-
4 191  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 192  
Features of your vehicle  
SEEK  
SCAN  
RADIO  
Changing RADIO mode  
RADIO  
FM  
AM  
Press the  
SEEK  
(
TRACK  
,
)key  
RADIO  
FM  
AM  
Press the  
TA/SCAN  
(
,
) key  
,
• Shortly pressing the key (under 0.8  
seconds): Changes the frequency.  
• Pressing and holding the key (over 0.8  
seconds): The broadcast frequency  
increases and previews each broadcast  
for 5 seconds each. After scanning all  
frequencies, returns and plays the cur-  
rent broadcast frequency.  
• Pressing and holding the key (over 0.8  
seconds): Automatically searches for  
the next frequency.  
RADIO  
FM  
AM  
Press the  
to change the mode in order  
(
,
)key Preset SEEK  
Selecting through manual search  
RADIO  
FM  
AM  
Press the  
(
,
) key  
Turn the TUNE knob left/right to adjust  
the frequency.  
RADIO  
: FM1➟FM2  
: FM1 FM2 ➟FMA  
: AM AMA  
➟
FMA  
➟
AM ➟AMA  
1
6
~
FM  
AM  
➟
• Shortly pressing the key (under 0.8  
seconds): Plays the frequency saved in  
the corresponding key.  
➟
- FM : Changes by 50KHz  
- AM : Changes by 9khz  
•
[Mode Pop up] On state : Displays the  
change radio mode pop up screen.  
While the pop up screen is displayed, you  
• Pressing and holding the key (over 0.8  
seconds): Pressing and holding the  
1
6
desired key from  
~
will  
can change the radio mode through the  
1
5
save the currently playing broadcast to  
the selected key and sound a BEEP.  
tune knob or  
~
keys.  
Adjust Volume  
Turn the  
the volume.  
VOL knob left/right to adjust  
4 192  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 193  
Features of your vehicle  
Traffic Announcement (TA)  
AST (Auto Store)  
News  
TA/SCAN  
Shortly pressing the  
(under 0.8 seconds): Set  
Traffic Announcement) mode.  
key  
TA  
MENU  
MENU  
Press the  
through  
key Set [ AST] Press the  
key Set [ News]  
On  
Off  
/
RPT  
1
4
TUNE knob or  
key.  
through  
TUNE knob or  
key.  
The News option can be turned On/Off.  
Select AST (Auto Store) to save fre-  
quencies with superior reception to  
PTY Up/Down  
1
6
presets  
~
. If no frequencies Info Volume  
PTY  
FOLDER  
• Press the  
,
key  
are received, then the most recently  
received frequency will be broadcast.  
Info Volume refers to the sound volume  
upon receiving News or Traffic information.  
The info volume can be controlled by  
turning the VOL knob left/right while a  
news or traffic broadcast is playing.  
when searching PTY in RDS  
Broadcasting Program Type selection.  
❈ Saves only to the Preset memory  
6
1
~
of FMA or AMA mode.  
MENU  
Within  
Region and News functions.  
MENU  
key are the AST, AF,  
❈ AF, Region, and News are RDS Radio  
menus.  
AF (Alternative Frequency)  
MENU  
Press the  
through  
key Set [ AF]  
RDM  
2
TUNE knob or  
key.  
The Alternative Frequency option can be  
turned On/Off.  
Region  
Press the  
through  
MENU  
key Set [ Region]  
3
TUNE knob or  
key.  
The Region option can be turned On/Off.  
4 193  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 194  
Features of your vehicle  
Song Infomation  
Random  
BASIC METHOD OF USE :  
Audio CD / MP3 CD / USB /  
iPod / My Music  
RDM  
SETUP  
2
Press the  
through the  
key Select [ Display] While song (file) is playing  
RPT  
1
TUNE knob or  
key  
(RDM) key  
Select [Song Info] Media Display  
Audio CD, My Music mode: RDM on  
screen  
MEDIA  
Press the  
key to change the  
• [Song Info] : The screen display info  
can be changed to Album/Artist/Song  
name.  
mode in order of CD➟USB(iPod)➟AUX  
➟My Music➟BT Audio.  
• Random (Shortly pressing the key  
(under 0.8 seconds)): Plays all songs in  
random order.  
The folder/file name is displayed on the  
screen.  
MP3 CD, USB mode: FLD.RDM on  
screen  
• Folder Random (Shortly pressing the  
key (under 0.8 seconds)): Plays all files  
within the current folder in random  
order.  
iPod mode: ALB RDM on screen  
Repeat  
• Album Random (Shortly pressing the  
key (under 0.8 seconds)): Plays all files  
within albums of the current category in  
random order.  
RPT  
1
While song (file) is playing  
(RPT) key  
❈ The CD is automatically played when  
a CD is inserted.  
Audio CD, MP3 CD, USB, iPod, My Music  
mode: RPT on screen  
❈ The USB music is automatically  
played when a USB is connected.  
MP3 CD, USB, iPod mode: ALL RDM on  
screen  
• All Random (pressing and holding the  
key (over 0.8 seconds)): Plays all files in  
random order.  
• To repeat one song (Shortly pressing  
the key (under 0.8 seconds)): Repeats  
the current song.  
MP3 CD, USB mode: FLD.RPT on  
screen  
RDM  
2
❈ Press the  
repeat.  
key again to turn off  
• To repeat folder (Pressing and holding  
the key (over 0.8 seconds)): repeats all  
files within the current folder.  
RPT  
1
❈ Press the  
key again to turn off  
repeat.  
4 194  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 195  
Features of your vehicle  
Changing Song/File  
Scan  
Searching Songs (File)  
• Turning  
songs (files)  
TUNE knob : Searches for  
TA/SCAN  
TRACK  
While song (file) is playing  
key  
While song (file) is playing  
key  
• Pressing  
ed song (file).  
TUNE knob : Plays select-  
• Shortly pressing the key (under 0.8  
seconds): Plays the current song from  
the beginning.  
• Pressing and holding the key (over 0.8  
seconds) : Scans all songs for 10 sec-  
onds starting from the next song.  
TA/SCAN  
TRACK  
❈ If the  
key is pressed again  
❈ Press the  
key again to turn  
within 1 second, the previous song is  
played.  
off.  
❈ The SCAN function is not supported in  
iPod mode.  
• Pressing and holding the key (over 0.8  
seconds): Rewinds the song.  
SEEK  
While song (file) is playing  
key  
Folder Search : MP3 CD, USB  
Mode  
• Shortly pressing the key (under 0.8  
seconds): Plays the next song.  
PTY  
While file is playing  
Up) key  
(Folder  
• Pressing and holding the key (over 0.8  
seconds): Fast forwards the song.  
• Searches the next folder.  
FOLDER  
While file is playing  
Down) key  
(Folder  
• Searches the parent folder.  
❈ If a folder is selected by pressing the  
TUNE knob, the first file within the  
selected folder will be played.  
❈ In iPod mode, moves to the Parent  
Folder.  
4 195  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 196  
Features of your vehicle  
MENU : Audio CD  
Information  
MENU : MP3 CD / USB  
MENU  
MENU  
key to  
Press the CD MP3 mode  
key to  
Press the CD MP3 mode  
MENU  
Press the  
through the  
key Set [ Info]  
3
set the Repeat, Random, Information  
features.  
set the Repeat, Folder Random, Folder  
Repeat, All Random, Information, and  
Copy features.  
TUNE knob or  
key to display information of the cur-  
rent song.  
MENU  
❈ Press the  
key to turn off info  
display.  
Repeat  
Repeat  
MENU  
MENU  
Press the  
through the  
key Set [ RPT]  
RPT  
Press the  
through the  
key Set [ RPT]  
RPT  
1
1
TUNE knob or  
key to repeat the current song.  
TUNE knob or  
key to repeat the current song.  
RPT  
1
❈ Press the  
key again to turn off.  
Folder Random  
Random  
MENU  
Press the  
through the  
key Set [ F.RDM]  
RDM  
MENU  
Press the  
through the  
key Set [ RDM]  
RDM  
2
TUNE knob or  
key to randomly play songs within the  
current folder.  
2
TUNE knob or  
key to randomly play songs within  
the current folder.  
RDM  
2
❈ Press the  
key again to turn off.  
4 196  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 197  
Features of your vehicle  
Folder Repeat  
Copy  
key Set [ F.RPT] Press the  
MENU : iPod  
MENU  
key to  
MENU  
MENU  
In iPod mode, press the  
Press the  
through the  
key to repeat songs within the cur- key.  
key Set [ Copy]  
6
set the Repeat, Album Random, All  
Random, Information and Search fea-  
tures.  
3
TUNE knob or  
through the  
TUNE knob or  
rent folder.  
• This is used to copy the current song  
into My Music. You can play the copied  
Music in My Music mode.  
All Random  
❈ If another key is pressed while copying  
is in progress, a pop up asking you  
whether to cancel copying is dis-  
played.  
MENU  
Press the  
through the TUNE knob or  
key Set [ A.RDM]  
4
key  
to randomly play all songs within the  
CD.  
❈ If another media is connected or  
inserted (USB, CD, iPod, AUX) while  
copying is in progress, copying is can-  
celed.  
Repeat  
Information  
MENU  
Press the  
through the  
key Set [ RPT]  
RPT  
1
TUNE knob or  
key to repeat the current song.  
MENU  
Press the  
through the  
key Set [ Info]  
5
❈ Music will not be played while copying  
is in progress.  
TUNE knob or  
key to display information of the cur-  
rent song.  
Album Random  
MENU  
Press the  
key Set [ AlbRDM]  
MENU  
❈ Press the  
display.  
key to turn off info  
RDM  
2
through the  
TUNE knob or  
key.  
Plays albums within the currently playing  
category in random order.  
4 197  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 198  
Features of your vehicle  
• The order of search or playback of  
songs in the iPod can be different from  
the order searched in the audio system.  
• When connecting iPod with the iPod  
Power Cable, insert the connector to the  
multimedia socket completely. If not  
inserted completely, communications  
between iPod and audio may be inter-  
rupted.  
All Random  
MENU  
Press the  
through the  
key.  
key Set [ A.RDM]  
3
TUNE knob or  
• If the iPod is disabled due to its own  
malfunction, reset the iPod. (Reset:  
Refer to iPod manual)  
Plays all songs within the currently play-  
ing category in random order.  
• When adjusting the sound effects of the  
iPod and the audio system, the sound  
effects of both devices will overlap and  
might reduce or distort the quality of the  
sound.  
• An iPod may not operate normally on  
low battery.  
Information  
• Some iPod devices, such as the  
iPhone, can be connected through the  
-interface. The device must have audio  
Bluetooth® Wireless Technology capa-  
bility (such as for stereo headphone  
Bluetooth® Wireless Technology ). The  
device can play, but it will not be con-  
trolled by the audio system.  
MENU  
Press the  
through the  
key.  
key Set [ Info]  
4
TUNE knob or  
• Deactivate (turn off) the equalizer func-  
tion of an iPod when adjusting the audio  
system’s volume, and turn off the  
equalizer of the audio system when  
using the equalizer of an iPod.  
Displays information of the current song.  
Search  
• When not using iPod with car audio, detach  
the iPod cable from iPod. Otherwise, iPod  
may remain in accessory mode, and may  
not work properly.  
• To use iPod features within the audio, use  
the cable provided upon purchasing an  
iPod device.  
MENU  
Press the  
through the  
key.  
key Set [ Search]  
5
TUNE knob or  
• Skipping or improper operation may occur  
depending on the characteristics of your  
iPod/Phone device.  
• Some iPod models may not support  
communication protocol and files may  
not properly play.  
• If your iPhone is connected to both the  
Bluetooth® Wireless Technology and  
USB, the sound may not be properly  
played. In your iPhone, select the Dock  
connector or Bluetooth® Wireless  
Technology to change the sound output  
(source).  
Supported iPod models:  
- iPod Mini®  
- iPod 4th(Photo) ~ 6th(Classic) genera-  
tion  
- iPod Nano® 1st~4th generation  
- iPod Touch® 1st~2nd generation  
4 198  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 199  
Features of your vehicle  
MENU : My Music  
Information  
Delete All  
MENU  
MENU  
Press the  
through the  
key Set [ Info] Press the  
3
key Set [ Del.All]  
5
TUNE knob or  
through the TUNE knob or  
key.  
MENU  
In My Music mode, press the  
key  
to set the Repeat, Random, Information, key.  
Delete, Delete All, and Delete Selection  
features.  
Deletes all songs of My Music.  
Displays information of the current song.  
Delete Selection  
MENU  
❈ Press the  
display.  
key to turn off info  
MENU  
Press the  
through the  
key.  
key Set [ Del.Sel]  
6
TUNE knob or  
Delete  
Songs within My Music are selected and  
deleted.  
➀ Select the songs you wish to delete  
MENU  
Press the  
key Set [ Delete]  
4
through the  
key.  
TUNE knob or  
from the list.  
Repeat  
MENU  
Press the  
through the  
key Set [ RPT]  
Deletes currently playing file  
RPT  
1
TUNE knob or  
key.  
Repeats the currently playing song.  
Random  
MENU  
Press the  
through the  
key Set [ RDM]  
RDM  
2
TUNE knob or  
key.  
MENU  
➁ After selecting, press the  
and select the delete menu.  
key  
Plays all songs within the currently play-  
ing folder in random order.  
In the play screen, pressing delete will  
delete the currently playing song.  
Deletes file from list  
➀ Select the file you wish to delete by  
TUNE knob.  
using the  
➁ Press the  
MENU  
key and select the  
delete menu to delete the selected file.  
4 199  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 200  
Features of your vehicle  
AUX  
✽
NOTICE FOR USING THE My  
Music  
AUX is used to play external MEDIA cur-  
rently connected with the AUX terminal.  
• Even if memory is available, a maxi-  
mum of 6,000 songs can be stored.  
• The same song can be copied up to  
1,000 times.  
AUX mode will automatically start when  
an external device is connected with the  
AUX terminal.  
• Memory info can be checked in the  
System menu of Setup.  
If an external device is connected, you  
MEDIA  
can also press the  
to AUX mode.  
key to change  
❈ AUX mode cannot be started unless  
there is an external device connected  
to the AUX terminal.  
❈ Fully insert the AUX cable into the  
AUX terminal for use.  
4 200  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 201  
Features of your vehicle  
Bluetooth® Wireless Technology  
AUDIO  
Before using Bluetooth® Wireless  
Starting Bluetooth® Wireless  
Technology Audio  
Changing Song/File  
TRACK  
While song (file) is playing  
key  
TRACK  
MEDIA  
• Press the  
mode in order of CD➟USB➟AUX➟My  
key to change the  
Technology audio features  
• Press the  
key : Plays the  
Music➟BT Audio.  
• Bluetooth® Wireless Technology audio  
may not be supported depending on  
the compatibility of your Bluetooth®  
Wireless Technology mobile phone.  
• In order to use Bluetooth® Wireless  
Technology audio, you must first pair and  
connect the Bluetooth® Wireless  
Technology mobile phone.  
current song from the beginning.  
TRACK  
• If BT Audio is selected, Bluetooth®  
Wireless Technology audio will start play-  
ing.  
❈ If the  
key is pressed again  
within 1 second, the previous song is  
played.  
❈ Audio may not automatically start play-  
ing in some mobile phones.  
SEEK  
While song (file) is playing  
key  
SEEK  
• Press the  
next song.  
key : Plays the  
• Bluetooth® Wireless Technology audio  
can be used only when the [Audio  
On  
Streaming] of Phone is turned  
.
❈ Setting Bluetooth® Wireless Technology  
SETUP  
Audio Streaming : Press the  
key Select [Phone] through the tune  
3
knob or  
Streaming] through the  
key Select [Audio  
TUNE  
Using the Bluetooth® Wireless  
Technology audio features  
• Play / Stop  
On  
Off  
knob Set  
/
Press the TUNE knob to play and  
pause the current song.  
❈ The previous song / next song / play /  
pause functions may not be supported  
in some mobile phones.  
4 201  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 202  
Features of your vehicle  
Check call history and making call  
Making a call using the Steering  
remote controller  
PHONE (if equipped)  
➀ Shortly press (under 0.8 seconds) the  
key on the steering remote con-  
troller.  
Before using the Bluetooth® Wireless  
Technology phone features  
➁ The call history list will be displayed  
on the screen.  
• In order to use Bluetooth® Wireless  
Technology phone, you must first pair  
and connect the Bluetooth® Wireless  
Technology mobile phone.  
➂ Press the  
call to the selected number.  
key again to connect a  
Redialing the most recently called  
number  
• If the mobile phone is not paired or con-  
nected, it is not possible to enter Phone  
mode. Once a phone is paired or con-  
nected, the guidance screen will be dis-  
played.  
➀ Press and hold (over 0.8 seconds) the  
key on the steering remote con-  
troller.  
➁ The most recently called number is  
redialed.  
(1) VOLUME button : Raises or lowers  
speaker volume.  
• If Priority is set upon vehicle ignition  
(IGN/ACC ON), the Bluetooth® Wireless  
Technology phone will be automatically  
connected. Even if you are outside, the  
Bluetooth® Wireless Technology phone  
will be automatically connected once  
you are in the vicinity of the vehicle. If  
you do not want automatic Bluetooth®  
Wireless Technology phone connection,  
set the Bluetooth® Wireless Technology  
to OFF.  
(2) MUTE button : Mutes audio Volume  
during a call.  
(3)  
(4)  
(5)  
button : Activates voice recogni-  
button : Places and transfers  
button : Ends calls or cancels  
tion.  
calls.  
functions.  
4 202  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 203  
Features of your vehicle  
Phone Book  
Phone MENU  
✽
NOTICE  
PHONE  
If you need more information about  
Kia’s Bluetooth® Wireless Technology.  
Contact kia website “www.kia.com”  
(OWNERS>General Info>Bluetooth®  
Wireless Technology ).  
PHONE  
Press the  
key to display three  
Press the  
through the  
key Set [ P. Book]  
menus (Call History, Phone book, Phone  
Setup).  
RDM  
2
TUNE knob or  
key.  
The Phone book is displayed and can be  
used to select a number and make a call.  
❈ If more than one number is saved to  
one contact, then a screen showing  
the mobile phone number, house and  
office number is displayed. Select the  
desired number to make the call.  
❈ If Phone book does not exist, a screen  
asking whether to download Phone  
book is displayed. (The download fea-  
ture may not be supported in some  
mobile phones)  
Call History  
PHONE  
Press the  
through the  
key.  
key Set [ History]  
RPT  
1
TUNE knob or  
Phone Setup  
The call history is displayed and can be  
used to select a number and make a call.  
PHONE  
Press the  
through the  
key.  
key Set [  
Setup]  
3
TUNE knob or  
If call history does not exist, a screen ask-  
ing whether to download call history is  
displayed. (The download feature may not  
be supported in some mobile phones)  
The Bluetooth® Wireless Technology  
mobile phone setup screen is displayed.  
For more information, refer to “Phone  
Setup”.  
4 203  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 204  
Features of your vehicle  
• Bluetooth® Wireless Technology features  
• Some features may not be supported in  
some Bluetooth® Wireless Technology  
enabled mobile phone and devices.  
• Bluetooth® Wireless Technology func-  
tions may operate unstably depending  
on the communication state.  
What is Bluetooth® Wireless  
Technology?  
can be used only when the mobile phone  
has been paired and connected with the  
device. For more information on pairing  
and connecting Bluetooth® Wireless  
Technology endbled mobile phones,  
refer to the “Phone Setup” section.  
Bluetooth® Wireless Technology that  
allows multiple devices to be connected  
in a short range, low-powered devices  
like hands-free, stereo headset, wireless  
remote controller, etc. For more information,  
visit the Bluetooth® Wireless Technology  
website at www.Bluetooth.com  
• Do not use a cellular phone or perform  
Bluetooth® Wireless Technology settings  
(e.g. pairing a phone) while driving.  
• When  
a
Bluetooth®  
Wireless  
Technology mobile phone is connected,  
a ( ) icon will appear at the top of the  
screen. If a ( ) icon is not displayed,  
• Some Bluetooth® Wireless Technology  
-
enabled phones may not be recognized  
by the system or fully compatible with  
the system.  
• Before using Bluetooth® Wireless  
Technology related features of the audio  
system, refer your phone’s User’s  
Manual for phone-side Bluetooth®  
Wireless Technology operations.  
this indicates that  
a
Bluetooth®  
Wireless Technology enabled device  
has not been connected. Your must  
connect the device before use. For  
more information on Bluetooth®  
Wireless Technology mobile phones,  
refer to the “Phone Setup” section.  
• Pairing and connecting a Bluetooth®  
Wireless Technology enabled mobile  
phone will work only when the  
Bluetooth® Wireless Technology option  
within your mobile phone has been  
turned on. (Methods of turning on the  
•
The phone must be paired to the audio  
system to use Bluetooth® Wireless  
Technology related features.  
• You will not be able to use the hands-  
free feature when your phone (in the  
car) is outside of the cellular service  
area (e.g. in a tunnel, in a underground,  
in a mountainous area, etc.).  
Bluetooth®  
Wireless  
Technology  
enabled feature may differ depending  
on the mobile phone.)  
• In some mobile phones, starting the  
ignition while talking through Bluetooth®  
Wireless Technology handsfree call will  
result in the call becoming disconnect-  
ed. (Switch the call back to your mobile  
phone when starting the ignition.)  
(Continued)  
4 204  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 205  
Features of your vehicle  
(continued)  
• If you do not want automatic Bluetooth®  
Wireless Technology power off.  
• If the cellular phone signal is poor or the  
vehicles interior noise is too loud, it may  
be difficult to hear the other person’s  
voice during a call.  
• Do not place the phone near or inside  
metallic objects, otherwise communica-  
tions  
with  
Bluetooth®  
Wireless  
Technology system or cellular service  
stations can be disturbed.  
• While a phone is connected through  
Bluetooth® Wireless Technology your  
phone may discharge quicker than usual  
for additional Bluetooth® Wireless  
Technology-related operations.  
• Some cellular phones or other devices  
may cause interference noise or mal-  
function to audio system. In this case,  
store the device in a different location  
may resolve the situation.  
• Please save your phone name in  
English, or your phone name may not  
be displayed correctly.  
• If Priority is set upon vehicle  
ignition(IGN/ACC ON), the Bluetooth®  
Wireless Technology phone will be auto-  
matically connected.  
Even if you are outside, the Bluetooth®  
Wireless Technology phone will be auto-  
matically connected once you are in the  
vicinity of the vehicle.  
4 205  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 206  
Features of your vehicle  
• Upon inputting your phone book, spe-  
Starting Voice Command  
VOICE COMMAND (if equipped)  
cial symbols and numbers cannot be  
recognized by voice. For example, “#  
John Doe%&” will be recognized as  
“John Doe”.  
• To start voice command, shortly press  
the key on the steering wheel  
remote controller.  
• The voice recognition feature of this  
product supports recognition of the  
commands listed within this user’s  
manual.  
• If voice command is in [Normal Mode],  
then the system will say “Please say a  
command. Beep”  
• While using voice recognition, operating  
the steering remote control or the device  
will terminate voice recognition and allow  
you to manually operate desired func-  
tions.  
❈ If voice command is in [Expert Mode],  
then the system will only say a “Beep-”  
❈ Setting Voice command [Normal  
Mode]/[Expert Mode]:  
• Position of the microphone is above the  
head of the driver’s seat.  
SETUP  
Press the  
through the  
key Select [ System]  
4
TUNE knob or  
key  
• Voice recognition may not function  
properly due to outside noise. The fol-  
lowing conditions can affect the per-  
formance of Voice Recognition:  
Select [Prompt Feedback] through the  
TUNE knob Set [Normal Mode]/[Expert  
Mode]  
• Say the voice command.  
- When the windows and sunroof are  
open  
- When the heating/cooling system is on  
- When passing a tunnel  
• For proper voice recognition, say the  
voice command after the guidance  
message and the “Beep” sound.  
- When driving on rugged and uneven  
roads  
• After downloading Bluetooth® Wireless  
Technology phone book, the system  
requires some times to convert the  
phone book into voice information.  
During this time, voice recognition may  
not operate properly.  
4 206  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 207  
Features of your vehicle  
Skipping the Guidance Message  
Ending Voice Command  
While the guidance message is being  
stated, shortly press the  
0.8 seconds) to discontinue the guidance  
message and sound the “beep”.  
After the “beep”, say the voice command.  
• While using voice command, press and  
hold the key (over 0.8 seconds) to  
end voice command.  
key (under  
• While using voice command, pressing  
the steering wheel remote controller or  
a different key will end voice command.  
• In a state where the system is waiting  
for your voice command, say “cancel” or  
“end” to end voice command.  
• In a state where the system is waiting  
for your voice command, shortly press  
the key (under 0.8 seconds) to end  
voice command.  
4 207  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 208  
Features of your vehicle  
Monday  
Monday  
Playlists  
Songs  
"Playlists" is filtering keyword for  
searching mode of playlists for iPod  
"Songs" is filtering keyword for  
searching mode of playlists for iPod  
"Audiobooks" is filtering keyword  
for searching mode of playlists  
for iPod  
Tuesday  
Wednesday  
Thursday  
Friday  
Tuesday  
Wednesday  
Thursday  
Friday  
Audiobooks  
Saturday  
Sunday  
Saturday  
Sunday  
Use tune knob  
Volume  
Use tune knob  
Podcasts  
"Podcasts" is filtering keyword  
for searching mode of playlists  
for iPod  
Volume  
Max  
Volume maxinmum  
Volume mininmum  
Automatically selects and saves  
channels  
Min  
RPT (Repeat)  
Audio play mode of Reapeat  
Audio play mode of Folder  
Reapeat  
AST (Auto store)  
F.RPT (Folder Repeat)  
No Media  
No File  
Empty media file in CD or USB  
Empty media file in CD or USB  
Empty media file in MY MUSIC  
Information of playing files  
Artist name, MP3/CD file cur-  
rently being played  
Song name, MP3/CD file cur-  
rently being played  
Album name, MP3/CD file cur-  
rently being played  
"Genres" is keyword for search-  
ing mode of playlists for iPod  
"Composers" is filtering keyword  
for searching mode of playlists  
for iPod  
RDM (Random)  
Audio play mode of Random  
Audio play mode of Folder  
Random  
F.RDM(Folder Random)  
Empty File  
Info (Information)  
Artist  
A.RDM (All Random)  
COPY  
Audio play mode of All Random  
Copy MP3 file to flash memory  
for MY MUSIC  
Title  
Cancel copy  
File copied  
Free  
Cancel copy mode  
Completed File copy  
Free size of memory  
Copy failed  
Album  
Copy failed  
Search  
Genres  
Composers  
Search files  
Loading CD  
Reading CD  
Reading Error  
Mechanism Error  
Ejecting CD  
Loading CD  
Reading CD  
Reading Error  
Mechanism Error  
Ejecting CD  
4 208  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 209  
Features of your vehicle  
Audio CD  
Audio CD  
Mode Pop up  
Scroll text  
This function is used to select  
popup menu on or off  
Track  
Audio CD song order  
Reading Media  
Reading Media  
Not supported  
Empty iPod  
This function is used to display  
characters longer than the LCD  
text displays  
Not supported file format  
Empty iPod, iPod don't have  
playable data  
Song Info  
Setup display information being  
played  
Communication Error  
Delete  
Communication error between  
audio and iPod or usb  
Delete the paired phone or files  
in MY MUSIC  
Folder/File  
Display Folder/file name, file  
currently being played  
Album/Artist/Song  
Display Album/Artist/Song  
name, file currently being played  
Setup sound mode  
Del.All  
Delete all files  
Del.Sel  
Return  
List  
Select files to delete  
Return menu  
Sound  
Audio Settings  
Setup Audio settings that con-  
sist BASS,Middle,Treble,Fader  
and Balance  
List files or paired phones  
Select Files  
Select Files  
Memory is full,  
Delete files  
Memory is full, Delete  
files  
PowerBass  
This function is used to improve  
bass sound quality  
Over 6000 files. can  
not be copied  
Over 6000 files. can not be  
copied  
Speed Dependent Vol.  
Automatically adjust the volume  
according to the car speed  
Adjust volume level of Dialogue  
Bass is sound of low frequency.  
It can be adjusted sound by  
user  
Over 1000 same files  
can not be copied  
Over 1000 same files can not  
be copied  
Volume Dialogue  
Bass  
System will automati-  
cally switchoff after 1  
hour with ignition off  
System will automatically  
switchoff after 1 hour with  
Middle  
Treble  
Middle is sound of middle fre-  
quency. It can be adjusted  
sound by user  
Battery discharge  
Start the engine  
Battery discharge  
Start the engine  
Setup  
Setup  
Treble is sound of high frequency. It  
can be adjusted sound by user  
Display  
Setup display mode  
4 209  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 210  
Features of your vehicle  
Fader  
Fader is sound positon between  
Dansk  
Polski  
Danish  
FRONT and REAR. It can be  
adjusted sound by user  
Balance is sound positon  
between Right and Left. It can  
be adjusted sound by user  
This function is used to initialize  
setting value  
Polish  
Russian  
Balance  
The system will be  
rebooted  
The system will be  
rebooted  
Please change language  
when ignition ON  
Please change language when  
ignition ON  
Default  
System  
Bluetooth not ready  
Please wait  
You can use BT System for a  
moment Because BT system is  
being initialized  
Setup system or system infor-  
mation  
Memory Information  
VRS Mode  
Display used memory size  
Setup Voice command mode  
Normal mode. This function is  
used to set default value of  
voice recognition factor  
Expert mode. This function is  
used to set exercised value of  
voice recognition factor  
This function is used to select  
user language  
Add a new Bluetooth  
device from your phone  
Add a new Bluetooth® Wireless  
Technology device from your phone  
You can use BT System for a  
moment Because BT system is  
being initialized or processing  
other command  
Normal  
Processing Bluetooth  
Please try later  
Expert  
Incoming Call  
Call Ended  
Receivng phone  
Call Ended  
Language  
Deutsch  
Call Rejected  
When there is unwanted call,  
You push the button on the  
steering remote controller  
"Unknown" mean Headunit or  
phone don't have any informa-  
tion about phone number  
Call is not possible  
Deutsch  
Unknown  
English(UK)  
Français  
Italiano  
English(UK)  
French  
Call is not possible  
MIC Mute  
Italian  
Microphone mute  
Español  
Spanish  
dutch  
Activate Bluetooth  
System?  
Activate Bluetooth® Wireless  
Nederlands  
Svenska  
Technology System  
Bluetooth® Wireless  
Technology system activated  
swedish  
Bluetooth System  
activated  
4 210  
JD eng 4b(~211).QXP 3/4/2015 4:40 PM Page 211  
Features of your vehicle  
No phone paired.  
Pair a phone?  
Empty phone paired.  
Pairing failed  
Audio & Phone connection have  
failed  
Pair a phone?  
No connected phone.  
Connect a phone?  
No connected phone. Connect a  
phone?  
Already 5 devices  
paired. Delete a  
All 5 phones have already been  
paired. Delete a previously  
paired phone to pair new phone  
Audio & Phone connection have  
succeed  
paired phone?  
Phone book is empty.  
Download?  
Phone book is empty  
Connection complete  
Available only when  
vehicle is stationary  
This is a warning, Do not enter  
the MENU about BT Setup.  
When vehicle is moving  
Connection failed.  
Retry?  
Audio & Phone connection have  
failed  
Listening...  
Listen to instruction of audio  
Downloading phone book from  
phone paired to audio  
Priority changed  
Changed priority about the reg-  
istered phones  
Phone book Download  
Overwrite previous  
phone book?  
Overwrite previous phone book  
information  
Auto Download  
Audio Streaming  
After pairing phone, audio sys-  
tem automatically download  
phone book  
Phone does not support  
Phone book download  
Phone does not support Phone  
book download  
After pairing phone, audio system  
can support Bluetooth® Wireless  
Technology streaming mode  
Set outoging volume "0 ~ 5"  
Turn off Bluetooth® Wireless  
Technology System  
No connected  
Bluetooth device  
There are phone in the  
connection list  
Phone does not support  
Bluetooth audio  
But it was actually not connect-  
ed BT pairing  
Outgoing Volume  
Bluetooth System Off  
Downloading stopped  
Downloading stopped  
Bluetooth System ON  
Device :  
Turn on Bluetooth® Wireless  
Technology System  
Bluetooth® Wireless  
Technology device name  
Passkey for pairing a phone  
Pair a Bluetooth® Wireless  
Technology phone to the audio  
Passkey  
Pairing complete  
4 211  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 212  
Features of your vehicle  
■ CD Player : AC111A2EE  
4 212  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 213  
Features of your vehicle  
SEEK  
TRACK  
SYSTEM CONTROLLERS AND  
FUNCTIONS  
(1) (EJECT)  
Ejects the disc.  
(6)  
When pressed shortly(under 0.8 seconds)  
- Radio mode : plays previous/next fre-  
quency.  
Audio Head Unit  
RADIO  
(2)  
Switches to Radio(FM/AM) mode.  
- Media (CD/USB/iPod/My Music) modes  
: changes the track, Song(file)  
When pressed and held (0.8 seconds)  
Each time the key is pressed,the mode is  
changed in order of FM1 ➟ FM2 ➟ FMA  
➟ AM ➟ AMA.  
- Radio mode : continuously changes the  
frequency. Upon release, plays the cur-  
rent frequency  
MEDIA  
(3)  
Switches to Media mode.  
-
Media(CD/USB/iPod/My Music) modes :  
rewinds or fast forwards the track or file  
Each time the key is pressed, the mode  
is changed in order of CD, USB(iPod)  
AUX, My Music, BT Audio.  
- During a Handsfree call, controls the  
call volume.  
PTY  
FOLDER  
(7)  
PHONE  
(4)  
Switches to Phone mode.  
RDS Radio mode : searches RDS pro-  
gram types.  
CD/USB/MP3 modes : searches folders.  
❈ When a phone is not connected, the  
connection screen is displayed.  
(5) PWR/VOL knob  
Power : Press to turn power on/off.  
Volume : Turn left/right to control vol-  
ume.  
4 213  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 214  
Features of your vehicle  
SETUP  
(11)  
Switches to Setup mode.  
(12) TUNE knob  
Radio mode : turn to change broadcast  
frequencies.  
Media (CD/USB/iPod/My Music) modes :  
turn to search tracks/channels/files.  
(8)  
Turns the monitor display on/off.  
(13) RESET  
Forced system termination and system  
restart.  
TA  
(9)  
Set TA(Traffic Announcement) feature  
On/Off  
SCAN  
(10)  
Radio Mode  
- Shortly press the key (under 0.8 sec-  
onds): Previews each broadcast for 5  
seconds each  
-
Press and hold the key (over 0.8 seconds):  
Previews the broadcasts saved in Preset  
1
6
for 5 seconds each.  
~
Media (CD/USB/iPod/My Music) modes :  
previews each song (file) for 10 seconds  
each.  
4 214  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 215  
Features of your vehicle  
When pressed and held (over 0.8 seconds)  
- Radio mode, automatically searches  
broadcast frequencies and channels  
Steering remote controller  
(6)  
When pressed shortly (under 0.8 seconds)  
- When pressed in the phone screen,  
displays call history screen  
- Media(CD/USB/iPod/My Music) modes,  
rewinds or fast forwards the track or  
song(file)  
- When pressed in the dial screen,  
makes a call  
- When pressed in the incoming call  
screen, answers the call  
(4) MODE  
- When pressed during call waiting,  
switches to waiting call (Call Waiting)  
When pressed and held (over 0.8 seconds)  
- When pressed in the Bluetooth®  
Wireless Technology Handsfree wait  
mode, redials the last call  
- When pressed during a Bluetooth®  
Wireless Technology Handsfree call,  
switches call back to mobile phone  
(Private)  
Each time this key is pressed, the mode  
is changed in order of FM1➟FM2  
➟FMA➟ AM➟AMA➟USB or iPod➟AUX  
➟My Music➟BT Audio  
If the media is not connected or a disc is  
not inserted, corresponding modes will  
be disabled.  
(1) VOLUME  
Used to control volume.  
(5)  
When pressed shortly (under 0.8 seconds)  
- Starts voice recognition  
- When pressed while calling on the  
mobile phone, switches call back to  
(2) MUTE  
Mutes audio volume.  
Bluetooth®  
Wireless  
Handsfree (Operates only when  
Bluetooth®  
Wireless Technology  
Handsfree is connected)  
Technology  
- When selecting during a voice prompt,  
stops the prompt and converts to voice  
command waiting state  
(3) SEEK  
When pressed shortly (under 0.8 seconds)  
When pressed and held (over 0.8 seconds)  
- Ends voice recognition  
- Radio mode : searches broadcast fre-  
quencies saved to presets.  
(7)  
Ends phone call  
- Media (CD / USB / iPod / My Music / BT  
Audio) modes : changes the track, file.  
4 215  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 216  
Features of your vehicle  
(1) Mode Display  
Switching to Radio Mode  
RADIO MODE  
Displays currently operating mode  
Basic Mode Screen  
RADIO  
Pressing the  
key will change  
the operating mode in order of FM1  
➟FM2➟FMA➟AM➟AMA.  
(2) Frequency  
Displays the current frequency  
(3) Preset  
Displays current preset number [1] ~  
[6]  
(4) Preset Display  
Displays saved presets  
If [Pop-up Mode] is turned on within  
SETUP  
[Display], then pressing the  
key will display the Radio Pop-  
(5) Autostore  
RADIO  
Automatically saves frequencies with  
superior reception to Preset buttons  
up Mode screen.  
Turn the TUNE knob to move the  
focus. Press the knob to select.  
(6) RDS Menu  
Displays the RDS Menu  
(7) RDS Info  
Displays RDS broadcast information  
4 216  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 217  
Features of your vehicle  
Searching Radio Frequencies  
Using Radio Mode  
✽
NOTICE  
While listening to a frequency you want  
to save as a preset, press and hold one of  
the [1] ~ [6] preset buttons (over 0.8 sec-  
onds) to save the current frequency to  
the selected preset.  
Using Seek  
Selecting /Saving Presets  
SEEK  
Press the  
previous/next frequency.  
TRACK  
key to play the Press the  
1
~
the desired preset.  
6
buttons to play  
Auto Store  
Using TUNE  
Press the  
cally save receivable frequencies to  
Preset buttons.  
button to automati-  
Turn the  
desired frequency.  
TUNE knob to select the  
• FM : Increases/decreased by 50kHz  
• AM : Increases/decreased by 9kHz  
✽
NOTICE  
While Auto Store is operating, pressing  
the [Cancel] button again will cancel  
Auto Store and restore the previous fre-  
quency.  
Press the  
button to display the  
broadcast information for the frequency  
saved to each button.  
4 217  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 218  
Features of your vehicle  
RDS Menu  
Program Type  
TA (Traffic Announcement)  
Press the  
(Alternative Frequency), Region and  
News features.  
button to set the AF  
PTY  
FOLDER  
Press the  
key to search for  
TA  
Press the  
key to turn the TA  
(Traffic Announcement) feature  
On/Off.  
the desired Program type.  
Turn the  
TUNE knob left/right to  
search for the desired program type.  
Once you find the desired program type,  
✽
NOTICE  
The RDS Menu is not supported within  
AM or AMA mode.  
press the  
TUNE knob.  
After selecting the desired Program Type  
and while the Program Type is blinking  
Scan  
SCAN  
Press the  
quencies with superior reception for  
5 seconds each.  
key to preview fre-  
(approximately 5 seconds), pressing the  
PTY  
key will allow you to select a  
FOLDER  
different Program Type broadcast.  
✽
NOTICE  
Once scan is complete, the previous fre-  
quency will be restored.  
While Scan is operating, pressing the  
SCAN  
key will cancel the scan opera-  
tion.  
4 218  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 219  
Features of your vehicle  
✽
MEDIA MODE  
Switching to Media Mode  
MEDIA  
NOTICE  
The media mode pop up screen can be  
displayed only when there are two or  
more media modes turned on.  
Title Icon  
Pressing the  
key will change  
Bluetooth® Wireless  
the operating mode in order of  
➟
When  
a
CD➟USB(iPod)➟AUX➟My Music  
BT Audio.  
Technology, iPod, USB, or AUX  
device is connected or a CD is  
inserted, the corresponding mode  
icon will be displayed.  
Icon  
Title  
Bluetooth® Wireless Technology  
CD  
If [Pop-up Mode] is turned on within  
SETUP  
[Display], then pressing the  
key will display the Media  
Pop-up Mode screen.  
iPod  
USB  
AUX  
MEDIA  
Turn the TUNE knob to move the  
focus. Press the knob to select.  
4 219  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 220  
Features of your vehicle  
(1) Mode  
(7) Random  
AUDIO CD MODE  
Basic Mode Screen  
Displays currently operating mode  
Turns the Random feature on/off  
(2) Operation State  
(8) Repeat  
From Repeat / Random / Scan, dis- Turns the Repeat feature on/off  
plays the currently operating function  
(9) List  
(3) Track Info  
Moves to the list screen  
Displays information about the cur-  
rent track  
(4) Play/Pause  
Changes the play/pause state  
(5) Play Time  
Displays the current play time  
(6) Info  
Shows detailed information about  
the current track  
4 220  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 221  
Features of your vehicle  
Changing Tracks  
Rewinding / Fast-forwarding Tracks  
Using Audio CD Mode  
SEEK  
Press the  
the previous or next track.  
key to move to While playing, press and hold the  
SEEK  
TRACK  
key (over 0.8 seconds) to  
rewind or fast-forward the current  
track.  
TRACK  
Playing/Pausing CD Tracks  
Once an audio CD is inserted, the  
mode will automatically start and  
begin playing.  
✽
NOTICE  
• Pressing the  
SEEK  
TRACK  
key after the  
track has been playing for 1 seconds  
will start the current track from the  
beginning.  
Scan  
SCAN  
Press the  
10 seconds of each file.  
key to play the first  
SEEK  
• Pressing the  
key before the  
TRACK  
track has been playing for 1 seconds  
will start the previous track.  
Selecting from the List  
Turn the TUNE knob left/right to  
search for the desired track.  
While playing, press the  
to pause and press  
play.  
button  
button to  
✽
NOTICE  
• Only genuine audio CDs are support-  
ed. Other discs may result in recogni-  
tion failure (e.g. copy CD-R, CDs with  
labels)  
• The artist and title information are  
displayed on the screen if track infor-  
mation is included within the audio  
CD.  
Once you find the desired track, press  
TUNE knob to start playing.  
the  
4 221  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 222  
Features of your vehicle  
Info  
List  
Audio CD Mode Menu  
Press the  
details about the current disc.  
button to display Press the  
button to display the  
Within this mode, you will have  
access to the Info, Random, Repeat  
and List features.  
track list screen.  
Random  
Press the button to play tracks  
in random order.  
Press the button again to turn the  
Random feature off.  
Repeat  
Press the  
button to repeat the  
Turn the  
TUNE knob left/right to  
current track. Press the button again  
to turn the repeat feature off.  
search for tracks. Once the desired track  
is displayed, press the knob to select and  
play.  
4 222  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 223  
Features of your vehicle  
(1) Mode  
(8) Random  
MP3 CD MODE  
Displays currently operating mode.  
Turns the Random feature on/off  
Basic Mode Screen  
(2) Operation State  
(9) Repeat  
From Repeat / Random / Scan, dis- Turns the Repeat feature on/off  
plays the currently operating function  
(10) Copy  
(3) File Index  
Copies the current file into My Music  
Displays the current file number  
(11) List  
(4) File Info  
Moves to the list screen  
Displays information about the current file  
(5) Play/Pause  
Changes the play/pause state  
(6) Play Time  
Displays the current play time  
(7) Info  
Shows detailed information about  
the current file  
4 223  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 224  
Features of your vehicle  
Rewinding / Fast-forwarding Files  
Using MP3 CD Mode  
Changing Files  
Press the  
the previous or next file.  
SEEK  
TRACK  
key to move to  
While playing, press and hold the  
SEEK  
key (over 0.8 seconds) to  
rewind or fast-forward the current file.  
TRACK  
Playing/Pausing MP3 Files  
Once an MP3 disc is inserted the  
mode will automatically start and  
being playing.  
✽
NOTICE  
• Pressing the  
SEEK  
TRACK  
Scan  
key after the file  
has been playing for 1 seconds will  
start the current file from the begin-  
ning.  
SCAN  
Press the  
10 seconds of each file.  
key to play the first  
SEEK  
• Pressing the  
key before the  
TRACK  
file has been playing for 1 seconds will  
start the previous file.  
Selecting from the List  
Turn the TUNE knob left/right to  
search for the desired file.  
While playing, press the  
to pause and press  
play.  
button  
button to  
✽
NOTICE  
If there are numerous files and folders  
within the disc, reading time could take  
more than 10 seconds and the list may  
not be displayed or song searches may  
not operate. Once loading is complete,  
try again.  
Once you find the desired file, press the  
TUNE knob to start playing.  
4 224  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 225  
Features of your vehicle  
Searching Folders  
PTY  
• The title, artist and album info are dis-  
played only when such information are  
recorded within the MP3 file ID3 tag.  
MP3 CD Mode Menu  
Press the  
and search folders.  
key to select  
FOLDER  
Within this mode, you will have  
access to the Info, Random, Repeat,  
Copy and List features.  
Once the desired folder is displayed,  
press the TUNE knob to select.  
Random  
Press the  
random order.  
button to play files in  
Each time the button is pressed, the fea-  
ture changes in order of Random Folder  
➟ Random All➟ Off.  
• Random Folder : Plays all files within  
the current folder in Random order.  
• Random All : Plays all files in Random  
order.  
The first file within the selected folder will  
begin playing.  
Info  
Press the  
details about the current file.  
button to display  
✽
NOTICE  
• When the ‘Folder File’ option is set as  
the default display within Display  
setup, the album/artist/file informa-  
tion are displayed as detailed file infor-  
mation.  
• When the ‘Album Artist Song’ option  
is set as the default display, the folder  
name/file name are displayed as  
detailed file information.  
4 225  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 226  
Features of your vehicle  
Repeat  
List  
Press the  
current file or folder.  
button to repeat the Press the  
button to display the  
file list screen.  
Each time the button is pressed, the fea-  
ture changes in order of Repeat ➟Repeat  
Folder➟Off.  
• Repeat: Repeats the current file.  
• Repeat Folder: Repeats all files within  
the current Folder.  
Copying Files  
Press the  
current file into My Music.  
button to copy the  
Turn the  
TUNE knob left/right to  
search for files. Once the desired file is  
displayed, press the knob to select and  
play.  
✽
NOTICE  
Selecting another feature during copy-  
ing will display a pop-up asking whether  
you wish to cancel copying. To cancel,  
select 'Yes’.  
4 226  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 227  
Features of your vehicle  
(1) Mode  
(8) Random  
USB MODE  
Displays currently operating mode  
Turns the Random feature on/off  
Basic Mode Screen  
(2) Operation State  
(9) Repeat  
From Repeat / Random / Scan, dis- Turns the Repeat feature on/off  
plays the currently operating function  
(10) Copy  
(3) File Index  
Copies the current file into My Music  
Displays the current file number  
(11) List  
(4) File Info  
Moves to the list screen  
Displays information about the current file  
(5) Play/Pause  
Changes the play/pause state  
(6) Play Time  
Displays the current play time  
(7) Info  
Displays detailed information for the  
current file  
4 227  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 228  
Features of your vehicle  
Rewinding / Fast-forwarding Files  
Using USB Mode  
Changing Files  
While playing, press and hold the  
SEEK  
SEEK  
Press the  
the previous or next file.  
keys to move to  
key (over 0.8 seconds) to  
rewind or fast-forward the current file.  
TRACK  
Playing/Pausing USB Files  
TRACK  
Once a USB is connected, the mode  
will automatically start and begin  
playing a USB file.  
✽
NOTICE  
• Pressing the  
Scan  
SEEK  
TRACK  
key after the  
SCAN  
Press the  
10 seconds of each file.  
key to play the first  
file has been playing for 1 seconds will  
start the current file from the begin-  
ning.  
SEEK  
TRACK  
• Pressing the  
key before the  
file has been playing for 1 seconds will  
start the previous file.  
Selecting from the List  
Turn the TUNE knob left/right to  
search for the desired file.  
While playing, press the  
to pause and press  
play.  
button  
button to  
✽
NOTICE  
• Loading may require additional time if  
there are many files and folders within  
the USB and result in faulty list display  
or file searching. Normal operations  
will resume once loading is complete.  
• The device may not support normal  
operation when using a USB memory  
type besides (Metal Cover Type) USB  
Memory.  
Once you find the desired file, press the  
TUNE knob to start playing.  
4 228  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 229  
Features of your vehicle  
Searching Folders  
PTY  
USB Mode Menu  
✽
NOTICE  
Press the  
and search folders.  
key to select  
• When the ‘Folder File’ option is set as  
the default display within Display  
setup, the album/artist/file informa-  
tion are displayed as detailed file infor-  
mation.  
FOLDER  
Within this mode, you will have  
access to the Info, Random, Repeat,  
Copy and List features.  
• When the ‘Album Artist Song’ option  
is set as the default display, the folder  
name/file name are displayed as  
detailed file information.  
• The title, artist and album info are dis-  
played only when such information are  
recorded within the MP3 file ID3 tag.  
Once the desired folder is displayed,  
press the TUNE knob to select.  
Random  
Press the  
random order.  
button to play files in  
The first file within the selected folder will  
begin playing.  
Info  
Press the  
details about the current file.  
button to display  
Each time the button is pressed, the  
feature changes in order of Random  
Folder➟Random All➟Off.  
• Random Folder : Plays the files in the  
current folder in random order.  
• Random All : Plays all files in random  
order.  
4 229  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 230  
Features of your vehicle  
Repeat  
List  
Press the  
current file or folder.  
button to repeat the Press the  
button to display the  
file list screen.  
Each time the button is pressed, the  
feature changes in order of Repeat➟  
Repeat Folder ➟ Off.  
• Repeat (Icon) : Repeats the current  
file.  
• Repeat Folder (Icon) : Repeats all  
files within the current folder.  
Copying Files  
Press the  
current file into My Music.  
button to copy the  
Turn the  
TUNE knob left/right to  
search for files. Once the desired file  
is displayed, press the knob to select  
and play.  
✽
NOTICE  
Selecting another feature during copy-  
ing will display a pop-up asking whether  
you wish to cancel copying. To cancel,  
select 'Yes’.  
4 230  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 231  
Features of your vehicle  
(1) Mode  
(8) Repeat  
iPod MODE  
Displays currently operating mode  
Turns the Repeat feature on/off  
Basic Mode Screen  
(2) Operation State  
(9) List  
From Repeat / Random, displays the Moves to the list screen  
currently operating function  
(3) Song Index  
Displays the current song/total num-  
ber of songs  
(4) Song Info  
Displays information about the cur-  
rent song  
(5) Play/Pause  
Changes the play/pause state  
(6) Play Time  
Displays the current play time  
(7) Random  
Turns the Random feature on/off  
4 231  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 232  
Features of your vehicle  
Searching Categories  
Using iPod Mode  
✽
NOTICE  
Turn the TUNE knob left/right to  
search for the desired category.  
iPods with unsupported communication  
protocols may not properly operate in  
the audio system.  
Playing/Pausing iPod Songs  
Once an iPod is connected, the  
mode will automatically start and  
begin playing an iPod song.  
Changing Songs  
SEEK  
Press the  
previous or next song.  
key to move to the  
TRACK  
✽
NOTICE  
• Pressing the  
SEEK  
TRACK  
key after the  
song has been playing for 1 seconds  
will start the current song from the  
beginning.  
SEEK  
Once you find the desired category,  
press the  
play.  
• Pressing the  
key before the  
TRACK  
TUNE knob to select and  
song has been playing for 1 seconds  
will start the previous song.  
• Slight time differences may exist  
depending your iPod product.  
While playing, press the  
to pause and press  
play.  
button  
button to  
✽
NOTICE  
There are eight categories that can be  
searched, including Playlists, Artists,  
Albums, Genres, Songs, Composers,  
Audiobooks and Podcasts.  
Rewinding / Fast-forwarding Songs  
While playing, press and hold the  
SEEK  
key (over 0.8 seconds) to  
rewind or fast-forward the current song.  
TRACK  
4 232  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 233  
Features of your vehicle  
Repeat  
Category Menu  
Within the iPod Category menu, you  
iPod Mode Menu  
Press the  
current song. Press the button again  
to turn the repeat feature off.  
button to repeat the  
Within this mode, you will have  
access to the Random, Repeat and  
List features.  
will have access to the  
and features.  
, Home,  
• Repeat : Repeats the current song  
(1)  
: Displays the play screen  
Random  
(2) Home : Moves to the iPod root catego-  
ry screen  
Press the button to play songs  
in random order.  
(3)  
: Moves to the previous cate-  
gory  
Each time the button is pressed, the  
feature changes in order of Random  
Album➟Random All➟Off.  
✽
NOTICE  
• Random Album : Shuffle Album plays  
album in Random order.  
• If the search mode is accessed while  
playing a song, the most recently  
searched category is displayed.  
• Search steps upon initial connection  
may differ depending on the type of  
iPod device.  
• Random All : Plays all songs in  
Random order.  
4 233  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 234  
Features of your vehicle  
List  
AUX MODE  
✽
NOTICE  
Press the  
Category Menu.  
button to display the  
• If an external device connector is con-  
nected with the AUX terminal, then  
AUX mode will automatically operate.  
Once the connector is disconnected,  
the previous mode will be restored.  
• AUX mode can be used only when an  
external audio player (camcorder, car  
VCR, etc.) has been connected.  
Using AUX Mode  
MEDIA  
Press the  
key Select [AUX]  
• The AUX volume can be controlled  
separately from other audio modes.  
• Connecting a connector jack to the  
AUX terminal without an external  
device will convert the system to AUX  
mode, but only output noise. When an  
external device is not being used, also  
remove the connector jack.  
• When the external device power is  
connected to the power jack, playing  
the external device may output noise.  
In such cases, disconnect the power  
connection before use.  
Turn the TUNE knob left/right to  
search for the desired category.  
An external device can be connected to  
play music.  
Once you find the desired category,  
press the  
and play.  
TUNE knob to select  
Connecting an External Device  
External audio players (Camcorders, car  
VCR, etc.) can be played through a ded-  
icated cable.  
• Fully insert the AUX cable to the AUX  
jack upon use.  
4 234  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 235  
Features of your vehicle  
(1) Mode  
(7) Info  
MY MUSIC MODE  
Basic Mode Screen  
Displays currently operating mode  
Displays detailed information for the  
current file  
(2) Operation State  
(8) Random  
From Repeat / Random / Scan, dis-  
plays the currently operating function Turns the Random feature on/off  
(3) File Index (9) Repeat  
Displays the current file/total number Turns the Repeat feature on/off  
of files  
(10) Delete  
(4) File Info  
Deletes the current file  
Displays information about the cur-  
rent file  
(11) List  
Moves to the list screen  
(5) Play/Pause  
Changes the play/pause state  
(6) Play Time  
Displays the current play time  
4 235  
JD eng 4c(~265).QXP 3/4/2015 4:48 PM Page 236  
Features of your vehicle  
Using My Music Mode  
Scan  
✽
NOTICE  
• Pressing the  
SEEK  
TRACK  
SCAN  
key after the  
Press the  
10 seconds of each file.  
key to play the first  
file has been playing for 1 seconds will  
start the current file from the begin-  
ning.  
Playing/Pausing My Music Files  
SEEK  
TRACK  
• Pressing the  
key before the  
file has been playing for 1 seconds will  
start the previous file.  
Selecting from the List  
Turn the TUNE knob left/right to  
search for the desired file.  
While playing, press the  
to pause and press  
play.  
button  
button to  
✽
NOTICE  
If there are no files saved within My  
Music, the [My Music] button will be  
disabled.  
Once you find the desired file, press the  
TUNE knob to start playing.  
Changing Files  
SEEK  
Press the  
the previous or next file.  
key to move to  
TRACK  
Rewinding / Fast-forwarding Files  
While playing, press and hold the  
key (over 0.8 seconds) to  
rewind or fast-forward the current file.  
SEEK  
TRACK  
4 236  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 237  
Features of your vehicle  
Repeat  
My Music Mode Menu  
List Menu  
Press the  
current song. Press the button again  
to turn the repeat feature off.  
button to repeat the  
Within this mode, you will have  
access to the Info, Random, Repeat,  
Delete and List features.  
From the List screen, it is possible to  
delete files you previously saved into  
My Music.  
Deleting Files  
Press the  
current file.  
button to delete the  
button to display the  
List  
Press the  
file list screen.  
Info  
Press the button or individually  
select the files you want to delete. Once  
Press the  
details about the current file.  
button to display  
files are selected, the  
button and  
buttons will be enabled.  
✽
NOTICE  
(1)  
: Moves to the previous screen  
The title, artist and album info are dis-  
played only when such information is  
recorded within the MP3 file ID3 tag.  
(2) Sellect All: Selects all files  
(3) Unsellet All: Deselects all selected  
files  
Turn the  
TUNE knob left/right to  
Random  
(4) Delete: Deletes selected files  
search for files. Once the desired file is  
displayed, press the knob to select and  
play.  
Press the  
button to play files in  
random order. Press the button again  
to turn the Random feature off.  
4 237  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 238  
Features of your vehicle  
®
Bluetooth Wireless Technology  
AUDIO MODE  
After selecting the files you want to  
delete, press the  
the selected files.  
✽
NOTICE - USING THE  
Bluetooth® Wireless  
Technology Audio Mode  
button to delete  
• Bluetooth® Wireless Technology Audio  
Mode can be used only when a  
Bluetooth® Wireless Technology  
phone has been connected.  
• Bluetooth® Wireless Technology Audio  
Mode will not be available when con-  
necting mobile phones that do not  
support this feature.  
• While Bluetooth® Wireless Technology  
Audio is playing, if the Bluetooth®  
Wireless Technology phone is connect-  
ed, then the music will also stop.  
Using Bluetooth® Wireless  
Technology Audio Mode  
✽
NOTICE  
• If there is memory available, up to  
6,000 files can be saved.  
Playing/Pausing Bluetooth® Wireless  
Technology Audio  
Once a Bluetooth® Wireless Technology  
device is connected, the mode will auto-  
matically start.  
• Identical files cannot be copied more  
than 1,000 times.  
• To check memory information, go to  
SETUP  
[ S y s t e m ] [ M e m o r y  
Information]  
• Moving the Track up/down while  
Bluetooth®  
playing  
Wireless  
Technology audio mode may result in  
pop noises in some mobile phones.  
• Bluetooth® Wireless Technology  
streaming audio may not be support-  
ed in some mobile phones.  
• When returning to Bluetooth®  
Wireless Technology Audio mode  
after ending a call, the mode may not  
automatically restart in some mobile  
phones.  
While playing, press the  
pause and press  
button to  
button to play.  
• Receiving an incoming call or making  
an outgoing call while playing  
Bluetooth® Wireless Technology Audio  
may result in audio interference.  
4 238  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 239  
Features of your vehicle  
✽
✽
NOTICE  
NOTICE  
The play/pause feature may operate dif- • If the Bluetooth® Wireless Technology  
ferently depending on the mobile phone.  
audio is not operating properly, check  
whether the feature is turned off at  
SETUP  
Changing Files  
[Phone]  
[Audio stream-  
SEEK  
ing]. If the feature is off, turn back on  
and try again.  
Press the  
the previous or next file.  
TRACK  
key to move to  
• If music is not yet playing from your  
mobile device after converting to  
Bluetooth® Wireless Technology  
Audio mode, pressing the play button  
once may start playing the mode.  
Check to see that music is playing  
from the Bluetooth® Wireless  
Technology device after converting to  
Bluetooth® Wireless Technology Audio  
Mode.  
Setting Connection  
If a Bluetooth® Wireless Technology  
device has not been connected, press  
SETUP  
the  
key [Phone] button to  
display the Bluetooth® Wireless  
Technology connection screen.  
It is possible to use the pair phone, con-  
nect/disconnect and delete features from  
your Bluetooth® Wireless Technology  
phone.  
4 239  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 240  
Features of your vehicle  
Bluetooth® Wireless Technology  
• Bluetooth® Wireless Technology  
CAUTION  
• Bluetooth® Wireless Technology  
Handsfree is feature that  
Handsfree refers to a device which  
allows the user to conveniently  
make phone calls with Bluetooth®  
Using Bluetooth® Wireless  
Technology Handsfree  
a
enables drivers to practice safe  
driving. Connecting the car audio  
Wireless  
phones through the audio system.  
Technology  
mobile  
system with  
a
Bluetooth®  
• Bluetooth® Wireless Technology  
refers to a short-distance wireless  
networking technology which uses a  
2.45GHz frequency to connect vari-  
ous devices within a certain distance.  
• Supported within PCs, external  
Wireless Technology phone  
allows the user to conveniently  
make calls, receive calls, and  
manage the phone book. Before  
using the Bluetooth® Wireless  
Technology, carefully read the  
contents of this user’s manual.  
devices,  
Bluetooth®  
Wireless  
• Excessive use or operations  
while driving may lead to negli-  
gent driving practices and be the  
cause of accidents.  
Technology phones, PDAs, various  
electronic devices, and automotive  
environments, Bluetooth® Wireless  
Technology allows data to be trans-  
mitted at high speeds without hav-  
ing to use a connector cable.  
• Do not operate the device exces-  
sively while driving.  
• Viewing the screen for prolonged  
periods of time is dangerous and  
may lead to accidents. When driv-  
ing, view the screen only for short  
periods of time.  
4 240  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 241  
Features of your vehicle  
(Continued)  
(Continued)  
✽
NOTICE - USING UPON  
CONNECTING Bluetooth®  
Wireless Technology PHONE  
- To turn off the Bluetooth® Wireless  
Technology feature in your car audio  
SETUP  
• Bluetooth® Wireless Technology fea-  
tures supported within the vehicle are  
as follows. Some features may not be  
supported depending on your  
Bluetooth® Wireless Technologydevice.  
- Answering and placing Bluetooth®  
Wireless Technology Handsfree calls  
- Menu operation during call (Switch  
to Private, Switch to call waiting,  
Outgoing volume)  
system, go to  
[turn off] the Bluetooth® Wireless  
Technology feature.  
> [Phone] and  
• Before connecting the car audio system  
with the mobile phone, check to see that  
the mobile phone supports Bluetooth®  
Wireless Technology features.  
• Park the vehicle when connecting the  
car audio system with your mobile  
phone.  
• Even if the phone supports Bluetooth®  
Wireless Technology, the phone will  
not be found during device searches if  
the phone has been set to hidden state  
or the Bluetooth® Wireless Technology  
power is turned off. Disable the hidden  
state or turn on the Bluetooth®  
Wireless Technology power prior to  
searching/connecting with the car  
audio system.  
• If you do not want to automatically  
connect your Bluetooth® Wireless  
Technology phone, try the following.  
1. Turn off the Bluetooth® Wireless  
Technology feature in your mobile  
phone.  
• Bluetooth® Wireless Technology con-  
nection may become intermittently  
disconnected in some mobile phones.  
Follow these steps to try again.  
1. Turn the Bluetooth® Wireless  
Technology function within the  
mobile phone off/on and try again.  
2. Turn the mobile phone power  
Off/On and try again.  
- Download Call History  
- Download Mobile Phone book  
- Phone book/Call HistoryAuto Download  
- Bluetooth® Wireless Technology  
device auto connection - Bluetooth®  
Wireless Technology Audio  
• It is possible to pair up to five  
Bluetooth® Wireless Technology  
devices to the car system.  
• Only one Bluetooth® Wireless  
Technology device can be connected at  
a time.  
3 Completely remove the mobile  
phone battery, reboot, and then  
again.  
4. Reboot the audio system and try  
again.  
5. Delete all paired devices, pair and • Other devices cannot be paired while a  
- For more information on Bluetooth®  
Wireless Technology features within  
your mobile, refer to your mobile  
phone user’s manual.  
2. Turn off the Bluetooth® Wireless  
Technology feature in your car  
audio system.  
try again.  
• The Handsfree call volume and quali-  
ty may differ depending on the mobile • When a Bluetooth® Wireless Technology  
Bluetooth® Wireless Technologydevice  
is already connected.  
phone.  
device is being connected, the connec-  
tion process cannot be canceled.  
(Continued)  
(Continued)  
(Continued)  
4 241  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 242  
Features of your vehicle  
Bluetooth® Wireless Technology  
(Continued)  
• Only Bluetooth® Wireless Technology  
PHONE  
Pairing  
the Steering Remote Controller  
Key /  
Key on  
Handsfree and Bluetooth® Wireless  
Technology audio related features will Pairing a Bluetooth® Wireless  
When No Devices have been Paired  
operate within this system.  
Technology wireless technology  
Device  
• Normal operation is possible only for  
devices that support Handsfree or  
audio features, such as a Bluetooth®  
Wireless Technology mobile phone or  
a Bluetooth® Wireless Technology  
audio device.  
• Only one function can be used at a time  
between the Bluetooth® Wireless  
Technology Handsfree and Bluetooth®  
Wireless Technology audio. (While  
playing Bluetooth® Wireless Technology  
audio, streaming will end upon entering  
the Bluetooth® Wireless Technology  
phone screen.)  
PHONE  
1. Press the  
key or the  
key on the steering remote con-  
troller. The following screen is dis-  
played.  
What is Bluetooth® Wireless  
Technology Pairing?  
2. Press the button to enter the  
Pair Phone screen.  
Pairing refers to the process of syn-  
chronizing your Bluetooth® Wireless  
Technology phone or device with the  
car audio system for connection.  
Pairing is necessary to connect and  
use the Bluetooth® Wireless  
Technology feature.  
• If a connected Bluetooth® Wireless  
Technology device becomes discon-  
nected for various reasons, such as  
being out of range, turning the device  
OFF, or  
a
Bluetooth® Wireless  
Technology communication error,  
Bluetooth® Wireless Technology  
devices are automatically searched  
and connected.  
• Placing the audio system within an  
electromagnetic environment may  
result in noise interference.  
4 242  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 243  
Features of your vehicle  
(1) Device : Name of device as shown  
when searching from your Bluetooth®  
Wireless Technology device  
Pairing through [PHONE] Setup  
✽
NOTICE  
SETUP  
Press the  
key  
Select  
[Phone] Select [Pair Phone]  
Select TUNE knob  
(2) Passkey : Passkey used to pair the  
device  
3. From your Bluetooth® Wireless  
Technology device (i.e. Mobile  
Phone), search and select your  
car audio system.  
4. After a few moments, a screen is  
displayed where the passkey is  
entered.  
• If Bluetooth® Wireless Technology  
devices are paired but none are cur-  
PHONE  
rently connected, pressing the  
key or the  
Here, enter the passkey “0000” to  
pair your Bluetooth® Wireless  
Technology device with the car  
audio system.  
key on the  
1. The following steps are the same as  
the steps described in the “When No  
Devices have been Paired” section.  
steering remote controller displays the  
following screen. Press the [Pair] but-  
ton to pair a new device or press the  
[Connect] to connect a previously pair  
device.  
5. Once pairing is complete, the fol-  
lowing screen is displayed.  
4 243  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 244  
Features of your vehicle  
From the paired phone list, select the  
device you want to connect and press the  
button.  
Connecting a Device  
✽
NOTICE  
• The waiting period during phone pair-  
ing will last for one minute. The pair-  
ing process will fail if the device is not  
paired within the given time. If the  
pairing process fails, you must start  
the process from the beginning.  
SETUP  
Press the key Select  
[Phone] Select [Paired Phone List]  
• Generally, most Bluetooth® Wireless  
Technology devices will automatically  
connect once pairing is complete.  
However, some devices may require a  
separate verification process to con-  
nect. Check to see whether Bluetooth®  
Wireless Technology has been proper-  
ly connected within your mobile  
phone.  
(1) Connected Phone : Device that is cur-  
rently connected  
• List of paired Bluetooth® Wireless  
Technology devices can be viewed at  
SETUP  
(2) Paired Phone : Device that is paired  
but not connected  
[Phone] [Paired  
Phone  
List].  
4 244  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 245  
Features of your vehicle  
Changing Priority  
From the paired phone list, select Disconnecting a Device  
the phone you want to change to the  
highest priority, then press the  
button from the Menu. The selected  
device will be changed to the high-  
est priority.  
What is Priority?  
SETUP  
Press the key Select  
[Phone] Select [Paired Phone List]  
It is possible to pair up to five  
Bluetooth® Wireless Technology  
devices with the car audio system.  
As a result, the “Change Priority’ fea-  
ture is used to set the connection pri-  
ority of paired phones. However, the  
most recently connected phone will  
always be set as the highest priority.  
SETUP  
Press the  
Select [Paired Phone List]  
key Select [Phone]  
From the paired phone list, select the  
currently connected device and press the  
button.  
✽
NOTICE  
When a device is currently connected,  
even if you change the priority to a differ-  
ent device, the currently connected phone  
will always be set as the highest priority.  
4 245  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 246  
Features of your vehicle  
USING Bluetooth® Wireless  
Technology  
(4) Setup : Displays Phone related set-  
tings  
Deleting a Device  
SETUP  
Press the key Select  
[Phone] Select [Paired Phone List]  
✽
NOTICE  
Phone Menu Screen  
• If you press the [Call History] button  
but there is no call history data, a  
prompt is displayed which asks  
whether to download call history data.  
• If you press the [Phone book] button  
but there is no phone book data, a  
prompt is displayed which asks  
whether to download phone book data.  
.
Phone Menus  
With  
a
Bluetooth®  
Technology device connected, press  
Wireless  
PHONE  
the  
menu screen.  
key to display the Phone  
• This feature may not be supported in  
some mobile phones. For more infor-  
mation on download support, refer to  
your mobile phone user’s manual.  
From the paired phone list, select the  
device you want to delete and press the  
button.  
✽
NOTICE  
• When deleting the currently connect-  
ed device, the device will automatical-  
ly be disconnected to proceed with the  
deleting process.  
(1) Dial Number : Displays the dial  
screen where numbers can be dialed  
to make calls  
• If  
a
paired Bluetooth® Wireless  
Technology device is deleted, the  
device’s call history and phone book  
data will also be deleted.  
• To re-use a deleted device, you must  
pair the device again.  
(2) Call History : Device that is currently  
connected  
(3) Phone book : Displays the Phone  
book list screen  
4 246  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 247  
Features of your vehicle  
Calling by Dialing a Number  
Answering Calls  
✽
NOTICE  
• When the incoming call pop-up is dis-  
played, most Audio and SETUP mode  
features will not operate. Only the call  
volume can be operated.  
• The telephone number may not be  
properly displayed in some mobile  
phones.  
Answering a Call  
PHONE  
Press the  
Number]  
key Select [Dial  
Answering a call with a Bluetooth®  
Wireless Technology device connect-  
ed will display the following screen.  
• When a call is answered with the  
mobile phone, the call mode will auto-  
matically convert to Private mode.  
(1) Dial Pad : Used to enter phone num-  
ber  
(1) Caller : Displays the other part’s  
name when the incoming caller is  
saved within your phone book  
(2) Call : If a number has been entered,  
calls the number If no number has  
been entered, switches to call history  
screen  
(2) Incoming Number : Displays the  
incoming number  
(3) End : Deletes the entered phone  
number  
(3) Accept : Accept the incoming call  
(4) Reject : Reject the incoming call  
(4) Delete : Deletes entered numbers  
one digit at a time  
4 247  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 248  
Features of your vehicle  
During a Handsfree Call  
Call History  
✽
NOTICE  
• The call history list will display up to  
30 outgoing, incoming, and missed  
calls.  
PHONE  
Press the  
History]  
key Select [Call  
• Upon downloading call histories, pre-  
viously saved histories are deleted.  
• Incoming calls with hidden caller IDs  
will not be saved in the call history  
list.  
• Previously saved phone book entries  
are stored even if a device is discon-  
nected and re-connected.  
• The download feature may not be sup-  
ported in some mobile phones. Check  
to see that the Bluetooth® Wireless  
Technology device supports the down-  
load feature.  
(1) Caller : Displays the other party’s  
name if the incoming caller is saved  
within your phone book  
A list of incoming, outgoing and missed  
calls is displayed.  
(2) Incoming Number : Displays the  
incoming number  
Press the [Download] button to download  
the call history.  
(3) Call time : Displays the call time  
(4) End : Ends call  
(1) Call History :  
(5) Private : Converts to Private mode  
- Displays recent calls (call history)  
- Connects call upon selection  
(6) Out Vol. : Sets call volume as heard  
by the other party  
(2) Download : Download Recent Call  
History  
(7) Mute : Turns Mic Mute On/Off  
✽
NOTICE  
If the mic is muted, the other party will  
not be able to hear your voice.  
4 248  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 249  
Features of your vehicle  
Phone Book  
✽
NOTICE  
• Up to 1,000 phone book entries can be  
copied into car phone book.  
PHONE  
Press the  
[Phone book]  
key Select  
• Upon downloading phone book data,  
previously saved phone book data will  
be deleted.  
• Downloading is not possible if the  
phone book download feature is  
®
turned off within the Bluetooth  
Wireless Technology device. Also, some  
devices may require device authoriza-  
tion upon attempting to download. If  
downloading cannot be normally con-  
®
ducted, check the Bluetooth Wireless  
Technology device setting or the screen  
state.  
• Caller ID information will not be dis-  
played for unsaved callers.  
The list of saved phone book entries is  
displayed. Press the [Download] button  
to download the call history.  
• The download feature may not be sup-  
ported in some mobile phones. Check  
®
to see that the Bluetooth Wireless  
Technology device supports the down-  
load feature.  
(1) Contact List :  
- Displays downloaded phone book  
entries  
- Connects call upon selection  
(2) Download : Download phone book  
entries  
4 249  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 250  
Features of your vehicle  
• Phone related voice commands can be  
®
✽
NOTICE - USING THE Voice  
Recognition  
used only when  
a
Bluetooth  
Wireless Technology device is con-  
nected.  
• When using the voice recognition fea-  
ture, only commands listed within the  
user's manual are supported.  
• Be aware that during the operation of  
the voice recognition system, pressing  
• When making calls by stating a name,  
the corresponding contact must be  
downloaded and stored within the  
audio system.  
any key other than the  
key or  
®
• After downloading the Bluetooth  
touching the screen will terminate  
voice recognition mode.  
Wireless Technology phone book, it  
takes some times to convert the phone  
book data into voice information.  
During this time, voice recognition  
may not properly operate.  
• Pronounce the voice commands natu-  
rally and clearly as if in a normal con-  
versation.  
• For superior voice recognition per-  
formance, position the microphone  
used for voice recognition above the  
head of the driver’s seat and maintain  
a proper position when saying com-  
mands.  
• Within the following situations, voice  
recognition may not function properly  
due to external sound.  
- When the windows and sunroof are  
open  
- When the wind of the cooling / heat-  
ing device is strong  
- When entering and passing through  
tunnels  
- When driving on rugged and uneven  
roads  
- During severe rain (heavy rains,  
windstorms)  
4 250  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 251  
Features of your vehicle  
If voice recognition is in [Normal Mode],  
then the system will say “Please say a  
command. Beep~”  
Skipping Prompt Messages  
VOICE RECOGNITION  
Using Voice Recognition  
While prompt message is being stat-  
ed Shortly press the key on the  
• If voice recognition is in [Expert Mode], steering remote controller (under 0.8  
then the system will only say a “Beep~” seconds)  
Starting Voice Recognition  
• To change the Normal Mode/Expert  
SETUP  
The prompt message is immediately  
ended and the beep tone will sound.  
After the “beep”, say the voice command.  
Shortly press the  
key on the  
Mode setting, go to  
[Prompt Feedback].  
[System]  
steering remote controller .Say a  
command  
✽
NOTICE  
Re-starting Voice Recognition  
For proper recognition, say the com-  
mand after the voice instruction and  
beep tone.  
While system waits for a command  
Shortly press the  
key on the  
steering remote controller (under 0.8  
seconds)  
The command wait state is immediately  
ended and the beep ton will sound. After  
the “beep”, say the voice command.  
4 251  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 252  
Features of your vehicle  
ENDING VOICE RECOGNITION  
While Voice Recognition is operating  
Press and hold the  
key on the  
steering remote controller (over 0.8  
seconds)  
✽
NOTICE  
• While using voice command, pressing  
a steering wheel remote control or a  
different key will end voice command.  
• In a state where the system is waiting  
for a voice command, say “cancel” or  
“end” to end voice command.  
• In a state where the system is waiting  
for a voice command, press and hold  
the key on the steering remote  
controller to end voice command.  
4 252  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 253  
Features of your vehicle  
Pop-up Mode  
Display Settings  
SETUP  
SETUP  
Press the  
[Display] Select [Pop-up Mode]  
key Select  
Starting Mode  
Adjusting the Brightness  
SETUP  
SETUP  
Press the  
Setup screen.  
key to display the Press the  
key Select  
[Display] Select [Brightness]  
This feature is used to display the Pop-up  
Mode screen when entering radio and  
media modes.  
You can select and control options relat-  
ed to [Display], [Sound], [Phone] and  
[System].  
Use the  
,
buttons to adjust the  
When this feature is turned on, pressing  
RADIO  
screen brightness or set the Brightness  
on Automatic, Day, or Night mode.  
MEDIA  
key will display  
the  
the Pop-up Mode screen.  
or  
Default  
Press the  
button to reset.  
✽
NOTICE  
(1) Automatic : Adjusts the brightness  
automatically  
The media Pop-up Mode screen can be  
displayed only when two or more media  
modes have been connected.  
(2) Day : Always maintains the bright-  
ness on high  
(3) Night: Always maintains the bright-  
ness on low  
4 253  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 254  
Features of your vehicle  
Scroll Text  
MP3 Information Display  
SETUP  
Sound Settings  
Sound Settings  
Press the  
[Display] Select [Song Info]  
key Select  
SETUP  
Press the  
[Display] Select [Scroll text]  
key Select  
SETUP  
Press the  
[Sound] Select [Audio Setting]  
key Select  
This feature is used to change the infor-  
mation displayed within USB and MP3  
CD modes.  
This feature is used to scroll text dis-  
played on the screen when it is too long  
to be displayed at once.  
When turned on, the text is repeatedly  
scrolled. When turned off, the text is  
scrolled just once.  
(1) Folder File : Displays file name and  
folder name  
(2) Album Artist Song : Displays album  
name/artist name/song  
Use the  
adjust the Fader/Balance settings.  
Use the buttons to adjust the  
Bass/Middle/Treble settings.  
,
,
,
buttons to  
,
Default  
Press the  
button to reset.  
4 254  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 255  
Features of your vehicle  
SDVC (Speed Dependent Volume  
Control)  
Voice Recognition Setting  
SETUP  
Touch Screen Beep  
SETUP  
Press the  
[Sound] Select [Volume Dialogue]  
key Select Press the  
key Select  
SETUP  
Press the  
key Select  
[Sound] Select [Touch Screen  
Beep]  
[Sound] Select [Speed Dependent  
Vol.]  
Use the  
Volume Dialog.  
,
buttons to adjust the  
This feature is used to turn the touch  
screen beep on/off.  
The volume level is controlled automati-  
cally according to the vehicle speed.  
SDVC can be set by selecting from  
Off/Low/Mid/High.  
4 255  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 256  
Features of your vehicle  
Bluetooth® Wireless Technology  
Setting  
Viewing Paired Phone List  
SETUP  
(
4) Change Priority : Sets currently select-  
ed phone to highest connection priority  
Press the key Select  
[Phone] Select [Paired Phone List]  
Pairing a New Device  
✽ NOTICE BEFORE DOWN-  
LOADING PHONE BOOKS  
• Only phone books within connected  
phones can be downloaded. Also  
check to see that your mobile phone  
supports the download feature.  
• To learn more about whether your  
mobile phone supports phone book  
downloads, refer to your mobile  
phone user’s manual.  
SETUP  
Press the  
[Phone] Select [Pair Phone]  
key Select  
• The Phone book for only the connect-  
ed phone can be downloaded. Before  
downloading, check to see whether  
your phone supports the download  
feature.  
This feature is used to view mobile  
phones that have been paired with the  
audio system. Upon selecting a paired  
phone, the setup menu is displayed.  
Bluetooth® Wireless Technology devices  
can be paired with the audio system.  
For more information, refer to the “Setting  
Bluetooth®  
Connection” section within Bluetooth®  
Wireless Technology.  
For more information, refer to the “Pairing  
through Phone Setup” section within  
Bluetooth® Wireless Technology.  
Wireless  
Technology  
(1)  
: Moves to the previous screen  
Phone  
(2) Connect/Disconnect  
:
Connect/ disconnects currently  
selected phone  
(3) Delete : Deletes the currently select-  
ed phone  
4 256  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 257  
Features of your vehicle  
Downloading Phone books  
Auto Download (Phone Book)  
SETUP  
Audio Streaming  
SETUP  
SETUP  
Press the  
[Phone] Select  
Download]  
key Select Press the  
key Select Press the  
key Select  
[Phone] Select [Audio Streaming]  
[Phone  
book [Phone] Select [Auto Download]  
This feature is used to automatically  
When Audio Streaming is turned on, you  
can play music files saved in your  
Bluetooth® Wireless Technology device  
from the car.  
The Phone book is downloaded from the  
mobile phone and the download  
progress is displayed.  
download mobile phone book entries  
once a Bluetooth® Wireless Technology  
phone is connected.  
✽
✽
NOTICE  
• Up to 1,000 phone book entries can be • The Auto Download feature will  
NOTICE  
copied into car phone book.  
• Up to 1,000 phone book entries can be  
saved for each paired device.  
• Upon downloading phone book data,  
previously saved phone book data will  
be deleted. However, Phone book  
download mobile phone book entries  
every time the phone is connected.  
The download time may differ  
depending on the number of saved  
phone book entries and the communi-  
cation state.  
entries saved to other paired phones • When downloading a phone book,  
are not deleted.  
first check to see that your mobile  
phone supports the phone book down-  
load feature.  
4 257  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 258  
Features of your vehicle  
Outgoing Volume  
SETUP  
Turning Bluetooth System Off  
SETUP  
✽
NOTICE  
To turn Bluetooth® Wireless Technology  
back on, go to  
press “Yes”.  
Press the key Select  
[Phone] Select [Outgoing Volume]  
Press the  
key Select  
SETUP  
[Phone] and  
[Phone] Select [Bluetooth System  
Off]  
Once Bluetooth® Wireless Technology is  
Bluetooth®  
Wireless  
CAUTION  
Bluetooth® Wireless Technology  
audio streaming may not be sup-  
turned  
off,  
Technology related features will not be  
supported within the audio system.  
ported  
in  
some  
Wireless Technology phones.  
Bluetooth®  
Use the  
outgoing volume level.  
,
buttons to adjust the  
4 258  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 259  
Features of your vehicle  
Voice Recognition Mode Setting  
SETUP  
Language  
System Setting  
SETUP  
Press the  
key Select Press the  
key Select  
[System] Select [Voice Recognition [System] Select [Language]  
System]  
Memory Information  
SETUP  
Press the  
key Select  
[System] Select [Memory Information]  
This feature is used to change the sys-  
tem and voice recognition language.  
This feature is used to select the desired  
prompt feedback option from Normal and  
Expert.  
If the language is changed, the system  
will restart and apply the selected lan-  
guage.  
This feature displays information related  
to system memory.  
(1) Normal : When using voice recogni-  
tion, provides detailed guidance  
prompts  
(1) Using : Displays capacity currently in  
use  
(2) Capacity : Displays total capacity  
(2) Expert : When using voice recogni-  
tion, omits some guidance prompts  
✽
NOTICE  
• Voice Recognition is depend on the  
Audio System.  
4 259  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 260  
Features of your vehicle  
• End voice command.  
❈ Illustration on using voice commands  
Shortly pressing the  
key (under 0.8 seconds):  
• Starting voice command.  
Please say a command  
Ding~  
Shortly pressing the  
key (under 0.8 seconds):  
Ding~  
Please say a command  
Phone book  
More Help  
Phone book.  
Please say the name of the phone book you  
want to call.  
More Help.  
You can say Radio, FM, AM, Media, CD, USB, Aux,  
My Music, iPod, Bluetooth Audio, Phone, Call  
History or Phone book. Please say a command.  
Ding~  
Cancel  
• Skipping Voice Recognition  
Di-Ding~(Cancel Sound)  
Shortly pressing the  
0.8 seconds):  
key (under  
Please say a...  
Ding~  
Shortly pressing the  
(under 0.8 seconds)  
key  
More Help  
More Help.  
You can say Radio, FM, AM, Media, CD, USB, Aux,  
My Music, iPod, Bluetooth Audio, Phone, Call  
History or Phone book. Please say a command.  
4 260  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 261  
Features of your vehicle  
Voice Command List  
• Common Commands: These are commands that can be used in all situations. (However, some commands may not be support-  
ed in special circumstances.)  
Command  
More Help  
Function  
Command  
Function  
Provides guidance on commands that can be  
used anywhere in the system.  
FM  
•
•
When currently listening to the FM radio,  
maintains the current state.  
Help  
Provides guidance on commands that can be  
used within the current mode.  
When listening to a different mode, displays  
the most recently played FM screen.  
Call<Name>  
Phone  
Calls <Name> saved in phone book  
Ex) Call “John”  
FM1(FM One)  
FM2(FM Two)  
FMA  
Displays the FM1 screen.  
Displays the FM2 screen.  
Displays the FMA screen.  
Displays the AM screen.  
Displays the AMA screen.  
Provides guidance on Phone related com-  
mands. After saying this command, say “Call  
History”, “Phone book”, “Dial Number” to exe-  
cute corresponding functions.  
AM  
AMA  
FM Preset 1~6  
Plays the most recently played broadcast  
saved in FM Preset 1~6.  
Call History  
Phone book  
Displays the Call History screen.  
Displays the phone book screen. After saying  
this command, say the name of a phone book  
saved in the phone book to automatically con-  
nect the call.  
AM Preset 1~6  
FM 87.5~107.9  
Plays the broadcast saved in AM Preset 1~6.  
Plays the FM broadcast of the corresponding  
frequency.  
Dial Number  
Display the Dial number screen. After saying  
this command, you can say the number what  
you want to call.  
AM 530~1710  
Plays the AM broadcast of the corresponding  
frequency.  
TA on  
Enable Traffic Announcement  
Disable Traffic Announcement  
Enable RDS News feature  
Disable RDS News feature  
Redial  
Radio  
Connects the most recently called number.  
TA off  
•
When listening to the radio, displays the next  
radio screen. (FM1➟ FM2➟ FMA ➟ AM ➟  
AMA)  
News on  
News off  
•
When listening to a different mode, displays  
the most recently played radio screen.  
4 261  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 262  
Features of your vehicle  
Command  
Media  
Function  
Command  
Function  
Moves to the most recently played media  
screen.  
AUX (Auxiliary)  
Plays the connected external device.  
Bluetooth Audio Plays the music saved in connected  
Bluetooth® Wireless Technology device.  
Play Track 1~30 If a music CD has been inserted, plays the  
corresponding track.  
Mute  
Mutes the radio or music volume.  
Repeats the most recent comment.  
Ends voice command.  
CD  
Plays the music saved in the CD.  
Pardon?  
Cancel (Exit)  
Search CD  
Moves to the CD track or file selection screen.  
For audio CDs, move to the screen and say the  
track number to play the corresponding track.  
•
•
Moves to MP3 CD file selection screen. After  
manually operate the device to select and  
play music.  
USB  
Plays USB music.  
Search USB  
Moves to USB file selection screen. After  
manually operate the device to select and play  
music.  
iPod  
Plays iPod music.  
Search iPod  
Moves to the iPod file selection screen. After,  
manually operate the device to select and play  
music.  
My Music  
Plays the music saved in My Music.  
Search My Music Moves to My Music file selection screen. After  
manually operate the device to select and play  
music.  
4 262  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 263  
Features of your vehicle  
• FM/AM radio commands: Commands that can be used while  
listening to FM, AM radio.  
• Audio CD commands: Commands that can be used while  
listening to Audio CD.  
Command  
Preset 1~6  
Auto Store  
Function  
Command  
Region off  
Function  
Disable Region feature  
Plays the broadcast saved in Preset 1~6.  
Automatically selects radio broadcast fre-  
quencies with superior reception and saves in  
Presets 1~6.  
Program Type  
Moves to the RDS Program type selection  
screen. After, manually operate the device to  
select a desired program type.  
Preset Save 1~6 Saves the current broadcast frequency to  
Preset 1~6.  
Random  
Randomly plays the tracks within the CD.  
Random Off  
Cancels random play to play tracks in sequen-  
tial order.  
Seek up  
Plays the next receivable broadcast.  
Seek down  
Next Preset  
Plays the previous receivable broadcast.  
Repeat  
Repeats the current track.  
Selects the preset number next to the most  
recently selected preset. (Example:When cur-  
rently listening to preset no. 3, then preset no.  
4 will be selected.)  
Repeat Off  
Cancels repeat play to play tracks in sequen-  
tial order.  
Next Track  
Previous Track  
Scan  
Plays the next track.  
Plays the previous track.  
Previous Preset Selects the preset number previous to the  
most recently selected preset. (Example:  
When currently listening to preset no. 3, then  
preset no. 2 will be selected.)  
Scans the tracks from the next track for 10  
seconds each.  
Track 1~30  
Plays the desired track number.  
Search Track  
Moves to the track selection screen. After, say  
the track name to play the corresponding track.  
Scan  
Scans receivable frequencies from the current  
broadcast and plays for 10 seconds each.  
Information  
Displays the information screen of the current  
track.  
Preset Scan  
Moves to the next preset from the current  
present and plays for 10 seconds each.  
AF on  
AF off  
Region  
Enable Alternative Frequency feature  
Disable Alternative Frequency feature  
Enable Region feature  
4 263  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 264  
Features of your vehicle  
• MP3 CD / USB commands: Commands that can be used  
while listening to music files saved in CD and USB.  
• iPod Commands: Commands that can be used while playing  
iPod.  
Command  
Function  
Command  
All Random  
Random  
Function  
Random  
Randomly plays the files within the current  
folder.  
Randomly plays all saved songs.  
Randomly plays the songs within the current  
category.  
All Random  
Random Off  
Randomly plays all saved files.  
Cancels random play to play files in sequential  
order.  
Random Off  
Cancels random play to play songs in sequen-  
tial order.  
Repeat  
Repeats the current file.  
Repeat  
Repeats the current song.  
Folder Repeat  
Repeat Off  
Repeats all files in the current folder.  
Repeat Off  
Cancels repeat play to play songs in sequen-  
tial order.  
Cancels repeat play to play files in sequential  
order.  
Next Song  
Plays the next song.  
Next File  
Previous File  
Scan  
Plays the next file.  
Previous Song  
Search Song  
Information  
Plays the previous song.  
Moves to the song selection screen.  
Plays the previous file.  
Scans the files from the next files for 10 sec-  
onds each.  
Displays the information screen of the current  
song.  
Search File  
Search Folder  
Information  
Moves to the file selection screen.  
Moves to the folder selection screen.  
Displays the information screen of the current  
file.  
Copy  
Copies the current file into My Music.  
4 264  
JD eng 4c(~265).QXP 3/4/2015 4:49 PM Page 265  
Features of your vehicle  
®
• My Music Commands: Commands that can be used while  
playing My Music.  
• Bluetooth Wireless Technology Audio Commands:  
Commands that can be used while playing Phone Music.  
Command  
Random  
Function  
Command  
Play  
Pause  
Function  
Plays the currently paused song.  
Pauses the current song.  
Randomly plays all saved files.  
Random Off  
Cancels random play to play files in sequential  
order.  
Repeat  
Repeats the current file.  
Repeat Off  
Cancels repeat play to play files in sequential  
order.  
Next File  
Previous File  
Scan  
Plays the next file.  
Plays the previous file.  
Scans the files from the next files for 10 sec-  
onds each.  
Search File  
Information  
Moves to the file selection screen.  
Displays the information screen of the current  
file.  
Delete  
Deletes the current file. You will bypass an  
additional confirmation process.  
Delete All  
Deletes all files saved in My Music. You will  
bypass an additional confirmation process.  
4 265  

Related Topics

Features of your vehicle
Keys Record your key number Key operations Immobilizer system Remote keyless entry Remote keyless entry system operations Transmitter precautions Battery replacement Smart key Smart key function Smart key precautions Door lock/unlock in an emergency situation Theft-alarm system Armed stage Theft-alarm stage Disarmed stage Door locks From outside From inside Deadlocks Door lock/unlock features Child-protector rear door lock Tailgate Opening the tailgate Closing the tailgate Emergency tailgate safety release Windows Power windows Manual windows Hood Opening the hood Closing the hood Fuel filler lid Opening the fuel filler lid Closing the fuel filler lid Panorama sunroof Sunshade Sliding the sunroof Tilting the sunroof Closing the sunroof Resetting the sunroof Steering wheel Electronic power steering Tilt and telescopic steering Heated steering wheel Horn Flex steering wheel Mirrors Inside rearview mirror Outside rearview mirror Instrument cluster Instrument panel illumination Gauges Manual transaxle shift indicator Automatic transaxle shift position indicator Double clutch transmission shift indicator Speed limiter indicator Odometer Trip computer LCD display information Warnings and indicators Rear parking assist system Operation Non-operational conditions Precautions Self-diagnosis Parking assist system Smart Parking Assist System(SPAS) Operating condition Non-operating condition How the system works Additional instructions(messages) System malfunction Rearview camera Hazard warning flasher Lighting Battery saver function Headlamp delay function Headlight (Headlamp) welcome function Static bending light Lighting control High-beam operation Turn signals and lane change signals Front fog light Rear fog light Daytime running light Headlight leveling device Adaptive Front Lighting System (AFLS) Wipers and washers Windshield wipers (front) Windshield washers (front) Interior lamp AUTO cut Map lamp Room lamp Vanity mirror lamp Luggage room lamp Glove box lamp Welcome system Headlamp welcome Interior light Puddle lamp Defroster Rear window defroster Heating and air conditioning Automatic heating and air conditioning Manual heating and air conditioning System operation Climate control air filter Checking the amount of air conditioner refrigerant and compressor lubricant Windshield defrosting and defogging Manual climate control system Automatic climate control system Clean air Storage compartment Center console storage Sliding armrest Glove box Cool box Sunglass holder Luggage tray Interior features Cigarette lighter Ashtray Cup holder Bottle holder Sunvisor Power outlet Aux, USB and iPod Clothes hanger Floor mat anchor(s) Luggage net (holder) Cargo area cover Barrier net Cargo security screen Luggage rail system Shopping bag holder Exterior features Mounting bracket for roof carrier Roof rack Antenna Audio remote control How car audio works

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot