Get Owner Maintenance Guide for Mazda Cx-5 SUV First Generation (2013-2016)

Maintenance and Care

Owner Maintenance

Owner Maintenance Precautions

The owner or a qualified service technician should make these vehicle inspections at the

indicated intervals to ensure safe and dependable operation.

Bring any problem to the attention of an Authorized Mazda Dealer or qualified service

technician as soon as possible.

When Refueling

l

Brake and clutch fluid level (page 6-32)

Engine coolant level (page 6-30)

Engine oil level (page 6-30)

Washer fluid level (page 6-33)

l

At Least Monthly

Tire inflation pressures (page 6-43)

At Least Twice a Year (For Example, Every Spring and Fall)

You can do the following scheduled maintenance items if you have some mechanical

ability and a few basic tools and if you closely follow the directions in this manual.

l

Engine coolant (page 6-30)

Engine oil (page 6-27)

l

Improper or incomplete service may result in problems. This section gives instructions only

for items that are easy to perform.

As explained in the Introduction (page 6-2), several procedures can be done only by a

qualified service technician with special tools.

Improper owner maintenance during the warranty period may affect warranty coverage.

Refer to Introduction (page 6-2) for owner's responsibility in protecting your investment.

For details, read the separate Mazda Warranty statement provided with the vehicle. If you

are unsure about any servicing or maintenance procedure, have it done by an Authorized

Mazda Dealer.

There are strict environmental laws regarding the disposal of waste oil and fluids. Please

dispose of your waste properly and with due regard to the environment.

We recommend that you entrust the oil and fluid changes of your vehicle to an Authorized

Mazda Dealer.

6-22

Maintenance and Care

Owner Maintenance

WARNING

Do not perform maintenance work if you lack sufficient knowledge and experience or

the proper tools and equipment to do the work. Have maintenance work done by a

qualified technician:

Performing maintenance work on a vehicle is dangerous if not done properly. You

can be seriously injured while performing some maintenance procedures.

If you must run the engine while working under the hood, make certain that you

remove all jewelry (especially rings, bracelets, watches, and necklaces) and all

neckties, scarves, and similar loose clothing before getting near the engine or cooling

fan which may turn on unexpectedly:

Working under the hood with the engine running is dangerous. It becomes even

more dangerous when you wear jewelry or loose clothing.

Either can become entangled in moving parts and result in injury.

Switch the ignition to off and make sure the fan is not running before

attempting to work near the cooling fan:

Working near the cooling fan when it is running is dangerous. The fan could

continue running indefinitely even if the engine has stopped and the engine

compartment temperature is high. You could be hit by the fan and seriously injured.

Do not leave items in the engine compartment:

After you have finished checking or doing servicing in the engine compartment, do

not forget and leave items such as tools or rags in the engine compartment.

Tools or other items left in the engine compartment could cause engine damage or a

fire leading to an unexpected accident.

6-23

Maintenance and Care

Owner Maintenance

3. Grasp the support rod in the padded

area and secure it in the support rod

hole indicated by the arrow to hold the

hood open.

Hood

WARNING

Always check that the hood is closed

and securely locked:

A hood that is not closed and

securely locked is dangerous as it

could fly open while the vehicle is

moving and block the driver's vision

which could result in a serious

accident.

Pad

Clip

qOpening the Hood

1. With the vehicle parked, pull the

release handle to unlock the hood.

Support rod

Release handle

2. Insert your hand into the hood opening,

slide the latch lever to the right, and lift

up the hood.

6-24

Maintenance and Care

Owner Maintenance

qClosing the Hood

1. Check under the hood area to make

certain all filler caps are in place and

all loose items (e.g. tools, oil

containers, etc.) have been removed.

2. Lift the hood, grasp the padded area on

the support rod, and secure the support

rod in the clip. Verify that the support

rod is secured in the clip before closing

the hood.

Clip

3. Lower the hood slowly to a height of

about 20 cm (7.9 in) above its closed

position and then let it drop.

CAUTION

When closing the hood, do not push

it excessively such as by applying

your weight. Otherwise, the hood

could be deformed.

6-25

Maintenance and Care

Owner Maintenance

Engine Compartment Overview

Windshield washer fluid reservoir

Brake/Clutch fluid reservoir

Battery

Engine oil-filler cap

Fuse block

Cooling system cap

Engine oil dipstick

Engine coolant reservoir

6-26

Maintenance and Care

Owner Maintenance

Only use SAE 0W-20 oil

Engine Oil

“Certified For Gasoline Engines” by the

American Petroleum Institute (API).

Oil with this trademark symbol conforms

to the current engine and emission system

protection standards and fuel economy

requirements of the International

NOTE

Changing the engine oil should be performed

by an Authorized Mazda Dealer.

Refer to Introduction (page 6-2) for owner's

responsibility in protecting your investment.

Lubricant Standardization and Approval

Committee (ILSAC), comprised of U.S.

and Japanese automobile manufacturers.

qRecommended Oil

U.S.A. and CANADA

Use SAE 0W-20 engine oil.

Mazda Genuine Oil is used in your Mazda

vehicle. Mazda Genuine 0W-20 Oil is

required to achieve optimum fuel

economy.

20

–40

–20

0

10

30 40

–30

–10

–40 –20

80 100

0

20

40 60

For maintenance service, Mazda

recommends Mazda Genuine Parts and

Castrol^®(U.S.A. only).

Except U.S.A. and CANADA

Use SAE 5W-30 engine oil.

Oil container labels provide important

information.

A chief contribution this type of oil makes

to fuel economy is reducing the amount of

fuel necessary to overcome engine

friction.

For maintenance service, Mazda

recommends Mazda Genuine Parts and

Castrol^®(Mexico only).

(ILSAC)

6-27

Maintenance and Care

Owner Maintenance

(ILSAC)

(Mexico)

Use SAE 5W-30 engine oil. If SAE 5W-

30 engine oil is not available, use SAE

5W-20 engine oil.

The quality designation SM, or ILSAC

must be on the label.

–40

–20

0

20

10

30 40

–30

–10

–40 –20

0

20

40 60

80 100

6-28

Maintenance and Care

Owner Maintenance

qVehicle Engine Control Unit Reset Procedure

NOTE

This procedure is intended for vehicles with the engine oil flexible maintenance setting selected.

After replacing the engine oil, have a repair shop such as an Authorized Mazda Dealer

perform the initialization (engine oil data resetting) of the recorded value. If the value

recorded by the computer is not initialized, the wrench indicator light may not turn off or it

may turn on earlier than normal.

NOTE

The initialization (engine oil data resetting) of the recorded value can be performed using the

following procedure:

1. Switch the ignition OFF.

2. Switch the ignition ON with the selector pressed, and press and hold the selector for about 5

seconds until the master warning light

flashes.

Selector

3. After the master warning light

flashes for several seconds, the initialization is completed.

6-29

Maintenance and Care

Owner Maintenance

qInspecting Engine Oil Level

Engine Coolant

qInspecting Coolant Level

WARNING

1. Be sure the vehicle is on a level

surface.

2. Warm up the engine to normal

operating temperature.

Do not use a match or live flame in the

engine compartment. DO NOT ADD

COOLANT WHEN THE ENGINE IS HOT:

A hot engine is dangerous. If the

engine has been running, parts of the

engine compartment can become

very hot. You could be burned.

Carefully inspect the engine coolant

in the coolant reservoir, but do not

open it.

3. Turn it off and wait at least 5 minutes

for the oil to return to the oil pan.

4. Pull out the dipstick, wipe it clean, and

reinsert it fully.

MAX

OK

Switch the ignition to off and

make sure the fan is not running before

attempting to work near the cooling

fan:

MIN

Working near the cooling fan when it

is running is dangerous. The fan

could continue running indefinitely

even if the engine has stopped and

the engine compartment temperature

is high. You could be hit by the fan

and seriously injured.

5. Pull it out again and examine the level.

The level is normal if it is between the

MIN and MAX marks.

If it is near or below MIN, add enough

oil to bring the level to MAX.

CAUTION

Do not overfill the engine oil. This

may cause engine damage.

Do not remove either cooling

system cap when the engine and

radiator are hot:

6. Make sure the O-ring on the dipstick is

positioned properly before reinserting

the dipstick.

When the engine and radiator are

hot, scalding coolant and steam may

shoot out under pressure and cause

serious injury.

7. Reinsert the dipstick fully.

NOTE

Changing the coolant should be done by an

Authorized Mazda Dealer.

6-30

Maintenance and Care

Owner Maintenance

Inspect the antifreeze protection and

coolant level in the coolant reservoir at

least once a year―at the beginning of the

winter season―and before traveling

where temperatures may drop below

freezing.

Ø Use only soft (demineralized)

water in the coolant mixture.

Water that contains minerals will

cut down on the coolant's

effectiveness.

Ø Do not add only water. Always

add a proper coolant mixture.

Ø The engine has aluminum parts

and must be protected by an

ethylene-glycol-based coolant to

prevent corrosion and freezing.

Ø DO NOT USE coolants Containing

Alcohol, methanol, Borate or

Silicate.

Inspect the condition and connections of

all cooling system and heater hoses.

Replace any that are swollen or

deteriorated.

The coolant should be at full in the

radiator and between the F and L marks

on the coolant reservoir when the engine

is cool.

These coolants could damage the

cooling system.

Ø DO NOT MIX alcohol or methanol

with the coolant. This could

damage the cooling system.

Ø Do not use a solution that

contains more than 60%

antifreeze.

This would reduce effectiveness.

Ø If the “FL22” mark is shown on or

near the cooling system cap, use of

FL-22 is recommended when

replacing engine coolant. Using

engine coolant other than FL-22

may cause serious damage to the

engine and cooling system.

If it is at or near L, add enough coolant to

the coolant reservoir to provide freezing

and corrosion protection and to bring the

level to F.

Securely tighten the coolant reservoir tank

cap after adding coolant.

CAUTION

Ø Radiator coolant will damage

paint.

Rinse it off quickly if spilled.

6-31

Maintenance and Care

Owner Maintenance

If the coolant reservoir is empty or new

coolant is required frequently, consult an

Authorized Mazda Dealer.

Brake/Clutch Fluid

Inspecting Brake/Clutch Fluid Level

WARNING

q

If the brake/clutch fluid level is low,

have the brakes inspected:

A low brake/clutch fluid level is

dangerous.

A low level could indicate brake

lining wear or a brake system leak

which could cause the brakes to fail

and lead to an accident.

The brakes and clutch draw fluid from the

same reservoir.

Inspect the fluid level in the reservoir

regularly. It should be kept between the

MAX and MIN lines.

The level normally drops with

accumulated distance, a condition

associated with wear of brake and clutch

linings. If it is excessively low, have the

brake/clutch system inspected by an

Authorized Mazda Dealer.

6-32

Maintenance and Care

Owner Maintenance

Inspect fluid level in the washer fluid

reservoir; add fluid if necessary.

Washer Fluid

qInspecting Washer Fluid Level

WARNING

Use only windshield washer fluid or

plain water in the reservoir:

F

Using radiator antifreeze as washer

fluid is dangerous. If sprayed on the

windshield, it will dirty the

OK

windshield, affect your visibility, and

could result in an accident.

L

Using Washer Fluid Without Anti-freeze

Protection in Cold Weather:

The top of the float should be between F

and L.

Operating your vehicle in

temperatures below 4 degrees C (40

degrees F) using washer fluid without

anti-freeze protection is dangerous

as it could cause impaired windshield

vision and result in an accident. In

cold weather, always use washer

fluid with anti-freeze protection.

Use plain water if washer fluid is

unavailable.

But use only washer fluid in cold weather

to prevent it from freezing.

NOTE

Front and rear washer fluid is supplied from

the same reservoir.

NOTE

State or local regulations may restrict the use

of volatile organic compounds (VOCs), which

are commonly used as anti-freeze agents in

washer fluid. A washer fluid with limited VOC

content should be used only if it provides

adequate freeze resistance for all regions and

climates in which the vehicle will be operated.

6-33

Maintenance and Care

Owner Maintenance

Body Lubrication

Wiper Blades

CAUTION

Ø Hot waxes applied by automatic

car washers have been known to

affect the wiper's ability to clean

windows.

All moving points of the body, such as

door and hood hinges and locks, should

be lubricated each time the engine oil is

changed. Use a nonfreezing lubricant on

locks during cold weather.

Ø To prevent damage to the wiper

blades, do not use gasoline,

kerosene, paint thinner, or other

solvents on or near them.

Make sure the hood's secondary latch

keeps the hood from opening when the

primary latch is released.

Ø When the wiper lever is in the

AUTO position and the ignition is

switched ON, the wipers may

move automatically in the

following cases:

Ø

If the windshield above the rain

sensor is touched.

If the windshield above the rain

sensor is wiped with a cloth.

If the windshield is struck with

a hand or other object.

If the rain sensor is struck with

a hand or other object from

inside the vehicle.

Be careful not to pinch hands or

fingers as it may cause injury, or

damage the wipers. When

washing or servicing your Mazda,

make sure the wiper lever is in the

OFF position.

Contamination of either the windshield or

the blades with foreign matter can reduce

wiper effectiveness. Common sources are

insects, tree sap, and hot wax treatments

used by some commercial car washes.

If the blades are not wiping properly,

clean the window and blades with a good

cleaner or mild detergent; then rinse

thoroughly with clean water. Repeat if

necessary.

6-34

Maintenance and Care

Owner Maintenance

3. Pull down the blade rubber and slide it

out of blade holder.

q

Replacing Windshield Wiper Blades

When the wipers no longer clean well, the

blades are probably worn or cracked.

Replace them.

CAUTION

To prevent damage to the wiper arms

and other components, do not try to

sweep the wiper arm by hand.

NOTE

When raising both windshield wiper arms,

raise the driver's side wiper arm first. When

lowering the wiper arms, slowly lower the

wiper arm from the passenger's side first while

supporting it with your hand. Forcefully

lowering the wiper arms could damage the

wiper arm and blade, and may scratch or

crack the windshield.

4. Remove the metal stiffeners from each

blade rubber and install them in the

new blade.

1. Raise the wiper arm.

2. Open the clip and slide the blade

assembly in the direction of the arrow.

CAUTION

To prevent damage to the windshield

let the wiper arm down easily, do not

let it slap down on the windshield.

6-35

Maintenance and Care

Owner Maintenance

1. Remove the cover and raise the wiper

arm.

CAUTION

Ø Do not bend or discard the

stiffeners. You need to use them

again.

Ø If the metal stiffeners are

switched, the blade's wiping

efficiency could be reduced.

So do not use the driver's side

metal stiffeners on the passenger's

side, or vice versa.

Ø Be sure to reinstall the metal

stiffeners in the new blade rubber

so that the curve is the same as it

was in the old blade rubber.

2. Firmly rotate the wiper blade to the

right until it unlocks, then remove the

blade.

5. Carefully insert the new blade rubber.

Then install the blade assembly in the

reverse order of removal.

CAUTION

To prevent damage to the rear

window, do not let the wiper arm fall

on it.

qReplacing Rear Window Wiper

Blade

When the wiper no longer cleans well, the

blade is probably worn or cracked.

Replace it.

CAUTION

To prevent damage to the wiper arm

and other components, do not move

the wiper by hand.

6-36

Maintenance and Care

Owner Maintenance

3. Pull down the blade rubber and slide it

out of the blade holder.

5. Carefully insert the new blade rubber.

Then install the blade assembly in the

reverse order of removal.

4. Remove the metal stiffeners from the

blade rubber and install them in the

new blade.

CAUTION

Do not bend or discard the stiffeners.

You need to use them again.

6-37

Maintenance and Care

Owner Maintenance

Battery

WARNING

Wash hands after handling the battery and related accessories:

Battery posts, terminals and related accessories contain lead and lead compounds,

chemicals known to the State of California to cause cancer and reproductive harm.

Read the following precautions carefully before using the battery or inspecting

to ensure safe and correct handling:

Always wear eye protection when working near the battery:

Working without eye protection is dangerous. Battery fluid contains SULFURIC ACID

which could cause blindness if splashed into your eyes. Also, hydrogen gas produced

during normal battery operation, could ignite and cause the battery to explode.

Wear eye protection and protective gloves to prevent contact with battery

fluid:

Spilled battery fluid is dangerous.

Battery fluid contains SULFURIC ACID which could cause serious injuries if it gets in

eyes, or on the skin or clothing. If this happens, immediately flush your eyes with

water for 15 minutes or wash your skin thoroughly and get medical attention.

Always keep batteries out of the reach of children:

Allowing children to play near batteries is dangerous. Battery fluid could cause

serious injuries if it gets in the eyes or on the skin.

Keep flames and sparks away from open battery cells and do not allow metal

tools to contact the positive ( ) or negative ( ) terminal of the battery when

working near a battery. Do not allow the positive ( ) terminal to contact the vehicle

body:

Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced

during normal battery operation, could ignite and cause the battery to explode. An

exploding battery can cause serious burns and injuries. Keep all flames including

cigarettes and sparks away from open battery cells.

6-38

Maintenance and Care

Owner Maintenance

Keep all flames, including cigarettes, and sparks away from open battery cells:

Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced

during normal battery operation, could ignite and cause the battery to explode. An

exploding battery can cause serious burns and injuries.

NOTE

Before performing battery maintenance, remove the battery cover.

l

If the vehicle will not be used for an

qBattery Maintenance

extended time, disconnect the battery

cables and charge the battery every six

weeks.

qBattery Replacement

Contact an Authorized Mazda Dealer for a

battery replacement purchase.

To get the best service from a battery:

l

Keep it securely mounted.

Keep the top clean and dry.

Keep terminals and connections clean,

l

tight, and coated with petroleum jelly

or terminal grease.

Rinse off spilled electrolyte

l

immediately with a solution of water

and baking soda.

6-39

Maintenance and Care

Owner Maintenance

l

The system does not operate and the

operation indicator light on the

transmitter does not flash when the

buttons are pressed.

The system's operational range is

reduced.

Key Battery Replacement

If the buttons on the transmitter are

inoperable and the operation indicator

light does not flash, the battery may be

dead.

Replacing the battery at an Authorized

Mazda Dealer is recommended to prevent

damage to the key. If replacing the battery

by yourself, follow the instruction below.

Replace with a new battery before the

transmitter becomes unusable.

CAUTION

Replacing the key battery

Ø Make sure the battery is installed

correctly. Battery leakage could

occur if it is not installed correctly.

Ø When replacing the battery, be

careful not to touch any of the

internal circuitry and electrical

terminals, bend the electrical

terminals, or get dirt in the

transmitter as the transmitter

could be damaged.

1. Press the knob and pull out the

auxiliary key.

Knob

Ø There is the danger of explosion if

the battery is not correctly

replaced.

Ø Dispose of used batteries

according to the following

instructions.

Ø

2. Twist a tape-wrapped flathead

screwdriver in the direction of the

arrow and open the cover slightly.

Insulate the plus and minus

terminals of the battery using

cellophane or equivalent tape.

Never disassemble.

Ø

Cover

Never throw the battery into

fire or water.

Ø

Never deform or crush.

Ø Replace only with the same type

battery (CR2025 or equivalent).

The following conditions indicate that the

battery power is low:

l

The KEY indicator light (green) flashes

in the instrument cluster for about 30

seconds after the engine is turned off

(for vehicles with a type A meter,

messages are displayed in the

instrument cluster).

6-40

Maintenance and Care

Owner Maintenance

3. Insert the tape-wrapped flathead

screwdriver into the gap and slide it in

the direction of the arrow.

5. Remove the battery cap, then remove

the battery.

Cover

Gap

6. Insert a new battery with the positive

pole facing up, and then cover the

battery with the battery cap.

4. Twist the flathead screwdriver in the

direction of the arrow and remove the

cover.

Cover

7. Close the cover.

8. Reinsert the auxiliary key.

6-41

Maintenance and Care

Owner Maintenance

Tires

CAUTION

Ø Be careful not to allow the rubber

ring shown in the figure to be

scratched or damaged.

Ø If the rubber ring detaches,

reattach it before inserting a new

battery.

For reasons of proper performance, safety,

and better fuel economy, always maintain

recommended tire inflation pressures and

stay within the recommended load limits

and weight distribution.

WARNING

Using Different Tire Types:

Driving your vehicle with different

types of tires is dangerous. It could

cause poor handling and poor

braking; leading to loss of control.

Except for the limited use of the

temporary spare tire, use only the

same type tires (radial, bias-belted,

bias-type) on all four wheels.

Rubber ring

Using Wrong-Sized Tires:

Using any other tire size than what is

specified for your Mazda (page 9-8)

is dangerous. It could seriously affect

ride, handling, ground clearance, tire

clearance, and speedometer

calibration. This could cause you to

have an accident. Use only tires that

are the correct size specified for your

Mazda.

6-42

Maintenance and Care

Owner Maintenance

NOTE

l

qTire Inflation Pressure

Always check tire pressure when tires are

cold.

WARNING

Always inflate the tires to the correct

pressure:

l

Warm tires normally exceed recommended

pressures. Do not release air from warm

tires to adjust the pressure.

Underinflation can cause reduced fuel

economy, uneven and accelerated tire wear,

and poor sealing of the tire bead, which

will deform the wheel and cause separation

of tire from rim.

Overinflation or underinflation of

tires is dangerous. Adverse handling

or unexpected tire failure could result

in a serious accident.

Refer to Tires on page 9-8.

l

Use only a Mazda-genuine tire valve

cap:

Overinflation can produce a harsh ride,

uneven and accelerated tire wear, and a

greater possibility of damage from road

hazards.

Keep your tire pressure at the correct

levels. If one frequently needs inflating,

have it inspected.

Use of a non-genuine part is

dangerous as the correct tire air

pressure cannot be maintained if the

tire valve becomes damaged. If the

vehicle is driven under this condition,

the tire air pressure will decrease

which could result in a serious

accident. Do not use any part for the

tire valve cap that is not a Mazda-

genuine part.

qTire Rotation

WARNING

Rotate tires periodically:

Irregular tire wear is dangerous. To

equalize tread wear for maintaining

good performance in handling and

braking, rotate the tires according to

the scheduled maintenance charts.

Refer to Scheduled Maintenance on

page 6-4.

Inspect all tire pressures monthly

(including the spare) when the tires are

cold. Maintain recommended pressures

for the best ride, handling, and minimum

tire wear.

Refer to the specification charts (page

9-8).

After adjusting the tire pressure,

initialization of the tire pressure

monitoring system is necessary to make

the system operate normally.

Refer to Tire Pressure Monitoring System

Initialization on page 4-151.

6-43

Maintenance and Care

Owner Maintenance

During rotation, inspect them for correct

balance.

qReplacing a Tire

WARNING

Always use tires that are in good

condition:

Driving with worn tires is dangerous.

Reduced braking, steering, and

traction could result in an accident.

Replace all four tires at the same time:

Replacing just one tire is dangerous.

It could cause poor handling and

poor braking resulting in loss of

vehicle control. Mazda strongly

recommends that you replace all four

tires at the same time.

Forward

Do not include (TEMPORARY USE ONLY)

spare tire in rotation.

Also, inspect them for uneven wear and

damage. Abnormal wear is usually caused

by one or a combination of the following:

If a tire wears evenly, a wear indicator

will appear as a solid band across the

tread.

l

Incorrect tire pressure

Improper wheel alignment

Out-of-balance wheel

Severe braking

l

Replace the tire when this happens.

l

Tread wear indicator

After rotation, inflate all tire pressures to

specification (page 9-8) and inspect the

lug nuts for tightness.

After adjusting the tire pressure,

initialization of the tire pressure

monitoring system is necessary to make

the system operates normally.

Refer to Tire Pressure Monitoring System

Initialization on page 4-151.

New tread

Worn tread

You should replace the tire before the

band crosses the entire tread.

After adjusting the tire pressure,

initialization of the tire pressure

monitoring system is necessary to make

the system operates normally.

CAUTION

Rotate unidirectional tires and radial

tires that have an asymmetrical tread

pattern or studs only from front to

rear, not from side to side. Tire

performance will be reduced if

rotated from side to side.

Refer to Tire Pressure Monitoring System

Initialization on page 4-151.

6-44

Maintenance and Care

Owner Maintenance

NOTE

CAUTION

Tires degrade over time, even when they are

not being used on the road. It is recommended

that tires generally be replaced when they are

6 years or older. Heat caused by hot climates

or frequent high loading conditions can

accelerate the aging process. You should

replace the spare tire when you replace the

other road tires due to the aging of the spare

tire. The period in which the tire was

manufactured (both week and year) is

indicated by a 4-digit number.

Ø Do not use your temporary spare

tire rim with a snow tire or a

conventional tire. Neither will

properly fit and could damage

both tire and rim.

Ø The temporary spare tire has a

tread life of less than 5,000 km

(3,000 miles). The tread life may

be shorter depending on driving

conditions.

Ø The temporary spare tire is for

limited use, however, if the tread

wear solid-band indicator

appears, replace the tire with the

same type of temporary spare

(page 6-45).

Refer to Tire Labeling on page 8-25.

qTemporary Spare Tire

Inspect the temporary spare tire at least

monthly to make sure it is properly

inflated and stored.

NOTE

Tires degrade over time, even when they are

not being used on the road. It is recommended

that tires generally be replaced when they are

6 years or older. Heat caused by hot climates

or frequent high loading conditions can

accelerate the aging process. You should

replace the spare tire when you replace the

other road tires due to the aging of the spare

tire. The period in which the tire was

The temporary spare tire condition gradually

deteriorates even if it has not been used.

The temporary spare tire is easier to

handle because of its construction which

is lighter and smaller than a conventional

tire. This tire should be used only for an

emergency and only for a short distance.

manufactured (both week and year) is

indicated by a 4-digit number.

Refer to Tire Labeling on page 8-25.

Use the temporary spare tire only until the

conventional tire is repaired, which should

be as soon as possible.

qReplacing a Wheel

Refer to Tires on page 9-8.

WARNING

Always use wheels of the correct size

on your vehicle:

Using a wrong-sized wheel is

dangerous. Braking and handling

could be affected, leading to loss of

control and an accident.

6-45

Maintenance and Care

Owner Maintenance

CAUTION

A wrong-sized wheel may adversely

affect:

Ø Tire fit

Ø Wheel and bearing life

Ø Ground clearance

Ø Snow-chain clearance

Ø Speedometer calibration

Ø Headlight aim

Ø Bumper height

Ø Tire Pressure Monitoring System

NOTE

l

When replacing a wheel, make sure the new

one is the same as the original factory

wheel in diameter, rim width, and offset

(inset/outset).

l

For details, contact an Authorized Mazda

Dealer.

Proper tire balancing provides the best

riding comfort and helps reduce tread

wear. Out-of-balance tires can cause

vibration and uneven wear, such as

cupping and flat spots.

6-46

MEMO

6-47

Maintenance and Care

Owner Maintenance

Light Bulbs

With LED headlights

Luggage compartment light

Rear map lights

Overhead light (Front)/

Map lights

High-mount brake light

Vanity mirror lights

Side turn

signal lights

Front turn signal lights/

Rear side-marker lights

Front side-marker lights

Taillights

Headlights (Low beam)

Daytime running lights/

Parking lights

Headlights (High beam)

Fog lights

Brake lights/Taillights

Rear turn signal lights

Taillights (Liftgate side)

Reverse lights

License plate lights

With halogen headlights

Luggage compartment light

Rear map lights

Overhead light (Front)/

Map lights

High-mount brake light

Vanity mirror lights

Side turn

signal lights

Front turn signal lights/

Parking lights (Front side-

marker lights)

Rear side-marker lights

Rear turn signal lights

Brake lights/Taillights

Taillights (Liftgate side)

Reverse lights

Headlights (Low beam)

Fog lights

License plate lights

Headlights (High beam)/

Daytime running lights

Some models.

6-48

Maintenance and Care

Owner Maintenance

qReplacing Exterior Light Bulbs

WARNING

Headlights (With LED headlights)

Never touch the glass portion of a

halogen bulb with your bare hands and

always wear eye protection when

handling or working around the bulbs:

When a halogen bulb breaks, it is

dangerous. These bulbs contain

pressurized gas. If one is broken, it

will explode and serious injuries

could be caused by the flying glass.

If the glass portion is touched with

bare hands, body oil could cause the

bulb to overheat and explode when

lit.

Low-beam bulbs, High-beam bulbs,

Daytime running lights/Parking lights

The LED bulb cannot be replaced as a

single unit because it is an integrated unit.

The LED bulb has to be replaced with the

unit. We recommend an Authorized

Mazda Dealer when the replacement is

necessary.

Headlights (With halogen headlights)

Low-beam bulbs, High-beam bulbs/

Daytime running lights

Always keep halogen bulbs out of the

reach of children:

1. Make sure the ignition is switched off,

and the headlight switch is off.

Playing with a halogen bulb is

dangerous. Serious injuries could be

caused by dropping a halogen bulb

or breaking it some other way.

2. Lift the hood.

3. (Right side)

Remove the windshield washer fluid

reservoir from the guide.

CAUTION

When removing the lens or lamp unit

using a flathead screwdriver, make

sure that the flathead screwdriver

does not contact the interior

terminal. If the flathead screwdriver

contacts the terminal, a short circuit

may occur.

Windshield washer

fluid reservoir

Guide

NOTE

l

To replace the bulb, contact an Authorized

Mazda Dealer.

l

If the halogen bulb is accidentally touched,

4. Disconnect the connector from the unit

by pressing the tab on the connector

with your finger and pulling the

connector downward.

it should be cleaned with rubbing alcohol

before being used.

Use the protective cover and carton for the

replacement bulb to dispose of the old bulb

promptly and out of the reach of children.

l

6-49

Maintenance and Care

Owner Maintenance

Low-beam bulbs

High-beam bulbs/Daytime running

lights

High-beam bulbs/Daytime running

lights

5. Turn the socket and bulb assembly to

remove it. Carefully remove the bulb

from its socket in the reflector by

gently pulling it straight backward out

of the socket.

6. Install the new bulb in the reverse order

of the removal procedure.

Front turn signal lights/Front side-

marker lights (With LED headlights)

Front turn signal lights/Parking lights

(Front side-marker lights) (With

halogen headlights)

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. If you are changing the right bulb, start

the engine, turn the steering wheel all

the way to the right, and turn off

engine. If you are changing the left

bulb, turn the steering wheel to the left.

6-50

Maintenance and Care

Owner Maintenance

3. Pull the center of each plastic retainer

and remove the retainers.

Front turn signal lights/Front side-

marker lights (With LED headlights)

Removal

Installation

4. Turn the screw counterclockwise and

remove it, and then partially peel back

the mudguard.

Front turn signal lights/Parking lights

(Front side-marker lights) (With

halogen headlights)

5. Turn the socket and bulb assembly

counterclockwise and remove it.

7. Install the new bulb in the reverse order

of the removal procedure.

6. Disconnect the bulb from the socket.

Fog lights (With LED headlights)

The LED bulb cannot be replaced as a

single unit because it is an integrated unit.

The LED bulb has to be replaced with the

unit. We recommend an Authorized

Mazda Dealer when the replacement is

necessary.

Fog lights (With halogen headlights)^í

1. Make sure the ignition is switched off,

and the headlight switch is off.

^íSome models.

6-51

Maintenance and Care

Owner Maintenance

2. If you are changing the right bulb, start

the engine, turn the steering wheel all

the way to the right, and turn off

5. Disconnect the connector from the unit

by pressing the tab on the connector

with your finger and pulling the

connector downward.

engine. If you are changing the left

bulb, turn the steering wheel to the left.

3. Pull the center of each plastic retainer

and remove the retainers.

Removal

Installation

6. Turn the socket and bulb assembly to

remove it. Carefully remove the bulb

from its socket in the reflector by

gently pulling it straight back out of the

socket.

4. Turn the screw counterclockwise and

remove it, and then partially peel back

the mudguard.

7. Install the new bulb in the reverse order

of the removal procedure.

Side-turn signal lights

The LED bulb cannot be replaced as a

single unit because it is an integrated unit.

The LED bulb has to be replaced with the

unit. We recommend an Authorized

Mazda Dealer when the replacement is

necessary.

6-52

Maintenance and Care

Owner Maintenance

Brake lights/Taillights, Rear side-

marker lights, Taillights, Rear turn

signal lights, Reverse lights (With LED

headlights)

Reverse lights

Brake lights/Taillights, Rear side-

marker lights, Taillights

The LED bulb cannot be replaced as a

single unit because it is an integrated unit.

The LED bulb has to be replaced with the

unit. We recommend an Authorized

Mazda Dealer when the replacement is

necessary.

Rear turn signal lights, Reverse lights

3. Turn the socket and bulb assembly

counterclockwise and remove it.

1. Make sure the ignition is switched off,

and the headlight switch is off.

4. Disconnect the bulb from the socket.

2. Remove the cover with a cloth-

wrapped flathead screwdriver to the

cover.

Rear turn signal lights

Reverse lights

6-53

Maintenance and Care

Owner Maintenance

5. Install the new bulb in the reverse order

of the removal procedure.

4. Disconnect the bulb from the socket.

Brake lights/Taillights

Brake lights/Taillights, Rear turn signal

lights, Rear side-marker lights,

Taillights (Liftgate side), Reverse lights

(With halogen headlights)

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. Remove the cover with a cloth-

wrapped flathead screwdriver to the

cover.

Brake lights/Taillights, Rear turn signal

lights, Rear side-marker lights

Rear turn signal lights

Taillights (Liftgate side), Reverse lights

Rear side-marker lights

3. Turn the socket and bulb assembly

counterclockwise and remove it.

6-54

Maintenance and Care

Owner Maintenance

Taillights (Liftgate side)

2. Wrap a flathead screwdriver with a soft

cloth to prevent damage to the lens,

and then remove the lens by carefully

prying on the edge of the lens with a

flathead screwdriver.

3. Disconnect the bulb by pulling it out.

Reverse lights

4. Install the new bulb in the reverse order

of the removal procedure.

qReplacing Interior Light Bulbs

Overhead light (Front)/Map lights,

Rear map lights, Vanity mirror lights^í

1. Wrap a small flathead screwdriver with

a soft cloth to prevent damage to the

lens, and then remove the lens by

carefully prying on the edge of the lens

with the flathead screwdriver.

5. Install the new bulb in the reverse order

of the removal procedure.

High-mount brake light

The LED bulb cannot be replaced as a

single unit because it is an integrated unit.

The LED bulb has to be replaced with the

unit. We recommend an Authorized

Mazda Dealer when the replacement is

necessary.

2. Disconnect the bulb by pulling it out.

License plate lights

1. Make sure the ignition is switched off,

and the headlight switch is off.

^íSome models.

6-55

Maintenance and Care

Owner Maintenance

Overhead light (Front)/Map lights

Vanity mirror lights

Rear map lights

3. Install the new bulb in the reverse order

of the removal procedure.

6-56

Maintenance and Care

Owner Maintenance

Luggage compartment light

3. Insert the flathead screwdriver into the

gap between the lens and the lens unit,

and then slide the screwdriver to detach

the lens.

1. Wrap a small flathead screwdriver with

a soft cloth to prevent damage to the

lens and remove the lens unit by

carefully prying on the edge of the lens

unit with the flathead screwdriver.

4. Disconnect the bulb by pulling it out.

2. Disconnect the electrical connector

from the bulb by pressing the tab on

the connector with your finger and

pulling the connector.

5. Install the new bulb in the reverse order

of the removal procedure.

CAUTION

When replacing the bulb always

disconnect the connector first.

Otherwise, electric and electronic

devices could be shorted.

6-57

Maintenance and Care

Owner Maintenance

3. Pull the fuse straight out with the fuse

puller provided on the fuse block

located in the engine compartment.

Fuses

Your vehicle's electrical system is

protected by fuses.

If any lights, accessories, or controls do

not work, inspect the appropriate circuit

protector. If a fuse has blown, the inside

element will be melted.

If the same fuse blows again, avoid using

that system and consult an Authorized

Mazda Dealer as soon as possible.

qFuse Replacement

4. Inspect the fuse and replace it if it is

blown.

Replacing the fuses on the vehicle's left

side

If the electrical system does not work,

first inspect the fuses on the vehicle's left

side.

1. Make sure the ignition is switched off,

and other switches are off.

2. Open the fuse panel cover.

Blown

Normal

5. Insert a new fuse of the same amperage

rating, and make sure it fits tightly. If it

does not fit tightly, have an expert

install it. We recommend an

Authorized Mazda Dealer.

If you have no spare fuses, borrow one

of the same rating from a circuit not

essential to vehicle operation, such as

the AUDIO or OUTLET circuit.

6-58

Maintenance and Care

Owner Maintenance

3. If any fuse but the MAIN fuse is

blown, replace it with a new one of the

same amperage rating.

CAUTION

Always replace a fuse with a genuine

Mazda fuse or equivalent of the same

rating. Otherwise you may damage

the electric system.

6. Reinstall the cover and make sure that

it is securely installed.

Replacing the fuses under the hood

If the headlights or other electrical

components do not work and the fuses in

the cabin are normal, inspect the fuse

block under the hood. If a fuse is blown, it

must be replaced. Follow these steps:

Normal

Blown

WARNING

1. Make sure the ignition is switched off,

and other switches are off.

Do not replace the main fuse by

yourself. Have an Authorized Mazda

Dealer perform the replacement:

Replacing the fuse by yourself is

dangerous because the MAIN fuse is

a high current fuse. Incorrect

replacement could cause an electrical

shock or a short circuit resulting in a

fire.

2. Remove the fuse block cover.

4. Reinstall the cover and make sure that

it is securely installed.

6-59

Maintenance and Care

Owner Maintenance

qFuse Panel Description

Fuse block (Engine compartment)

FUSE

DESCRIPTION

PROTECTED COMPONENT

RATING

1

2

3

4

5

6

7

ADD FAN GE

IG2

30 A

40 A

30 A

―

Cooling fan

For protection of various circuits

Engine control system

INJECTOR

FAN DE

―

P.WINDOW1

―

Power windows

―

ADD FAN DE

40 A

EVVT

SCR1

8

20 A

Engine control system

Rear window defogger

9

DEFOG

DCDC DE

FAN GE

40 A

30 A

20 A

40 A

20 A

40 A

50 A

10

11

12

13

14

15

16

―

Cooling fan

EPB L

Electric parking brake (LH)

Audio system

AUDIO

EPB R

Electric parking brake (RH)

Engine control system

ENG.MAIN

ABS/DSC M

ABS, Dynamic stability control system

6-60

Maintenance and Care

Owner Maintenance

FUSE

RATING

DESCRIPTION

PROTECTED COMPONENT

For protection of various circuits

17

50 A

18

19

20

21

22

WIPER

HEATER

20 A

40 A

30 A

7.5 A

15 A

Front window wiper and washer

Air conditioner

DCDC REG

ENGINE.IG1

C/U IG1

―

Engine control system

For protection of various circuits

H/L LOW L

HID L

23

15 A

Headlight low beam (LH)

24

25

26

27

28

29

30

31

32

33

34

H/L LOW R

ENGINE3

ENGINE2

ENGINE1

AT

15 A

20 A

7.5 A

15 A

10 A

15 A

20 A

Headlight low beam (RH)

Engine control system

Transaxle control system^í, Ignition switch

―

H/CLEAN

A/C

Air conditioner

Transaxle control system^í

AT PUMP

STOP

Brake lights

R.WIPER

H/L HI

Rear window wiper

Headlight high beam

HID R

ST.HEATER

35

15 A

―

36

37

FOG

15 A

Fog lights^í

7.5 A

Engine control system

38

39

40

41

42

43

44

45

46

47

48

AUDIO2

GLOW SIG

METER2

METER1

SRS1

7.5 A

5 A

Audio system

―

7.5 A

10 A

7.5 A

25 A

15 A

30 A

15 A

25 A

15 A

―

Instrument cluster

Air bag

BOSE

Bose^®Sound System-equipped model^í

AUDIO1

ABS/DSC S

FUEL PUMP

FUEL WARM

TAIL

Audio system

ABS, Dynamic stability control system

Fuel system

―

Taillights, License plate lights

FUEL PUMP2

SCR2

49

50

25 A

―

Hazard warning flashers, Turn signal lights, Parking lights

(Front side-marker lights)

HAZARD

51

52

53

DRL

R.OUTLET2

HORN

15 A

Daytime running lights^í

Accessory sockets

Horn

^íSome models.

6-61

Maintenance and Care

Owner Maintenance

FUSE

RATING

DESCRIPTION

PROTECTED COMPONENT

54

ROOM

15 A

Overhead light

Fuse block (Left side)

FUSE

RATING

DESCRIPTION

PROTECTED COMPONENT

1

2

P.SEAT D

P.WINDOW3

R.OUTLET3

P.WINDOW2

SRS2/ESCL

D.LOCK

SEAT WARM

SUNROOF

F.OUTLET

MIRROR

R.OUTLET1

―

30 A

15 A

25 A

15 A

25 A

20 A

10 A

15 A

7.5 A

15 A

―

Power seat^í

―

3

Accessory sockets

Power windows

4

5

―

6

Power door locks

Seat warmer^í

7

8

Moonroof^í

9

Accessory sockets

Power control mirror

10

11

12

13

14

15

―

6-62

^íSome models.

Maintenance and Care

Owner Maintenance

FUSE

RATING

DESCRIPTION

PROTECTED COMPONENT

16

17

18

19

20

21

―

M.DEF

―

7.5 A

―

Mirror defogger^í

―

AT IND

P.SEAT P

7.5 A

30 A

AT shift indicator^í

Power seat^í

^íSome models.

6-63

Owner Maintenance for Your Mazda Cx-5 SUV First Generation (2013-2016)

Related Topics

Popular Owner Manuals

Latest Owner Manuals