Get MBUX multimedia system -> Navigation and traffic Guide for Mercedes GLE SUV Fourth Generation (2020-2026)

Navigation and trac

Switching navigation on

Multimedia system:

Navigation

Alternatively, switch on the MBUX voice assis-

tant (/ page 475).

Switch to navigation.

The map appears.

Navigation overview

Digital map

Navigation module (reduced view)

Route guidance active:

The navigation module shows the information

relevant to the route in the zoomed-out view,

e.g. the destination or a trac delay

£ Ends the current route guidance

Tapping opens the navigation module and dis-

plays the route overview (/ page 544)

Sets map orientation Ä and map type

Calls up the telephone menu

Current vehicle position (vehicle symbol or

arrow)

Calls up entertainment applications

Elevation and map scale (/ page 561)

Navigation window shows the next manoeuvre

(zoomed out view) or the route monitor

(zoomed in view)

Route guidance active: route monitor shows,

e.g. route sections, upcoming driving

manoeuvres with lane recommendations, des-

tination, trac delays, 3D images at motor-

way exits, online content

Pressing

2 several times changes the map orien-

tation in this order:

2D and to the north

2D and in the direction of travel

3D and in the direction of travel

530

MBUX multimedia system

F167 0057 02

Map with complete route

If the map is moved, the map switches

between 3D direction of travel and 2D north

orientation.

The following map types

2 are available:

Daytime display

Night-time display

Satellite map

If you notice a problem with the digital map

you can report this under

Destination entry

▌Notes on destination entry

WARNING Risk of distraction from operat-

ing integrated communication equipment

while the vehicle is in motion

If you operate communication equipment inte-

grated in the vehicle when driving, you could

be distracted from the trac situation. This

could also cause you to lose control of the

vehicle.

Only operate this equipment when the

trac situation permits.

If you cannot be sure of this, stop the

vehicle whilst paying attention to road

and trac conditions and operate the

equipment with the vehicle stationary.

You must observe the legal requirements for the

country in which you are currently driving when

operating the multimedia system.

▌Entering a POI or address

Requirements:

For the online search:

There is an Internet connection.

Mercedes me connect is available.

You have set up a user account in the

Mercedes me Portal.

The vehicle is connected with the user

account and you have accepted the terms

of use.

Further information can be found at:

The service is available and has been acti-

vated.

If Online Search is not available, the search is

performed using the data of the digital map.

MBUX multimedia system

531

F167 0057 02

Multimedia system:

Navigation

Example: entering a POI or address

Input line with current entry

Deletes an entry

Selects previous destinations

Displays and selects additional destination

searches

Adopts the search result in the input line and

continues the search

Search result

Deletes the last character entered

Hides the keypad

Switches to handwriting recognition

(/ page 505)

Sets the written language

Switches to digits and special characters

Switches to upper-case or lower-case letters

If available, selecting the p symbol starts the

MBUX Voice Assistant.

Enter a destination. The entries can be made

in any order.

The search results are displayed in a list.

Online search results for POIs may contain

additional information, for example opening

times and ratings. The information is provided

by an online map service.

This online function is not available in all

countries.

The following entries can be made, for example in

Town, street, house number or street, town

Postcode

POI name or POI category, e.g.

Restaurants

Town, POI name

Contact name

Geo-coordinates (/ page 535)

Three-word addresses from what3words

(/ page 535)

Entering three-word addresses is possible in

the online search.

Hide the keyboard with a.

Select the destination in the list.

The following menu shows the selected desti-

nation with the address information and a cor-

responding map section.

The menu enables the route to be calculated.

532

MBUX multimedia system

F167 0057 02

▌Selecting a destination suggestion

Requirements:

The

Allow destination suggestions option is

switched on (/ page 512).

The multimedia system has gathered sucient

data in order to show destination suggestions.

Multimedia system:

Navigation

Select Suggestions.

The route is calculated in the following menu.

If Suggestions has been selected, a menu is

available via Ä. The menu oers settings

for the suggestions and memory functions.

Managing destination suggestions

(/ page 554).

▌Selecting previous destinations

Multimedia system:

Navigation

Select Previous destinations.

Select the destination.

The following menu enables the route to be

calculated.

You can save a destination as a favourite

(/ page 553).

▌Selecting a POI

Requirements:

For use of personal POIs: a USB device is con-

nected with the multimedia system.

Personal POIs with the GPS Exchange format

(.gpx) have been saved in the PersonalPOI

folder on the USB device.

Multimedia system:

Navigation

Select POIs.

Select one of the displayed quick-access cate-

gories, e.g. j .

Select the POI.

The following menu enables the route to be

calculated.

Select All categories or Personal POIs (see

requirements).

Select the category.

Select the POI.

The following menu enables the route to be

calculated.

Setting a search lter aer selecting a POI cate-

gory

The preset search position depends on the status

of the route guidance:

If route guidance is not active,

In the vicinity

is searched.

If route guidance is active,

Along the route is

searched.

When the search results are displayed, select

Filter.

Select the search position, e.g. In the vicinity.

If a route with intermediate destinations

already exists and Near destination has been

selected in the search lters, the destination

is selected for the search.

MBUX multimedia system

533

F167 0057 02

Select the desired travelling time to the point

of interest.

Select Search results.

Conguring categories for quick access

The categories are displayed:

As symbols aer calling up the destination

entry via ª

As a list aer calling up

All categories

In the POI menu, select All categories.

Select f or ß for a category.

Tapping on f adds the category.

Tapping on ß removes the category.

Use G to change back.

The new categories are shown aer the desti-

nation entry is called up the next time.

If all available quick-access positions are full,

select the category to be replaced.

Changing the order of quick-access categories

In the POI menu, press and hold a category for

quick access.

Tap on the arrows next to the selected cate-

gory.

The arrows for the other categories are greyed

out.

Drag the category up or down.

Select ø.

Deleting quick-access categories

In the POI menu, press and hold a category for

quick access.

Select ß for the chosen category.

Select Delete.

Select ø.

Changing categories for personal POIs

Select Personal POIs.

Press on a category as long as is necessary

until a menu appears.

Select Change name and enter a name.

Select Change icon and select a symbol.

Select Delete and conrm the prompt with

Yes.

▌Selecting a contact for destination entry

Requirements:

A mobile phone is connected to the multime-

dia system (/ page 574).

The contacts from the mobile phone have

been downloaded .

The contact has a navigable address.

The address data can be located on the digital

map.

Multimedia system:

Navigation

Enter a contact in the entry line.

Select the address.

The following menu enables the route to be

calculated.

Alternatively, aer calling up the destination

entry, you can enter the name of a contact in

the search eld.

534

MBUX multimedia system

F167 0057 02

▌Entering geo-coordinates

Multimedia system:

Navigation

Enter the geo-coordinates as latitude and lon-

gitude.

Examples of input formats:

47°58'11"N 7°57'25"E (degrees, minutes and

seconds)

47.969722 7.956944 (decimal degrees)

Conrm the entry.

The following menu enables the route to be

calculated.

▌Entering the destination as a three-word

address

Requirements:

An active Internet connection is indicated in

the status line on the media display with the

Q symbol.

The online search is active.

Multimedia system:

Navigation

Enter the destination as a three-word address

from what3words. The entry can be made with

spaces between the words instead of dots.

The search results are displayed.

Select the destination in the list.

The following menu enables the route to be

calculated.

The Brandenburg Gate has this language depend-

ent three-word address:

German: tapfer.gebäude.verliehen

English:

French: post.ombrant

Searching for a destination using three-word

addresses is not possible in all countries and

in all languages.

Alternatively, use the following entry options:

Entry in the global search (/ page 504)

Voice navigation (/ page 475)

Example: during a telephone call you are given

a 3-word address. Aer activating the MBUX

voice assistant, say one of the following two

voice commands:

Navigate to tapfer gebäude verliehen

Navigate to tapfer Punkt gebäude Punkt

verliehen

Three-word addresses from what3words are an

alternative addressing system for multilingual

georeferencing of global locations with a resolu-

tion of three metres. Using this grid, locations on

the Earth's surface are included which do not

have a building address such as a street and

house number, for example.

MBUX multimedia system

535

F167 0057 02

Three-word addresses are unique, easy to

remember and suce for most routine appli-

cations.

You can convert addresses to three-word

addresses and back again:

At the website

In the what3words apps

▌Selecting a destination on the map

Multimedia system:

Navigation

If necessary, move the map (/ page 560).

Press and hold on the map.

Available destinations are displayed.

Briey press on a POI symbol.

The POI is selected. If there are several POIs

at this map position, a list appears.

Select the destination in the Selected objects

list.

The following menu enables the route to be

calculated.

▌Selecting a destination from favourites

Requirements:

Destinations are saved as favourites.

Save a previous destination or a destination

suggestion as a favourite (/ page 553).

Multimedia system:

Navigation

Select Favourites.

Select a favourite.

The route is calculated in the following menu.

Addresses for home and work are already set

Select Home or Work.

The following menu enables the route to be

calculated.

Addresses for home and work are not yet set

Select Home or Work.

The prompt

No "Home" address available.

Set address now?

appears, for example.

Select Yes.

Search for or select the address.

Select Save.

Deleting favourites

Select Ä for a favourite.

Select Delete.

Select Delete all.

Conrm the prompt.

When all the favourites have been deleted,

Add favourite is available, for example.

▌Selecting received destinations

Requirements:

There is an Internet connection for receiving

external destinations.

A destination has been sent to the vehicle.

Destinations have been shared from another

seat in the vehicle.

536

MBUX multimedia system

F167 0057 02

Multimedia system:

Navigation

The vehicle can receive destinations from services

or apps. You will be informed when a destination

is received.

Select Received destinations.

Select a destination.

The route is calculated in the following menu.

You can save a received destination in the

favourites (/ page 553).

Deleting received destinations

Delete a destination with E.

Select Delete all.

Route

▌Calculating a route

Example: detailed display

Calls up alternative routes

Calculates the route and starts route guid-

ance

Selects a point of interest in the vicinity of the

destination

Destination address

The detailed display can contain additional

entries, such as a three-word address from

what3words, online content

If the destination is located in a multi-storey

car park, for example, and corresponding data

is available, the parking levels are displayed.

Aer selection of a destination the route is be cal-

culated.

Select one of the options.

Calling up alternative routes

Select Routes.

Select an alternative route (/ page 545).

Starting route guidance

Select ¥ Let's go!.

Calling up the detailed display with destination

address

Pull the bar above 2 upwards.

Depending on the destination selection and

availability, online content, for example ratings

and weather information, is shown.

If the destination is in a dierent time zone, a

message is displayed.

MBUX multimedia system

537

F167 0057 02

To share a destination: select Ç Share.

This option allows you to scan the displayed

QR code.

To save a destination as a favourite: select

ß Favourite and then an option.

To call up an Internet address: if a web

address is available, select www.

To call the destination: if a telephone number

is available, select Call.

Searching for POIs in the vicinity of the destina-

tion shown

Select In the vicinity.

Search using categories, enter a search entry

or search for a personal POI (/ page 533).

Adding an intermediate destination to the existing

route or starting a new route guidance

Select ¦ Add.

The selected destination address is set as the

next intermediate destination. Route guidance

begins.

There are already four intermediate destina-

tions: conrm the prompt with Yes and select

an intermediate destinations in the route over-

view (/ page 544), that should be overwrit-

ten with the new intermediate destination.

Select Í Replace.

The selected destination address is set as a

new destination. Route guidance begins.

If you call up the menu during route guidance,

more options are available:

To change the order of destinations, select

Move (/ page 544).

To delete the destination, select

Delete

(/ page 544).

To cancel route guidance, select

Cancel

route guidance

▌Paying for the charging process on a route with

Mercedes me Charge (plug-in hybrid)

Requirements:

The Mercedes me Charge service is available

and subscribed to in the Mercedes me Portal.

The services "Navigation with Electric Intelli-

gence", "Display of charging stations" and

"Mercedes me Charge" are activated.

To select a charging station: the Schedule

charging stops

option is switched on in the

multimedia system.

For authentication at the charging station:

aer activation in the Mercedes me Portal,

you have concluded a charging contract with

your payment details with the respective con-

tractual partners.

For authentication using the app: the

Mercedes me App is installed on the external

device, e.g. tablet or smartphone.

For charging stations without remote access,

you have purchased an RFID card for the con-

tracting partner.

This function is not available in all countries.

538

MBUX multimedia system

F167 0057 02

Multimedia system:

Navigation

Observe the following information:

Read the notes on charging the high-volt-

age battery (/ page 322).

Read the notes on charging the high-volt-

age battery at the charging station

(/ page 327) and (/ page 328).

Before selection of a charging station: the

data for the charging stations is based on

the online content available from the

respective third-party provider.

Observe the local information and condi-

tions.

With the Plug & Charge charging function of

Mercedes me Charge, you can charge the

vehicle at public Plug & Charge-enabled

charging stations. The charging process starts

immediately when the charging cable is plug-

ged into the charging station. No further

authentication is required. Communication

between the vehicle and the charging station

takes place directly via the charging cable.

This charging function is not available in all

countries.

To select a charging station: tap on a symbol

on the map for a charging station or on a

group of symbols for several charging stations.

If a group of symbols is selected, select the

charging station from the list.

The following information is displayed (if availa-

ble):

Name of the charging station operator

Address of the charging station

Plug with availability and information about

charging power

Opening times

Name of the charging station

Travel time and distance of the charging sta-

tion from the vehicle

Authentication method

Contact information of the charging station

operator

General costs and charging costs

Estimated charging costs and your available

energy volumes, if available

Display of available reviews and the ability to

review with up to ve stars

Availability prognosis

Information on green charging

Mercedes-Benz provides high-quality certi-

cates of origin to ensure that an equivalent

amount of electricity from renewable sources

is fed into the grid for charging processes car-

ried out via Mercedes me Charge.

Calculate the route (/ page 537).

If the function is available, the start/stop of

the charging process can be selected.

To access a charging station remotely (start/

stop): select a charging station in the map

menu of the app or the MBUX multimedia sys-

tem.

Show the details using the widget (programme

symbol).

MBUX multimedia system

539

F167 0057 02

Select Start charging process.

The charging process starts. In addition, the

payment agreement saved with the third-party

provider is authorised.

Remote access is not available for some

charging stations. In this case use your RFID

card to activate the charging process (if avail-

able).

If required, enter the PIN for personalisation.

Conrm the action.

If required, select the connector ID from the

list shown.

The selected charging cable connector is

unlocked.

Start the charging process.

The start of the charging process is shown.

Select the Stop charging process display but-

ton in the app.

The charging process is ended.

Payment is processed automatically.

If data for third-party providers is available,

you will receive this information:

Overview of the charging process

Estimated cost

There may be dierences between the costs

listed and the costs billed.

You can watch an animation on this topic via the

following link:

▌Switching low emission zones for the route on

or o

Requirements

Mercedes me connect is available.

You have a Mercedes me connect user

account and the vehicle is connected with the

account.

The "Trac Restriction Zones" service is avail-

able and activated in the Mercedes me Portal.

The service is free of charge for three years

aer registration.

Multimedia system:

Navigation

View

Activate Traffic restrictions.

The low emission zones along the route are

shown on the digital map and in the route

overview.

Before you enter a low emission zone, you will

be shown a notication in the central display.

Plug-in hybrid: the vehicle takes zones with

trac restrictions into account and drives

electrically in these zones. These are low

emission zones and in future also zero emis-

sion zones.

Route guidance is active:

When the vehicle enters a low emission

zone, it switches to the

Electric drive pro-

gram. Electrical energy is reserved for low

emission zones ahead. Thus the vehicle

can switch to the

Hybrid drive program

when it exits a zone.

540

MBUX multimedia system

F167 0057 02

Route guidance is not active:

When the vehicle enters a low emission

zone, it switches to the

Electric drive pro-

gram.

The Traffic restrictions function is switched

o:

No low emission zones are shown on the

map.

Plug-in hybrid: when the vehicle enters a

low emission zone, there is no switch to

another drive program.

▌Overview of the Range on Map service (plug-in

hybrid)

The function is available under the following con-

ditions:

The "Range on Map" service, which is subject

to a charge, is available and activated in the

Mercedes me Portal.

The

Range option is switched on

(/ page 565).

The fuel range (purple) and the electric range

(white) are shown on the map as a closed line

around the current vehicle position.

In the following cases, there is no display on the

map:

The overall range is very large.

If the fuel level is less than 10 %.

If the electric range of the vehicle is less than

6 km.

▌Selecting a route type

Multimedia system:

Navigation

Route

Using trailer mode and online routes

The route is calculated as a fast route with a short

journey time.

Trailer mode is available if a trailer has been cou-

pled with the vehicle. If available, you can select

online routes.

Trailer mode and online routes are not availa-

ble in all countries and for all vehicles.

Select Trailer mode.

A prompt is shown in the multimedia system.

Conrm the prompt.

The arrival time at the destination takes into

account a reduced driving speed with trailer.

To use online routes: switch on the option.

Taking trac information for the route into

account

Select Dynamic route guidance r.

Select one of the options.

Explanation of the options:

Automatic

Trac reports via Live Trac Information are

taken into account (/ page 554).

Live Trac Information and FM home screen

are not available in all countries.

After asking

A prompt appears when a new route is detec-

ted with a shorter journey time based on traf-

c reports. You can continue to use the cur-

rent route or use the dynamic route instead

(/ page 542).

MBUX multimedia system

541

F167 0057 02

Off

No trac reports are taken into account for

the route.

▌Calculating alternative routes

Multimedia system:

Navigation

View

Switch on Overview of route after start.

Alternative routes are calculated for every

route.

▌Accepting a detour recommendation aer a

prompt

Requirements:

After asking is switched on (/ page 541) in

the

Dynamic route guidance menu.

Route guidance is active.

There are trac reports for the current route.

If a new route with a shorter driving time is deter-

mined, the current and new routes will be shown.

If another application is active, a notication is

hidden.

Conrm the notication.

To accept the new route: select Accept.

To maintain the current route: select Keep to

current route

▌Selecting route options

Multimedia system:

Navigation

Route

Avoid options

Avoiding or using route sections, e.g. motorways

or ferries

Activate or deactivate the avoid option.

Avoid: the option is activated. The route avoids

motorways, for example.

Use: the option is deactivated. The route takes

motorways into consideration, for example.

The selected route options cannot always be

taken into account. Therefore, a route may

include a ferry, for instance, even though the

Avoid ferries avoid option is enabled. A mes-

sage then appears and you will hear a corre-

sponding message.

Avoiding or using toll roads

The use of toll roads requires a usage fee (toll).

Select Toll roads r.

Activate or deactivate Avoid all.

If the option is activated, the route avoids toll

roads.

If the option is deactivated, the route takes toll

roads into account.

Select an option for Payment by cash or card

or Electronic billing.

Avoid: the route avoids toll roads with the

selected method of payment.

Use: the route takes into account roads that

require a toll corresponding with the payment

type selected.

Avoiding or using roads requiring a special toll

sticker

A vignette allows for the use of a route network

for a limited time period.

Select Avoid vignette roads r.

Activate or deactivate Avoid all.

542

MBUX multimedia system

F167 0057 02

Switch individual countries on or o in the list.

Avoid: the option is activated. The route avoids

roads requiring a special toll sticker in the

selected countries.

Use: the option is deactivated. The route takes

into account roads in the selected country

which require you to pay a time-based fee

(vignette).

These route options are not available in every

country.

Avoiding or using areas with low emission zones

The function is available when there is an

active internet connection.

Activate or deactivate Area with low emission

zones

Avoid: the option is activated. The route avoids

all low emission zones restricted for the vehi-

cle. These are displayed in red on the map.

Use: the option is deactivated. The restricted

low emission zones for the vehicle are passed

through on the route. A warning is displayed

before you drive into a low emission zone.

Avoiding areas

Select Avoid areas r (/ page 562).

▌Selecting notications for the route

Requirements:

For an audible indication when approaching a

personal POI: the USB device contains per-

sonal POIs.

The USB device is connected with the multi-

media system.

The category in which the personal POI

belongs is activated.

Multimedia system:

Navigation

Messages & tones

Switching navigation announcements on or o

Activate Reduced messages.

If a driving instruction is available for a simple

change in direction, you hear a brief

announcement, e.g. "turn right in 200 m". The

number of driving instructions along the route

is minimised.

Activate Detailed messages.

If a driving instruction is available and there is

a complex driving situation, you hear supple-

mentary information, e.g. "In 200 m turn right

and continue to follow the major road". Addi-

tional driving instructions are issued for the

route, for example on turning major roads.

Activate Announce street names.

The name of the street into which the vehicle

should turn is announced.

This option is not available in all countries and

languages.

Switching trac announcements on or o

Activate or deactivate Announce traffic warn-

ings

If available, trac warnings are announced,

e.g. before the end of trac jams that pose a

risk.

Audible indication when approaching a personal

POI

Select Personal POIs.

MBUX multimedia system

543

F167 0057 02

Activate a category.

When approaching a personal POI in the

selected category an audible indication will be

issued.

▌Displaying a route overview

Requirements:

A destination is entered.

Multimedia system:

Navigation

Example: route guidance is active

Enters an address or POI

Destination and time of arrival

beneath that the current distance to the des-

tination and the chequered ag

Alternative routes

Searches for parking

Switches trac information display on or o

Makes settings for View, Messages & tones

and Route

When route guidance is active, the destination

and entered intermediate destinations are shown.

Depending on the route, trac situation and avail-

able data, further information is displayed:

Name, destination address

Symbols for intermediate destination and des-

tination

Phone number (if available)

Web address (if available)

Trac information

The route can include up to four intermediate des-

tinations.

Select one of the options.

▌Planning routes

Multimedia system:

Navigation

Enter the intermediate destination

(/ page 37).

Aer entering the destination and new calcu-

lation of the route, the route overview is

shown again. The route contains a new inter-

mediate destination.

If there are already four intermediate destina-

tions, delete an intermediate destination

(/ page 544).

▌Editing a route with intermediate destinations

Requirements:

The destination and at least one intermediate

destination have been entered.

Multimedia system:

Navigation

Changing the order of the destinations

In the route overview, press and hold on a

destination.

544

MBUX multimedia system

F167 0057 02

Move the destination with = or Ì.

Tap on ø.

The editing mode is ended.

Deleting a destination

In the route overview, press and hold on a

destination.

Tap on E.

The editing mode is ended.

▌Displaying the route list

Multimedia system:

Navigation

Tap on navigation window 7 on the digital

map (/ page 530).

Example: route list

Upcoming manoeuvre with turning arrow, dis-

tance to manoeuvre, street number, street

name

Ì Switches on navigation announcements

. Switches o navigation announcements

Including the following route sections on the

route to the destination

Current vehicle position

The route sections are displayed in the navigation

window. The route list is updated during the jour-

ney.

Motorway information shows the available

service facilities. Aer selecting symbols, e.g.

for car parks, service areas or motorway exits,

the POI is adopted as an intermediate destina-

tion or destination.

Press the arrow at the bottom of the naviga-

tion window briey.

Swipe up or down.

Select a route section.

The map section is displayed.

To return to vehicle position: select Current

position

▌Selecting an alternative route

Requirements:

A route has already been created.

The

Overview of route after start option is

switched on (/ page 542).

MBUX multimedia system

545

F167 0057 02

Multimedia system:

Navigation

Other routes

Example: alternative routes

Original route is highlighted

Alternative routes with indication of the dier-

ence in driving time

In 2 a faster route may also be shown that is

considerably longer.

The following route information is displayed:

Driving time

Time of arrival

Distance to the destination

Avoid options based on the set route options

Driving time saved or lost compared with the

original route

When the alternative routes have been calcu-

lated, display the route in the navigation win-

dow by swiping to the right or le.

Changing route type

Select Filter.

Switching the route type on or o.

Avoiding or using route options

Select Filter.

Switch the route options on or o

(/ page 542).

Conrm the settings with Finished.

To start route guidance to the alternative

route: select Start.

To select an alternative route on the map:

touch any point on the alternative route.

The alternative route is highlighted.

▌Activating a commuter route

Requirements:

You have created a prole (/ page 497).

The

Allow destination suggestions option is

switched on (/ page 498).

The

Commuter route option is switched on .

The multimedia system has gathered sucient

data in order to show destination suggestions.

Routes have been learned for these destina-

tion suggestions.

Route guidance is not active.

This commuter route is not available in all

countries.

Multimedia system:

Navigation

Route

Activate Commuter route.

The navigation system automatically detects

that the vehicle is on a commuter route.

For the daily commuter route, trac incidents

on the route are also reported when driving

without active route guidance.

546

MBUX multimedia system

F167 0057 02

To select commuter route: select Start.

Route guidance begins without spoken driving

instructions.

A commuter route is suggested even with

delays on the route.

To delete a commuter route: select ¨.

▌Switching the automatic lling station search

on or o

Multimedia system:

Settings

Vehicle

Select Driving.

Activate or deactivate Automatic filling sta-

tion search

Automatic filling station search is switched

on, a notication appears in which the search

for lling stations is started.

▌Starting an automatic lling station search

Requirements

The automatic lling station search is activa-

ted (/ page 547).

Driving situation

The fuel level in the fuel tank reaches the reserve

fuel level.

The following notication is shown on the central

display:

Fuel reserve Tap here to search for fill-

ing stations.

Conrm the notication.

The automatic lling station search begins.

The available lling stations along the route or

in the vicinity of the vehicle's current position

are displayed.

Select a lling station.

Calculate the route with the lling station as

an ¦ intermediate destination or as a

¥ destination (/ page 537).

If there are already four intermediate destina-

tions: select Yes in the prompt.

The selected lling station is entered in the

route overview at position 1. Intermediate des-

tination 4 is deleted. Route guidance begins.

▌Starting the automatic service station search

Requirements

ATTENTION ASSIST is activated

(/ page 368).

You are driving on a motorway.

There are service stations along the route sec-

tion ahead.

Driving situation

The following notication is shown on the media

display ATTENTION ASSIST Tap here to search

for rest areas.

Conrm the notication.

The service station search starts. The availa-

ble service stations along the route or in the

vicinity of the vehicle's current position are

displayed.

Select a service station.

Calculate the route with the service station as

an ¦ intermediate destination or as a

¥ destination (/ page 537).

MBUX multimedia system

547

F167 0057 02

If there are already four intermediate destina-

tions: select Yes in the prompt.

The selected service station is entered in the

route overview at position 1. Intermediate des-

tination 4 is deleted. Route guidance begins.

▌Starting and editing a stored route

Requirements:

A USB device with stored routes is connected

with the multimedia system (/ page 620).

The route is stored in the "Routes" folder with

the GPS Exchange format (.gpx).

Multimedia system:

Navigation

Press the double arrow in the destination

input line until

Stored routes is displayed.

Select Stored routes.

Starting a saved route

Select a route.

Select Start: route guidance at start or Start:

current location

Route guidance begins.

Renaming a route

Press on a route until a menu is shown.

Select Rename.

Enter the name.

Select OK.

▌Recording and storing a route

Requirements:

A USB device is connected with the multime-

dia system (/ page 620).

Multimedia system:

Navigation

Press the double arrow in the destination

input line until Stored routes is displayed.

Select Stored routes.

Starting recording

Select Start recording.

A white rectangle is displayed.

The route is stored on the USB device.

Stopping recording

Press the white rectangle.

Select End recording.

Route guidance

▌Notes on route guidance

WARNING Risk of distraction from operat-

ing integrated communication equipment

while the vehicle is in motion

If you operate communication equipment inte-

grated in the vehicle when driving, you could

be distracted from the trac situation. This

could also cause you to lose control of the

vehicle.

Only operate this equipment when the

trac situation permits.

If you cannot be sure of this, stop the

vehicle whilst paying attention to road

and trac conditions and operate the

equipment with the vehicle stationary.

548

MBUX multimedia system

F167 0057 02

You must observe the legal requirements for the

country in which you are currently driving when

operating the multimedia system.

Route guidance begins once a route has been cal-

culated. The road and trac rules and regulations

always have priority over multimedia system driv-

ing instructions. Driving instructions are, for

example navigation announcements, changes in

direction and lane recommendations.

Changes in direction and lane recommendations

are shown in the navigation window.

The following displays and functions are also avail-

able in the navigation window, for example:

Route list

Destination information

Trac information, e.g. length of trac jam,

delay

Motorway facilities

Car park search

Emergency corridors

If you do not follow the driving instructions or if

you leave the calculated route, a new route is cal-

culated automatically.

If, for example, the route is diverted or the direc-

tion of a one-way road has been reversed, driving

instructions may deviate from the actual trac

situation.

Alternatives may be oered during route guid-

ance, e.g. before passing a motorway exit road.

The additional driving time for the journey along

the motorway exit is shown.

For this reason, you must always observe road

and trac rules and regulations during your jour-

ney as well as the prevailing trac conditions.

The route can dier from the ideal route, for

example in the event of roadworks or incomplete

digital map data.

Notes on satellite reception

The correct function of the navigation system

depends amongst other things on reception of the

satellite system used. In certain situations satel-

lite reception can be impaired, malfunction or

even not be possible, e.g. in tunnels or in multi-

storey car parks.

▌Changing direction overview

Changes of direction are shown in the following

displays:

Detailed image of the junction

The display appears when you drive into a

junction.

3D image

The display appears when driving on junction-

free, multi-lane roads, for example at motor-

way exits and motorway interchanges.

MBUX multimedia system

549

F167 0057 02

Example: detailed image of the crossing with

upcoming changes of direction

Name of the street to turn into

Change of direction arrow (also on the map)

Current vehicle position

Current distance to the change of direction

Example: 3D image of the upcoming change

of direction

Manoeuvre point

Change of direction arrow (also on the map)

Larger map scales show change of direction

points instead of change of direction arrows.

Current distance to the change of direction

Current vehicle position

There are three phases when changing direction:

Preparation phase

If there is enough time between the changes

of direction, the multimedia system prepares

you for the upcoming change of direction. A

navigation announcement is issued, e.g. "Pre-

pare to turn right".

The navigation window shows: the direction

information or the name of the road which is

to be turned into as well as the distance to the

change of direction.

Announcement phase

The multimedia system announces the upcom-

ing change of direction, e.g. by announcing

"Turn right in 300 m".

When the

Auto zoom map orientation is

switched o (/ page 564), a detailed repre-

sentation of the junction or a 3D image of the

upcoming change in direction appears in the

navigation window.

Change-of-direction phase

The multimedia system announces the immi-

nent change of direction, e.g. by announcing

"Now turn right".

Example of 3D image: when the distance to

manoeuvre point

1 is shown with 0 m and

the symbol for current vehicle position

4 has

550

MBUX multimedia system

F167 0057 02

reached manoeuvre point 1 the change in

direction is carried out.

Changes in direction are also displayed on the

driver display and head-up display.

▌Lane recommendations overview

Example: lane recommendations

Non-recommended lane (grey arrow)

Possible lane (white arrow)

Recommended lane (white arrow, blue back-

ground)

This display appears for multi-lane roads.

If the digital map contains the relevant data, lane

recommendations are displayed in the navigation

window.

Explanation of the displayed lanes:

Recommended lane

In this lane, you will be able to complete both

the next change of direction and the one aer

that.

Possible lane

In this lane, you will only be able to complete

the next change of direction.

Non-recommended lane

In this lane, you will not be able to complete

the next change of direction without changing

lane.

During the change of direction, new lanes may be

added. Bus lanes are also shown.

Lane recommendations are also displayed on

the driver display and head-up display.

▌Using motorway information

When driving on the motorway, upcoming motor-

way facilities and available service facilities are

shown in the route list. These include car parks,

service stations or motorway exits with service

POIs, for example.

The entries are sorted according to increasing dis-

tance from the current vehicle position.

Select an entry.

If several service facilities are available, select

a service facility from the list.

The destination address and the map position

are shown.

Calculate the route (/ page 537).

Search for a POI in the vicinity.

Use other functions, e.g. store the destination

address of the service facility.

▌Destination reached

Once the destination is reached, you will see the

Í chequered ag. Route guidance will now be

complete. The navigation menu is shown.

When an intermediate destination has been

reached, you will see the intermediate destination

MBUX multimedia system

551

F167 0057 02

ag with the number of your Î intermediate

destination. Route guidance is continued.

▌Switching navigation announcements on or o

Switching o

During a navigation announcement, press the

Ì button on the steering wheel or control-

ler in the centre console.

The

Spoken driving recommendations have

been deactivated.

message appears.

In the route list for a driving manoeuvre

select . (/ page 545).

The symbol changes to Ì.

Switching on

Press the button on the steering wheel or on

the controller in the centre console again.

In the navigation window, select Ì for an

upcoming driving manoeuvre.

The current navigation announcement is

played.

The symbol changes to ..

Switching navigation announcements on or o

during a phone call

Press the © button on the steering wheel

on the right.

Tap on © in the media display.

Select Settings.

Select System.

Select Audio.

Select Navigation & traffic announcements.

Activate or deactivate Driving recommenda-

tions during call

To leave the menu: select G.

▌Adjusting the volume of navigation announce-

ments

Multimedia system:

Settings

System

Audio

Navigation & traffic announcements

Select Driving recommendation vol..

Set the volume.

To leave the menu: select G.

Route guidance is active

During a navigation announcement, adjust the

volume on the steering wheel or on the con-

troller in the centre console (/ page 489).

Switching audio fadeout on or o during naviga-

tion announcements

Press the © button on the steering wheel

on the right.

Tap on © in the media display.

Select Settings.

Select System.

Select Audio.

Select Navigation & traffic announcements.

Activate or deactivate Audio fadeout during

navigation announcements

To leave the menu: select G.

▌Repeating navigation announcements

Requirements:

A route has already been created.

552

MBUX multimedia system

F167 0057 02

Route guidance is active.

Multimedia system:

Navigation

In the navigation window, select . for an

upcoming driving manoeuvre.

Select Ì.

The current navigation announcement is

repeated.

▌Cancelling route guidance

Requirements:

A route has already been created.

Route guidance is active.

Show the navigation menu.

Select ¤ in the navigation menu

(/ page 530).

▌Overview of o-road status during route guid-

ance

Due to roadworks, for example, there may be dif-

ferences between the data on the digital map and

the actual course of the road. In such cases, the

multimedia system will temporarily be unable to

locate the vehicle's current position on the digital

map. The vehicle is o-road.

Road not mapped

will be shown. Route guidance may be restricted.

When the vehicle is back on a road known to the

multimedia system, route guidance continues as

normal.

Destination

▌Saving the current vehicle position

Multimedia system:

Navigation

When the map is shown, tap on the ¥ cur-

rent vehicle position.

Select Store position.

To save as a favourite: select Save as favour-

ite

To save as "Home" address: select Home .

To save as "Work" address: select Work .

▌Managing previous destinations

Multimedia system:

Navigation

Select Previous destinations.

Select Ä for the last destination.

Saving the last destination as a favourite

Press and hold on one of the previous destina-

tions.

A menu appears.

To save as a favourite: select Save as favour-

ite

To save as "Home" address: select Home .

To save as "Work" address: select Work .

Deleting a previous destination

Select Previous destinations.

For a last destination, select Ä.

Select Delete.

Select Delete all.

MBUX multimedia system

553

F167 0057 02

Conrm the prompt.

When all the favourites have been deleted,

Add favourite is available, for example.

▌Editing destination suggestions

Requirements:

The

Allow destination suggestions option is

switched on (/ page 512).

For the display of destination suggestions: the

multimedia system has gathered sucient

data.

Multimedia system:

Navigation

Select Suggestions.

Press and hold on a destination suggestion.

A menu appears.

To cancel a destination suggestion: select Do

not suggest now

or No longer suggest.

To save a destination suggestion: select Save

as favourite

, Home or Work.

Delete a destination suggestion from the

favourites (/ page 536).

Route guidance with current trac reports

▌Trac information overview

Current trac reports are received with the Live

Trac Information subscription service.

If the subscription has expired, then FM RDS-TMC

is available in selected countries.

Live Trac Information is not available in all

countries.

The service must be registered in the Mercedes

me user account (/ page 555). This secures the

free-of-charge period of three years.

The service updates the trac situation via the

Internet connection at short, regular intervals.

Information on the vehicle's position is regularly

sent to Mercedes-Benz AG. The data is immedi-

ately rendered anonymous by Mercedes-Benz AG

and forwarded to the trac data provider. Using

this data, trac reports relevant to the vehicle's

position are sent to the vehicle. The vehicle acts

as a sensor for the ow of trac and helps to

improve the quality of the trac reports.

There may be dierences between the trac

reports received and the actual road and traf-

c conditions.

If you do not want to transmit the vehicle position,

you have the following options:

You deactivate the service in the Mercedes

me user account.

You have the service deactivated at a

Mercedes-Benz service centre.

Further hazard warnings are received using

the Car-to-X service (/ page 557).

▌Showing information from the service provider

for Live Trac Information

Requirements

The vehicle is equipped with Live Trac Infor-

mation.

Multimedia system:

Apps

Mercedes me

My services

Select Live Traffic.

554

MBUX multimedia system

F167 0057 02

When the subscription for Live Trac Information

has expired then in selected countries FM RDS-

TMC is available.

▌Registering Live Trac Information

Requirements:

The vehicle is equipped with Live Trac Infor-

mation.

You have a Mercedes me user account.

Create a Mercedes me user account at:

.. A valid email

address is required for this.

cation number (VIN).

Connect the vehicle with your Mercedes me

user account.

A code is sent to the multimedia system.

Enter the code into the multimedia system.

Accept the general and specic terms of use.

Alternatively, you can have the connection

completed at a Mercedes-Benz service

centre.

▌Extending a Live Trac Information subscrip-

tion

Requirements:

The vehicle is equipped with Live Trac Infor-

mation.

You have a Mercedes me user account.

Call up the Mercedes me website.

Call up the Mercedes me user account.

Switch to the Mercedes me Store via the

linked vehicle.

Select Live Trac Information.

Select the renewal period.

Add the product to the shopping basket.

Accept the general and specic terms of use.

Live Trac Information remains activated for

the selected extension period. Activation

begins on the date of extension.

▌Displaying trac information on the map

Requirements:

Traffic incidents and Free-flowing traffic are

switched on (/ page 557).

Multimedia system:

If necessary, move the map (/ page 560).

The map shows the following trac information

depending on the activated settings:

Trac incidents

These are roadworks, road blocks and warning

messages, for example.

When route guidance is active, the symbols for

trac incidents will be shown in colour on the

route. O the route they are grey.

Warning messages

Warning messages are shown as the d

symbol.

Trac safety information can be shown, e.g. if

there are people on the carriageway.

If the vehicle approaches a danger area, for

example the end of a trac jam in a danger-

ous position, the Ë symbol is shown on

the map. If

Announce traffic warnings is

switched on and a message has been issued,

an additional announcement is made.

MBUX multimedia system

555

F167 0057 02

Trac ow information:

Trac jam (red line)

Slow-moving trac (orange line)

Heavy trac (yellow line)

Free-owing trac (green line)

Display for trac delays on the current route

The smallest value for the display for trac

delays is a minute.

▌Showing trac incidents on the route

Requirements:

The

Traffic incidents display is switched on

(/ page 557).

Multimedia system:

Navigation

If there are trac incidents on the route, these

are shown on the map and in the route overview.

With the MBUX Voice Assistant you can

inform yourself about trac incidents on your

route. Ask, for example How is the traffic on

my route? or How is the traffic at home?. A

voice output is issued.

Example: trac incidents on the route

Total delay or message that there are no

delays along the route

Switches trac information display on or o

Calls up settings for View, Messages & tones

and Route

If there are any delays along the route, these are

shown in the route overview together with the fol-

lowing information:

Trac jam section: red bars

Slow-moving trac: orange bar

Heavy trac: yellow bar

For each section:

The delay

The length

The street name or the street number

During active route guidance, the total delay

on the route is also displayed here:

in the navigation system in the navigation

module

in other applications in the status line at

the top

Trac incident symbols are shown in the

route overview and in the map. A trac inci-

dent symbol is, for example Ò for road-

works.

In the map several trac incidents may be

shown on top of each other. The trac inci-

dent symbol shows a plus sign.

If available, the street number can be

replaced by a street name or both the name

and number.

If a message about forming an emergency

corridor has been issued, Emergency corridor

is shown in the navigation window.

556

MBUX multimedia system

F167 0057 02

To see all of the trac incidents on the route,

swipe to the right or le.

The route section is highlighted on the map.

To show detailed information in the route over-

view: tap on a display in the route overview.

The detailed information is shown, for example

the road section and the direction.

Calling up detailed information on the map

Tap on trac ow information on the map,

e.g. a red line for a trac jam section.

The detail information is displayed.

If several lines are shown on top of the other,

then select an item of trac ow information

from the list.

Showing trac incidents on the map

Tap on a trac incident symbol.

The detail information is displayed.

Several trac incidents are in the immediate

vicinity: tap on the top trac incident symbol

and select from the list of trac incidents.

▌Switching the trac information display on

Multimedia system:

Navigation

Select View.

Traffic

Activate Traffic incidents and Free-flowing

traffic

Trac incidents, for example roadworks, local

area reports (e.g. fog) and warning messages,

are shown on the route.

Car-to-X-Communication

▌Car-to-X-Communication overview

The following requirements apply for the Car-to-X-

Communication service:

The vehicle is equipped with an MBUX multi-

media system with navigation function.

There is a subscription for the Live Trac

Information service.

The Car-to-X-Communication service is activa-

ted in your Mercedes me user account.

Car-to-X-Communication is available in selec-

ted countries.

The communication module automatically estab-

lishes an Internet connection once the vehicle is

switched on. If there are any hazard warnings,

they will be provided shortly thereaer. Depend-

ing on the mobile phone connection, provision

takes place from within a second up to about a

minute.

Benets of Car-to-X-Communication:

Dangers are automatically detected by the

vehicle or can be reported by the driver. These

are then sent to vehicles with Car-to-X-Com-

munication in the immediate vicinity.

If available, current details relating to hazard

spots near the vehicle's current position are

received.

This gives you sucient time to adapt your

driving style to the trac conditions.

The use of Car-to-X-Communication requires the

regular transmission of vehicle data to Mercedes-

Benz AG. The data is then immediately pseudony-

mised by Mercedes-Benz AG. The vehicle data is

MBUX multimedia system

557

F167 0057 02

deleted aer an appropriate amount of time has

elapsed (several weeks) and is not stored perma-

nently.

Data which serves as identication is

replaced during the pseudonymisation proc-

ess. In this way, your identity is protected

against access by unauthorised third parties.

▌Displaying hazard warnings

Multimedia system:

Navigation

If hazard warnings are available these can be

shown as symbols on the map. The display

depends on the settings for the Traffic incidents

option.

Set the option via Z (/ page 557).

If the option is activated, all of the symbols are

shown.

If the option is deactivated, the symbols are

only shown when there is a hazard warning.

The following hazards may be shown on the map:

Accidents and breakdowns

Slippery roads, fog, crosswinds and heavy rain

Hazards reported manually

Vehicle with active hazard warning light

Roadworks

Additional hazards (if available)

If Announce traffic warnings is switched o

(/ page 543), voice output can indicate a

danger area.

▌Sending hazard warnings

Reporting hazards manually

Automatically detected hazard warnings are

sent by the vehicle.

When the map is shown, tap on the ¥ cur-

rent vehicle position.

The

Position menu is shown.

Select Report traffic incident.

A prompt is shown.

Select Yes.

The

Thank you for supporting accident pre-

vention!

message appears.

Route guidance with augmented reality

▌Overview of route guidance with augmented

reality

WARNING Risk of accident and injury as a

result of distraction, incorrect depiction or

wrong interpretation of the display

The camera image of the augmented reality

display is not suitable as a guide for driving.

Always keep an eye on the actual trac

situation.

Avoid extended observation of the cam-

era image.

During route guidance with augmented reality a

camera image with the real trac scene is shown

in the media display before a turning manoeuvre.

The camera image includes additional informa-

tion, for example arrows indicating a change of

direction.

If the options are switched on and this additional

information is available, road names and house

numbers are displayed (/ page 559).

558

MBUX multimedia system

F167 0057 02

House number

Street name

Change of direction arrow

Route guidance with augmented reality will not be

available in some situations, e.g. in the event of

poor satellite reception or roads that have not

been digitised.

Route guidance with augmented reality is not

available in all countries.

You can watch an animation on this topic via the

following link:

▌Activating route guidance with augmented real-

ity

WARNING Risk of accident and injury due

to imprecise positioning of additional

information

The additional information from the augmen-

ted reality display may be inaccurate and is

not a substitute for observing and assessing

the actual driving situation.

Always keep an eye on the actual trac

situation when carrying out all driving

manoeuvres.

Multimedia system:

Navigation

Select View.

Select Augmented reality video.

Activate or deactivate Augmented reality

video

The camera's video image is shown on the

media display before a turning manoeuvre.

The video image includes additional informa-

tion.

▌Showing property information for route guid-

ance with augmented reality

Requirements:

Augmented reality is activated (/ page 559).

Multimedia system:

Navigation

Select View.

Select Augmented reality video.

Activate Street names and House numbers.

During route guidance, the activated options

are shown as additional information in the

camera image.

MBUX multimedia system

559

F167 0057 02

Map and compass

▌Setting the map scale

Multimedia system:

Navigation

Zooming in

When the map is shown, tap twice quickly with

one nger on the media display.

Move two ngers apart on the media display.

Zooming out

Tap with two ngers on the media display.

Move two ngers together on the media dis-

play.

You can set the unit of measurement of the

map scale (/ page 512).

▌Moving the map

Multimedia system:

Navigation

When the map is displayed, swipe in any direc-

tion with one nger on the media display.

The following functions are available:

Selecting a destination on the map

(/ page 536).

Selecting a POI (/ page 533).

Showing trac incidents on the map

(/ page 556).

To reset the map to the current vehicle posi-

tion: select \ Centre .

▌Switching the route overview aer start on or

o

Multimedia system:

Navigation

Select View.

Activate D or deactivate E Overview

of route after start

If the option is enabled, the map shows the full

route aer route guidance is started and, if

available, all alternative routes.

▌Selecting POI symbols for the map display

Multimedia system:

Navigation

POIs include restaurants and hotels, for example.

These are displayed as symbols on the map. Not

all POIs are available in all countries.

Personal POIs are destinations which you have

saved on a USB device, for example.

The display of POI symbols on the map can be

activated or deactivated as a favourite.

Select View.

Select POI symbols on map r.

Switch on Hide all points of interest.

When the option is switched on, the POI sym-

bols for all categories are shown on the map

according to the settings in the POI catego-

ries.

560

MBUX multimedia system

F167 0057 02

If the conditions are fullled, the POI symbols

are shown with current online information

(/ page 565).

Switching display of categories for quick-access

on or o

Switch a category on or o in the menu.

Selecting categories

In the menu, select Other categories r.

Activate or deactivate Show all.

When the option is switched on, the POI sym-

bols for all categories are shown on the map.

Select r the categories.

Activate or deactivate the categories.

The POI symbols for the selected categories

are shown on the map.

Selecting personal POI categories

In the menu, select Personal POIs r .

Select r a category.

Activate or deactivate Display on the map.

To issue a signal when approaching: activate

Visual warning and Acoustic notification.

Resetting the POI symbol display

In the menu, select Reset POIs.

The settings are reset to the standard set-

tings.

▌Selecting the display of additional information

on the map

Multimedia system:

Navigation

Select View.

Select Show additional information.

Switch the options on or o.

The following options are available:

Current street

If the option is enabled, it will be displayed in

the navigation window.

Scale

If the option is switched o, the map scale is

only displayed on the map when zooming.

If the option is enabled, the map scale is per-

manently displayed on the map.

The option also inuences the display on the

driver's display.

Altitude

Next junction

If the option is switched on and the journey

continues without route guidance, the name of

the next intersecting street will be displayed in

the navigation window.

▌Displaying the map version

Multimedia system:

Navigation

Select View.

Select Map data version.

The detail information is displayed.

The online map update service from

Mercedes me connect can be used to update

the map data (/ page 37).

A message is shown in the media display

when a new map version is available.

MBUX multimedia system

561

F167 0057 02

Information about new versions of the digital

map can be obtained from a Mercedes-Benz

service centre.

▌Overview of area avoidance on the route

You can dene areas along a route that you would

like to avoid.

Motorways or multi-lane expressways that pass

through an area to be avoided may be included in

the route despite being blocked.

▌Avoiding a new area for the route

Multimedia system:

Navigation

Route

Avoid areas

Select Avoid new area.

Starting using the map

Select Using map.

A red rectangle appears. This designates the

area that should be avoided.

Move the map (/ page 560).

Set the map scale (/ page 560).

Select a.

The area is entered into the list.

Starting using destination search

Select Via address entry.

Enter the address (/ page 37).

Select the destination in the list.

The map appears. The area is saved.

▌Changing an area to be avoided

Multimedia system:

Navigation

Route

Avoid areas

Select an area in the list.

Select Edit.

To move an area on the map: swipe in any

direction on the media display.

Changing the size of the area

Move two ngers apart or together on the

media display.

Select a.

The area is entered into the list.

Taking the area for the route into account

Select the area in the list.

Activate Avoid area.

If route guidance is active, a new route is cal-

culated.

If there is no route yet, the setting is carried

over to the next route guidance.

The route can include an area that is to be

avoided in the following cases:

The destination is located in an area that is

to be avoided.

The route includes motorways or multi-

lane expressways which pass through an

area to be avoided.

There is no practical alternative route.

▌Deleting an area to be avoided

Multimedia system:

Navigation

Route

Avoid areas

Deleting an area to be avoided

Select an area in the list.

562

MBUX multimedia system

F167 0057 02

Select Delete.

Conrm the prompt with Yes.

Deleting all areas to be avoided

If at least two areas to be avoided are set,

select Delete all.

Conrm the prompt with Yes.

▌Map data update overview

As the content of a digital road map has a short

life, outdated data may have a negative eect on

all navigation functions. For the best MBUX navi-

gation experience, you should install all of the

map updates oered by Mercedes-Benz.

The following options are available for the update

of map data:

Online map update

Updates from the Mercedes me Portal

Update at a Mercedes-Benz service centre

Additional costs can be incurred in this proc-

ess.

Online map update

Requirements:

Mercedes me connect is available.

You have a Mercedes me user account.

The Online Map Update service is available for

your region.

The service has been activated.

The Online Map Update service is only availa-

ble in certain countries.

Installation takes place in the background as an

automatic map update.

The MBUX multimedia system installs all of the

available map updates for the European regions in

which the vehicle is located or is moved.

The online map update is activated at the latest

aer the next time the vehicle is switched on.

Updates from the Mercedes me Portal

The map data for several regions can also be

updated manually. Log in with your Mercedes me

user account at: .mercedes-

Follow the menu path

My Mercedes Me account

> My vehicles > Selection of car > Online Map

Update

. Select the regions to be downloaded to a

storage medium.

Aer the map data has been copied, connect the

storage medium with your vehicle. Select the noti-

cation with information about a new version of

the map data and start the installation. Aer the

MBUX multimedia system has been restarted, the

updated map data is used.

▌Overview of map data

If map data is reinstalled in a vehicle, no activa-

tion code needs to be entered.

For map data purchased as data media, the

enclosed activation code must be entered aer

starting the installation.

Activation codes are only ever valid for one vehi-

cle.

In the event of the following problems, please

contact a Mercedes-Benz service centre:

The multimedia system does not accept the

activation code.

You have lost the activation code.

MBUX multimedia system

563

F167 0057 02

▌Displaying the compass

Multimedia system:

Navigation

When the map is shown, tap on the ¥ cur-

rent vehicle position until the

Position menu is

shown.

Select Compass.

The compass display shows the following

information:

The current direction of travel with bearing

(360° format) and compass direction

Longitude and latitude coordinates in

degrees, minutes and seconds

Number of satellites from which a signal

can be received

The information is not available in every country.

▌Displaying Qibla

Multimedia system:

Navigation

When the map is shown, tap on the ¥ cur-

rent vehicle position until the

Position menu is

shown.

Select Alerts.

The arrow on the compass shows the direc-

tion to Mecca in relation to the current direc-

tion of travel.

The number of satellites received is shown.

This function is not available in all countries.

▌Setting the map scale automatically

Multimedia system:

Navigation

Select View.

Activate D Auto zoom.

When the option is switched on, the map scale

is set automatically depending on your driving

speed and the type of road.

The automatically selected map scale can be

changed manually. Aer a few seconds, this is

automatically reset.

When the option is activated, no detailed dis-

play of the junction or a 3D image is shown in

the navigation window during an upcoming

driving manoeuvre.

▌Displaying the satellite map

Multimedia system:

Navigation

Select View.

Activate or deactivate Satellite map.

When

Satellite map is selected, they are dis-

played at the following map scales:

On-board maps

The satellite maps are displayed in map

scales from 2 km.

Online maps

The satellite maps are displayed in high-

resolution map scales from 10 m.

When

Satellite map is not selected, no satel-

lite maps are displayed.

564

MBUX multimedia system

F167 0057 02

The satellite maps for these map scales are

not available in all countries.

▌Displaying the range

Requirements:

There is an Internet connection.

Mercedes me connect is available.

You have a Mercedes me user account.

The vehicle is connected with the user

account and you have accepted the Mercedes

me connect terms of use.

Further information can be found at:

www.

The service is available and has been activa-

ted.

Multimedia system:

Navigation

Display of the total range

Select View.

Range

The range is shown on the map with the following

displays:

For petrol and diesel vehicles: green display

For hybrid vehicles:

Total range: green display

Electrical range: blue display

When the lower reserve capacity is reached then

the range display on the map is switched o.

The range display on the map is not available

in all countries.

▌Displaying online map contents

Requirements:

There is an Internet connection.

Mercedes me connect is available.

You have a Mercedes me user account.

The vehicle is connected with the user

account and you have accepted the Mercedes

me connect terms of use.

Further information can be found at:

www.

The service is available and has been activa-

ted.

Multimedia system:

Navigation

Select View.

MBUX multimedia system

565

F167 0057 02

Switch on an online service, e.g. Weather.

Current weather information is displayed on

the navigation map, e.g. temperature or cloud

cover.

The service information is not shown in all

map scales, e.g. weather symbols.

The display of online map content is not avail-

able in all countries.

Parking service

▌Notes on the parking service

NOTE Vehicle damage due to failure to

observe the maximum permissible clear-

ance height

If the vehicle height exceeds the maximum

permissible clearance height, the roof and

other vehicle parts may be damaged.

Please observe the indicated maximum

clearance height.

If the vehicle exceeds the permissible

clearance height, do not drive in.

Take the modied vehicle height in the

case of roof superstructures or other

carrier systems into account.

This service is not available in all countries.

▌Displaying parking options on the map

Requirements:

Navigation Services is activated in your

Mercedes me user account.

The parking service is part of the scope of the

Navigation Services.

Multimedia system:

Navigation

Switch on Parking.

The parking options within the vicinity of the

current vehicle position are shown.

▌Selecting parking options

NOTE Vehicle damage due to failure to

observe local information and parking

conditions

The data is based on the information provided

by the respective service providers.

Mercedes-Benz does not guarantee the accu-

racy of the information provided in relation to

the car park or parking area.

Always observe the local information and

conditions.

Requirements:

Navigation Services is activated in your

Mercedes me user account.

The parking service is part of the scope of the

Navigation Services.

Parking is activated (/ page 566).

Multimedia system:

Navigation

Tap on j on the map.

566

MBUX multimedia system

F167 0057 02

In the route overview, select j Parking

spaces

(/ page 544).

Select the search position and search lter,

e.g. Near destination and Multi-storey car

parks

The map shows car parks suited to the selec-

ted settings.

Select a parking option.

The following information is displayed (if avail-

able):

Destination address, distance from current

vehicle position and arrival time

Information on the car park, e.g.

Opening times

Parking charges

Current occupancy

Maximum parking time

Maximum access height

The maximum access height shown by

the parking service does not replace

the need for observation of the actual

circumstances.

Available payment options (Mercedes pay,

coins, bank notes, cards)

Details on parking taris

Number of available parking spaces

Payment method (e.g. at parking meters)

Services/facilities at the parking option

Telephone number

Calculate the route (/ page 537).

The following functions can be used (if availa-

ble):

Searching for POIs in the vicinity.

Saving the destination.

Placing a call at the destination.

Sharing the destination via the QR code.

Calling up the web address.

Showing the destination on the map.

▌Prior booking of a parking space

Requirements:

Navigation Services is activated in your

Mercedes me user account.

The parking service is part of the scope of the

Navigation Services.

You have registered with your payment details

for the payment of parking in the Mercedes

me Portal with Mercedes pay and the respec-

tive contract partner.

Parking is activated (/ page 566).

This option is not available in all countries.

Multimedia system:

Navigation

Select a parking option on the map.

If a parking space available to book has been

selected, select Book parking space.

Select the desired booking period. Take note

of the cancellation conditions.

If the parking space is available for the selec-

ted period, the price will be shown.

MBUX multimedia system

567

F167 0057 02

Press a to conrm.

In the booking overview, conrm with Book.

If required, enter the Mercedes me PIN.

The parking space will be booked in the back-

ground.

A booking conrmation including a car park

ticket will be sent to your registered email

address.

Making use of or cancelling the booking

Start the Mercedes me App on your smart-

phone.

Open Menu.

Select My transactions.

Select Parking transactions.

Select the desired booking.

To make use of the booking: select Show car

park ticket

To cancel the booking: select Cancel booking.

If possible, a parking space booking can be

cancelled up to the stated time. If a booking

cannot be cancelled, this will already be

shown to you during the booking procedure.

▌Paying parking charges

Requirements:

Navigation Services is activated in your

Mercedes me user account.

The parking service is part of the scope of the

Navigation Services.

You have registered with your payment details

for the payment of parking in the Mercedes

me Portal with Mercedes pay and the respec-

tive contract partner.

Parking is activated (/ page 566).

This option is not available in all countries.

Multimedia system:

Select a parking option on the map.

If a car park that can be paid for has been

selected, scroll down in the parking details.

Select Payment.

Once the vehicle has reached a parking posi-

tion with payment function and the vehicle is

switched o, a message appears. Using this

message you can pay from the vehicle and

start the payment process.

Starting a payment procedure

Acknowledge the message.

Please note the maximum parking period dis-

played and any existing additional limitations.

If required, a message will inform you about

the necessity of displaying information con-

rming the online payment for the parking

space.

Select Start the payment process.

If required, enter the Mercedes me PIN.

Press a to conrm.

The successful start of your parking transac-

tion is shown.

Complete the booking with OK.

To cancel a parking transaction: aer receiv-

ing the conrmation request, select Cancel.

Minimum charges may be incurred.

568

MBUX multimedia system

F167 0057 02

Ending a parking transaction

Stop the active transaction using the

Mercedes me app.

You receive a summary of the procedure and

the costs.

If an uncompleted parking transaction is

detected for your vehicle as you continue your

journey, a message will appear asking whether

you would like to end it.

Acknowledge the message.

When the parking transaction is stopped suc-

cessfully, another message appears with the

details about your completed parking.

Dashcam

▌Notes on the dashcam

NOTE Risk of legal consequences due to

violation of legal regulations and data pro-

tection provisions

You are legally responsible for operation and

use of the dashcam functions.

The legal requirements relating to operation

and use of the dashcam can vary depending

on the country in which the dashcam is oper-

ated.

This function is not permitted in all countries.

Before using the dashcam, read up on

the content of the legal regulations, in

particular the data protection require-

ments in the respective country of use.

Observe the legal regulations, in particu-

lar the data protection requirements.

Observe the following instructions for safe

operation:

Only use FAT32 or exFAT formatted USB

storage devices.

Use USB-IF certied USB storage devices.

USB-IF is a non-prot corporation and

stands for USB Implementers Forum.

Based on the USB specication, USB-IF

certies, for example, USB versions, cor-

responding cables and plugs as well as

energy supply processes via the USB

interface.

USB storage devices may be damaged if

oen or permanently overwritten at high

speed. Mercedes-Benz recommends a

high-quality external SSD drive.

The abbreviation SSD stands for Solid

State Drive.

The le size and therefore the duration of sin-

gle recording is limited by the limitations of

the USB ash drive format. So FAT32 format-

ted USB ash drives do not allow les larger

than 4 GB, for example.

When the le size is reached, the recording

stops and you receive a notication.

The following functions are available in the

Gallery app:

Switching write protection on or o

Deleting video les

Additional information about the Gallery app

(/ page 600).

MBUX multimedia system

569

F167 0057 02

▌Selecting a USB device for a video recording

with the dashcam

Requirements:

At least one USB device is connected with the

multimedia system (/ page 620).

Multimedia system:

Apps

Dashcam

Select the USB symbol.

Select the USB device.

When USB devices contain multiple partitions,

recorded video les are not always displayed

in the recording list.

Mercedes-Benz recommends that you use

USB devices with one partition.

▌Starting or stopping a loop recording with the

dashcam

Requirements:

For recording and saving a video le: a USB

device is connected with the multimedia sys-

tem (/ page 620).

The vehicle is switched on.

Multimedia system:

Apps

Dashcam

If several USB devices are connected with the

multimedia system, select a USB device

(/ page 570).

If no USB device is selected, a selection is

made automatically when recording starts.

To select recording mode: select Loop record-

ing

Loop recording continuously records short

video les. When the memory is full, recording

is continued automatically. In doing so, the

oldest video le is written over.

To start: select Start recording.

The length of the recording is shown. The

not remove the storage medium during

recording. Before removing the storage

medium, eject it first.

message appears. The

video le is stored on the USB device.

To end: select End recording.

In some countries, geo-coordinates (longitude

and latitude) are shown in the video image.

For technical reasons, the geo-coordinates

may show greater inaccuracies.

A message may appear in the following cases:

The camera is not functional, the

Camera

unavailable

message appears.

Have the camera checked in a Mercedes-Benz

service centre.

If the country border indication has been

switched on (/ page 571).

If an outdoor recording is started with the

camera app during a dashcam recording, the

dashcam recording pauses and resumes auto-

matically aer the camera recording is n-

ished. A notication to this eect is displayed.

▌Starting or stopping individual recordings with

the dashcam

Requirements

For recording and saving a video le: a USB

device is connected with the multimedia sys-

tem (/ page 620).

The vehicle is switched on.

570

MBUX multimedia system

F167 0057 02

Multimedia system:

Apps

Dashcam

If several USB devices are connected with the

multimedia system, select a USB device

(/ page 570).

If no USB device is selected, a selection is

made automatically when recording starts.

To select recording mode: select Individual

recording

Individual recording stops recording when the

memory limit is reached. An individual record-

ing is automatically protected against being

overwritten.

To start: select Start recording.

The length of the recording is shown. The

not remove the storage medium during

recording. Before removing the storage

medium, eject it first.

message appears. The

video le is stored on the USB device.

To end: select End recording.

In some countries, geo-coordinates (longitude

and latitude) are shown in the video image.

For technical reasons, the geo-coordinates

may show greater inaccuracies.

A report may appear in the following cases:

Individual recording: the memory is full or

there are only a few minutes recording time

available. The video recording stops or will be

stopped imminently.

Change the USB device or delete a video le.

The camera is not functional, the

Camera

unavailable

message appears.

Have the camera checked in a Mercedes-Benz

service centre.

If the country border indication has been

switched on (/ page 571).

If an outdoor recording is started with the

camera app during a dashcam recording, the

dashcam recording pauses and resumes auto-

matically aer the camera recording is n-

ished. A notication to this eect is displayed.

▌Conguring dashcam settings

Requirements:

A USB device is connected with the multime-

dia system (/ page 620).

Multimedia system:

Apps

Dashcam

Select Z.

Receiving notications aer passing a border

crossing

Switch on National border alert .

A message is shown if video is being recorded

and the vehicle passes a border.

This function is not available in all countries.

Starting automatic video recording

Select Automatic loop recording.

Switch on Automatic loop recording.

When the vehicle is started, video recording

starts automatically.

This function is not available in all countries.

MBUX multimedia system

571

F167 0057 02

MBUX multimedia system -> Navigation and traffic for Your Mercedes GLE SUV Fourth Generation (2020-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals