2017-2024 Mg Zs SUV Instruments and Controls User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Instruments and Controls for Your Mg Zs SUV First Generation (2017-2024)

1
Instruments and Controls  
8
Instruments and Controls  
62 Power Socket  
64 Storage Devices  
67 Cup Holder  
10 Instrument Pack  
13 Information Centre  
29 Warning Lights and Indicators  
37 Lights and Switches  
43 Wipers and Washers  
47 Steering System  
49 Horn  
*
68 Roof Luggage Rack  
50 Mirrors  
53 Sunvisor  
54 Windows  
*
56 Sunroof  
61 Interior Lights  
INSTRUMENTS AND CONTROLS  
Instruments and Controls  
8
INSTRUMENTS AND CONTROLS  
*
1
2
Power Window Switch  
17 START/STOP Switch (Key Start)  
1
Exterior Rearview Mirror and Headlamp Leveling  
Switch  
18 Bonnet Release Handle  
19 Fuel Filler Flap Release Handle  
3
4
5
6
7
8
9
Wiper Stalk Switch  
Horn Button  
Driver Airbag  
Instrument Pack  
Cruise Control/ASL Stalk Switch  
Indicator/Main Beam Stalk Switch  
START/STOP Switch (Keyless Start) *  
10 Infotainment System  
11 Front Passenger Airbag  
12 Infotainment/Air Conditioning Control Switch  
13 Gear Shift Lever  
*
14 Clutch Pedal  
15 Brake Pedal  
16 Accelerator Pedal  
9
INSTRUMENTS AND CONTROLS  
Instrument Pack  
IMPORTANT  
To protect the engine from damage, never allow the  
pointer to remain in the red sector of the gauge for  
prolonged periods.  
Instrument Pack - Colour Display A *  
Engine Coolant Temperature Gauge (3)  
Indicates the engine coolant temperature.  
Fuel Gauge (4)  
Indicates the quantity of fuel in the tank.  
The low fuel warning lamp will illuminate yellow or flash  
when the fuel remaining in the fuel tank is low.  
IMPORTANT  
If the low fuel warning lamp illuminates, please refuel as  
early as possible.  
Speedometer (1)  
Indicates the vehicle speed in mph and km/h.  
Indicates that the fuel filler is located on the  
right side of the vehicle.  
Tachometer (2)  
Indicates the engine speed, ×1000 rpm.  
10  
INSTRUMENTS AND CONTROLS  
Instrument Pack - Colour Display B *  
IMPORTANT  
1
To protect the engine from damage, never allow the  
pointer to remain in the red sector of the gauge for  
prolonged periods.  
Engine Coolant Temperature Gauge (3)  
Indicates the engine coolant temperature.  
Fuel Gauge (4)  
Indicates the quantity of fuel in the tank.  
The low fuel warning lamp will illuminate yellow or flash  
when the fuel remaining in the fuel tank is low.  
IMPORTANT  
Speedometer (1)  
If the low fuel warning lamp illuminates, please refuel as  
early as possible.  
Indicates the vehicle speed in mph and km/h.  
Tachometer (2)  
Indicates that the fuel filler is located on the  
right side of the vehicle.  
Indicates the engine speed, ×1000 rpm.  
11  
INSTRUMENTS AND CONTROLS  
Note: Depending on the vehicle options, software  
version and market area, the information displayed  
may vary slightly.  
Note:  
The units can be changed using the  
entertainment system. Please use the operation steps:  
Setup – Display - Units  
12  
INSTRUMENTS AND CONTROLS  
Information Centre  
4
General Information  
1
Information Centre - Colour Display A *  
Range To Empty  
Displays the estimated mileage that the vehicle can travel  
before the fuel gauge reads empty.  
Gear Display and Gear Shift Indication  
Displays the current gear position of the transmission (P  
*、R *、N *、D *、S *、1、2、3、4、5、6 *). When an  
arrow is displayed to the right of the gear position indicator,  
it advises the driver to shift gear when the conditions  
permit. If "EP" is displayed, it indicates that a fault has  
been detected with the transmission. Please seek an MG  
Authorised Repairer as soon as possible. Refer to "Starting  
& Driving" section.  
Total Mileage  
The information centre provides the followings:  
Displays the total driving mileage of the vehicle.  
1
2
3
Range To Empty  
General Information  
Gear Display and Gear Shift Indication  
Total Mileage  
The general information function can be selected as  
follows:  
13  
INSTRUMENTS AND CONTROLS  
•
•
•
Press the UP/DOWN/LEFT/RIGHT button on the right  
hand multifunction steering wheel switch to shift the  
display items.  
General information provides the following:  
Press the UP/DOWN button on the right hand  
multifunction steering wheel switch to make  
adjustment.  
Press the OK button on the right hand multifunction  
steering wheel switch to confirm or long press OK  
button to reset.  
1
2
3
Warning Information  
Trip Computer  
Setting  
Warning Information  
Displays the warning information or important notes that  
are currently relevant to the vehicle.  
Trip Computer  
Trip computer functions contain the following:  
•
Default Page: displays the current status of the locks,  
lights and doors.  
•
Current Journey: displays the range, duration, average  
speed and average fuel consumption since startup.  
14  
INSTRUMENTS AND CONTROLS  
These values will be reset after a period of power off.  
It can also be reset by long pressing the OK button on  
the right hand multifunction steering wheel switch.  
Accumulated Total: displays the range, duration,  
average speed and average fuel consumption since the  
last reset. It can be reset by long pressing the OK  
button on the right hand multifunction steering wheel  
switch.  
Next Service  
1
Displays and facilitates the reset of the current vehicle  
maintenance information.  
•
Warning Message  
Warning messages and prompts are displayed in the  
information centre in the instrument pack.  
communications are displayed in 'pop up' messages, these  
can be divided into the following categories:  
Any  
•
•
Tyre Pressures: displays the current tyre pressure data  
for each wheel.  
•
•
•
Operating Instruction  
System State Instruction  
System Malfunction Alert  
Battery Voltage: displays the 12V Battery Voltage.  
Setting  
Please follow the instructions displayed in the 'pop up'  
message or in the case of a warning message, please refer  
to the relevant section of the owners manual to follow the  
correct instructions.  
Brightness  
Displays the current level and allows adjustment of the  
backlight brightness.  
Speed Warning  
The following are a selection of warning messages that may  
appear in the information centre.  
Allows the setting of the over-speed alarm threshold.  
15  
INSTRUMENTS AND CONTROLS  
Warning Message  
Procedure  
Warning Message  
Low Oil Pressure  
Procedure  
Indicates that the cruise control  
system has detected a fault.  
Please consult an MG Authorised  
Repairer as soon as possible.  
Indicates that the active speed  
limit system has detected a fault.  
Contact an MG Authorised  
Repairer as soon as possible.  
Indicates that the oil pressure  
is too low, which may result in  
severe engine damage. As soon  
as safety permits, stop the car,  
switch off the engine and check  
the engine oil level. Contact an  
MG Authorised Repairer as soon  
as possible.  
Cruise Control  
Fault  
Active Speed  
Limiter Fault  
High engine coolant temperature  
could result in severe damage.  
As soon as conditions permit,  
Indicates that a failure has  
occurred that will effect engine  
performance and emissions.  
Contact an MG Authorised  
Repairer as soon as possible.  
Engine Coolant  
Engine Fault  
Temperature High safely stop the vehicle and switch  
off the engine and contact an MG  
Authorised Repairer immediately.  
Indicates that a failure has  
occurred that may severely  
damage the engine. As soon as  
conditions permit, safely stop the  
vehicle , switch off the engine  
and contact an MG Authorised  
Repairer immediately.  
Indicates that the engine coolant  
temperature sensor has failed.  
Engine Coolant  
As soon as conditions permit,  
Temperature  
Check Engine  
safely stop the vehicle and switch  
Sensor Fault  
off the engine and contact an MG  
Authorised Repairer immediately.  
16  
INSTRUMENTS AND CONTROLS  
Warning Message  
Procedure  
Warning Message  
Procedure  
1
Indicates that the Stop/Start  
intelligent fuel saving system has  
detected a fault. Please consult  
an MG Authorised Repairer as  
soon as possible.  
Indicates that the Start Stop  
Start Stop Button button has detected a fault.  
Stop Start System  
Fault  
Fault  
Please consult an MG Authorised  
Repairer immediately.  
Indicates that the passive  
Indicates that the clutch switch  
has detected a fault. Please  
consult an MG Authorised  
Repairer as soon as possible.  
keyless entry (PKE) function has  
Passive Entry Fault detected a fault. Please consult  
an MG Authorised Repairer as  
soon as possible.  
Clutch Switch Fault  
Indicates that the gasoline  
Gasoline Particular particular filter is full. Please  
Indicates that the anti-lock  
brake system (ABS) has failed  
Filter Full  
consult an MG Authorised  
Repairer as soon as possible.  
and the ABS function is about  
to be disabled. Please consult  
ABS Fault  
an MG Authorised Repairer  
immediately.  
Indicates that the ignition system  
has detected a fault. Please  
consult an MG Authorised  
Repairer immediately.  
Ignition System  
Fault  
17  
INSTRUMENTS AND CONTROLS  
Warning Message  
Procedure  
Warning Message  
EPB System Fault  
Procedure  
Indicates that the brake fluid  
could be low or a fault has  
been detected in the Electronic  
Brake-force Distribution (EBD)  
system. As soon as safety  
permits, stop the car, switch  
off the engine and check the  
brake fluid level. Contact an MG  
Authorised Repairer as soon as  
possible.  
Indicates that the electronic  
parking brake system (EPB) has  
detected a fault. Please consult  
an MG Authorised Repairer as  
soon as possible.  
Brake Fault  
Indicates that there is an issue  
with the electronic parking  
Park Brake Force brake, it may not be able to  
Not Enough  
provide adequate clamping force.  
Contact an MG Authorised  
Repairer as soon as possible.  
Indicates that the stability control  
system has detected a fault.  
Please consult an MG Authorised  
Repairer immediately.  
Stability Control  
Fault  
Indicates that the Autohold  
System has detected a fault.  
Please consult an MG Authorised  
Repairer as soon as possible.  
Autohold Fault  
Indicates that the traction  
Traction Control  
Fault  
control system has detected  
a fault. Please consult an MG  
Authorised Repairer immediately.  
Indicates that the hill descent  
control system has detected  
a fault. Please consult an MG  
Authorised Repairer as soon as  
possible.  
Hill Descent  
Control Fault  
18  
INSTRUMENTS AND CONTROLS  
Warning Message  
Procedure  
Warning Message  
Procedure  
1
Indicates that the electric power  
steering system has a general  
failure and that the steering  
performance has been reduced.  
As soon as conditions permit,  
safely stop the vehicle and switch  
off the engine. After a short  
while, start the engine, drive  
the vehicle a short distance  
and monitor the operation of  
the steering, if the message is  
still displayed or the steering  
assistance reduced please  
Indicates that the steering angle  
sensor has failed. Please consult  
an MG Authorised Repairer as  
soon as possible.  
Steering Angle Fault  
Indicates that the steering angle  
sensor is not calibrated. Please  
consult an MG Authorised  
Repairer as soon as possible.  
Steering Angle  
Uncalibrated  
EPS Performance  
Reduced  
Indicates that a fault has been  
detected with the Electronic  
Steering Column Lock (ESCL).  
As soon as conditions permit,  
safely stop the vehicle and switch  
off the engine. Contact an MG  
Authorised Repairer as soon as  
possible.  
ESCL Fault  
contact an MG Authorised  
Repairer immediately.  
Indicates that the electric power  
steering system has failed. Please  
consult an MG Authorised  
Repairer immediately.  
EPS Assistance  
Failure  
Indicates that fuel sensor has  
detected a fault. Please consult  
an MG Authorised Repairer as  
soon as possible.  
Fuel Sensor Fault  
19  
INSTRUMENTS AND CONTROLS  
Warning Message  
Procedure  
Warning Message  
Procedure  
Indicates that the Airbag system  
has detected a fault. As soon as  
conditions permit, safely stop the  
vehicle and switch off the engine  
and contact an MG Authorised  
Repairer immediately.  
Indicates that the 12V battery  
charging system has failed. Please  
consult an MG Authorised  
Repairer immediately.  
12V Battery  
Charging System  
Fault  
Airbag Fault  
Indicates that the rear drive  
assist system (RDA) has detected  
a fault. Please consult an MG  
Authorised Repairer as soon as  
possible.  
Rear Drive Assist  
System Fault  
Indicates that the Tyre Pressure  
Monitoring system has detected  
that a tyre pressure sensor has  
a low battery. Please consult an  
MG Authorised Repairer as soon  
as possible.  
Front Left/Front  
Right/Rear  
Left/Rear Right  
Tyre Sensor Battery  
Low  
Indicates that the tyre pressure  
monitoring system has detected  
a fault. Please consult an MG  
Authorised Repairer as soon as  
possible.  
TPMS Fault  
20  
INSTRUMENTS AND CONTROLS  
Information Centre - Colour Display B *  
Digital Clock  
1
Displays the current time in digital form.  
Gear Display and Gear Shift Indication  
Displays the current gear position of the transmission (P  
*、R *、N *、D *、S *、1、2、3、4、5、6 *). When an  
arrow is displayed to the right of the gear position indicator,  
it advises the driver to shift gear when the conditions  
permit. If "EP" is displayed, it indicates that a fault has  
been detected with the transmission. Please seek an MG  
Authorised Repairer as soon as possible. Refer to "Starting  
& Driving" section.  
Total Mileage  
Displays the total driving mileage of the vehicle.  
1
2
3
4
Digital Clock  
Gear Display and Gear Shift Indication  
Total Mileage  
General Information  
The general information function can be selected as  
follows:  
General Information  
•
Press the UP/DOWN/LEFT/RIGHT button on the right  
hand multifunction steering wheel switch to shift the  
display items.  
21  
INSTRUMENTS AND CONTROLS  
•
Press the UP/DOWN button on the right hand  
multifunction steering wheel switch to make  
adjustment.  
•
Press the OK button on the right hand multifunction  
steering wheel switch to confirm or long press OK  
button to reset.  
1
2
3
Trip Computer  
Setting  
Warning Information  
Trip Computer  
Trip computer functions contain the following:  
•
Current Speed: displays the current vehicle speed in a  
digital form.  
•
Range to Empty: displays the range that the vehicle can  
travel before the fuel tank is empty, the value of the  
range will change after refueling.  
•
Current Journey: displays the range, duration, average  
speed and average fuel consumption since startup.  
These values will be reset after a period of power off.  
It can also be reset by long pressing the OK button on  
the right hand multifunction steering wheel switch.  
General information provides the following:  
22  
INSTRUMENTS AND CONTROLS  
•
•
Accumulated Total: displays the range, duration,  
average speed and average fuel consumption since the  
last reset. It can be reset by long pressing the OK  
button on the right hand multifunction steering wheel  
switch.  
Next Service  
1
Displays and facilitates the reset of the current vehicle  
maintenance information.  
Warning Information  
Instantaneous Fuel Economy: displays the current fuel  
consumption when the engine is working.  
Battery Voltage: displays the 12V Battery Voltage.  
Tyre Pressures: displays the current tyre pressure data  
for each wheel.  
Displays the warning information or important notes that  
are currently relevant to the vehicle.  
•
•
Warning Message  
Warning messages and prompts are displayed in the  
Setting  
information centre in the instrument pack.  
Any  
communications are displayed in 'pop up' messages, these  
can be divided into the following categories:  
Brightness  
Displays the current level and allows adjustment of the  
backlight brightness.  
•
•
•
Operating Instruction  
System State Instruction  
System Malfunction Alert  
Note: This option can only be adjusted when the side  
lamps are on.  
Please follow the instructions displayed in the 'pop up'  
message or in the case of a warning message, please refer  
to the relevant section of the owners manual to follow the  
correct instructions.  
Speed Warning  
Allows the setting of the over-speed alarm threshold.  
23  
INSTRUMENTS AND CONTROLS  
The following are a selection of warning messages that may  
appear in the information centre.  
Warning Message  
Procedure  
Indicates that the engine coolant  
temperature sensor has failed.  
As soon as conditions permit,  
safely stop the vehicle and switch  
off the engine and contact an MG  
Authorised Repairer immediately.  
Warning Message  
Procedure  
Engine Coolant  
Temperature  
Sensor Fault  
Indicates that the cruise control  
system has detected a fault.  
Please consult an MG Authorised  
Repairer as soon as possible.  
Cruise Control  
Fault  
Indicates that the oil pressure  
is too low, which may result in  
severe engine damage. As soon  
as safety permits, stop the car,  
switch off the engine and check  
the engine oil level. Contact an  
MG Authorised Repairer as soon  
as possible.  
Indicates that the active speed  
limit system has detected a fault.  
Contact an MG Authorised  
Repairer as soon as possible.  
Active Speed  
Limiter Fault  
Low Oil Pressure  
High engine coolant temperature  
could result in severe damage.  
As soon as conditions permit,  
Engine Coolant  
Temperature High safely stop the vehicle and switch  
off the engine and contact an MG  
Indicates that a failure has  
occurred that will effect engine  
performance and emissions.  
Contact an MG Authorised  
Repairer as soon as possible.  
Authorised Repairer immediately.  
Engine Fault  
24  
INSTRUMENTS AND CONTROLS  
Warning Message  
Check Engine  
Procedure  
Warning Message  
Procedure  
1
Indicates that a failure has  
occurred that may severely  
damage the engine. As soon as  
conditions permit, safely stop  
the vehicle, switch off the engine  
and contact an MG Authorised  
Repairer immediately.  
Indicates that the ignition system  
has detected a fault. Please  
consult an MG Authorised  
Repairer immediately.  
Ignition System  
Fault  
Indicates that the Start Stop  
Start Stop Button button has detected a fault.  
Fault  
Please consult an MG Authorised  
Repairer immediately.  
Indicates that the Stop/Start  
intelligent fuel saving system has  
detected a fault. Please consult  
an MG Authorised Repairer as  
soon as possible.  
Indicates that the passive  
keyless entry (PKE) function has  
Stop Start System  
Fault  
Passive Entry Fault detected a fault. Please consult  
an MG Authorised Repairer as  
soon as possible.  
Indicates that the clutch switch  
has detected a fault. Please  
consult an MG Authorised  
Repairer as soon as possible.  
Indicates that the anti-lock  
brake system (ABS) has failed  
and the ABS function is about  
Clutch Switch Fault  
ABS Fault  
Indicates that the gasoline  
to be disabled. Please consult  
Gasoline Particular particular filter is full. Please  
an MG Authorised Repairer  
immediately.  
Filter Full  
consult an MG Authorised  
Repairer as soon as possible.  
25  
INSTRUMENTS AND CONTROLS  
Warning Message  
Procedure  
Warning Message  
EPB System Fault  
Procedure  
Indicates that the brake fluid  
could be low or a fault has  
been detected in the Electronic  
Brake-force Distribution (EBD)  
system. As soon as safety  
permits, stop the car, switch  
off the engine and check the  
brake fluid level. Contact an MG  
Authorised Repairer as soon as  
possible.  
Indicates that the electronic  
parking brake system (EPB) has  
detected a fault. Please consult  
an MG Authorised Repairer as  
soon as possible.  
Brake Fault  
Indicates that there is an issue  
with the electronic parking  
Park Brake Force brake, it may not be able to  
Not Enough  
provide adequate clamping force.  
Contact an MG Authorised  
Repairer as soon as possible.  
Indicates that the stability control  
system has detected a fault.  
Please consult an MG Authorised  
Repairer immediately.  
Stability Control  
Fault  
Indicates that the Autohold  
System has detected a fault.  
Please consult an MG Authorised  
Repairer as soon as possible.  
Autohold Fault  
Indicates that the traction  
Traction Control  
Fault  
control system has detected  
a fault. Please consult an MG  
Authorised Repairer immediately.  
Indicates that the hill descent  
control system has detected  
a fault. Please consult an MG  
Authorised Repairer as soon as  
possible.  
Hill Descent  
Control Fault  
26  
INSTRUMENTS AND CONTROLS  
Warning Message  
Procedure  
Warning Message  
Procedure  
1
Indicates that the electric power  
steering system has a general  
failure and that the steering  
performance has been reduced.  
As soon as conditions permit,  
safely stop the vehicle and switch  
off the engine. After a short  
while, start the engine, drive  
the vehicle a short distance  
and monitor the operation of  
the steering, if the message is  
still displayed or the steering  
assistance reduced please  
Indicates that the steering angle  
sensor has failed. Please consult  
an MG Authorised Repairer as  
soon as possible.  
Steering Angle Fault  
Indicates that the steering angle  
sensor is not calibrated. Please  
consult an MG Authorised  
Repairer as soon as possible.  
Steering Angle  
Uncalibrated  
EPS Performance  
Reduced  
Indicates that a fault has been  
detected with the Electronic  
Steering Column Lock (ESCL).  
As soon as conditions permit,  
safely stop the vehicle and switch  
off the engine. Contact an MG  
Authorised Repairer as soon as  
possible.  
ESCL Fault  
contact an MG Authorised  
Repairer immediately.  
Indicates that the electric power  
steering system has failed. Please  
consult an MG Authorised  
Repairer immediately.  
EPS Assistance  
Failure  
Indicates that fuel sensor has  
detected a fault. Please consult  
an MG Authorised Repairer as  
soon as possible.  
Fuel Sensor Fault  
27  
INSTRUMENTS AND CONTROLS  
Warning Message  
Procedure  
Warning Message  
TPMS Fault  
Procedure  
Indicates that the Airbag system  
has detected a fault. As soon as  
conditions permit, safely stop  
the vehicle, switch off the engine  
and contact an MG Authorised  
Repairer immediately.  
Indicates that the tyre pressure  
monitoring system has detected  
a fault. Please consult an MG  
Authorised Repairer as soon as  
possible.  
Airbag Fault  
Indicates that the 12V battery  
charging system has failed. Please  
consult an MG Authorised  
Repairer immediately.  
12V Battery  
Charging System  
Fault  
It indicates that the airbag lamp  
has failed. Please consult an MG  
Authorised Repairer as soon as  
possible.  
Airbag Lamp Fail  
Indicates that the Tyre Pressure  
Monitoring system has detected  
that a tyre pressure sensor has  
a low battery. Please consult an  
MG Authorised Repairer as soon  
as possible.  
Front Left/Front  
Right/Rear  
Left/Rear Right  
Tyre Sensor Battery  
Low  
28  
INSTRUMENTS AND CONTROLS  
Warning Lights and Indicators  
Rear Fog Lamp Indicator - Yellow  
1
Some warning lamps illuminate or flash accompanied by a  
warning tone.  
The indicator illuminates when the rear fog  
lamps are on.  
High Beam Indicator - Blue  
Front Fog Lamp Indicator - Green *  
The indicator illuminates when the headlamp  
high beam is turned on.  
The indicator illuminates when the front fog  
lamps are on.  
Side Lamp Indicator - Green  
Direction Indicator Lamp - Green  
The indicator illuminates when the side lamps  
are on.  
The left and right direction indicator lamps are  
represented by directional arrows that are located at the  
top of the instrument pack. When the turning signal lamp  
flashes, the direction indicator lamp on the corresponding  
side also flashes. If the hazard warning lamps are operated,  
both direction indicator lamps will flash together. If either  
direction indicator lamp in the instrument pack flashes  
very rapidly, it indicates that the turning signal light on the  
corresponding side has failed.  
On some models, if the side lamps are switched ON  
and the driver opens the door, this indicator will flash  
accompanied by an audible warning chime reminding the  
driver to switch the side lamps OFF.  
29  
INSTRUMENTS AND CONTROLS  
Note: Failure of a side repeater lamp will have no  
effect on the flash frequency of direction indicator  
lamp.  
Seat Belt Unfastened Warning Lamp - Red  
If this lamp illuminates or flashes, it indicates  
that the seat belt for the driver or front passenger remains  
unfastened.  
Anti-theft System Warning Lamp - Red  
If no valid key is detected, this lamp illuminates  
red. Please use the correct key, or put the smart key at  
the bottom of the centre console cup holder. For specific  
location requirements, refer to “Alternative Starting  
Procedure” in “Starting & Driving” section.  
This vehicle is equipped with rear seat belt  
warnings to remind you to ensure any rear seat passengers  
have fastened their seat belts. The dedicated warning lamp  
consists of the 3 sections, 1 for each rear seat position,  
it will illuminate red on every ignition cycle and remain  
illuminated until a pre-set speed is reached and after a  
pre-set time period. If all 3 rear seat belts are fastened  
this lamp will extinguish immediately. When each individual  
rear seat belt is fastened the colour of that particular seat  
belt warning lamp will change from red to grey, the other  
seat positions will remain illuminated red, all 3 seat belt  
warning lamps will extinguish after the pre-set speed is  
reached and the pre-set time has been surpassed.  
If the remote key battery is low, this lamp will flash. Please  
replace the battery as soon as possible.  
Airbag Warning Lamp - Red  
If this lamp illuminates, it indicates that there  
is a failure in the SRS or seat belt. Please seek an MG  
Authorised Repairer at the earliest opportunity. An SRS  
or seat belt fault may mean the components may not be  
deployed in the event of an accident.  
30  
INSTRUMENTS AND CONTROLS  
Engine Malfunction Warning - Yellow  
High engine coolant temperature could result in severe  
damage. Please stop the car as soon as safety permits,  
switch the engine OFF and contact an MG Authorised  
Repairer immediately.  
1
This lamp will illuminate if an engine fault occurs  
that will effect engine performance during driving. Please  
stop the car as soon as safety permits, switch the engine  
OFF and contact an MG Authorised Repairer immediately.  
Low Oil Pressure Warning - Red  
If this lamp illuminates after starting the vehicle,  
it indicates that the oil pressure is too low, which may  
result in severe engine damage. Please stop the car as  
soon as safety permits, switch the engine OFF and check oil  
level (refer to "Engine Oil Level Check and Top Up" under  
the "Maintenance"). Contact an MG Authorised Repairer  
immediately.  
Engine Emissions Malfunction Warning - Yellow  
If an engine fault occurs that will effect engine  
performance and emission after starting the vehicle, this  
lamp will illuminate. Please contact an MG Authorised  
Repairer as soon as possible.  
Engine Coolant Temperature Warning - Red  
Alternator Malfunction Warning - Red  
When the engine coolant temperature  
warning lamp illuminates red, it indicates that the coolant  
temperature is high. If the engine coolant temperature  
continues to rise, the engine coolant temperature warning  
lamp will flash.  
If this lamp illuminates after starting the  
vehicle, it indicates that the 12v battery charging system  
has a failure. Please contact an MG Authorised Repairer  
immediately.  
31  
INSTRUMENTS AND CONTROLS  
In cases of low battery power, the prompt messages will  
appear in the information centre. In this case, the system  
will limit or turn off some electrical devices, please start  
the vehicle to charge the battery.  
Cruise Control Indicator - Green/Yellow  
If the cruise control function is enabled, the  
system will enter into the standby state and the indicator  
illuminates in yellow.  
Stop/Start Intelligent Fuel Saving System Status  
Indicator - Green  
When the cruise control system operates, this indicator  
illuminates green, indicating the cruise control system is  
activated.  
If the Stop/Start intelligent fuel saving system is  
activated, this lamp illuminates to inform the driver that  
the engine is controlled by the system. When the system  
is currently unavailable, this lamp flashes three times and  
then extinguishes.  
If a failure in the cruise control system is detected, the  
indicator will flash in yellow. Please contact an MG  
Authorised Repairer as soon as possible.  
Tyre Pressure Monitoring System (TPMS)  
Warning Lamp - Yellow  
Stop/Start Intelligent Fuel Saving System  
Malfunction Warning Lamp - Yellow  
If this lamp illuminates, it indicates a tyre  
pressure is low, please check the tyre pressures.  
If the Stop/Start intelligent fuel saving system  
has a failure, this lamp illuminates. Please contact an MG  
Authorised Repairer as soon as possible.  
If this lamp flashes first and then remains on after a period  
of time, it indicates the system has a failure. Please contact  
an MG Authorised Repairer at the earliest opportunity.  
32  
INSTRUMENTS AND CONTROLS  
Stability Control/Traction Control System  
Warning Lamp - Yellow  
abnormally, but normal braking will still be available. Please  
contact an MG Authorised Repairer as soon as possible.  
1
Brake System Malfunction Indicator Lamp - Red  
If this lamp illuminates, it indicates that the  
stability control/traction control system has a failure.  
Please contact an MG Authorised Repairer immediately.  
If this lamp illuminates, it indicates a failure with  
the braking system such as brake fluid loss or electronic  
brake force distribution failure. Please stop the car as  
soon as safety permits, switch the engine OFF and check  
brake fluid level (refer to "Brake Fluid Check and Top Up"  
under the "Maintenance" section). If the brake fluid level  
appears satisfactory contact an MG Authorised Repairer at  
the earliest opportunity.  
If this lamp flashes during driving, it indicates the system is  
operating to assist the driver.  
Stability Control/Traction Control System Off  
Warning Lamp - Yellow  
For manual parking brake, the lamp illuminates when  
the parking brake is applied and extinguishes when it is  
fully released. If the parking brake is not released, when  
the vehicle speed exceeds 3 mph (5 km/h), this warning  
lamp will flash. If the lamp remains on after the parking  
brake has been released, it indicates that there is a failure  
in the braking system. Please stop the car as soon as  
safety permits, switch the engine OFF and contact an MG  
Authorised Repairer immediately.  
This lamp will illuminate if the dynamic stability  
control/ traction control system is manually switched off.  
ABS Malfunction Warning Lamp - Yellow  
This lamp illuminates to indicate an ABS fault.  
If an ABS failure occurs while driving, ABS will function  
33  
INSTRUMENTS AND CONTROLS  
Electronic Parking Brake (EPB)/Automatic  
Parking Status Indicator Lamp - Red/Green *  
Hill Descent Control (HDC) On/Malfunction  
Indicator Lamp - Green/Yellow  
If this lamp illuminates red, it indicates the  
electronic parking brake is enabled or in the process of  
dynamic braking. When it flashes red, it indicates the  
electronic parking brake has failed. Please contact the MG  
Authorised Repairer at the earliest opportunity.  
Operating the HDC switch will activate the  
function, the system will enter the stand by mode and the  
warning lamp illuminates green, the lamp will extinguish  
when the system is turned off. If the vehicle is under the  
control of HDC the green warning lamp will flash.  
When the auto hold system is operating to assist the driver,  
this lamp illuminates green.  
If the HDC system detects a fault or fails, the warning  
lamp illuminates yellow. Please contact an MG Authorised  
Repairer immediately.  
Electronic Parking Brake (EPB) System  
Malfunction Indicator Lamp - Yellow *  
Electric Power Steering System (EPS)/  
Electronic Steering Column Lock (ESCL)  
*
Warning Lamp - Yellow/Red  
If an electronic parking brake system failure is  
detected or the system is under diagnosis, the indicator  
lamp will illuminate. Please contact an MG Authorised  
Repairer at the earliest opportunity.  
The warning lamp is used to indicate electric  
power assisted steering failure or electronic steering  
column lock failure.  
34  
INSTRUMENTS AND CONTROLS  
When this lamp illuminates yellow, it indicates the electric  
power assisted steering system has a general failure and  
the performance is reduced. Please stop the car as soon as  
safety permits. If the lamp still illuminates after restarting  
the vehicle and driving for a short while, please contact an  
MG Authorised Repairer immediately.  
Low Fuel Warning Lamp - Yellow  
1
The warning lamp illuminates yellow when the  
fuel remaining in the fuel tank is low. If possible, please  
refuel before the low fuel warning lamp illuminates.  
When the fuel level continues to fall, this lamp flashes.  
When fuel is added to the tank and the fuel level rises  
above the alert limit, this lamp extinguishes. If it does not  
extinguish, please contact an MG Authorised Repairer for  
service as soon as possible.  
When this lamp illuminates red, it indicates that the  
EPS has a failure relevant to the steering angle sensor.  
Please contact an MG Authorised Repairer at the earliest  
opportunity.  
When this lamp illuminates red and flashes, it indicates the  
electric power assisted steering system has a severe failure  
and heavy steering. Please contact an MG Authorised  
Repairer immediately.  
Note: When driving on steep or rough roads while the  
fuel level is low, the warning lamp may illuminate.  
System Fault Messages Indicator - Yellow *  
When the lamp illuminates yellow and flashes, it indicates  
the electric steering column lock * has a failure. Please stop  
the car as soon as safety permits, switch the engine OFF  
and contact an MG Authorised Repairer immediately. If  
this lamp extinguishes after flashing for a while, it indicates  
that the steering wheel is locked, please attempt to rotate  
the steering wheel to remove any adverse loads.  
This indicator is used to alert the driver to the  
fact that there is a warning stored in the vehicle IPK system.  
Please refer to "Information Centre" in this section for  
these failures.  
35  
INSTRUMENTS AND CONTROLS  
Active Speed Limit System Warning Lamp —  
Yellow  
Particulate Filter Warning Lamp - Yellow *  
When this lamp illuminates yellow, it indicates  
that the particulate filter requires regeneration. Please  
drive the vehicle above 50mph until the light is no longer  
illuminated, and then normal usage can be resumed.  
This warning lamp illuminates if an active speed  
limit system failure is detected. Please contact an MG  
Authorised Repairer as soon as possible.  
Note: During particulate filter regeneration the  
engine will run unevenly and at reduced power, this  
will cease after a successful regeneration.  
Active Speed Limit System Indicator — Red  
When the active speed limit system is armed  
or active, if the target vehicle speed is currently set, this  
indicator illuminates and displays the target vehicle speed  
value.  
When this lamp flashes, it indicates that the particulate  
filter is full, the engine malfunction indicator lamp  
illuminates at the same time. Please contact an MG  
Authorised Repairer immediately. Please note if the  
warning is ignored, the vehicle will enter a reduced  
performance mode and may subsequently be immobilised.  
When the active speed limit system is working, if the  
current speed exceeds the set target speed, this indicator  
will flash, and the system will immediately reduce the  
speed to below the target speed. The active speed limiter  
only uses engine braking to reduce speed - it is not a  
substitute for physical brake application. If the vehicle  
needs to be slowed or stopped quickly the brake pedal  
MUST be applied.  
Please refer to “Catalytic Converter and Particulate Filter”  
in “Starting & Driving” section.  
36  
INSTRUMENTS AND CONTROLS  
Lights and Switches  
Master Lighting Switch  
AUTO Lamp  
1
When the START/STOP Switch is in the ACC position, the  
auto lighting system defaults to the ON position (1). The  
auto lighting system will automatically switch the side lamps  
and switch illumination on and off according to the intensity  
of current ambient light.  
With the START/STOP Switch switched to the ON  
position, the auto lighting system defaults to the ON  
position (1). The auto lighting system will automatically  
switch the side lamps, switch illumination and dipped  
headlamps on and off according to the intensity of current  
ambient light.  
Note: This function is realized by fitting a sensor  
capable of monitoring exterior lighting conditions  
in real time on your vehicle. The sensor is fitted in  
the centre of the fascia panel near the windscreen  
in some models. DO NOT mask or cover this area,  
or headlamps may automatically go on when not  
necessary.  
1
2
3
4
AUTO Lamp  
Side Lamps and Switch Illumination  
Dipped Headlamps  
Lights OFF  
37  
INSTRUMENTS AND CONTROLS  
Side lamps and Switch Illumination  
headlamps and side lamps will illuminate depending upon  
the vehicle configuration. It can be set in the ‘Comfort and  
Convenience’ in the Vehicle Settings on the entertainment  
display.  
Turn the master lighting switch to position 2 to operate the  
side lamps and switch illumination. With the START/STOP  
Switch in the OFF position if the lighting switch is in  
position 2 and the driver’s door opened an audible warning  
will sound to alert the driver, the side lamps will remain  
on.  
Daytime Running Lamp  
The daytime running lamps turn on automatically when  
the START/STOP Switch is in the ON position. When  
the side lamps are switched on, the daytime running lamps  
extinguish automatically.  
Dipped Headlamps  
When the START/STOP Switch is in the ON position, turn  
the master lighting switch to position 3 to operate the  
dipped headlamps and side lamps.  
Find My Car  
After the vehicle has been left in a locked condition for a  
few minutes pressing the lock button again on the remote  
key will enable the Find My Car function. This function  
will identify the car by means of an audible and visual alert.  
Pressing the Lock button on the handset again will suspend  
this operation. Pressing the Unlock button will cancel  
this operation. This feature can be set via ‘Comfort and  
Convenience’ in the Vehicle Settings on the entertainment  
display.  
Lights Off  
Turn the master lighting switch to position 4, this will  
switch off all lamps, releasing the switch will allow it to  
return to the AUTO switch position.  
Follow Me Home  
After the START/STOP Switch is turned off, pull the  
lighting stalk switch towards the steering wheel. This  
will enable the Follow Me Home function, dipped beam  
38  
INSTRUMENTS AND CONTROLS  
Headlamp Levelling Manual Adjustment  
Location  
Load  
1
0
1
Driver, or driver & front passenger.  
All the seats occupied with no load.  
All the seats occupied plus an evenly  
distributed load in the boot, or driver with  
full load.  
2
3
Driver only, plus an evenly distributed load in  
the boot.  
Position 0 is the initial position of the headlamp levelling  
adjustment switch. The headlamp levelling adjustment can  
be made as per the following table according to the vehicle  
load.  
39  
INSTRUMENTS AND CONTROLS  
Fog Lamp Switch  
will turn on the front fog lamps. The indicator illuminates  
in the instrument panel when the front fog lamps are on.  
Fog lights should only be used when visibility  
is below 100m - other road users could be  
dazzled in clear conditions.  
Rear Fog Lamp  
With the START/STOP Switch in the ON position and the  
headlamps or front fog lamps on, turn the fog lamp switch  
to position 2, this will turn on the rear fog lamp, release  
the switch to allow it to return to the last position. The  
indicator illuminates in the instrument panel when the rear  
fog lamp is on.  
*
Front Fog Lamps  
With the START/STOP Switch in the ON position and the  
side lamps on, turn the fog lamp switch to position 1, this  
40  
INSTRUMENTS AND CONTROLS  
Direction Indicator/Main Beam Switch  
GREEN indicator lamp in the instrument pack will flash  
when the turning signal lamps are working.  
1
Take care not to dazzle oncoming vehicles  
when driving using main beam headlamps.  
Rotating the steering wheel will cancel the indicator  
operation (small movements of the steering wheel may  
not operate the self cancelling). To indicate a lane change,  
move the lever briefly and release, the indicators will flash  
three times and then cancel.  
Headlamp High/Low Beam Switching  
With the START/STOP Switch in the ON position and the  
master lighting switch turned to position 3, or the auto  
function has switched the lights on, push the lever (3)  
towards the instrument panel to turn on headlamp high  
beams. The high beam indicator lamp in instrument pack  
illuminates, press the lever (3) again to switch to headlamp  
low beams.  
High Beam Flash  
Direction Indicators  
To briefly flash the high beam on and off, pull the lever  
towards the steering wheel (4) and then release.  
Move the lever down to indicate a LEFT turn (1). Move the  
lever up to indicate a RIGHT turn (2). The corresponding  
41  
INSTRUMENTS AND CONTROLS  
Hazard Warning Lamp  
Press the hazard warning lamp button  
to turn on  
the hazard warning lamps. The turning signal lamps and  
direction indicator lamps will flash together. Press the  
button again to switch off the hazard warning lamps. All  
turning signal lamps and direction indicator lamps will stop  
flashing. For more details and location refer to 'Emergency  
Information' 'Hazard Warning Devices'.  
42  
INSTRUMENTS AND CONTROLS  
Wipers and Washers  
•
•
•
Fast wipe (3)  
1
Single wipe (4)  
*
Automatic wipe interval adjustment / Rain sensor  
sensitivity adjustment (5)  
*
•
Programmed wash/wipe (6)  
Intermittent Wipe  
By pushing the lever up to the Intermittent wipe position  
(1), the wipers will operate automatically. Turn the switch  
(5) * to adjust the intermittent wipe frequency. This speed  
will also change with the vehicle speed. As the vehicle  
speed increases, the wiper frequency increases. As the  
vehicle speed decreases, the wiper frequency decreases.  
Some models are equipped with a rain sensor fitted to the  
interior rear view mirror base to detect varying amounts  
of water on the outside of the windscreen. With automatic  
wipe, the vehicle will adjust the wiping speed according to  
the signals provided by rain sensor. Turn the switch (5)  
to adjust the sensitivity of rain sensor. As the sensitivity  
increases, the wiping interval decreases.  
Windscreen Wiper Operation  
The wipers and washers will only operate with the  
START/STOP Switch in the ACC/ON/RUNNING position.  
Operate the lever to select different wipe speeds:  
Note: Immediately operating the wiper one time can  
be achieved by increasing the sensitivity of rain sensor.  
•
•
Intermittent wipe (1)  
Slow wipe (2)  
43  
INSTRUMENTS AND CONTROLS  
If the rain sensor detects a continuous rainwater, the  
wiper will keep working. When no rain is detected, it  
is recommended to switch off automatic wipe.  
IMPORTANT  
•
•
Avoid operating the wiper on a dry windscreen.  
In freezing or extremely hot weather conditions,  
make sure that the wiper blades are not  
frozen/adhered to the windscreen.  
Slow Wipe  
By pushing the lever up to the slow wipe position (2), the  
wipers will operate slowly. Move the lever to re-select the  
wipe speed.  
•
In winter, remove snow or ice from around the arms  
and blades, including the wiped area of the screen.  
Fast Wipe  
Programmed Wash/Wipe  
By pushing the lever up to the fast wipe position (3), the  
wipers will operate fast. Move the lever to re-select the  
wipe speed.  
Pulling the lever toward the steering wheel (6) will operate  
the windscreen washers. After a short delay, the wipers  
will commence operating in conjunction with the washers.  
Note: The wipers continue operating for a further  
three wipes after the lever is released. After several  
seconds, there will be a further wipe to remove any  
fluid draining down the screen.  
Single Wipe  
Pressing the lever (4) down and releasing will operate  
a single wipe, if the lever is held down, the wipers will  
operate until the lever is released.  
Note: When the car is stationary, if the bonnet  
is opened, the front wiper/washer will stop work  
immediately.  
44  
INSTRUMENTS AND CONTROLS  
Rear Window Wiper Operation  
IMPORTANT  
1
If the washers fail to deliver the screen wash solution  
(dirt or ice may have blocked the jets), release the  
lever immediately.  
This will prevent the wipers  
from operating, and the consequent risk of visibility  
being impaired by dirt smearing across the unwashed  
windscreen.  
•
•
•
•
Intermittent wipe (1)  
Wash and wipe (2)  
Wash and wipe (3)  
Intermittent wipe frequency adjustment (4)  
The rear window wiper and washer will only operate  
with the START/STOP Switch in the ACC/ON/RUNNING  
position.  
Turn the rear window wiper switch to  
intermittent wipe (1), the rear window wiper will operate,  
45  
INSTRUMENTS AND CONTROLS  
after 3 consecutive wipes, the wipers will enter into  
intermittent mode. The time period between the wipes  
can be increased/decreased via the intermittent wipe  
frequency adjustment switch (4).  
Note: When the windscreen wipers are switched on, if  
the shift control lever is moved to, or in the R position,  
the rear window wiper will operate.  
Turn the rear window wiper switch to wash and wipe (2)  
position and hold, the rear window wiper and washer will  
operate, the rear window wiper wipes quickly. release the  
switch allowing it to return to intermittent wipe (1), the  
rear window washer will stop operating, and the wiper  
wipes slowly, change the stalk switch position 4 to adjust  
the wipe speed.  
Turn the rear window wiper switch to wash and wipe (3)  
and hold, the rear window wiper and washer will operate.  
release the switch allowing it to return to OFF position,  
the rear window washer will stop operating, and the rear  
window wiper wipes for 3 times, after several seconds, the  
wiper will wipe once more to remove the washer fluid on  
the windscreen.  
Note: When the tailgate is opened, rear window wiper  
operations will be disabled.  
46  
INSTRUMENTS AND CONTROLS  
Steering System  
To adjust the angle of the steering column to suit your  
driving position:  
1
Adjustment of Steering Column  
1
Fully release the locking lever.  
DO NOT attempt to adjust the angle of  
the steering column while the vehicle is in  
motion. This is extremely dangerous.  
2
Hold the steering wheel in both hands and tilt the  
steering column up or down to move the wheel into  
the most comfortable position.  
3
Once a comfortable driving position has been selected,  
pull the locking lever fully up to lock the steering  
column into its new position.  
47  
INSTRUMENTS AND CONTROLS  
Electric Power Steering  
Steering Mode Switching  
The electric power steering system provides 3 different  
steering modes:  
If the electric power steering fails or cannot  
operate the steering will appear very heavy,  
this will affect driving safety.  
1
Normal: provides moderate power assistance.  
2
Urban: provides a high level of assistance, with a light  
feel.  
The electric power steering system only works when the  
vehicle is started. The system operates via a motor with  
assistance levels automatically adjusted based on vehicle  
speed, steering wheel torque and steering wheel angle.  
3
Dynamic: provides low level power assistance, with a  
heavier feel.  
The steering mode is selectable for vehicle speeds up to 60  
mph (100 km/h) through the touch screen interface.  
IMPORTANT  
Holding the steering wheel on full lock for long periods  
will result in a reduction in power assistance causing a  
heavier feel to the steering for a short period of time.  
Note: Steering mode selection is only available when  
the steering wheel is not being turned. Any changes  
made in this state will not take effect until the steering  
wheel is straight ahead.  
Electric Power Steering (EPS) Warning Lamp  
See "Warning Lamps and Indicators" under the  
"Instruments and Controls" section.  
48  
INSTRUMENTS AND CONTROLS  
Horn  
avoid any potential conflict with the operation of the  
airbag.  
1
IMPORTANT  
To avoid possible SRS issues, please do not press with  
excessive force or hit the airbag cover when operating  
the horn.  
Press the horn button area on the steering wheel (as  
indicated by the arrow) to operate the horn.  
Note: The vehicle horn switch location and the driver's  
airbag are located in close proximity on the steering  
wheel. The illustration shows the position of the horn  
switches, please ensure that you press in this area to  
49  
INSTRUMENTS AND CONTROLS  
Mirrors  
•
The mirror adjustment function will work with the  
power system in all modes, including OFF, ACC and  
ON/RUNNING.  
Door Mirrors  
•
•
•
Rotate the knob to select left (L) or right (R) rearview  
mirror.  
Note: Objects viewed in door mirrors may appear  
further away than they actually are.  
Move the knob in the desired direction to adjust the  
angle of the exterior mirror glass.  
Electric Door Mirror Glass Adjustment  
Upon completion of the adjustment, rotate the knob  
back to the central position, this will ensure no  
accidental adjustment of the mirror.  
*
Heating Elements  
The door mirrors have integral heating elements which  
disperse ice or mist from the glass. The heating elements  
operate while the Heated Rear Window  
is switched on.  
Note: The heating elements of rear window and mirror  
will only work when the power system is running.  
Mirror Folding  
The mirrors can be folded back towards the side windows  
into a ‘park’ position to enable the car to negotiate narrow  
openings and avoid collisions.  
50  
INSTRUMENTS AND CONTROLS  
The door mirrors will be folded automatically. Pushing  
the knob downwards again will return the mirrors to their  
original position.  
1
Operating the key fob lock/unlock buttons will fold/unfold  
the door mirrors.  
Note: Electrical folding door mirrors that have been  
moved from their positions by manual or accidental  
means must be reset by operating the knob to  
complete fold and deployment one time.  
IMPORTANT  
•
•
Door mirror glass adjustments and door mirror  
folding are operated by electrical motors. Operating  
them directly by hand may damage the internal  
components.  
*
Manual Folding of Door Mirror  
For vehicles not fitted with the electric door mirror fold  
option, the exterior mirrors can only be folded backwards  
manually.  
Washing or flushing door mirrors with high pressure  
water jets or car washes may result in electrical  
motor failure.  
*
Electric Folding of Door Mirror  
For vehicles fitted with electric door mirror folding, rotate  
the knob to the middle position, and push the knob down.  
51  
INSTRUMENTS AND CONTROLS  
Interior Rearview Mirror  
Adjust the body of the interior rearview mirror to achieve  
the best possible view. The anti-dazzle function of the  
interior rearview mirror helps to reduce glare from the  
headlamps of following vehicles at night.  
Manual Anti-dazzle Interior Rearview Mirror  
Move the lever at the base of the mirror forward to ‘dip'  
the mirror and achieve the anti-dazzle function. Normal  
visibility is restored by pulling the lever back again.  
Note: In some circumstances, the view reflected in a  
‘dipped’ manual mirror can confuse the driver as to the  
precise location of following vehicles.  
52  
INSTRUMENTS AND CONTROLS  
Sunvisor  
Note: Warnings and instructions on use of child  
restraint (3) are attached to both sides of the  
passenger sunvisor.  
NEVER use a rearward facing child restraints on a seat  
protected by an ACTIVE AIRBAG in front of it, DEATH  
or SERIOUS INJURY to the CHILD can occur. Refer  
to ‘Disabling the Passenger Airbag'.  
1
The vanity mirror on the driver side should  
only be used when the car is stationary.  
Sunvisors (1) are arranged on the roof ahead of both the  
driver and the front passenger. Some models have vanity  
mirror (2) , depending on the vehicle configuration. For  
the models which have vanity mirror, pull the sunvisor  
downward and slide the cover aside to use the vanity  
mirror.  
L
R
AG  
RB  
AI  
3
1
2
53  
INSTRUMENTS AND CONTROLS  
Windows  
Window Operation  
Ensure children are kept clear when raising or  
Power Operated Window Switch  
lowering a window.  
Improper use or activation of the electric  
windows by children could cause serious harm  
or even death. It is the responsibility of the  
driver and adult passengers to ensure that  
when carrying children the necessary steps  
are taken to isolate the window operation.  
This should include the removal of the key  
when children are left alone in the vehicle.  
Push the switch (1-4) down to lower, and pull the switch up  
to raise the window. The window will stop moving as soon  
as the switch is released (unless the ‘One-Touch’ function  
is active).  
1
2
3
4
5
Front Right Window Switch  
Front Left Window Switch  
Rear Right Window Switch  
Rear Left Window Switch  
Rear Window Isolation Switch  
Note: The front and rear passenger windows can also  
be operated by individual window switches, mounted  
on each door. The rear window switches will not be  
operated if the rear window isolation switch has been  
activated.  
54  
INSTRUMENTS AND CONTROLS  
Note: The electric window can be operated with the  
vehicle power system in the ACC, ON and RUNNING  
positions. (For safety: doors should be closed).  
close the window completely. Window movement can  
be stopped at a desired position at any time by briefly  
operating the switch again.  
1
The “Anti-Trap” function is a safety feature which prevents  
the window from fully closing if an obstruction is sensed -  
if this happens the window will open slightly to allow the  
obstruction to be removed.  
Rear Window Isolation Switch  
Press the button (5) to isolate the rear window controls,  
press again to restore control.  
Note: It is recommended that you ISOLATE the rear  
window switches when carrying a child.  
Note: DO NOT operate the power window controls  
continuously several times in a short time frame,  
otherwise the power window controls may be disabled  
to protect the motor. If this occurs, please wait a few  
seconds until the motor cools down. In the case of  
the driver’s window with "One Touch and Anti-Trap"  
please wait 30 seconds prior to operation. In some  
cases it may take 30 minutes to completely cool down,  
during which time the negative battery lead should  
not be disconnected.  
“One-Touch” Down  
The driver's window control switch (1) has 2 positions.  
Short press the window control switch to the "2" position  
and release. The window automatically descends to fully  
open. Window movement can be stopped at desired  
position at any time by briefly operating the switch again.  
“One Touch” Up with “Anti-Trap” *  
Note: If the battery is disconnected, the “One-Touch”  
and “Anti-Trap” features will be lost. To restore this  
feature, fully open and then fully close the window  
holding the switch for 5 seconds in the closed position.  
The driver's window control switch (1) has the  
“one-touch” up function. Lifting the switch to the "2"  
position for a short time and releasing will automatically  
55  
INSTRUMENTS AND CONTROLS  
*
Sunroof  
•
•
•
DO NOT use abrasive materials to clean the sunroof  
glass. Use only propriety glass cleaner or alcohol based  
solvent.  
The sunroof consists of two glass panels, only the front  
section can be opened by sliding or tilting. The sunshade  
can be opened or closed as a complete unit.  
DO NOT hold the operating switch in the open/close  
position for any length of time after operation is  
complete, this could damage the electrical components.  
Clean the sunroof regularly to maintain operation and  
performance. Visit an MG Authorised Repairer for  
service as required.  
Instructions  
DO NOT allow passengers to lean out of an  
open sunroof whilst the vehicle is in motion.  
Injuries may occur from objects such as tree  
branches.  
Safety of the vehicle occupants must be  
observed at all times. DO NOT allow limbs to  
be placed in the moving path of the sunroof  
at any time, injury may occur.  
•
•
•
Avoid fully opening the sunroof during rain showers.  
It is advised not to open the sunroof at high speeds.  
Where possible, please clean off any residual water or  
raindrops off the sunroof prior to opening. Failure to  
do so may result in water entering the car.  
56  
INSTRUMENTS AND CONTROLS  
Sunroof Operation  
Opening the Sunroof Glass using Tilt  
1
The sunroof will operate when the vehicle power system  
is in the ACC or ON/RUNNING modes.  
With the sunroof glass fully closed, press the rear part  
of the switch in the direction of the arrow as indicated  
in the graphic to fully 'tilt' the glass to the open position.  
Operation can be interrupted at the desired point by  
pressing the switch again.  
Sunroof Glass Operation  
Closing the Sunroof Glass from Tilt  
Pull down the rear of the switch to automatically close the  
sunroof in the direction as indicated by the arrow. Briefly  
pull down on the switch again will interrupt the operation  
at the desired position.  
To manually close the sunroof, pull down the rear of the  
switch in the direction as indicated by the arrow and hold,  
until the sunroof reaches the desired position.  
Opening the Sunroof Glass by Sliding  
Rotate the switch completely clockwise and  
hold until the sunroof slides fully open. To partially open  
the sunroof, place the switch in the required range position.  
57  
INSTRUMENTS AND CONTROLS  
Closing the Sunroof Glass by Sliding  
Opening the sunshade.  
Short press the button (2) to automatically open the  
sunshade to its full extent. Short press the button at any  
time to cancel the request and stop the sunshade at that  
position.  
Rotate  
the  
switch  
completely  
counterclockwise, the sunroof will slide fully closed. To  
partially close the sunroof, place the switch in the required  
range position.  
To manually open the sunshade, press and hold the button  
until the sunshade reaches the desired position, then  
release it.  
Sunroof Sunshade Operation  
Closing the Sunshade  
Short press the button (1) to automatically close the  
sunshade completely. Short press the button at any time to  
cancel the request and stop the sunshade at that position.  
To manually close the sunshade, press and hold the button  
until the sunshade reaches the desired position, and release  
it.  
Note: If the vehicle is to be parked in direct sunlight for  
a length of time it is recommended that the sunshade  
be closed to protect the interior trim components from  
damage, and to help regulate the in car temperatures.  
1
2
58  
INSTRUMENTS AND CONTROLS  
Anti-pinch Function  
To forcibly close the sunshade after an anti-pinch  
intervention, press the close button within 5 seconds and  
hold it until the sunshade is fully closed.  
1
The sunroof and sunshade feature an “Anti-Pinch”  
function, this is a safety feature which prevents the  
sunroof or sunshade from fully closing whilst in the  
automatic mode if an obstruction is sensed - if this  
happens the sunroof/sunshade will open slightly to allow  
the obstruction to be removed.  
Note: The anti pinch function is suspended during this  
operation.  
Note: The anti-pinch function only works when closing  
the sunroof during the slide operation.  
Forcibly Closing the Sunroof (over-riding the anti  
pinch)  
Sunroof Initialisation  
In the event of a power failure or battery disconnection  
when the sunroof glass or sunshade is in motion, the  
sunroof/sunshade will require initialisation when the power  
is restored.  
To forcibly close the sunroof glass after an anti-pinch  
intervention, gently pull the rear of the switch downwards  
within 5 seconds and hold in position until the sunroof  
glass is fully closed.  
To carry out the sunroof glass initialisation operation:  
Note: The anti pinch function is suspended during this  
operation.  
Fully close the glass - gently pull the rear of the switch  
downward and hold in position for 10 seconds, the sunroof  
will open a preset amount and stop, it will then close  
automatically- the sunroof glass is then initiailised. During  
the whole process, the switch must remain in the pulled  
down position.  
Forcibly Closing the Sunshade (over-riding the anti  
pinch)  
59  
INSTRUMENTS AND CONTROLS  
To carry out the sunshade initialisation operation:  
Fully close the sunshade - press the close switch and hold  
in position for 10 seconds, the sunshade will open a preset  
amount and stop, it will then close automatically- the  
sunshade is then initiailised. During the whole process,  
the switch must remain pressed.  
60  
INSTRUMENTS AND CONTROLS  
Interior Lights  
•
The vehicle power system is switched off, providing the  
sidelights have been illuminated during the previous 30  
seconds.  
1
Note: If a door or the tailgate is open for more than  
15 minutes, the front interior lamp will be switched off  
automatically to avoid battery drain.  
Press any one of buttons (2) to switch on the  
corresponding lamp, and press it again to switch the lamp  
off.  
Automatic Operation  
Press the interior lights switch button (1) to turn on  
automatic operation, and press it again to turn off the  
function.  
Interior light illumination occurs automatically whenever  
the following occur.  
•
•
The car is unlocked.  
Any door or the tailgate is opened.  
61  
INSTRUMENTS AND CONTROLS  
Power Socket  
Please ensure the socket blanking plug is  
inserted when the power socket is not in use.  
This will ensure no debris or foreign objects  
enter the socket preventing its use or cause  
short circuits.  
The 12V power socket has a voltage rating of  
12V, and the maximum power of 120 Watt,  
please DO NOT use any electrical appliance  
that exceeds this rating.  
Extended use of the accessory power socket  
and USB socket when the engine is switched  
off will cause premature discharging of the  
vehicle battery.  
The 12V power socket is located under the shift control  
knob assembly in the centre console. It can be used as  
a power supply when the START/STOP Switch is in the  
ACC or ON/RUNNING positions when the blanking plug  
is removed.  
Located to the right of the power socket are two USB  
ports. Both of them can be used to provide a 5V power  
supply or a data transmission connection.  
62  
INSTRUMENTS AND CONTROLS  
Note: The vehicle is not supplied with a cigar lighter.  
If required please contact your local MG Authorised  
Repairer.  
Note: Due to differences in configuration the charging  
function of the USB port will be slower.  
1
There are two USB ports located at the rear of the centre  
console, these provide 5V voltage when serving as the  
power outlet.  
There is also one USB port located in the rear view mirror  
mounting trim cover, this provides a 5V power source.  
63  
INSTRUMENTS AND CONTROLS  
Storage Devices  
Glove Box  
Instructions  
•
•
Please close all storage devices when the vehicle is in  
motion. Leaving these storage devices open may cause  
personal injury in cases of a sudden start-off, emergency  
braking and a car accident.  
Do not place flammable materials such as liquid or  
lighters in any storage devices. The heat in hot  
conditions may ignite flammable materials and lead to  
a fire.  
To open the glove box, pull the handle on the glove box  
cover (as indicated by the arrow).  
Push the box cover forward to close the glove box. Make  
sure the glove box is fully closed when the vehicle is in  
motion.  
64  
INSTRUMENTS AND CONTROLS  
Card Box  
Centre Console Armrest Box  
1
Lift the armrest (arrowed) to open the compartment cover.  
Put the cover down to close it.  
Located in the driver side lower dash trim panel.  
65  
INSTRUMENTS AND CONTROLS  
Loadspace  
The spare wheel/tyre repair kit and tool kit are stowed  
beneath the loadspace carpet, lift the carpet for access.  
Always refit the carpet after use.  
DO NOT place articles on the rear parcel  
shelf, they could move causing personal  
In addition, The loadspace carpet height can be adjusted by  
using the carpet bracket (figure 1, 2).  
，
injury in the event of an accident  
emergency braking or hard acceleration.  
The rear parcel shelf is connected to the tailgate using  
straps and hooks. When opening the tailgate, the shelf will  
automatically be raised.  
66  
INSTRUMENTS AND CONTROLS  
Cup Holder  
Centre Console Cup Holder(IPB)  
1
Do not place hot drinks in the cup holder  
whilst driving. Spillage may result in personal  
injury or damage.  
Centre Console Cup Holder(EPB)  
The centre console cup holder is situated at the front end  
of the centre console armrest assembly.  
The centre console cup holder is situated at the front end  
of the centre console armrest assembly.  
67  
INSTRUMENTS AND CONTROLS  
*
Roof Luggage Rack  
•
•
•
The overall height of the car is different when loads are  
fitted to the roof luggage rack. Please ensure there is  
adequate clearance when entering tunnels and garages.  
Ensure the loads carried by the roof luggage rack do  
not impede operation of the sunroof, roof antenna of  
tailgate opening.  
Roof loads MUST NOT exceed the maximum  
authorised load. This may lead to injury or  
vehicle damage.  
Loose or improperly fixed loads may fall from  
the roof luggage rack and lead to an accident  
or cause people injury.  
When installing or removing  
a
piece of loading  
equipment, follow the instructions provided by the  
manufacturer of the loading equipment.  
Maximum Authorised Load for the Roof  
When heavy or large items are carried  
on the roof luggage rack it may lead  
to changes in steering, handling and  
braking characteristics. Please avoid sharp  
manoeuvres, heavy braking and excessive  
acceleration.  
The maximum authorised load for the roof is 75 kg, this  
includes the weight of the roof loads and that of the loading  
equipment installed.  
Ensure you are aware of the weight of loads, and weigh  
them when necessary. Never exceed the maximum  
authorised load for the roof.  
Pay attention to the following in using the roof luggage rack:  
•
Secure loads toward the front of the roof as far as  
possible. distribute loads evenly.  
Periodical Check  
Always check the condition of the bolt connectors  
and fastenings before use. Periodically check the bolt  
connectors and fastenings for security.  
•
DO NOT use automatic car washes with loads on the  
roof luggage rack.  
68  

Related Topics

Instruments and Controls Instrument Pack Information Centre Warning Lights and Indicators Lights and Switches Wipers and Washers Steering System Horn Mirrors Sunvisor Windows Sunroof Interior Lights Power Socket Storage Devices Cup Holder Roof Luggage Rack

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot