Get Instruments and Controls -> Sunroof Guide for Mg Zs SUV First Generation (2017-2024)

INSTRUMENTS AND CONTROLS

*

Sunroof

•

DO NOT use abrasive materials to clean the sunroof

glass. Use only propriety glass cleaner or alcohol based

solvent.

The sunroof consists of two glass panels, only the front

section can be opened by sliding or tilting. The sunshade

can be opened or closed as a complete unit.

DO NOT hold the operating switch in the open/close

position for any length of time after operation is

complete, this could damage the electrical components.

Clean the sunroof regularly to maintain operation and

performance. Visit an MG Authorised Repairer for

service as required.

Instructions

DO NOT allow passengers to lean out of an

open sunroof whilst the vehicle is in motion.

Injuries may occur from objects such as tree

branches.

Safety of the vehicle occupants must be

observed at all times. DO NOT allow limbs to

be placed in the moving path of the sunroof

at any time, injury may occur.

•

Avoid fully opening the sunroof during rain showers.

It is advised not to open the sunroof at high speeds.

Where possible, please clean off any residual water or

raindrops off the sunroof prior to opening. Failure to

do so may result in water entering the car.

56

INSTRUMENTS AND CONTROLS

Sunroof Operation

Opening the Sunroof Glass using Tilt

1

The sunroof will operate when the vehicle power system

is in the ACC or ON/RUNNING modes.

With the sunroof glass fully closed, press the rear part

of the switch in the direction of the arrow as indicated

in the graphic to fully 'tilt' the glass to the open position.

Operation can be interrupted at the desired point by

pressing the switch again.

Sunroof Glass Operation

Closing the Sunroof Glass from Tilt

Pull down the rear of the switch to automatically close the

sunroof in the direction as indicated by the arrow. Brieﬂy

pull down on the switch again will interrupt the operation

at the desired position.

To manually close the sunroof, pull down the rear of the

switch in the direction as indicated by the arrow and hold,

until the sunroof reaches the desired position.

Opening the Sunroof Glass by Sliding

Rotate the switch completely clockwise and

hold until the sunroof slides fully open. To partially open

the sunroof, place the switch in the required range position.

57

INSTRUMENTS AND CONTROLS

Closing the Sunroof Glass by Sliding

Opening the sunshade.

Short press the button (2) to automatically open the

sunshade to its full extent. Short press the button at any

time to cancel the request and stop the sunshade at that

position.

Rotate

the

switch

completely

counterclockwise, the sunroof will slide fully closed. To

partially close the sunroof, place the switch in the required

range position.

To manually open the sunshade, press and hold the button

until the sunshade reaches the desired position, then

release it.

Sunroof Sunshade Operation

Closing the Sunshade

Short press the button (1) to automatically close the

sunshade completely. Short press the button at any time to

cancel the request and stop the sunshade at that position.

To manually close the sunshade, press and hold the button

until the sunshade reaches the desired position, and release

it.

Note: If the vehicle is to be parked in direct sunlight for

a length of time it is recommended that the sunshade

be closed to protect the interior trim components from

damage, and to help regulate the in car temperatures.

1

2

58

INSTRUMENTS AND CONTROLS

Anti-pinch Function

To forcibly close the sunshade after an anti-pinch

intervention, press the close button within 5 seconds and

hold it until the sunshade is fully closed.

1

The sunroof and sunshade feature an “Anti-Pinch”

function, this is a safety feature which prevents the

sunroof or sunshade from fully closing whilst in the

automatic mode if an obstruction is sensed - if this

happens the sunroof/sunshade will open slightly to allow

the obstruction to be removed.

Note: The anti pinch function is suspended during this

operation.

Note: The anti-pinch function only works when closing

the sunroof during the slide operation.

Forcibly Closing the Sunroof (over-riding the anti

pinch)

Sunroof Initialisation

In the event of a power failure or battery disconnection

when the sunroof glass or sunshade is in motion, the

sunroof/sunshade will require initialisation when the power

is restored.

To forcibly close the sunroof glass after an anti-pinch

intervention, gently pull the rear of the switch downwards

within 5 seconds and hold in position until the sunroof

glass is fully closed.

To carry out the sunroof glass initialisation operation:

Note: The anti pinch function is suspended during this

operation.

Fully close the glass - gently pull the rear of the switch

downward and hold in position for 10 seconds, the sunroof

will open a preset amount and stop, it will then close

automatically- the sunroof glass is then initiailised. During

the whole process, the switch must remain in the pulled

down position.

Forcibly Closing the Sunshade (over-riding the anti

pinch)

59

INSTRUMENTS AND CONTROLS

To carry out the sunshade initialisation operation:

Fully close the sunshade - press the close switch and hold

in position for 10 seconds, the sunshade will open a preset

amount and stop, it will then close automatically- the

sunshade is then initiailised. During the whole process,

the switch must remain pressed.

60

Instruments and Controls -> Sunroof for Your Mg Zs SUV First Generation (2017-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals