2014-2022 Mini One 2 Door MOBILITY User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

MOBILITY for Your Mini One 2 Door Third Generation (2014-2022)

AT A GLANCE
CONTROLS
DRIVING TIPS
MOBILITY
REFERENCE
Online Edition for Part no. 01 40 2 915 044 - X/16
Refueling
Vehicle features and op‐
tions
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your vehicle, e. g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be
observed.
General information
Observe the fuel recommendation, refer to
page 188, prior to refueling.
Safety information
NOTE
With a range of less than 30 miles/50 km
it is possible that the engine will no longer have
sufficient fuel. Engine functions are not ensured
anymore. There is a risk of property damage.
Refuel promptly.◀
Fuel cap
Opening
1.
Grasp the fuel filler flap at the rear edge
and open it.
2. Turn the fuel cap counterclockwise.
3. Place the fuel cap in the bracket attached
to the fuel filler flap.
Seite 186
MOBILITY
Refueling
186
Online Edition for Part no. 01 40 2 915 044 - X/16
Closing
WARNING
The retaining strap of the fuel cap can be
jammed and crushed during closing. The cap
cannot be correctly closed. Fuel or fuel vapors
can escape. There is a risk of injury or risk of
property damage. Pay attention that the retain‐
ing strap is not jammed or crushed when clos‐
ing the lid.◀
1. Fit the cap and turn it clockwise until you
clearly hear a click.
2. Close the fuel filler flap.
Manually unlocking fuel filler flap
E.g., in the event of an electrical malfunction.
Have the fuel filler flap checked by a dealer’s
service center or another qualified service cen‐
ter or repair shop.
Observe the following
when refueling
General information
The fuel tank is full when the filler nozzle clicks
off the first time.
Observe safety regulations posted at the gas
station.
Safety information
NOTE
Fuels are toxic and aggressive. Overfilling
of the fuel tank can damage the fuel system.
Painted surfaces may be damaged by contact
with fuel. Escaping fuel can harm the environ‐
ment. There is a risk of property damage. Avoid
overfilling.
◀
Seite 187
Refueling
MOBILITY
187
Online Edition for Part no. 01 40 2 915 044 - X/16
Fuel
Vehicle features and op‐
tions
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your vehicle, e. g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be
observed.
Fuel recommendation
General information
Depending on the region, many gas stations
sell fuel that has been customized to winter or
summer conditions. Fuel that is available in
winter helps make a cold start easier, for exam‐
ple.
Gasoline
General information
For the best fuel efficiency, the gasoline should
be sulfur-free or very low in sulfur content.
Fuels that are marked on the gas pump as con‐
taining metal must not be used.
Fuels with a maximum ethanol content of
25 %, i. e. E10 or E25, may be used for refuel‐
ing.
Ethanol should meet the following quality
standards:
US: ASTM 4806–xx
CAN: CGSB-3.511–xx
xx: comply with the current standard in each
case.
Safety information
NOTE
Do not press the Start/Stop button after
refueling with the wrong fuel. Furthermore, the
catalytic converter is permanently damaged.
There is a risk of property damage. Do not re‐
fuel or add the following in the case of gasoline
engines:
▷ Leaded gasoline.
▷ Metallic additives, e.g., manganese or iron.
Do not press the Start/Stop button after refuel‐
ing with the wrong fuel. Contact a dealer’s serv‐
ice center or another qualified service center or
repair shop.◀
NOTE
Incorrect fuels can damage the fuel sys‐
tem and the engine. There is a risk of damage
to property. Do not use fuels with a higher per‐
centage of ethanol than recommended. Do not
refuel with fuels containing methanol, e.g. M5
to M100.◀
NOTE
Fuel that does not comply with the mini‐
mum quality can compromise engine function
or cause engine damage. There is a risk of
property damage. Do not fill with fuel that does
not comply with the minimum quality.◀
If you use gasoline with this minimum AKI Rat‐
ing, the engine may produce knocking sounds
when starting at high outside temperatures.
This has no effect on the engine life.
CAUTION
The use of poor-quality fuels may result in
harmful engine deposits or damage. Addition‐
ally, problems relating to drivability, starting
and stalling, especially under certain environ‐
mental conditions such as high ambient tem‐
perature and high altitude, may occur.
Seite 188
MOBILITY
Fuel
188
Online Edition for Part no. 01 40 2 915 044 - X/16
If drivability problems are encountered, we rec‐
ommend switching to a high quality gasoline
brand and a higher octane grade — AKI num‐
ber — for a few tank fills. To avoid harmful en‐
gine deposits, it is highly recommended to pur‐
chase gasoline from Top Tier retailers.
Failure to comply with these recommendations
may result in the need for unscheduled mainte‐
nance.◀
Recommended fuel grade
MINI recommends AKI 91.
John Cooper Works:
MINI recommends AKI 93.
Minimum fuel grade
MINI recommends AKI 89.
John Cooper Works:
MINI recommends AKI 91.
Seite 189
Fuel
MOBILITY
189
Online Edition for Part no. 01 40 2 915 044 - X/16
Wheels and tires
Vehicle features and op‐
tions
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your vehicle, e. g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be
observed.
Tire inflation pressure
General information
The tire characteristics and tire inflation pres‐
sure influence the following:
▷ The service life of the tires.
▷ Road safety.
▷ Driving comfort.
Safety information
WARNING
A tire with low or missing tire inflation
pressure impacts handling, such as steering
and braking response. There is a risk of an acci‐
dent. Regularly check the tire inflation pressure,
and correct it as needed, e.g., twice a month
and before a long trip.◀
Checking the tire inflation pressure
Only check the tire inflation pressure when the
tires are cold. This means after driving no more
than 1.25 miles/2 km or when the vehicle has
been parked for at least 2 hours.
Tires heat up while driving, and the tire inflation
pressure increases along with the tire's temper‐
ature. The tire inflation pressure specifications
relate to cold tires or tires at ambient tempera‐
ture.
The displays of inflation devices may under-
read by up to 0.1 bar, 2 psi.
Tires have a natural, consistent loss of tire infla‐
tion pressure.
For Flat Tire Monitor: after correcting the tire
inflation pressure, reinitialize the Flat Tire Moni‐
tor.
For Tire Pressure Monitor: perform a reset of
the Tire Pressure Monitor after adjusting tire
pressure to a new value.
▷ Reinitialize the Flat Tire Monitor.
▷ Reinitialize the Tire Pressure Monitor.
Checking the inflation pressure of the
emergency wheel
Located behind the bumper on the underside
of the vehicle is an opening for checking the
tire inflation pressure.
Tire inflation pressure specifications
The tire inflation pressure table, refer to
page 191, contains all tire inflation pressure
specifications for the specified tire sizes at the
ambient temperature. The tire inflation pres‐
sure values apply to tire sizes approved by the
manufacturer of the vehicle for the vehicle
type.
Seite 190
MOBILITY
Wheels and tires
190
Online Edition for Part no. 01 40 2 915 044 - X/16
To identify the correct tire inflation pressure,
please note the following:
▷ Tire sizes of your vehicle.
▷ Maximum permitted driving speed.
Tire inflation pressures up to 100 mph/
160 km/h
For speeds of up to 100 mph/160 km/h and for
optimum driving comfort, note the pressure
values in the tire inflation pressure table, refer
to page 191, and adjust as necessary.
These pressure values can also be found on the
tire inflation pressure label on the driver's door
pillar.
Do not exceed a speed of 100 mph/160 km/h.
Tire inflation pressure values up to
100 mph/160 km/h
On 3-door models: COOPER
Tire size Pressure specifications in
bar/PSI
Specifications in
bar/PSI with cold
tires
175/60 R 16 86 H
M+S XL RSC
175/65 R 15 84 H
M+S A/S Std
175/65 R 15 84 H
M+S Std
175/65 R 15 84 H
Std
185/50 R 17 86 H
M+S XL RSC
195/55 R 16 87 H
M+S RSC
195/55 R 16 87
V M+S A/S RSC
195/55 R 16 87 W
RSC
205/45 R 17 88 V
M+S XL A/S RSC
205/45 R 17 88 V
M+S XL RSC
205/45 R 17 88 W
XL RSC
205/40 R 18 86 W
XL RSC
2.4 / 35 2.4 / 35
Emergency wheel
T 115/70 R 15 90
M
Speed up to a max. of
50 mph / 80 km/h
4.2 / 60
Seite 191
Wheels and tires
MOBILITY
191
Online Edition for Part no. 01 40 2 915 044 - X/16
On 3-door models: COOPER S
Tire size Pressure specifications in
bar/PSI
Specifications in
bar/PSI with cold
tires
195/55 R 16 87 H
M+S RSC
195/55 R 16 87 V M
+S A/S RSC
195/55 R 16 87 W
RSC
2.4 / 35 2.4 / 35
175/60 R 16 86 H
M+S XL RSC
185/50 R 17 86 H
M+S XL RSC
205/45 R 17 88 V M
+S XL A/S RSC
205/45 R 17 88 V M
+S XL RSC
205/45 R 17 88 W
XL RSC
205/40 R 18 86 W
XL RSC
2.6 / 38 2.4 / 35
On 3-door models: JOHN COOPER
WORKS
Tire size Pressure specifications in
bar/PSI
Specifications in
bar/PSI with cold
tires
185/50 R 17 86 H
M+S XL RSC
205/45 R 17 88 W
XL RSC
205/45 R 17 88 V
M+S XL A/S RSC
205/45 R 17 88 V
M+S XL RSC
205/40 R 18 86 W
XL RSC
2.9 / 42 2.7 / 39
On 5-door models: COOPER
Tire size Pressure specifications in
bar/PSI
Specifications in
bar/PSI with cold
tires
175/65 R 15 84 H
M+S A/S Std
175/65 R 15 84 H
M+S Std
175/65 R 15 84 H
Std
195/55 R 16 87 H
M+S RSC
195/55 R 16 87
V M+S A/S RSC
195/55 R 16 87 W
RSC
2.5 / 36 2.3 / 33
Seite 192
MOBILITY
Wheels and tires
192
Online Edition for Part no. 01 40 2 915 044 - X/16
Tire size Pressure specifications in
bar/PSI
205/45 R 17 88 V
M+S XL A/S RSC
205/45 R 17 88 V
M+S XL RSC
205/45 R 17 88 W
XL RSC
2.5 / 36 2.4 / 35
175/60 R 16 86 H
M+S XL RSC
205/40 R 18 86 W
XL RSC
185/50 R 17 86 H
M+S XL RSC
2.6 / 38 2.6 / 38
Emergency wheel
T 115/70 R 15 90
M
Speed up to a max. of
50 mph / 80 km/h
4.2 / 60
On 5-door models: COOPER S
Tire size Pressure specifications in
bar/PSI
Specifications in
bar/PSI with cold
tires
195/55 R 16 87 H
M+S RSC
195/55 R 16 87 V M
+S A/S RSC
195/55 R 16 87 W
RSC
2.5 / 36 2.3 / 33
175/60 R 16 86 H
M+S XL RSC
205/45 R 17 88 V M
+S XL A/S RSC
205/45 R 17 88 V M
+S XL RSC
205/45 R 17 88 W
XL RSC
185/50 R 17 86 H
M+S XL RSC
205/40 R 18 86 W
XL RSC
2.7 / 39 2.7 / 39
Tire inflation pressures at max. speeds
above 100 mph/160 km/h
WARNING
In order to drive at maximum speeds in
excess of 100 mph/160 km/h, please observe,
and, if necessary, adjust tire pressures for
speeds exceeding 100 mph/160 km/h from the
relevant table on the following pages. Other‐
wise, tire damage and accidents could occur.◀
For speeds over 100 mph/160 km/h and for op‐
timum driving comfort, note the pressure val‐
ues in the tire inflation pressure table, refer to
page 194, and adjust as necessary.
Seite 193
Wheels and tires
MOBILITY
193
Online Edition for Part no. 01 40 2 915 044 - X/16
Tire inflation pressure values over
100 mph/160 km/h
On 3-door models: COOPER
Tire size Pressure specifications in
bar/PSI
Specifications in
bar/PSI with cold
tires
175/65 R 15 84 H
M+S A/S Std
175/65 R 15 84 H
M+S Std
175/65 R 15 84 H
Std
175/60 R 16 86 H
M+S XL RSC
185/50 R 17 86 H
M+S XL RSC
195/55 R 16 87 H
M+S RSC
195/55 R 16 87
V M+S A/S RSC
195/55 R 16 87 W
RSC
205/45 R 17 88 V
M+S XL A/S RSC
205/45 R 17 88 V
M+S XL RSC
205/45 R 17 88 W
XL RSC
205/40 R 18 86 W
XL RSC
2.8 / 41 2.6 / 38
Emergency wheel
T 115/70 R 15 90
M
Speed up to a max. of
50 mph / 80 km/h
4.2 / 60
On 3-door models: COOPER S
Tire size Pressure specifications in
bar/PSI
Specifications in
bar/PSI with cold
tires
195/55 R 16 87 H
M+S RSC
195/55 R 16 87 V M
+S A/S RSC
195/55 R 16 87 W
RSC
2.8 / 41 2.6 / 38
175/60 R 16 86 H
M+S XL RSC
185/50 R 17 86 H
M+S XL RSC
205/45 R 17 88 V M
+S XL A/S RSC
205/45 R 17 88 V M
+S XL RSC
205/45 R 17 88 W
XL RSC
205/40 R 18 86 W
XL RSC
3.1 / 45 2.9 / 42
Seite 194
MOBILITY
Wheels and tires
194
Online Edition for Part no. 01 40 2 915 044 - X/16
On 3-door models: JOHN COOPER
WORKS
Tire size Pressure specifications in
bar/PSI
Specifications in
bar/PSI with cold
tires
185/50 R 17 86 H
M+S XL RSC
205/45 R 17 88 W
XL RSC
205/45 R 17 88 V
M+S XL A/S RSC
205/45 R 17 88 V
M+S XL RSC
3.1 / 45 2.9 / 42
205/40 R 18 86 W
XL RSC
3.4 / 49 3.2 / 46
On 5-door models: COOPER
Tire size Pressure specifications in
bar/PSI
Specifications in
bar/PSI with cold
tires
175/65 R 15 84 H
M+S A/S Std
175/65 R 15 84 H
M+S Std
175/65 R 15 84 H
Std
195/55 R 16 87 H
M+S RSC
195/55 R 16 87
V M+S A/S RSC
195/55 R 16 87 W
RSC
205/45 R 17 88 V
M+S XL A/S RSC
205/45 R 17 88 V
M+S XL RSC
205/45 R 17 88 W
XL RSC
2.8 / 41 2.6 / 38
175/60 R 16 86 H
M+S XL RSC
185/50 R 17 86 H
M+S XL RSC
205/40 R 18 86 W
XL RSC
2.8 / 41 2.8 / 41
Emergency wheel
T 115/70 R 15 90
M
Speed up to a max. of
50 mph / 80 km/h
4.2 / 60
Seite 195
Wheels and tires
MOBILITY
195
Online Edition for Part no. 01 40 2 915 044 - X/16
On 5-door models: COOPER S
Tire size Pressure specifications in
bar/PSI
Specifications in
bar/PSI with cold
tires
195/55 R 16 87 H
M+S RSC
195/55 R 16 87 V M
+S A/S RSC
195/55 R 16 87 W
RSC
2.8 / 41 2.8 / 41
175/60 R 16 86 H
M+S XL RSC
205/45 R 17 88 V M
+S XL A/S RSC
205/45 R 17 88 V M
+S XL RSC
205/45 R 17 88 W
XL RSC
185/50 R 17 86 H
M+S XL RSC
205/40 R 18 86 W
XL RSC
3.1 / 45 3.1 / 45
Tire identification marks
Tire size
205/45 R 17 84 V
205: nominal width in mm
45: aspect ratio in %
R: radial tire code
17: rim diameter in inches
84: load rating, not for ZR tires
F: speed rating, before the R on ZR tires
Maximum tire load
Maximum tire load is the maximum permissible
weight for which the tire is approved.
Locate the maximum tire load on the tire side‐
wall and the Gross Axle Weight Rating – GAWR –
on the certification label on the driver’s door
pillar. Divide the tire load by 1.1. It must be
greater than one-half of the vehicle’s Gross
Axle Weight Rating – GAWR. Note, front vs. rear
GAWR and tire loads, respectively.
Speed letter
T = up to 118 mph, 190 km/h
H = up to 131 mph, 210 km/h
V = up to 150 mph, 240 km/h
W = up to 167 mph, 270 km/h
Y = up to 186 mph, 300 km/h
Tire Identification Number
DOT code: DOT xxxx xxx 3816
xxxx: manufacturer code for the tire brand
xxx: tire size and tire design
3816: tire age
Tires with DOT codes meet the guidelines of
the U.S. Department of Transportation.
Tire age
DOT … 3816: the tire was manufactured in the
38th week of 2016.
Recommendation
Regardless of wear and tear, replace tires at
least every 6 years.
Uniform Tire Quality Grading
Quality grades can be found where applicable
on the tire sidewall between tread shoulder
and maximum section width.
E.g.: Treadwear 200; Traction AA; Temperature
A
Seite 196
MOBILITY
Wheels and tires
196
Online Edition for Part no. 01 40 2 915 044 - X/16
DOT Quality Grades
Treadwear
Traction AA A B C
Temperature A B C
All passenger vehicle tires must conform to
Federal Safety Requirements in addition to
these grades.
Treadwear
The treadwear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specified gov‐
ernment test course. E.g., a tire graded 150
would wear one and one-half, 1 g, times as well
on the government course as a tire graded 100.
The relative performance of tires depends upon
the actual conditions of their use, however, and
may depart significantly from the norm due to
variations in driving habits, service practices
and differences in road characteristics and cli‐
mate.
Traction
The traction grades, from highest to lowest, are
AA, A, B, and C.
Those grades represent the tire's ability to stop
on wet pavement as measured under control‐
led conditions on specified government test
surfaces of asphalt and concrete. A tire marked
C may have poor traction performance.
The traction grade assigned to this tire is based
on straight-ahead braking traction tests, and
does not include acceleration, cornering, hy‐
droplaning, or peak traction characteristics.
Temperature
The temperature grades are A, the highest, B,
and C, representing the tire's resistance to the
generation of heat and its ability to dissipate
heat when tested under controlled conditions
on a specified indoor laboratory test wheel.
Sustained high temperature can cause the ma‐
terial of the tire to degenerate and reduce tire
life, and excessive temperature can lead to
sudden tire failure. The grade C corresponds to
a level of performance which all passenger ve‐
hicle tires must meet under the Federal Motor
Vehicle Safety Standard No. 109. Grades Band A
represent higher levels of performance on the
laboratory test wheel than the minimum re‐
quired by law.
WARNING
The temperature grade for this tire is es‐
tablished for a tire that is properly inflated and
not overloaded. Excessive speed, underinfla‐
tion, or excessive loading, either separately or
in combination, can cause heat buildup and
possible tire failure.◀
RSC – Run-flat tires
Run-flat tires, refer to page 200, are labeled
with a circular symbol containing the letters
RSC marked on the sidewall.
M+S
Winter and all-season tires with better cold
weather performance than summer tires.
Tire tread
Summer tires
Do not drive with a tire tread depth of less than
0.12 in/3 mm.
There is an increased risk of hydroplaning if the
tire tread depth is less than 0.12 inches/3 mm.
Winter tires
Do not drive with a tire tread depth of less than
0.16 inches/4 mm.
Below a tread depth of 0.16 inches/4 mm, tires
are less suitable for winter operation.
Seite 197
Wheels and tires
MOBILITY
197
Online Edition for Part no. 01 40 2 915 044 - X/16
Minimum tread depth
Wear indicators are distributed around the tire's
circumference and have the legally required
minimum height of 0.063 inches/1.6 mm.
They are marked on the side of the tire with
TWI, Tread Wear Indicator.
Tire damage
General information
Inspect your tires regularly for damage, foreign
objects lodged in the tread, and tread wear.
Driving over rough or damaged road surfaces,
as well as debris, curbs and other obstacles can
cause serious damage to wheels, tires and sus‐
pension parts. This is more likely to occur with
low-profile tires, which provide less cushioning
between the wheel and the road. Be careful to
avoid road hazards and reduce your speed, es‐
pecially if your vehicle is equipped with low-
profile tires.
Indications of tire damage or other vehicle mal‐
functions:
▷ Unusual vibrations while driving.
▷ Unusual handling such as a strong ten‐
dency to pull to the left or right.
Damage can, e.g., be caused by driving over
curbs, road damage, or similar things.
Safety information
WARNING
Damaged tires can lose tire inflation pres‐
sure, which can lead to loss of vehicle control.
There is a risk of an accident. If tire damage is
suspected while driving, immediately reduce
speed and stop. Have wheels and tires
checked. For this purpose, drive carefully to the
nearest dealer’s service center or another
qualified service center or repair shop. Have
vehicle towed or transported as needed.◀
WARNING
Damaged tires can lose tire inflation pres‐
sure, which can lead to loss of vehicle control.
There is a risk of an accident. Do not repair
damaged tires, but have them replaced.◀
Changing wheels and
tires
Mounting
Have mounting and wheel balancing carried
out by a dealer’s service center or another
qualified service center or repair shop.
Wheel and tire combination
General information
You can ask the dealer’s service center or an‐
other qualified service center or repair shop
about the correct wheel/tire combination and
wheel rim versions for the vehicle.
Incorrect wheel and tire combinations impair
the function of a variety of systems such as ABS
or DSC.
To maintain good handling and vehicle re‐
sponse, use only tires with a single tread con‐
figuration from a single manufacturer.
Following tire damage, have the original wheel
and tire combination remounted on the vehicle
as soon as possible.
Seite 198
MOBILITY
Wheels and tires
198
Online Edition for Part no. 01 40 2 915 044 - X/16
Safety information
WARNING
Wheels and tires which are not suitable
for your vehicle can damage parts of the vehi‐
cle, for instance due to contact with the body
due to tolerances despite the same official size
rating. There is a risk of an accident. The manu‐
facturer of your vehicle strongly suggests that
you use wheels and tires that have been rec‐
ommended by the vehicle manufacturer for
your vehicle type.◀
Recommended tire brands
For each tire size, the manufacturer of the vehi‐
cle recommends certain tire brands. These can
be identified by a star on the tire sidewall.
New tires
Tire traction is not optimal due to manufactur‐
ing circumstances when tires are brand-new;
they achieve their full traction potential after a
break-in time.
Drive conservatively for the first
200 miles/300 km.
Retreaded tires
The manufacturer of your vehicle does not rec‐
ommend the use of retreaded tires.
WARNING
Retreaded tires can have different tire
casing structures. With advanced age the serv‐
ice life can be limited. There is a risk of an acci‐
dent. The manufacturer of your vehicle does
not recommend the use of retreaded tires.◀
Winter tires
Winter tires are recommended for operating on
winter roads.
Although so-called all-season M+S tires provide
better winter traction than summer tires, they
do not provide the same level of performance
as winter tires.
Maximum speed of winter tires
If the maximum speed of the vehicle is higher
than the permissible speed for the winter tires,
then a respective symbol is displayed in your
field of vision. The label is available from a
dealer’s service center or another qualified
service center or repair shop.
With mounted winter tires, observe and adhere
to the permissible maximum speed.
Run-flat tires
If you are already using run-flat tires, for your
own safety you should replace them only with
the same kind. No spare tire is available in the
case of a flat tire. Further information is availa‐
ble from a dealer’s service center or another
qualified service center or repair shop.
Rotating wheels between axles
Different wear patterns can occur on the front
and rear axles depending on individual driving
conditions. The tires can be rotated between
the axles to achieve even wear. Further infor‐
mation is available from a dealer’s service cen‐
ter or another qualified service center or repair
shop. After rotating, check the tire pressure and
correct if needed.
Storage
Store wheels and tires in a cool, dry and dark
place.
Always protect tires against all contact with oil,
grease and fuels.
Seite 199
Wheels and tires
MOBILITY
199
Online Edition for Part no. 01 40 2 915 044 - X/16
Do not exceed the maximum tire inflation pres‐
sure indicated on the side wall of the tire.
Run-flat tires
Concept
Runflat tires permit continued driving under re‐
stricted conditions even in the event of a com‐
plete loss of tire inflation pressure.
General information
The wheels are composed of tires that are self-
supporting to a limited degree.
The support of the sidewall allows the tire to re‐
main drivable to a restricted degree in the
event of a tire inflation pressure loss.
Follow the instructions for continued driving
with a flat tire.
Label
RSC label on the tire sidewall.
Changing run-flat tires
For your own safety, only use run-flat tires. No
spare tire is available in the case of a flat tire.
A dealer’s service center will be glad to answer
additional questions at any time.
Repairing a flat tire
Safety measures
▷
Park the vehicle as far away as possible
from passing traffic and on solid ground.
▷ Switch on the hazard warning system.
▷ Secure the vehicle against rolling away by
setting the parking brake.
▷ Have all vehicle occupants get out of the
vehicle and ensure that they remain out‐
side the immediate area in a safe place,
such as behind a guardrail.
▷ If necessary, set up a warning triangle or
portable hazard warning light at a sufficient
distance.
▷ Change wheels only on a flat, solid and slip-
resistant surface. On soft or slippery
ground, for example snow, ice, tiles, etc.,
the vehicle or the vehicle jack may slip
away sideways.
▷ Do not place wood blocks or similar items
under the vehicle jack; otherwise, it cannot
reach its carrying capacity because of the
restricted height.
▷ If the vehicle is raised, do not lie under the
vehicle and do not start the engine, or else
there is a danger to life.
Mobility System
The concept
With the Mobility System, minor tire damage
can be sealed temporarily to enable continued
travel. To accomplish this, sealant is pumped
into the tires, which seals the damage from the
inside.
The compressor can be used to check the tire
inflation pressure.
Seite 200
MOBILITY
Wheels and tires
200
Online Edition for Part no. 01 40 2 915 044 - X/16
General information
▷
Follow the instructions on using the Mobi‐
lity System found on the compressor and
sealant container.
▷ Use of the Mobility System may be ineffec‐
tive if the tire puncture measures approx.
1/8 inches/4 mm or more.
▷ Contact a dealer’s service center or another
qualified service center or repair shop if the
tire cannot be made drivable.
▷ If possible, do not remove foreign bodies
that have penetrated the tire.
▷ Pull the speed limit sticker off the sealant
container and apply it to the steering
wheel.
▷ The use of a sealant can damage the TPM
wheel electronics. In this case, have the
electronics checked and replaced at the
next opportunity.
Overview
Storage
The Mobility System is located under the cargo
floor panel.
Sealant container
▷ Sealant container, arrow 1.
▷ Filling hose, arrow 2.
Observe use-by date on the sealant container.
Compressor
1 Sealant container unlocking
2 Holder for sealant container
3 Inflation pressure dial
4 Reduce inflation pressure
5 On/off switch
6 Compressor
7 Connector/cable for socket
8 Connection hose
Filling the tire with sealant
Safety information
DANGER
If the exhaust pipe is blocked or ventila‐
tion is insufficient, harmful exhaust gases can
enter into the vehicle. The exhaust gases con‐
tain carbon monoxide, an odorless and color‐
less but highly toxic gas. In enclosed areas, ex‐
haust gases can also accumulate outside of the
vehicle. There is danger to life. Keep the ex‐
haust pipe free and ensure sufficient ventila‐
tion.◀
NOTE
The compressor can overheat during ex‐
tended operation. There is a risk of property
damage. Do not run the compressor for more
than 10 min.
◀
Seite 201
Wheels and tires
MOBILITY
201
Online Edition for Part no. 01 40 2 915 044 - X/16
Filling
1. Shake the sealant container.
2. Pull filling hose completely out of the cover
of the sealant container. Do not kink the
hose.
3. Slide the sealant container into the holder
on the compressor housing, ensuring that it
engages audibly.
4. Screw the filling hose of the sealant con‐
tainer onto the tire valve of the nonworking
wheel.
5. With the compressor switched off, insert
the plug into the power socket inside the
vehicle.
6. With the ignition turned on or the engine
running, switch on the compressor.
Let the compressor run for max. 10 minutes to
fill the tire with sealant and achieve a tire infla‐
tion pressure of approx. 2.5 bar.
While the tire is being filled with sealant, the
tire inflation pressure may sporadically reach
approx. 5 bar. Do not switch off the compressor
at this point.
Seite 202
MOBILITY
Wheels and tires
202
Online Edition for Part no. 01 40 2 915 044 - X/16
Checking and adjusting the tire
inflation pressure
Checking
1. Switch off the compressor.
2. Read the tire inflation pressure on the tire
pressure gage.
To continue the trip, a tire inflation pressure of
at least 2 bar must be reached.
Removing and stowing the sealant
container
1. Unscrew the filling hose of the sealant con‐
tainer from the wheel.
2. Press the red release button.
3. Remove the sealant container from the
compressor.
4. Wrap the empty sealant container in suita‐
ble material to avoid dirtying the cargo
area.
Minimum tire inflation pressure is not
reached
1. Pull the connector out of the power socket
inside the vehicle.
2. Drive 33 ft/10 m forward and back to dis‐
tribute the sealant in the tire.
3. Screw the connection hose of the compres‐
sor directly onto the tire valve stem.
4. Insert the connector into the power socket
inside the vehicle.
5. With the ignition turned on or the engine
running, switch on the compressor.
If a tire inflation pressure of at least 2 bar
cannot be reached, contact your dealer’s
service center or another qualified service
center or repair shop.
If a tire inflation pressure of at least 2 bar is
reached, see Minimum tire inflation pres‐
sure is reached.
6. Unscrew the connection hose of the com‐
pressor from the tire valve.
7. Pull the connector out of the power socket
inside the vehicle.
8. Stow the Mobility System in the vehicle.
Minimum tire inflation pressure is
reached
1. Stow the Mobility System in the vehicle.
2. Immediately drive approx. 5 miles/10 km to
ensure that the sealant is evenly distributed
in the tire.
Do not exceed a speed of 50 mph/80 km/h.
If possible, do not drive at speeds less than
12 mph/20 km/h.
Seite 203
Wheels and tires
MOBILITY
203
Online Edition for Part no. 01 40 2 915 044 - X/16
Adjustment
1. Stop at a suitable location.
2. Screw the connection hose of the compres‐
sor directly onto the tire valve stem.
3. Insert the connector into the power socket
inside the vehicle.
4. Correct the tire inflation pressure to at least
2.0 bar.
▷ Increase pressure: with the ignition
turned on or the engine running, switch
on the compressor.
▷ To reduce the pressure: press the but‐
ton on the compressor.
5. Unscrew the connection hose of the com‐
pressor from the tire valve.
6. Pull the connector out of the power socket
inside the vehicle.
7. Stow the Mobility System in the vehicle.
Continuing the trip
Do not exceed the maximum permissible speed
of 50 mph/80 km/h.
Reinitialize the Flat Tire Monitor, refer to
page 113.
Reinitialize the Tire Pressure Monitor, refer to
page
109.
Replace the nonworking tire and the sealant
container of the Mobility System promptly.
Snow chains
Fine-link snow chains
The manufacturer of your vehicle recommends
use of fine-link snow chains. Certain types of
fine-link snow chains have been tested by the
manufacturer of the vehicle and recommended
as road-safe and suitable.
Information regarding suitable snow chains is
available from a dealer’s service center or an‐
other qualified service center or repair shop.
Use
WARNING
With the mounting of snow chains on un‐
suitable tires, the snow chains can come into
contact with vehicle parts. There is a risk of ac‐
cidents or risk of property damage. Only mount
snow chains on tires that are designated by
their manufacturer as suitable for the use of
snow chains.◀
Use only in pairs on the front wheels, equipped
with the tires of the following size:
▷ 175/65 R 15.
▷ 175/60 R 16.
▷ 185/50 R 17.
John Cooper Works:
185/50 R 17.
Follow the snow chain manufacturer's instruc‐
tions.
Make sure that the snow chains are always suf‐
ficiently tight. Re-tighten as needed according
to the snow chain manufacturer's instructions.
Do not initialize the Flat Tire Monitor after
mounting snow chains, as doing so may result
in incorrect readings.
Seite 204
MOBILITY
Wheels and tires
204
Online Edition for Part no. 01 40 2 915 044 - X/16
Do not initialize the Tire Pressure Monitor after
mounting snow chains, as doing so may result
in incorrect readings.
When driving with snow chains, briefly activate
Dynamic Traction Control, if needed.
Maximum speed with snow chains
Do not exceed a speed of 30 mph/50 km/h
when using snow chains.
Changing wheels/tires
General information
When using runflat tires or tire sealants, a tire
does not always need to be changed immedi‐
ately in the event of pressure loss due to a flat
tire.
If needed, the tools for changing wheels are
available as accessories from a dealer’s service
center or another qualified service center or re‐
pair shop.
Safety information
WARNING
The jack, issued by the vehicle manufac‐
turer, is provided in order to perform a wheel
change in the event of a breakdown. The jack is
not designed for frequent use; for example,
changing from summer to winter tires.. Using
the jack frequently may cause it to become
jammed or damaged. There is a risk of injury
and risk of damage to property. Only use the
jack to attach an emergency or spare wheel in
the event of a breakdown.◀
WARNING
On soft or slippery ground, e.g., snow, ice,
tiles, etc., the vehicle jack can slip away. There
is a risk of injury. If possible, change the tire/
wheel on a flat, solid and slip-resistant sur‐
face.
◀
WARNING
The vehicle jack is only provided for
short-term lifting of the vehicle for wheel
changes. Even if all safety measures are ob‐
served, there is a risk of the raised vehicle fall‐
ing, if the vehicle jack tilts over. There is a risk
of injuries or danger to life. If the vehicle is
raised, do not lie under the vehicle and do not
start the engine.◀
WARNING
The vehicle jack is optimized for lifting
the vehicle and for the jacking points on the ve‐
hicle only. There is a risk of injury. Do not lift
any other vehicle or cargo using the vehicle
jack.◀
WARNING
If the vehicle jack is not inserted into the
jacking point provided for this purpose, the ve‐
hicle may be damaged or the vehicle jack may
slip when it is being cranked up. There is a risk
of injury or risk of damage to property. When
cranking up the vehicle jack, ensure that it is in‐
serted in the jacking point next to the wheel
housing.◀
WARNING
A vehicle that is raised on a vehicle jack
may fall off of the jack if lateral forces are ex‐
erted on it. There is a risk of injury and risk of
damage to property. While the vehicle is raised,
do not exert lateral forces on the vehicle or pull
abruptly on the vehicle. Have a stuck wheel re‐
moved by a dealer’s service center or another
qualified service center or repair shop.◀
Securing the vehicle against rolling
General information
The vehicle manufacturer recommends to addi‐
tionally secure the vehicle against rolling away
when changing a wheel.
Seite 205
Wheels and tires
MOBILITY
205
Online Edition for Part no. 01 40 2 915 044 - X/16
On a level surface
Place wheel chocks or other suitable objects in
front and behind the wheel that is diagonal to
the wheel to be changed.
On a slight downhill gradient
If you need to change a wheel on a slight
downhill gradient, place chocks and other suit‐
able objects, for example a rock, under the
wheels of both the front and rear axles against
the rolling direction.
Preparing the vehicle
▷
Park the vehicle as far away as possible
from passing traffic and on solid and non-
slip ground.
▷ Switch on the hazard warning system.
▷ Set the parking brake.
▷ Engage a gear or move the selector lever to
position P.
▷ As soon as the traffic flow permits, have all
vehicle occupants get out of the vehicle
and ensure that they remain outside the
immediate area in a safe place, such as be‐
hind a guardrail.
▷ Depending on your vehicle's equipment,
remove the tool and the emergency wheel
from the vehicle.
▷ If necessary, set up a warning triangle or
portable hazard warning lamp at an appro‐
priate distance.
▷ Do not place wood blocks or similar items
under the vehicle jack; otherwise, it cannot
reach its carrying capacity because of the
restricted height.
▷ Also secure the vehicle against rolling.
▷ Loosen the lug bolts a half turn.
Jacking points for the vehicle jack
The jacking points for the vehicle jack are lo‐
cated at the marked positions.
Jacking up the vehicle
WARNING
Hands and fingers can be jammed when
using the vehicle jack. There is a risk of injury.
Comply with the described hand position and
Seite 206
MOBILITY
Wheels and tires
206
Online Edition for Part no. 01 40 2 915 044 - X/16
do not change this position while using the ve‐
hicle jack.◀
1. Hold the jack with one hand, arrow 1, and
grasp the crank or lever with your other
hand, arrow 2.
2. Insert the vehicle jack into the rectangular
recess of the jacking point closest to the
wheel to be changed.
3. Extend the vehicle jack by turning the crank
or lever clockwise.
4. Take your hand away from the jack as soon
as the vehicle jack is under load and con‐
tinue turning the crank or lever with one
hand.
5. Make sure that the vehicle jack foot is ex‐
tended vertically.
6. Make sure that the vehicle jack foot stands
vertically and perpendicularly beneath the
jacking point after extending the vehicle
jack.
7. Crank up the vehicle jack until the entire
surface of the jack is in contact with the
ground and the wheel in question is raised
a maximum of 1.2 inches/3 cm off the
ground.
Mounting a wheel
Mount one emergency wheel only.
1. Unscrew the lug bolts and remove the
wheel.
2. Put the new wheel or emergency wheel on
and screw in at least two bolts in a cross‐
wise pattern until hand-tight.
If non-original light-alloy wheels of the ve‐
hicle manufacturer are mounted, the ac‐
companying lug bolts may have to be used
as well.
3. Hand-tighten the remaining lug bolts and
tighten all bolts well in a crosswise pattern.
Seite 207
Wheels and tires
MOBILITY
207
Online Edition for Part no. 01 40 2 915 044 - X/16
4. Turn the crank on the vehicle jack counter‐
clockwise to retract the jack and lower the
vehicle.
5. Remove the vehicle jack.
After the wheel change
1.
Tighten the lug bolts crosswise. The tight‐
ening torque is 101 lb ft/140 Nm.
2. Stow the nonworking wheel in the cargo
area.
The nonworking wheel cannot be stored
under the cargo floor panel because of its
size.
3. Check tire inflation pressure at the next op‐
portunity and correct as needed.
4. Reinitialize the Flat Tire Monitor.
Reset the Tire Pressure Monitor.
5. Check to make sure the lug bolts are tight
with a calibrated torque wrench.
6. Have the damaged tire replaced at the
nearest dealer’s service center or another
qualified service center or repair shop.
emergency wheel
General information
In the event of a flat tire, the emergency wheel
can be used in place of the wheel with the de‐
fective tire. The emergency wheel is only in‐
tended for temporary use until the defective
tire/wheel is replaced.
Removing the emergency wheel
The emergency wheel is housed in a well on
the underbody of the vehicle. The screw con‐
nection of the emergency wheel is in the cargo
area underneath the floor mat, on the floor of
the storage compartment for the onboard vehi‐
cle tool kit.
1. Loosen the nut using the wheel wrench
from the onboard vehicle tool kit.
2. Remove the retaining plate.
3. Screw wheel lug wrench onto the thread
and hold in place with one hand.
4. Unlock the locking hexagon of the emer‐
gency wheel well using the hexagon at‐
tached to retaining plate.
5. Lower the emergency wheel with the wheel
wrench.
6. Unscrewing the wheel wrench
7. Pull out the well with emergency wheel un‐
der the vehicle toward the rear.
Seite 208
MOBILITY
Wheels and tires
208
Online Edition for Part no. 01 40 2 915 044 - X/16
8. Remove the spacer and emergency wheel
from the well.
9. Stow the well and spacer in the vehicle.
Replacing the tires
1.
Have the damaged tire replaced.
2. Replace the emergency wheel with the new
wheel.
Installing the emergency wheel
Have the emergency wheel installed back into
the vehicle by a dealer’s service center or an‐
other qualified service center or repair shop.
Safety information
WARNING
The emergency wheel has particular di‐
mensions. When driving with an emergency
wheel, changed driving properties may occur at
higher speeds, e.g., reduced lane stability when
braking, longer braking distance and changed
self-steering properties in the limit area. There
is a risk of an accident. Drive moderately and
do not exceed a speed of 50 mph/80 km/h.◀
Seite 209
Wheels and tires
MOBILITY
209
Online Edition for Part no. 01 40 2 915 044 - X/16
Engine compartment
Vehicle features and op‐
tions
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your vehicle, e. g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be
observed.
Important features in the engine compartment
1 Washer fluid reservoir
2 Vehicle identification number
3 Oil filler neck
4 Jump-starting, positive terminal
5 Jump-starting, negative terminal
6 Coolant reservoir
Hood
Safety information
WARNING
Improperly executed work in the engine
compartment can damage vehicle components
and impair vehicle functions. There is a risk of
personal and property damage. The manufac‐
turer of your vehicle recommends that, in the
effort to avoid such risks, work in the engine
compartment be performed by a dealer’s serv‐
ice center or another qualified service center or
repair shop.
◀
Seite 210
MOBILITY
Engine compartment
210
Online Edition for Part no. 01 40 2 915 044 - X/16
WARNING
The engine compartment accommodates
moving components. Certain components in
the engine compartment can also move with
the vehicle switched off, e.g., the radiator fan.
There is a risk of injury. Do not reach into the
area of moving parts. Keep articles of clothing
and hair away from moving parts.◀
WARNING
There are protruding parts, for instance
locking hook, on the inside of the hood. There
is a risk of injury. If the hood is open, pay atten‐
tion to protruding parts and keep clear of these
areas.◀
WARNING
An incorrectly locked hood can open
while driving and restrict visibility. There is a
risk of an accident. Stop immediately and cor‐
rectly close the hood.◀
WARNING
Body parts can be jammed when opening
and closing the hood. There is a risk of injury.
Make sure that the area of movement of the
hood is clear during opening and closing.◀
NOTE
Folded-away wipers can be jammed
when the hood is opened. There is a risk of
property damage. Make sure that the wipers
with the wiper blades mounted are folded
down onto the windshield before opening the
hood.◀
NOTE
When the hood is closed, it must engage
on both sides. Pressing again can damage the
hood. There is a risk of property damage. Open
the hood again and then close it energetically.
Avoid pressing again.
◀
Opening the hood
1. Pull lever, arrow 1.
Hood is unlocked.
2. After the lever is released, pull the lever
again, arrow 2.
Hood can be opened.
Indicator/warning lights
When the hood is opened, a Check Control
message is displayed.
Closing the hood
Let the hood fall from approx. 16 inches/40 cm,
arrow.
The hood must engage on both sides.
Seite 211
Engine compartment
MOBILITY
211
Online Edition for Part no. 01 40 2 915 044 - X/16
Engine oil
Vehicle features and op‐
tions
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your vehicle, e. g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be
observed.
General information
The engine oil consumption is dependent on
the driving style and driving conditions.
Therefore, regularly check the engine oil level
after refueling.
The engine oil consumption can increase in the
following situations, for example:
▷ Sporty driving style.
▷ Break-in of the engine.
▷ Idling of the engine.
▷ With use of engine oil types that are classi‐
fied as not suitable.
The vehicle is equipped with electronic oil
measurement.
The electronic oil measurement has two meas‐
uring principles:
▷ Status display.
▷ Detailed measurement.
Electronic oil measure‐
ment
Status display
The concept
The engine oil level is monitored electronically
while driving and shown on the Control Display.
If the engine oil level reaches the minimum
level, a check control message is displayed.
Functional requirements
A current measured value is available after ap‐
prox. 30 minutes of driving. During a shorter
trip, the status of the last, sufficiently long trip is
displayed.
With frequent short-distance trips, perform a
detailed measurement.
Displaying the engine oil level
Via the onboard monitor:
1. "Vehicle info"
2. "Vehicle status"
3. "Engine oil level"
Engine oil level display messages
Different messages appear on the display de‐
pending on the engine oil level. Pay attention
to these messages.
If the engine oil level is too low within the next
125 miles/200 km, add engine oil, refer to
page 213.
A red indicator light indicates that the
engine oil pressure is too low.
Seite 212
MOBILITY
Engine oil
212
Online Edition for Part no. 01 40 2 915 044 - X/16
NOTE
An engine oil level that is too low causes
engine damage. There is a risk of property
damage. Immediately add engine oil.◀
Take care not to add too much engine oil.
NOTE
Too much engine oil can damage the en‐
gine or the catalytic converter. There is a risk of
property damage. Do not add too much engine
oil. When too much engine oil is added, have oil
level corrected by a dealer’s service center or
another qualified service center or repair
shop.◀
Detailed measurement
The concept
In the detailed measurement the engine oil
level is checked when the vehicle is stationary,
and displayed via a scale.
If the engine oil level reaches the minimum
level, a check control message is displayed.
During the measurement, the idle speed is in‐
creased somewhat.
Functional requirements
▷ Vehicle is parked in a horizontal position.
▷ Manual transmission: shift lever in neutral
position, clutch and accelerator pedals not
depressed.
▷ Steptronic transmission: selector lever in se‐
lector lever position N or P and accelerator
pedal not depressed.
▷ Engine is running and is at operating tem‐
perature.
Performing a detailed measurement
Via the onboard monitor:
1. "Vehicle info"
2. "Vehicle status"
3. "Measure engine oil level"
4. "Start measurement"
The engine oil level is checked and displayed
via a scale.
Time: approx. 1 minute.
Adding engine oil
General information
Only add engine oil when the message is dis‐
played in the instrument cluster. The quantity
to be added is indicated in the message dis‐
played in the instrument cluster.
Switch off the ignition and safely park the vehi‐
cle before engine oil is added.
Safety information
WARNING
Operating materials, e.g., oils, greases,
coolants, fuels, can contain harmful ingredi‐
ents. There is a risk of injuries or danger to life.
Observe the instructions on the containers.
Avoid the contact of articles of clothing, skin or
eyes with operating materials. Do not refill op‐
erating materials into different bottles. Store
operating materials out of reach of children.◀
NOTE
An engine oil level that is too low causes
engine damage. There is a risk of property
damage.
Add engine oil within the next
125 miles/200 km.◀
NOTE
Too much engine oil can damage the en‐
gine or the catalytic converter. There is a risk of
property damage. Do not add too much engine
oil. When too much engine oil is added, have oil
level corrected by a dealer’s service center or
another qualified service center or repair
shop.
◀
Seite 213
Engine oil
MOBILITY
213
Online Edition for Part no. 01 40 2 915 044 - X/16
Overview
The oil filler neck is located in the engine com‐
partment, refer to page 210.
Opening the oil filler neck
1.
Open the hood, refer to page 210.
2. Open the lid counterclockwise, arrow.
3. Add engine oil.
After refilling, perform a detailed measure‐
ment, refer to page 213.
Engine oil types to add
General information
The engine oil quality is critical for the life of the
engine.
Safety information
NOTE
Oil additives can damage the engine.
There is a risk of property damage. Do not use
oil additives.◀
NOTE
Incorrect engine oil can cause malfunc‐
tions in the engine or damage it. There is a risk
of property damage. When selecting an engine
oil, make sure that the engine oil has the cor‐
rect oil rating.
◀
Suitable engine oil types
Add engine oils that meet the following oil rat‐
ing standards:
Gasoline engine
BMW Longlife-01 FE.
More information about suitable engine oil rat‐
ings and viscosities of engine oils can be re‐
quested from a dealer’s service center or an‐
other qualified service center or repair shop.
Alternative engine oil types
If an engine oil suitable for continuous use is
not available, up to 1 US quart/liter of an en‐
gine oil with the following oil rating can be
added:
Gasoline engine
BMW Longlife-01.
API SL or superior oil rating.
Viscosity grades
Gasoline engine:
When selecting an engine oil, make sure that
the engine oil has the viscosity grade SAE
0W-20. Alternatively, also engine oils with vis‐
cosity grades SAE 0W-30, SAE 5W-20, SAE
5W-30, SAE 0W-40 or SAE 5W-40 can be used.
More information about suitable engine oil rat‐
ings and viscosities of engine oils can be re‐
quested from a dealer’s service center or an‐
other qualified service center or repair shop.
Engine oil change
NOTE
Engine oil that is not changed in timely
fashion can cause increased engine wear and
thus engine damage. There is a risk of property
damage. Do not exceed the service data indi‐
cated in the vehicle.
◀
Seite 214
MOBILITY
Engine oil
214
Online Edition for Part no. 01 40 2 915 044 - X/16
The vehicle manufacturer recommends that
you have a dealer’s service center or another
qualified service center or repair shop change
the engine oil.
Seite 215
Engine oil
MOBILITY
215
Online Edition for Part no. 01 40 2 915 044 - X/16
Coolant
Vehicle features and op‐
tions
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your vehicle, e. g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be
observed.
General information
Coolant consists of water and additives.
Not all commercially available additives are
suitable for the vehicle. Information about suit‐
able additives is available from a dealer’s serv‐
ice center or another qualified service center or
repair shop.
Safety information
WARNING
With the engine hot and the cooling sys‐
tem open, coolant can escape and lead to
scalding. There is a risk of injury. Only open the
cooling system with the engine cooled down.◀
WARNING
Additives are harmful and incorrect addi‐
tives can damage the engine. There is a risk of
injury and risk of property damage. Do not al‐
low additives to come into contact with skin,
eyes or articles of clothing. Use suitable addi‐
tives only.
◀
Coolant level
Overview
The coolant reservoir is in the engine compart‐
ment, refer to page 210.
Open the hood, refer to page 210.
Checking
There are yellow Min and Max marks in the
coolant reservoir.
1. Let the engine cool.
2. Turn the lid of the coolant reservoir slightly
counterclockwise to allow any excess pres‐
sure to dissipate, then open it.
3. The coolant level is correct if it lies between
the minimum and maximum marks in the
filler neck.
Seite 216
MOBILITY
Coolant
216
Online Edition for Part no. 01 40 2 915 044 - X/16
Adding
1.
Let the engine cool.
2. Turn the lid of the coolant reservoir slightly
counterclockwise to allow any excess pres‐
sure to dissipate, then open it.
3. If the coolant is low, slowly add coolant up
to the specified level; do not overfill.
4. Close cap.
5. Have the cause of the coolant loss elimi‐
nated as soon as possible.
Disposal
Comply with the relevant environmen‐
tal protection regulations when dispos‐
ing of coolant and coolant additives.
Seite 217
Coolant
MOBILITY
217
Online Edition for Part no. 01 40 2 915 044 - X/16
Maintenance
Vehicle features and op‐
tions
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your vehicle, e. g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be
observed.
MINI maintenance system
The maintenance system indicates required
maintenance measures, and thereby provides
support in maintaining road safety and the op‐
erational reliability of the vehicle.
In some cases, scopes and intervals may vary
according to the country-specific version. Re‐
placement work, spare parts, fuels and lubri‐
cants, and wear materials are calculated sepa‐
rately. Further information is available from a
dealer’s service center or another qualified
service center or repair shop.
Condition Based Service
CBS
Concept
Sensors and special algorithms take into ac‐
count the driving conditions of the vehicle. CBS
uses these to calculate the need for mainte‐
nance.
The system makes it possible to adapt the
amount of maintenance corresponding to your
user profile.
General information
Information on service requirements, refer to
page 86, can be displayed on the Control Dis‐
play.
Service data in the remote control
Information on the required maintenance is
continuously stored in the remote control. The
dealer’s service center can read this data out
and suggest an optimized maintenance scope
for the vehicle.
Therefore, hand the service advisor the remote
control with which the vehicle was driven most
recently.
Storage periods
Storage periods during which the vehicle bat‐
tery was disconnected are not taken into ac‐
count.
If this occurs, have a dealer's service center or
another qualified service center or repair shop
update the time-dependent maintenance pro‐
cedures, such as checking brake fluid and, if
necessary, changing the engine oil and the mi‐
crofilter/activated-charcoal filter.
Service and Warranty In‐
formation Booklet for
US models and Warranty
and Service Guide Book‐
let for Canadian models
Please consult your Service and Warranty Infor‐
mation Booklet for US models and Warranty
and Service Guide Booklet for Canadian models
for additional information on service require‐
ments.
The manufacturer of your vehicle recommends
that maintenance and repair be performed by a
Seite 218
MOBILITY
Maintenance
218
Online Edition for Part no. 01 40 2 915 044 - X/16
dealer’s service center or another qualified
service center or repair shop. Records of regu‐
lar maintenance and repair work should be re‐
tained.
Socket for OBD Onboard
Diagnosis
Safety information
NOTE
The socket for Onboard Diagnosis is an
intricate component intended to be used in
conjunction with specialized equipment to
check the vehicle’s primary emissions system.
Improper use of the socket for Onboard Diag‐
nosis, or contact with the socket for Onboard
Diagnosis for other than its intended purpose,
can cause vehicle malfunctions and creates
risks of personal and property damage. Given
the foregoing, the manufacture of your vehicle
strongly recommends that access to the socket
for Onboard Diagnosis be limited to a dealer's
service center or another qualified service cen‐
ter or repair shop or other persons that have
the specialized training and equipment for pur‐
poses of properly utilizing the socket for On‐
board Diagnosis.◀
Position
There is an OBD socket on the driver's side for
checking the primary components in the vehi‐
cle's emissions.
Emissions
▷
The warning lamp lights up:
Emissions are deteriorating. Have
the vehicle checked as soon as pos‐
sible.
▷ The warning lamp flashes under certain cir‐
cumstances:
This indicates that there is excessive misfir‐
ing in the engine.
Reduce the vehicle speed and have the sys‐
tem checked immediately; otherwise, seri‐
ous engine misfiring within a brief period
can seriously damage emission control
components, in particular the catalytic con‐
verter.
Seite 219
Maintenance
MOBILITY
219
Online Edition for Part no. 01 40 2 915 044 - X/16
Replacing components
Vehicle features and op‐
tions
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your vehicle, e. g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be
observed.
Onboard vehicle tool kit
Depending on the vehicle equipment, the on‐
board vehicle tool kit is located on the right
side under the cargo area floor or in a bag on
the right side of the cargo area.
After use, secure the bag for the onboard vehi‐
cle tool kit on a lashing eye again.
Wiper blade replacement
Safety information
NOTE
If the wiper arm falls onto the windshield
without the wiper blades installed, the wind‐
shield can be damaged. There is a risk of prop‐
erty damage. Secure the wiper arm when re‐
placing the wiper blades and do not fold down
the wipers without the wiper blades installed.◀
NOTE
Folded-away wipers can be jammed
when the hood is opened. There is a risk of
property damage. Make sure that the wipers
with the wiper blades mounted are folded
down onto the windshield before opening the
hood.◀
Front wiper blades
1.
To change the wiper blades, fold up the
wiper arms.
2. Fold up and hold the wiper arm firmly.
3. Open the wiper blade lock, arrow.
4. Pull the wiper blade down out of the holder
on the wiper arm, arrow 1.
5. Pull the wiper blade free from the holder of
the wiper arm, arrow 2.
Seite 220
MOBILITY
Replacing components
220
Online Edition for Part no. 01 40 2 915 044 - X/16
6. Insert and latch a new wiper blade in re‐
verse order.
7. Fold down the wiper arm.
Rear wiper blade
1.
Fold up and hold the wiper arm firmly.
2. Turn the wiper blade all the way back.
3. Push the wiper blade out of the fastening
by continuing to turn it all the way.
4. Insert the new wiper blade by following the
steps in reverse order. The wiper blade
must engage audibly.
5. Fold down the wiper arm.
Light/bulb replacement
General information
Lights and bulbs
Lights and bulbs make an essential contribution
to vehicle safety.
The manufacturer of the vehicle recommends
that you have appropriate work performed by a
dealer’s service center or another qualified
service center or repair shop if you are unfami‐
liar with it or if it has not been described here.
A spare lamp box is available from a dealer’s
service center or another qualified service cen‐
ter or repair shop.
Observe the safety information, refer to
page
221.
Light-emitting diodes (LEDs)
Some items of equipment use light-emitting di‐
odes installed behind a cover as a light source.
These light-emitting diodes are related to con‐
ventional lasers and are officially designated as
Class 1 light-emitting diodes.
Observe the safety information, refer to
page 221.
Safety information
Lights and bulbs
WARNING
Bulbs can get hot during operation. Con‐
tact with the bulbs can cause burns. There is a
risk of injury. Only change bulbs after they have
cooled off.◀
WARNING
Work on switched-on lighting systems
can cause short circuits. There is a risk of injury
or risk of property damage. When working on
the lighting system, switch off the lamps in
question. If necessary, heed the bulb manufac‐
turer's instructions.◀
NOTE
Dirty bulbs have a reduced service life.
There is a risk of property damage. Do not hold
new bulbs with your bare hands. Use a clean
cloth or something similar, or hold the bulb by
its base.◀
Light-emitting diodes (LEDs)
WARNING
Too intensive brightness can irritate or
damage the retina of the eye. There is a risk of
injury. Do not look directly into the headlights
or other light sources. Do not remove the LED
covers.
◀
Seite 221
Replacing components
MOBILITY
221
Online Edition for Part no. 01 40 2 915 044 - X/16
Headlight glass
Condensation can form on the inside of the ex‐
ternal lights in cool or humid weather. When
driving with the lights switched on, the conden‐
sation evaporates after a short time. The head‐
light glass does not need to be changed.
If despite driving with the lights switched on,
increasing humidity forms, e. g. water droplets
in the lamp, the manufacturer of your vehicle
recommends having it checked by a dealer’s
service center or another qualified service cen‐
ter or repair shop.
Headlight setting
The headlight adjustments can be affected by
changing lights and bulbs. After the headlight
adjustment was changed, have it checked and,
if necessary, corrected by a dealer’s service
center or another qualified service center or re‐
pair shop.
Front halogen lights, bulb replacement
Overview
Halogen headlights
1 Low beams/high beams
2 Turn signal
Bug light
1 Parking lights
2 Daytime running lights
3 Fog lights
Low beams/high beams
Follow the general instructions on lights and
bulbs, refer to page 221.
Bulbs: H4
1. Open the hood, refer to page 211.
2. Turn the lid counterclockwise, arrow, and
remove.
3. Pull off the connector.
4. Unclip spring clip, arrow, and fold down.
Seite 222
MOBILITY
Replacing components
222
Online Edition for Part no. 01 40 2 915 044 - X/16
5. Remove the bulb from the headlight hous‐
ing.
6. Insert the new bulb and install the cover in
the reverse order.
Turn signal
Follow the general instructions on lights and
bulbs, refer to page 221.
Bulbs: PW24W
With white turn signal lights: PWY24W
1. Turn the steering wheel.
2. Turn the lid counterclockwise, arrow 1, and
remove.
3. Unscrew the inner lid counterclockwise,
and remove it.
4. Pull bulb holder out of the bulb housing; if
needed, loosen it with small tilting move‐
ments if possible.
5. Pull the bulb out of the fixture.
6. Insert the new bulb and install the cover in
the reverse order.
Parking lights/fog lights/daytime
running lights
Follow the general instructions on lights and
bulbs, refer to page 221.
Bulbs:
▷ Parking lights for halogen headlights: W5W
Parking lights for LED headlights:
W5W NBV.
▷ Daytime running light: PSX24W.
▷ Fog light: H8.
Replacing the bulbs
1. Turn the steering wheel.
2. Turn the lid counterclockwise, arrow 2, and
remove.
3. Pull off the connector.
4. Remove the bulb holder.
Seite 223
Replacing components
MOBILITY
223
Online Edition for Part no. 01 40 2 915 044 - X/16
▷ Parking lights: turn the bulb holder, ar‐
row 1, counterclockwise and remove.
▷ Daytime running lights: squeeze the
upper and lower locks of the bulb
holder, arrow 2, and remove the bulb
holder.
For better accessibility, remove the bulb
of the fog light as needed.
▷ Fog lights: turn the bulb holder, ar‐
row 3, counterclockwise and remove.
5. Pull the bulb out of the fixture.
6. Insert the new bulb and install the cover in
the reverse order.
The daytime running lights bulb holder en‐
gages audibly, first below, then above.
LED front lights, bulb replacement
General information
The following lights feature LED technology:
▷ Daytime running lights
▷ High beams
▷ Low beams
▷ Parking lights
▷ Fog lights
In the case of a malfunction, contact a dealer’s
service center or another qualified service cen‐
ter or repair shop.
Overview
Position of the headlights
1 Daytime running lights
2 Low beams/high beams
3 Turn signal
LED bug light
1 Parking lights
2 Fog lights
Turn signal
Follow the general instructions on lights and
bulbs, refer to page 221.
Bulbs: PW24W
Seite 224
MOBILITY
Replacing components
224
Online Edition for Part no. 01 40 2 915 044 - X/16
With white turn signal lights: PWY24W
1. Turn the steering wheel.
2. Turn the lid counterclockwise, arrow 1, and
remove.
3. Unscrew the inner lid counterclockwise,
and remove it.
4. Pull bulb holder out of the bulb housing; if
needed, loosen it with small tilting move‐
ments if possible.
5. Pull the bulb out of the fixture.
6. Insert the new bulb and install the cover in
the reverse order.
Tail lights, bulb replacement
Overview
Vehicles with a rear fog lamp
1 Side tail lamps
2 Rear fog lamp
3 License plate lamp
4 Center brake lamp
Vehicle with two rear fog lights
1 Side tail lamps
2 Rear fog lights
3 License plate lamp
4 Center brake lamp
Seite 225
Replacing components
MOBILITY
225
Online Edition for Part no. 01 40 2 915 044 - X/16
Side tail lamps
1 Brake lights/tail lamps
2 Turn signal
3 Reversing lights
Side LED tail lights
1 Tail lamps
2 Turn signal
3 Brake light
4 Reversing lights
Side tail lights
Follow the general instructions on lights and
bulbs, refer to page 221.
Bulbs: P21W
1. Open the tailgate.
2. Remove left or right cover.
3. Through the opening, loosen the plug con‐
nector, arrow 2 on the bulb holder.
Press the latches together, arrows 1, and
remove the bulb holder.
4. Remove the bulb holder from the opening.
5. Press the nonworking bulb gently into the
socket, turn counterclockwise and remove.
▷ Arrow 1: brake lights/tail lights.
▷ Arrow 2: turn signal.
Seite 226
MOBILITY
Replacing components
226
Online Edition for Part no. 01 40 2 915 044 - X/16
▷ Arrow 3: reversing light.
6. Proceed in the reverse order to insert the
new bulb and attach the bulb holder. Make
sure that the bulb holder engages in all fas‐
teners.
Central brake lamp and license plate
lamp
Follow the general instructions on lights and
bulbs, refer to page 221.
The lights feature LED technology. In the case
of a malfunction, contact a dealer’s service cen‐
ter or another qualified service center or repair
shop.
Vehicles with a rear fog lamp
Follow the general instructions on lights and
bulbs, refer to page 221.
Bulbs: W16W
1. On vehicles with heat shield:
Loosen 3 screws, arrow.
2. Push the heat shield forward and the
bumper back in order to be able to reach
the fog lamp.
3. Turn the bulb socket counterclockwise and
remove.
The wire is long enough to guide the socket
down and through between any heat shield
that may be installed and the bumper.
4. Replace nonworking bulb.
5. To install the new bulb, proceed in reverse
order of removal.
Vehicle with two rear fog lights
Follow the general instructions on lights and
bulbs, refer to page 221.
Bulbs: W16W
Left rear fog lamp:
1. On vehicles with heat shield:
Loosen 3 screws, arrow.
2. Push the heat shield forward and the
bumper back in order to be able to reach
the fog lamp.
3. Turn the bulb socket counterclockwise and
remove.
Seite 227
Replacing components
MOBILITY
227
Online Edition for Part no. 01 40 2 915 044 - X/16
The wire is long enough to guide the socket
down and through between any heat shield
that may be installed and the bumper.
4. Replace nonworking bulb.
5. To install the new bulb, proceed in reverse
order of removal.
Right fog lamp:
1. Turn the bulb socket counterclockwise and
remove.
The wire is long enough to guide the socket
down and through between any heat shield
that may be installed and the bumper.
2. Replace nonworking bulb.
3. To install the new bulb, proceed in reverse
order of removal.
Side turn signal, bulb replacement
Follow the general instructions on lights and
bulbs, refer to page 221.
Bulbs:
▷ With orange lens: W5W.
▷ With white lens: WY5W.
1. Open the hood. The covers of the side turn
signal lights are on the left and right next to
the hinges of the hood.
2. Loosen nuts of the cover by hand and re‐
move the cover.
3. Turn the bulb socket counterclockwise and
remove.
4. Replace the bulb.
5. To insert the new bulb, proceed in reverse
order of removal. Insert the nuts of the
cover and press down.
Seite 228
MOBILITY
Replacing components
228
Online Edition for Part no. 01 40 2 915 044 - X/16
Vehicle battery
Maintenance
The battery is maintenance-free.
The added amount of acid is sufficient for the
service life of the battery.
More information about the battery can be re‐
quested from a dealer’s service center or an‐
other qualified service center or repair shop.
Replacing the vehicle battery
General information
After a battery replacement, the manufacturer
of your vehicle recommends that the vehicle
battery be registered on the vehicle by a deal‐
er’s service center or another qualified service
center or repair shop to ensure that all comfort
features are fully available and that any Check
Control messages of these comfort features are
no longer displayed.
Safety information
NOTE
Vehicle batteries that are not compatible
can damage vehicle systems and impair vehicle
functions. There is a risk of personal and prop‐
erty damage. Only vehicle batteries that are
compatible with your vehicle type should be in‐
stalled in your vehicle. Information on compati‐
ble vehicle batteries is available at your dealer’s
service center.◀
Charging the battery
General information
Make sure that the battery is always sufficiently
charged to guarantee that the battery remains
usable for its full service life.
A red indicator lamp is displayed when
the battery is discharged.
The battery may need to be charged in the fol‐
lowing cases:
▷ When making frequent short-distance
drives.
▷ If the vehicle is not used for more than a
month.
▷ Steptronic transmission: when parked for
long periods of time in selector lever posi‐
tion D, R or N.
Safety information
NOTE
Battery chargers for the vehicle battery
can work with high voltages and currents,
which means that the 12 volt on-board net‐
work can be overloaded or damaged. There is a
risk of property damage. Only connect battery
chargers for the vehicle battery to the starting
aid terminals in the engine compartment.◀
Starting aid terminals
In the vehicle, only charge the battery via the
starting aid terminals, refer to page 232, in the
engine compartment with the engine off.
Power failure
After a power loss, some equipment needs to
be newly initialized or individual settings up‐
dated, for example:
▷ Time: update.
▷ Date: update.
▷ Glass sunroof: initialize the system.
Disposing of old batteries
Have old batteries disposed of by a
dealer’s service center or another quali‐
fied service center or repair shop or
take them to a collection point.
Maintain the battery in an upright position for
transport and storage. Secure the battery so
that it does not tip over during transport.
Seite 229
Replacing components
MOBILITY
229
Online Edition for Part no. 01 40 2 915 044 - X/16
Fuses
Safety information
WARNING
Incorrect and repaired fuses can overload
electrical lines and components. There is a risk
of fire. Never attempt to repair a blown fuse.
Do not replace a nonworking fuse with a sub‐
stitute of another color or amperage rating.◀
Replacing a fuse
The fuses are located in the passenger floor
area under the dashboard.
Plastic tweezers and information on the fuse
types and locations are stored in the fuse box.
1. To open, loosen screws, arrow 1.
2. Fold down the fuse holder, arrow 2.
3. Replace the fuse in question.
4. The installation is done in reverse order
from the removal.
Seite 230
MOBILITY
Replacing components
230
Online Edition for Part no. 01 40 2 915 044 - X/16
Breakdown assistance
Vehicle features and op‐
tions
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your vehicle, e. g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be
observed.
Hazard warning flash‐
ers
The button is located above the Control Dis‐
play.
The red light in the button flashes when the
hazard warning flashers are activated.
Roadside Assistance
Service availability
Roadside Assistance can be reached around the
clock in many countries. You can obtain assis‐
tance there in the event of a vehicle break‐
down.
Roadside Assistance
The Roadside Assistance phone number can be
viewed on the onboard monitor or a connec‐
tion to Roadside Assistance can be established
directly.
Warning triangle
The warning triangle is located in the tailgate.
To remove, loosen the brackets.
First-aid kit
The first-aid kit is located in the cargo area.
Some of the articles have a limited service life.
Check the expiration dates of the contents reg‐
ularly and replace any expired items promptly.
Jump-starting
General information
If the battery is discharged, the engine can be
started using the battery of another vehicle and
two jumper cables. Only use jumper cables with
fully insulated clamp handles.
Seite 231
Breakdown assistance
MOBILITY
231
Online Edition for Part no. 01 40 2 915 044 - X/16
Safety information
DANGER
Contact with live components can lead to
an electric shock. There is a risk of injuries or
danger to life. Do not touch any components
that are under voltage.◀
Preparation
NOTE
In the case of body contact between the
two vehicles, a short circuit can occur during
jump-starting. There is a risk of property dam‐
age. Make sure that no body contact occurs.◀
1. Check whether the battery of the other ve‐
hicle has a voltage of 12 volts. The voltage
information can be found on the battery.
2. Switch off the engine of the assisting vehi‐
cle.
3. Switch off any electronic systems/power
consumers in both vehicles.
Starting aid terminals
WARNING
If the jumper cables are connected in the
incorrect order, sparking may occur. There is a
risk of injury. Pay attention to the correct order
during connection.◀
The starting aid terminal in the engine com‐
partment acts as the battery's positive terminal.
Open the cover of the starting aid terminal.
The body ground or a special nut acts as the
battery negative terminal.
Connecting the cables
1.
Pull off the lid of the starting aid terminal.
2. Attach one terminal clamp of the positive
jumper cable to the positive terminal of the
battery, or to the corresponding starting aid
terminal of the vehicle providing assistance.
3. Attach the terminal clamp on the other end
of the cable to the positive terminal of the
battery, or to the corresponding starting aid
terminal of the vehicle to be started.
4. Attach one terminal clamp of the negative
jumper cable to the negative terminal of
the battery, or to the corresponding engine
or body ground of assisting vehicle.
5. Attach the second terminal clamp to the
negative terminal of the battery, or to the
corresponding engine or body ground of
the vehicle to be started.
Starting the engine
Never use spray fluids to start the engine.
1. Start the engine of the assisting vehicle and
let it run for several minutes at an increased
idle speed.
If the vehicle to be started has a diesel en‐
gine: let the engine of the assisting vehicle
run for approx. 10 minutes.
2. Start the engine of the vehicle that is to be
started in the usual way.
Seite 232
MOBILITY
Breakdown assistance
232
Online Edition for Part no. 01 40 2 915 044 - X/16
If the first starting attempt is not successful,
wait a few minutes before making another
attempt in order to allow the discharged
battery to recharge.
3. Let both engines run for several minutes.
4. Disconnect the jumper cables in the reverse
order.
Check the battery and recharge, if needed.
Tow-starting and towing
Safety information
WARNING
Due to system limits, individual functions
can malfunction during tow-starting/towing
with the Intelligent Safety systems activated,
e.g., approach control warning with light brak‐
ing function. There is a risk of an accident.
Switch all Intelligent Safety systems off prior to
tow-starting/towing.◀
Steptronic transmission with driven
front axle: transporting the vehicle
General information
The vehicle must not be towed if the front
wheels are touching the ground.
Safety information
NOTE
The vehicle can be damaged when tow‐
ing the vehicle with a lifted rear axle. There is a
risk of property damage. Have vehicle trans‐
ported only with lifted front axle or on a load‐
ing platform.◀
Tow truck
Your vehicle should be transported with a tow
truck with a so-called lift bar or on a flat bed.
NOTE
When lifting the vehicle by the tow fitting
or body and chassis parts; damage can occur
on vehicle parts. There is a risk of property
damage. Lift vehicle using suitable means.◀
Pushing the vehicle
To remove a disabled vehicle from the danger
area, it can be pushed for a short distance. The
vehicle can only be pushed in selector lever po‐
sition N.
In order to ensure that the vehicle can roll, pro‐
ceed as follows:
1. Switch on the ignition.
2. Depress brake pedal.
3. Engage selector lever position N.
If there is a malfunction, you may not be able
to change the selector lever position.
Manually unlock the transmission lock, refer to
page 78, if needed.
Manual transmission
Observe before towing your vehicle
Gearshift lever in neutral position.
Seite 233
Breakdown assistance
MOBILITY
233
Online Edition for Part no. 01 40 2 915 044 - X/16
Towing
NOTE
If manual unlocking of the parking brake
is not possible, the vehicle cannot be moved or
towed. There is a risk of property damage. The
vehicle should only be transported on a loading
platform.◀
Information the following instructions:
▷ Make sure that the ignition is switched on;
otherwise, the low beams, tail lamps, turn
signals, and wipers may be unavailable.
▷ Do not tow the vehicle with the rear axle
tilted, as the front wheels could turn.
▷ When the engine is stopped, there is no
power assist. Consequently, more force
needs to be applied when braking and
steering.
▷ Larger steering wheel movements are re‐
quired.
▷ The towing vehicle must not be lighter than
the vehicle being towed; otherwise, it will
not be possible to control the vehicle's re‐
sponse.
▷ Do not exceed a towing speed of
30 mph/50 km/h.
▷ Do not exceed a towing distance of
30 miles/50 km.
Tow truck
With driven front axle
Have your vehicle transported with a tow truck
with a so-called lift bar or on a flat bed.
NOTE
When lifting the vehicle by the tow fitting
or body and chassis parts; damage can occur
on vehicle parts. There is a risk of property
damage. Lift vehicle using suitable means.◀
Towing other vehicles
General information
Switch on the hazard warning system, depend‐
ing on local regulations.
If the electrical system has failed, clearly iden‐
tify the vehicle being towed by placing a sign or
a warning triangle in the rear window.
Safety information
WARNING
If the approved gross vehicle weight of
the towing vehicle is lighter than the vehicle to
be towed, the tow fitting can tear off or it will
not be possible to control the vehicle's re‐
sponse. There is a risk of an accident! Make
sure that the gross vehicle weight of the towing
vehicle is heavier than the vehicle to be
towed.◀
NOTE
If the tow bar or tow rope is attached in‐
correctly, damage to other vehicle parts can oc‐
cur. There is a risk of property damage. Cor‐
rectly attach the tow bar or tow rope to the tow
fitting.◀
Tow bar
The tow fittings used should be on the same
side on both vehicles.
Should it prove impossible to avoid mounting
the tow bar at an offset angle, please observe
the following:
▷ Maneuvering capability is limited going
around corners.
▷ The tow bar will generate lateral forces if it
is secured with an offset.
Seite 234
MOBILITY
Breakdown assistance
234
Online Edition for Part no. 01 40 2 915 044 - X/16
Tow rope
When starting to tow the vehicle, make sure
that the tow rope is taut.
To avoid jerking and the associated stresses on
the vehicle components when towing, always
use nylon ropes or nylon straps.
NOTE
If the tow bar or tow rope is attached in‐
correctly, damage to other vehicle parts can oc‐
cur. There is a risk of property damage. Cor‐
rectly attach the tow bar or tow rope to the tow
fitting.◀
Tow fitting
General information
The screw-in tow fitting should always be car‐
ried in the vehicle.
The tow fitting can be screwed in at the front or
rear of the vehicle.
The tow fitting and the onboard vehicle tool kit,
refer to page 220, are together in the cargo
area.
Use of the tow fitting:
▷ Use only the tow fitting provided with the
vehicle and screw it all the way in.
▷ Use the tow fitting for towing on paved
roads only.
▷ Avoid lateral loading of the tow fitting, for
instance do not lift the vehicle by the tow
fitting.
Safety information
NOTE
If the tow fitting is not used as intended,
there can be damage to the vehicle or to the
tow fitting. There is a risk of property damage.
Observe the notes on using the tow fitting.◀
Screw thread for tow fitting
Threaded holes for the tow fitting are located in
the front and rear of the vehicle on the right
side with respect to the direction of travel.
Press on the mark on the edge of the cover to
push it out.
Tow-starting
Steptronic transmission
Do not tow-start the vehicle.
Tow-starting the engine is not possible due to
the Steptronic transmission.
Have the reasons for the starting difficulties
corrected by a dealer’s service center or an‐
other qualified service center or repair shop.
Manual transmission
If possible, do not tow-start the vehicle but
start the engine by jump-starting, refer to
page 231. If the vehicle is equipped with a cat‐
alytic converter, only tow-start while the engine
is cold.
1. Switch on the hazard warning system and
comply with local regulations.
2. Switch on the ignition, refer to page 65.
Seite 235
Breakdown assistance
MOBILITY
235
Online Edition for Part no. 01 40 2 915 044 - X/16
3. Engage third gear.
4. Have the vehicle tow-started with the
clutch pedal pressed and slowly release the
pedal. After the engine starts, immediately
press on the clutch pedal again.
5. Stop at a suitable location, remove the tow
bar or rope, and switch off the hazard
warning system.
6. Have the vehicle checked by a dealer’s
service center or another qualified service
center or repair shop.
Seite 236
MOBILITY
Breakdown assistance
236
Online Edition for Part no. 01 40 2 915 044 - X/16
Care
Vehicle features and op‐
tions
This chapter describes all standard, country-
specific and optional features offered with the
series. It also describes features that are not
necessarily available in your vehicle, e. g., due
to the selected options or country versions. This
also applies to safety-related functions and sys‐
tems. When using these functions and systems,
the applicable laws and regulations must be
observed.
Vehicle washes
General information
Regularly remove foreign objects such as leaves
in the area below the windshield when the
hood is raised.
Wash your vehicle frequently, particularly in
winter. Intense soiling and road salt can dam‐
age the vehicle.
Steam jets or high-pressure washers
Safety information
NOTE
When cleaning with high-pressure wash‐
ers, components can be damaged due to the
pressure or temperatures being too high. There
is a risk of property damage. Maintain sufficient
distance and do not spray too long continu‐
ously. Follow the operating instructions for the
high-pressure washer.◀
Distances and temperature
▷ Maximum temperature: 140 ℉/60 ℃.
▷ Minimum distance from sensors, cameras,
seals: 12 inches/30 cm.
▷ Minimum distance from glass sunroof:
31.5 inches/80 cm.
Automatic vehicle washes
Safety information
NOTE
Water can penetrate in the windshield
area due to high-pressure washers. There is a
risk of property damage. Avoid high-pressure
washers.◀
NOTE
Improper use of automatic vehicle
washes can cause damage to the vehicle. There
is a risk of damage to property. Follow the fol‐
lowing instructions:
▷ Give preference to cloth vehicle washes or
those that use soft brushes in order to
avoid paint damage.
▷ Avoid vehicle washes with guide rails
higher than 4 in/10 cm to avoid damage to
the chassis.
▷ Observe the tire width of the guide rail to
avoid damage to tires and rims.
▷ Fold in exterior mirrors to avoid damage to
the exterior mirrors.
▷ Unscrew the rod antenna to avoid the rod
antenna breaking off.
▷ Deactivate the wiper and, if necessary, rain
sensor to avoid damage to the wiper sys‐
tem.◀
Before driving into a vehicle wash
In order to ensure that the vehicle can roll in a
vehicle wash, take the following steps:
Manual transmission:
1. Drive into the vehicle wash.
2. Shift to neutral.
Seite 237
Care
MOBILITY
237
Online Edition for Part no. 01 40 2 915 044 - X/16
3. Switch the engine off.
Steptronic transmission:
1. Drive into the vehicle wash.
2. Engage selector lever position N.
3. Make sure that the parking brake is re‐
leased.
4. Switch the engine off.
In this way, the ignition remains switched
on, and two Check-Control messages are
displayed.
Some vehicle washes do not permit persons in
the vehicle. The vehicle cannot be locked from
the outside when in selector lever position N. A
signal is sounded when an attempt is made to
lock the vehicle.
Driving out of a vehicle wash
To start the engine with manual transmission:
1. Ensure that the vehicle key is in the car.
2. Press on the clutch pedal.
3. Press the Start/Stop button.
To start the engine with Steptronic transmis‐
sion:
1. Ensure that the vehicle key is in the car.
2. Depress the brake pedal.
3. Press the Start/Stop button.
Headlights
Do not rub the headlights dry and do not use
abrasive or acidic cleaning agents.
Soak areas that have been dirtied, for instance
from insects, with shampoo and wash off with
water.
Thaw ice with de-icing spray; do not use an ice
scraper.
After washing the vehicle
After washing the vehicle, apply the brakes
briefly to dry them; otherwise, braking action
can be reduced. The heat generated when
braking helps to dry the brake discs and pads
and protect them from corrosion.
Completely remove all residues on the win‐
dows, to minimize loss of visibility due to
smearing and to reduce wiper noises and wiper
blade wear.
Vehicle care
Vehicle care products
General information
MINI recommends using vehicle care and
cleaning products from MINI. Suitable care
products are available from a dealer’s service
center or another qualified service center or re‐
pair shop.
Safety information
WARNING
Cleansers can contain substances that are
dangerous and harmful to your health. There is
a risk of injury. When cleaning the interior,
open the doors or windows. Only use products
intended for cleaning vehicles. Follow the in‐
structions on the container.◀
Vehicle paint
Regular care contributes to driving safety and
value retention. Environmental influences in
areas with elevated air pollution or natural con‐
taminants, such as tree resin or pollen can af‐
fect the vehicle's paintwork. Tailor the fre‐
quency and extent of your vehicle care to these
influences.
Aggressive substances such as spilled fuel, oil,
grease or bird droppings, must be removed im‐
mediately to prevent the finish from being al‐
tered or discolored.
Seite 238
MOBILITY
Care
238
Online Edition for Part no. 01 40 2 915 044 - X/16
Leather care
Remove dust from the leather regularly, using a
cloth or vacuum cleaner.
Otherwise, particles of dust and road grime
chafe in pores and folds, and lead to increased
wear and premature degradation of the leather
surface.
To guard against discoloration, such as from
clothing, clean leather and provide leather care
roughly every two months.
Clean light-colored leather more frequently be‐
cause soiling on such surfaces is substantially
more visible.
Use leather care products; otherwise, dirt and
grease will gradually break down the protective
layer of the leather surface.
Upholstery material care
General information
Vacuum the upholstery regularly with a vac‐
uum cleaner.
If upholstery is very dirty, for instance with bev‐
erage stains, use a soft sponge or microfiber
cloth with a suitable interior cleaner.
Clean the upholstery down to the seams using
large sweeping motions. Avoid rubbing the ma‐
terial vigorously.
Safety information
NOTE
Open Velcro® fasteners on articles of
clothing can damage the seat covers. There is a
risk of property damage. Ensure that any Vel‐
cro® fasteners are closed.◀
Caring for special components
Light-alloy wheels
When cleaning the vehicle, use only neutral
wheel cleaners having a pH value from 5 to 9.
Do not use abrasive cleaning agents or steam
jets above 140 ℉/60 ℃. Follow the manufac‐
turer's instructions.
Aggressive, acidic or alkaline cleaning agents
can destroy the protective layer of adjacent
components, such as the brake disk.
After cleaning, apply the brakes briefly to dry
them. The heat generated during braking dries
brake discs and brake pads and protects them
against corrosion.
Chrome surfaces
Carefully clean components such as the radia‐
tor grille or door handles with an ample supply
of water, possibly with shampoo added, partic‐
ularly when they have been exposed to road
salt.
Rubber components
Environmental influences can cause surface
soiling of rubber parts and a loss of gloss. Use
only water and suitable cleaning agents for
cleaning.
Treat especially worn rubber parts with rubber
care agents at regular intervals. When cleaning
rubber seals, do not use any silicon-containing
vehicle care products in order to avoid damage
or noises.
Fine wood parts
Clean fine wood facing and fine wood compo‐
nents only with a moist rag. Then dry with a
soft cloth.
Plastic components
NOTE
Cleansers that contain alcohol or solvents,
such as lacquer thinners, heavy-duty grease re‐
movers, fuel, or such, can damage plastic parts.
There is a risk of property damage. Clean with a
microfiber cloth. Dampen cloth lightly with wa‐
ter.
◀
Plastic components are e. g:
▷ Imitation leather surfaces.
Seite 239
Care
MOBILITY
239
Online Edition for Part no. 01 40 2 915 044 - X/16
▷ Roofliner.
▷ Lamp lenses.
▷ Instrument cluster cover.
▷ Matt black spray-coated components.
▷ Painted parts in the interior.
Clean with a microfiber cloth.
Dampen cloth lightly with water.
Do not soak the roofliner.
Safety belts
WARNING
Chemical cleansers can destroy the safety
belt webbing. Missing protective effect of the
safety belts. There is a risk of injuries or danger
to life. Use only a mild soapy solution for clean‐
ing the safety belts.◀
Dirty belt straps impede the reeling action and
thus have a negative impact on safety.
Use only a mild soapy solution, with the safety
belts clipped into their buckles.
Do not allow the switchs to retract the safety
belts until they are dry.
Carpets and floor mats
WARNING
Objects in the driver's floor area can limit
the pedal distance or block a depressed pedal.
There is a risk of an accident. Stow objects in
the vehicle such that they are secured and can‐
not enter into the driver's floor area. Use floor
mats that are suitable for the vehicle and can
be safely attached to the floor. Do not use
loose floor mats and do not layer several floor
mats. Make sure that there is sufficient clear‐
ance for the pedals. Ensure that the floor mats
are securely fastened again after they were re‐
moved, e.g., for cleaning.
◀
Floor mats can be removed from the vehicle's
interior for cleaning.
If the floor carpets are very dirty, clean with a
microfiber cloth and water or a textile cleaner.
To prevent matting of the carpet, rub back and
forth in the direction of travel only.
Trailer hitch with removable ball
Keep the ball head and receptacle clean.
Regularly grease or oil bearings, sliding surfaces
and the small balls on the holding pin with
resin-free greases or oils.
Before using steam cleaners or high pressure
cleaners on the vehicle, remove the ball head
and attach the cover to the receptacle.
Do not clean the ball head with a steam cleaner
or high pressure cleaner.
Sensor/camera lenses
To clean sensors and camera lenses, use a cloth
moistened with a small amount of glass deter‐
gent.
Displays/Screens/Projection lenses
NOTE
Chemical cleansers, moisture or fluids of
any kind can damage the surface of displays
and screens. There is a risk of property dam‐
age. Clean with a clean, antistatic microfiber
cloth.◀
NOTE
The surface of displays can be damaged
with improper cleaning. There is a risk of prop‐
erty damage. Avoid pressure that is too high
and do not use any scratching materials.◀
Clean with a clean, antistatic microfiber cloth.
For stubborn soiling on the projection lens of
the Head-up Display, dampen the microfiber
cloth with alcohol. Extending projection lens,
refer to page 95.
Long-term
When the vehicle is shut down for longer than
three months, special measures must be taken.
Further information is available from a dealer’s
Seite 240
MOBILITY
Care
240
Online Edition for Part no. 01 40 2 915 044 - X/16
service center or another qualified service cen‐
ter or repair shop.
Seite 241
Care
MOBILITY
241
Online Edition for Part no. 01 40 2 915 044 - X/16

Related Topics

Refueling Fuel Wheels and tires Engine compartment Engine oil Coolant Maintenance Replacing components Breakdown assistance Care

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot