Get Instruments and controls -> Headlight and turn signal switch Guide for Nissan Leaf 4 Door Second Generation (2018-2025)

HEADLIGHT AND TURN SIGNAL

SWITCH

To turn the autolight system off, turn the

switch to the OFF, or position.

The autolight system can turn on the

headlights and tail lights automatically

when it is dark and turn off the headlights

when it is light.

For US models: The headlights and tail

lights will also be turned on automatically

at twilight or in rainy weather (when the

windshield wiper is operated continuously).

If the power switch is placed in the OFF

position and one of the doors is opened

and this condition continues, the head-

lights remain on for 45 seconds.

SIC3668

SIC3669

Automatic headlights off delay

HEADLIGHT SWITCH

Autolight system

The autolight system allows the headlights

and tail lights to be set so they turn on and

off automatically.

You can keep the headlights on for up to

180 seconds after you push the power

switch to OFF and open any door then

close all the doors.

Lighting

1

᭺

Rotate the switch to the

the front parking, tail, license plate, and

instrument panel lights come on.

position,

To set the autolight system:

You can adjust the period of the automatic

headlights off delay from 0 seconds (OFF)

to 180 seconds. The factory default setting

is 45 seconds.

1. Make sure the headlight switch is in the

2

᭺

Rotate the switch to the

the headlights come on and all the

other lights remain on.

position,

1

AUTO position

.

O

2. Place the power switch in the ON

position.

3. The autolight system automatically

turns the headlights and tail lights on

and off.

Instruments and controls 2-49

NOTE:

For additional information on adjusting

the automatic headlights off delay, refer

to “Vehicle information display” in this

section.

SAA1232

SIC3670

Be sure not to put anything on top of the

1

Headlight beam select

photo sensor

located on the top of

O

1

᭺

To select the low beam, have the lever

in the neutral position as shown and

rotate the switch to the desired posi-

tion. For additional information, refer to

“Headlight switch” in this section.

the instrument panel. The photo sensor

controls the autolight; if it is covered, the

photo sensor reacts as if it is dark and

the headlights will illuminate.

2

᭺

To select the high beam, push the lever

forward while the switch is in the

position. The high beams will come on

and the high beam indicator (blue)

will illuminate. Pull it back to return to

the low beam.

2-50 Instruments and controls

3

᭺

Pulling the lever toward you will flash

the headlight high beam even when

the headlight switch is in the OFF

position.

–

During bad weather (rain, fog,

snow, wind, etc.).

–

When the vehicle is leaning at an

angle due to a punctured tire, be-

ing towed, etc.

When a light source similar to a

headlight or tail light is in the vi-

cinity of the vehicle.

•

The timing of switching the low

beam and high beam may change

under the following situations.

High Beam Assist

–

When the headlights of the on-

coming vehicle or the leading ve-

hicle are turned off, when the color

of the light is affected due to for-

eign materials on the lights, or

when the light beam is out of

position.

The High Beam Assist system will operate

when the vehicle is driven at speeds of ap-

proximately 19 mph (30 km/h) and above. If

an oncoming vehicle or leading vehicle ap-

pears in front of your vehicle when the

headlight high beam is on, the headlight

will be switched to the low beam automati-

cally.

–

The brightness of the headlights

of the oncoming vehicle or lead-

ing vehicle.

The movement and direction of

the oncoming vehicle and the

leading vehicle.

–

When there is a sudden, continu-

ous change in brightness.

When only one light on the on

coming vehicle or the leading ve-

hicle is illuminated.

Precautions on High Beam Assist

WARNING

When driving on

a

road that

passes over rolling hills, or a road

that has level differences.

When the oncoming vehicle or the

leading vehicle is a two-wheeled

vehicle.

–

When driving on a road with many

curves.

•

The High Beam Assist system is a

convenience but it is not a substitute

for safe driving operation. The driver

should remain alert at all times, en-

sure safe driving practices and

switch the high beams and low beam

manually when necessary.

–

Road conditions (incline, curve,

the road surface, etc.).

When a sign or mirror-like surface

is reflecting intense light towards

the front of the vehicle.

The number of passengers and

the amount of luggage.

–

When the container, etc. being

towed by a leading vehicle is re-

flecting intense light.

•

The high beam or low beam may not

switch automatically under the fol-

lowing conditions. Switch the high

beam and low beam manually.

When a headlight on your vehicle

is damaged or dirty.

Instruments and controls 2-51

When the vehicle speed lowers to less than

approximately 12 mph (20 km/h), the head-

light remains the low beam.

To turn off the High Beam Assist system,

turn the headlight switch to the

posi-

tion or select the low beam position by

placing the lever in the neutral position.

LIC3802

LSD2847

High Beam Assist operations

Ambient image sensor maintenance

The ambient image sensor for the High

Beam Assist system is located above the

To activate the High Beam Assist system,

turn the headlight switch to the AUTO po-

1

inside mirror

. To keep the proper opera-

1

2

sition

and push the lever forward

O

tion of the High Beam Assist system and

prevent a system malfunction, be sure to

observe the following:

(high beam position). The High Beam Assist

indicator light in the meter will illuminate

while the headlights are turned on.

• Always keep the windshield clean.

If the High Beam Assist indicator light does

not illuminate in the above condition, it may

indicate that the system is not functioning

properly. It is recommended that you visit a

NISSAN certified LEAF dealer for this ser-

vice.

• Do not attach a sticker (including trans-

parent material) or install an accessory

near the ambient image sensor.

• Do not strike or damage the areas

around the ambient image sensor.

2-52 Instruments and controls

If the ambient image sensor is damaged

due to an accident, it is recommended that

you visit a NISSAN certified LEAF dealer for

this service.

•

Never leave the light switch on when

the power switch is in the OFF, ACC or

ON position for extended periods of

time even if the headlights turn off

automatically.

WARNING

When the LED DRL system is active, tail

lights on your vehicle are not on. It is

necessary at dusk to turn on your

headlights. Failure to do so could cause

an accident injuring yourself and oth-

ers.

Battery saver system

• When the headlight switch is in the

LED DAYTIME RUNNING LIGHTS

(DRL) SYSTEM (if so equipped)

or

position while the power switch

is in the ON position, the lights will auto-

matically turn off 45 seconds after the

power switch has been placed in the OFF

position.

The LED portion of the headlights auto-

matically illuminates at 100% intensity

when the power switch is in the READY to

drive position with the parking brake re-

leased. The LED DRL system operates with

the headlight switch in the OFF position.

• When the headlight switch remains in the

or

position after the lights

automatically turn off, the lights will turn

on when the power switch is placed in the

ON position.

Turn headlight switch to the

for full illumination when driving at night.

position

If the parking brake is applied before the

power switch is in the READY to drive posi-

tion, the LED DRL system does not operate.

The LED DRL system illuminates once the

parking brake is released. The LED DRL sys-

tem will remain on until the power switch is

pushed to the OFF position.

CAUTION

•

When you turn on the headlight

switch again after the lights auto-

matically turn off, the lights will not

turn off automatically. Be sure to turn

the light switch to the OFF position

when you leave the vehicle for ex-

tended periods of time, otherwise

the battery will be discharged.

Instruments and controls 2-53

Move the lever up or down until the turn

signal begins to flash, but the lever does

not latch, and release the lever. The turn

signal will automatically flash three times.

Choose the appropriate method to signal

a lane change based on road and traffic

conditions.

LIC3801

SIC3671

INSTRUMENT BRIGHTNESS

CONTROL

Press the “+” button to increase the bright-

ness of the instrument panel lights.

TURN SIGNAL SWITCH

Turn signal

1

Move the lever up or down until it

O

latches to signal the turning direction.

When the turn is completed, the turn signal

cancels automatically.

Press the “-” to decrease the brightness of

the instrument panel lights.

Lane change signal

2

Move the lever up or down until the turn

O

signal begins to flash, but the lever does

not latch, to signal a lane change. Hold the

lever until the lane change is completed.

2-54 Instruments and controls

Instruments and controls -> Headlight and turn signal switch for Your Nissan Leaf 4 Door Second Generation (2018-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals