Get Instruments and controls -> HomeLink? Universal Transceiver (if so equipped) Guide for Nissan Leaf 4 Door Second Generation (2018-2025)

HOMELINK® UNIVERSAL

TRANSCEIVER (if so equipped)

The HomeLink® Universal Transceiver pro-

vides a convenient way to consolidate the

functions of up to three individual hand-

held transmitters into one built-in device.

PROGRAMMING HOMELINK®

WARNING

If you have any questions or are having

difficulty programming your HomeLink®

buttons, refer to the HomeLink® web site at:

www.homelink.com or call 1-800-355-3515.

•

Your vehicle's EV system should be

turned off while programming the

HomeLink® Universal Transceiver. For

additional information, refer to

“Push-button power switch” in the

“Starting and driving” section of this

manual.

HomeLink® Universal Transceiver:

• Will operate most radio frequency de-

vices such as garage doors, gates, home

and office lighting, entry door locks and

security systems.

NOTE:

Place the power switch in the ON or ACC

position (without starting the EVsystem)

when programming HomeLink®. It is also

recommended that a new battery be

placed in the hand-held transmitter of

the device being programmed to

HomeLink® for quicker programming

and accurate transmission of the radio

frequency.

Do not use the HomeLink® Universal

Transceiver with any garage door

opener that lacks safety stop and re-

verse features as required by federal

safety standards. (These standards

became effective for opener models

manufactured after April 1, 1982). A

garage door opener which cannot

detect an object in the path of a clos-

ing garage door and then automati-

cally stop and reverse, does not meet

current federal safety standards. Us-

ing a garage door opener without

these features increases the risk of

serious injury or death.

• Is powered by your vehicle's 12–volt bat-

tery. No separate batteries are required. If

the vehicle's 12–volt battery is discharged

or is disconnected, HomeLink® will retain

all programming.

When the HomeLink® Universal Trans-

ceiver is programmed, retain the original

transmitter for future programming pro-

cedures (Example: new vehicle pur-

chases). Upon sale of the vehicle, the

programmed

HomeLink®

Universal

Transceiver buttons should be erased for

security purposes. For additional infor-

mation,

HomeLink®” in this section.

refer

to

“Programming

•

During the programming procedure

your garage door or security gate will

open and close (if the transmitter is

within range). Make sure that people

or objects are clear of the garage

door, gate, etc. that you are

programming.

Instruments and controls 2-71

NOTE:

Some devices may require you to replace

Step 2 with the cycling procedure noted

in “Programming HomeLink® for Cana-

dian customers and gate openers” in this

section.

3. Press and hold the programmed

HomeLink® button and observe the indi-

cator light.

1

• If the indicator light

is solid/

O

continuous, programming is complete

and your device should activate when the

HomeLink® button is pressed and re-

leased.

LIC2365

LIC2366

1

• If the indicator light

blinks rapidly for 2

O

1. Position the end of your hand-held

transmitter 1–3 in (2–8 cm) away from

the HomeLink® surface, keeping the

1

2. Using both hands, simultaneously press

and hold the desired HomeLink® button

and hand-held transmitter button. DO

NOT release until the HomeLink® indica-

1

seconds and then turns to a solid/

continuous light, continue with Steps

4-6 for a rolling code device. A second

person may make the following steps

easier. Use a ladder or other device. Do

not stand on your vehicle to perform the

next steps.

HomeLink® indicator light

in view.

O

tor light

flashes slowly and then rap-

O

idly. When the indicator light flashes rap-

idly, both buttons may be released. (The

rapid flashing indicates successful

programming.)

2-72 Instruments and controls

4. At the receiver located on the garage

door opener motor in the garage, locate

the “learn” or “smart” button (the name

and color of the button may vary by

manufacturer but it is usually located

near where the hanging antenna wire is

attached to the unit). If there is difficulty

locating the button, reference the ga-

rage door opener’s manual.

2. Using both hands, simultaneously press

and hold the desired HomeLink® button

and the hand-held transmitter button.

During training, your hand-held trans-

mitter may automatically stop transmit-

ting. Continue to press and hold the de-

sired HomeLink® button while you press

and re-press (“cycle”) your hand-held

transmitter every 2 seconds until the

frequency signal has been learned. The

HomeLink® indicator light will flash

slowly and then rapidly after several

seconds upon successful training. DO

NOT release until the HomeLink® indica-

tor light flashes slowly and then rapidly.

When the indicator light flashes rapidly,

both buttons may be released. The rapid

flashing indicates successful training.

PROGRAMMING HOMELINK® FOR

CANADIAN CUSTOMERS AND GATE

OPENERS

Canadian radio-frequency laws require

transmitter signals to “time-out” (or quit)

after several seconds of transmission –

which may not be long enough for

HomeLink® to pick up the signal during

training. Similar to this Canadian law, some

U.S. gate operators are designed to “tim-

eout” in the same manner.

5. Press and release the “learn” or “smart”

button.

NOTE:

If you live in Canada or you are having diffi-

culties training a gate operator or garage

door opener by using the “Training” proce-

dures, replace “Programming HomeLink®”

step 2 with the following:

Once the button is pressed, you have

approximately 30 seconds to initiate

the next step.

6. Return to the vehicle and firmly press

and hold the trained HomeLink® button

for 2 seconds and release. Repeat the

“press/hold/release” sequence up to

three times to complete the training

process. HomeLink® should now acti-

vate your rolling code equipped device.

Proceed

with

“Programming

NOTE:

HomeLink®” step 3 to complete.

If the device was unplugged during the

programming procedure, remember to

plug it back in when programming is

completed.

When programming

a

garage door

opener, etc., unplug the device during

the “cycling” process to prevent possible

damage to the garage door opener

components.

7. If you have any questions or are having

difficulty programming your HomeLink®

buttons, refer to the HomeLink® web site

1. For additional information, refer to “Pro-

gramming HomeLink®” step 1 in this

section.

at:

www.homelink.com

or

call

1-800-355-3515.

Instruments and controls 2-73

• position the hand-held transmitter 1 - 3 in

(26 - 76 mm) away from the HomeLink®

surface. Hold the transmitter in that posi-

tion for up to 15 seconds. If HomeLink® is

not programmed within that time, try

holding the transmitter in another posi-

tion – keeping the indicator light in view at

all times.

HomeLink® is now in the programming

mode and can be programmed at any

time beginning with “Programming

HomeLink®” - Step 1.

OPERATING THE HOMELINK®

UNIVERSAL TRANSCEIVER

The HomeLink® Universal Transceiver, after

it is programmed, can be used to activate

the programmed device. To operate, sim-

ply press and release the appropriate pro-

grammed HomeLink® Universal Trans-

ceiver button. The amber indicator light will

illuminate while the signal is being trans-

mitted.

If you have any questions or are having

difficulty programming your HomeLink®

buttons, refer to the HomeLink® web site at:

www.homelink.com or call 1-800-355-3515.

For convenience, the hand-held transmit-

ter of the device may also be used at any

time.

CLEARING THE PROGRAMMED

INFORMATION

PROGRAMMING TROUBLE-

DIAGNOSIS

The following procedure clears the pro-

grammed information from both buttons.

Individual buttons cannot be cleared. How-

ever, individual buttons can be repro-

grammed. For additional information, refer

to “Reprogramming a single HomeLink®

button” in this section.

If the HomeLink® does not quickly learn the

hand-held transmitter information:

• replace the hand-held transmitter bat-

teries with new batteries.

• position the hand-held transmitter with

its battery area facing away from the

HomeLink® surface.

To clear all programming:

1. Press and hold the two outer HomeLink®

buttons until the indicator light begins to

flash in approximately 10 seconds. Do

not hold for longer than 20 seconds.

• press and hold both the HomeLink® and

hand-held transmitter buttons without

interruption.

2. Release both buttons.

2-74 Instruments and controls

For Canada:

REPROGRAMMING A SINGLE

HOMELINK® BUTTON

IF YOUR VEHICLE IS STOLEN

This device complies with Industry

Canada licence-exempt RSS standard(s).

Operation is subject to the following two

conditions: (1) this device may not cause

interference, and (2) this device must ac-

cept any received, including interference

that may cause undesired operation of

the device.

If your vehicle is stolen, you should change

the codes of any non-rolling code device

that has been programmed into

HomeLink®. Consult the Owner's Manual of

each device or call the manufacturer or

dealer of those devices for additional infor-

mation.

To reprogram

a

HomeLink® Universal

Transceiver button, complete the following:

1. Press and hold the desired HomeLink®

button. DO NOT release the button.

2. The indicator light will begin to flash af-

ter 20 seconds. Without releasing the

HomeLink® button, proceed with “Pro-

gramming HomeLink®” - Step 1.

When your vehicle is recovered, you will

need to reprogram the HomeLink® Uni-

versal Transceiver with your new trans-

mitter information.

For questions or comments, contact

HomeLink® at: www.homelink.com or

1–800–355–3515 (except Mexico).

FCC Notice:

For USA:

The HomeLink® Universal Transceiver but-

ton has now been reprogrammed. The

new device can be activated by pressing

the HomeLink® button that was just pro-

grammed. This procedure will not affect

any other programmed HomeLink® but-

tons.

This device complies with Part 15 of the

FCC Rules. Operation is subject to the fol-

lowing two conditions: (1) This device

may not cause harmful interference, and

(2) this device must accept any interfer-

ence received, including interference

that may cause undesired operation.

NOTE:

Changes or modifications not expressly

approved by the party responsible for

compliance could void the user’s author-

ity to operate the equipment.

Instruments and controls 2-75

MEMO

2-76 Instruments and controls

Instruments and controls -> HomeLink? Universal Transceiver (if so equipped) for Your Nissan Leaf 4 Door Second Generation (2018-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals