[ Edit: 2014/ 11/ 7 Model: T32-A ]
switch on the ultrasonic sensor.
It is possible to exclude the ultrasonic (for example,
when leaving pets inside the car or transporting the
vehicle on a ferry).
To exclude the ultrasonic:
1. Close all the windows.
2. Place the ignition switch in the “OFF” position.
3. Push the cancel switch
*
B
located on the ceiling.
The security indicator light will start flashing
rapidly.
4. Close the doors, hood and back door. Lock them
using the remote controller, the Intelligent Key or
the request switch. The security indicator light will
start flashing faster and a buzzer will sound once.
The ultrasonic sensor is now excluded from the theft
warning system. All other functions of the system
remain activated until the theft warning system is
disarmed again.
For models without ultrasonic sensor
GUID-F6883F2C-18CE-4385-9BAC-D9C25E45F1E2
GUID-22018305-9BAB-4201-B6FC-C08EB94AEAE0
1. Close all windows and sunroof (if equipped).
The system can be armed e ven if the
windows are open.
2. Place the ignition switch in the “OFF” position.
3. Remove remote controller or the Intelligent Key
from the vehicle.
4. Close all doors, hood and back door. Lock all
doors. The doors can be locked with remote
controller or the Intelligent Key, door handle
request switch, powe r door lock switch or
mechanical key.
5. Confirm that the security indicator light comes on.
The security indicator light stays on for about 30
seconds. The vehicle security system is now pre-
armed. After about 30 seconds the vehicle
security system automatically shifts into the armed
phase. The security light begins to flash once
every approximately 3 seconds. If, during this 30
seconds pre-arm time period, the door is un-
locked, or the ignition switch is placed in “ON”,
the system will not alarm.
Even when the driver and/or passengers are in
the vehicle, the system will activate with all
doors, hood, and back door locked with the
ignition switch in the “LOCK” position. When
placing the ignition switch in the “ON” position,
the system will be released.
Theft warning system operation:
GUID-22018305-9BAB-4201-B6FC-C08EB94AEAE0
The vehicle security system will give the following
alarm:
. The hazard indicator or headlight blinks and the
horn sounds intermittently.
. The alarm automatically turns off after approxi-
mately 30 or 50 seconds. However, the alarm
reactivates if the vehicle is tampered with again.
The alarm is activated by:
. Unlocking the door or opening the back door
without using the button on the remote controller
or the Intelligent Key, the door handle request
switch or the mechanical key. (Even if the door is
opened by releasing the door inside lock knob, the
alarm will activate.)
. Opening the hood.
How to stop alarm:
GUID-22018305-9BAB-4201-B6FC-C08EB94AEAE0
. The alarm will stop only by unlocking a door by
pushing the “UNLOCK” button on the remote
controller or the Intelligent Key.
. The alarm will not stop if the ignition switch is
placed in the “ON” position.
NISSAN ANTI-THEFT SYSTEM (NATS)
GUID-5E437D07-076E-4181-8CCF-57AFFB80C485
The NISSAN Anti-Theft System (NATS) will not allow
the engine to start without the use of the registered
NATS key.
If the engine does not start using the registered NATS
key, it may be due to interference caused by:
. Another NATS key.
. Automated toll road device.
. Automated payment device.
. Other devices that transmit similar signals.
Start the engine using the following procedure:
1. Re move any items t hat may be causin g the
interference away from the NATS key.
2. Leave the ignition switch in the “ON” position for
approximately 5 seconds.
3. Place the ignition switch in the “OFF” or “LOCK”
position, and wait approximately 10 seconds.
4. Repeat steps 2 and 3 again.
5. Start the engine.
6. Repeat the steps above until all possible inter-
ferences are eliminated.
If this procedure allows the engine to start, NISSAN
recommends placing the registered NATS key sepa-
rate from other devices to avoid interference.
Pre-driving checks and adjustments 3-21
Condition: 'Except for China'/
English 
