2014-2022 Peugeot 108 4 Door In the event of a breakdown -> Temporary puncture repair kit User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

In the event of a breakdown -> Temporary puncture repair kit for Your Peugeot 108 4 Door 2014-2022

In the event of a breakdown  
F Uncoil the pipe stowed under the  
Temporary puncture  
repair kit  
The vehicle's electric system allows the  
connection of the compressor for long  
enough to inflate a tyre after a puncture  
repair.  
compressor.  
Scan the QR code on page 3 to view  
explanatory videos.  
Composition of the kit  
Comprising a compressor and a sealant  
cartridge, it allows the temporary repair of  
a tyre so that you can drive to the nearest  
garage.  
It is designed to repair most punctures which  
could affect the tyre, located on the tyre tread  
or shoulder.  
F Connect the pipe from the compressor to  
the bottle of sealant.  
Avoid removing any foreign bodies which  
have penetrated into the tyre.  
Access to the kit  
1. 12 V compressor, with integral pressure  
gauge.  
2. Sealant cartridge, with integral hose.  
3. Speed limit sticker.  
Repair procedure  
F Park the vehicle without obstructing any  
traffic and apply the parking brake.  
F Follow the safety instructions (hazard  
warning lamps, warning triangle, wearing  
high visibility vest, etc.) according to the  
legislation in force in the country where you  
are driving.  
F Turn the sealant bottle over and secure it in  
This kit is installed in the storage box, under  
the boot floor.  
the notch provided on the compressor.  
F Switch off the ignition.  
104  
In the event of a breakdown  
F Remove the valve cap from the tyre to be  
F Connect the compressor's electric plug to  
F Start the compressor by turning the switch  
to the "l" position until the pressure of the  
tyre reaches 2.0 bars. The sealant product  
is injected under pressure into the tyre;  
do not disconnect the pipe from the valve  
during this operation (risk of blowback).  
repaired, and place it in a clean area.  
the vehicle's 12 V socket.  
F
Affix the speed limit sticker.  
The speed limit sticker must be secured  
to the interior of the vehicle in the driver's  
field of vision, to remind you that a wheel  
is in temporary use.  
If a pressure of 2 bars is not reached after  
about 7 minutes, this indicates that the  
tyre is not repairable; contact a PEUGEOT  
dealer or a qualified workshop for  
assistance.  
F Connect the hose from the bottle of sealant  
to the valve of the tyre to be repaired and  
tighten firmly.  
The tyre inflation pressures are given on  
this label.  
F Place the switch in the "O" position.  
F Disconnect the compressor's electric plug  
from the vehicle's 12 V socket.  
F Replace the cap on the valve.  
F Remove the kit.  
F Check that the compressor switch is at the  
"O" position.  
F Uncoil fully the electric cable, stowed under  
the compressor.  
F Switch on the ignition.  
F Remove and then store the bottle of sealant.  
8
105  
In the event of a breakdown  
F Check that the compressor switch is at the  
"O" position.  
F Uncoil fully the electric cable, stowed under  
the compressor.  
Take care, the sealant product is harmful  
if swallowed and causes irritation to the  
eyes.  
Keep this product out of the reach of  
children.  
Do not exceed the speed of 50 mph  
(80 km/h) when driving with a tyre repaired  
using this type of kit.  
The use-by date of the fluid is marked on  
the bottle.  
After use, do not discard the bottle in  
standard waste, take it to a PEUGEOT  
dealer or an authorised waste disposal  
site.  
Do not forget to obtain a new bottle of  
sealant, available from a PEUGEOT  
dealer or a qualified workshop.  
Checking/adjusting tyre  
pressures  
You can also use the compressor,  
without injecting sealant, to check and, if  
necessary, adjust the tyre pressures  
F Remove the valve cap from the tyre and  
place it in a clean area.  
F Uncoil the pipe stowed under the  
compressor.  
F Connect the compressor's electric plug to  
the vehicle's 12 V socket.  
F Switch on the ignition.  
The tyre inflation pressures are given on  
this label.  
F Drive immediately for approximately three  
miles (five kilometres), at reduced speed  
(between 12 and 37 mph (20 and 60 km/h)),  
to plug the puncture.  
F Stop to check the repair and measure the  
tyre pressure using the kit.  
F Screw the pipe onto the valve and tighten  
firmly.  
106  

Related Topics

In the event of a breakdown
Spare wheel Changing a bulb Changing a fuse 12 V battery Towing the vehicle

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot