Get VISIBILITY Guide for Peugeot 407 4 Door First Generation (2004-2011)

5

Front and rear lamps (ring A)

Front and rear foglamps (ring B)

LIGHTING CONTROL STALK

 Turn ring A to the position re-

quired.

 Turn ring B forwards to switch on

and rearwards to switch off. The

status is conﬁrmed by the lamp on

the instrument panel.

Lighting off,

Front foglamps (turn once)

Automatic illumination of

headlamps,

These operate with the sidelamps and

the dipped or main beam headlamps.

Model without AUTO lighting

Sidelamps,

Rear foglamps (turn twice)

Dipped/mainbeamhead-

lamps.

These operate when the front foglamps

are already on.

Direction indicators

Dipped/main beam change

 Pull the stalk fully towards you.

Left: downwards. The

direction arrow indica-

tor lamp ﬂashes on the

instrument panel.

Model with AUTO lighting

Right: upwards. The

direction arrow indica-

tor lamp ﬂashes on the

instrument panel.

Lighting on

With the ignition off, on opening the

driver's door an audible signal indi-

cates that you have left the lighting on

when leaving the vehicle.

If you forget to return the di-

rection indicator to its normal

position, the volume of the

 Switch the lighting off.

audible signal will increase, if

you are driving at a speed greater than

40 mph (60 km/h) or if the control stalk

is held on for more than 20 seconds.

74

5

Automatic illumination of

headlamps

Activation

Manual "Guide-me-home" lighting

When you leave your vehicle, the side-

lamps and dipped beam headlamps

can be left on for a few seconds.

Whenthefunctionisactivated,the

indicator lamp comes on on the

5-dial instrument panel screen.

The dipped beam headlamps switch

on automatically if the light is poor and

when the windscreen wipers operate

continuously. They switch off when

the light is bright enough or the wind-

screen wipers stop.

Deactivation

Activation:

 switch off the engine,

 "ﬂash" the headlamps,

 get out of the vehicle and lock it.

Warning: in foggy weather or in snow,

the sunshine sensor can detect sufﬁ-

cient light. The lighting will not come

on automatically. If necessary, you

must switch the dipped beam head-

lamps on manually.

When the function is deactivated,

theindicatorlampcomesononthe

5-dial instrument panel screen.

If the sunshine/brightness sensor

does not function correctly, the

sidelamps and dipped beam headlam-

ps come on.

Automatic "Guide-me-home"

lighting

When you leave your vehicle with

the automatic illumination of head-

lamps activated, the sidelamps and

dipped beam headlamps remain on

for the duration selected after the igni-

tion is switched off.

To deactivate or activate the

function, use the "Persona-

lisation - conﬁguration"

menu on your multifunction

screen.

Consult a PEUGEOT dealer.

To deactivate or activate the

"Automatic guide-me-home

lighting" function, use the

"Personalisation - confi-

guration" menu on your

multifunction screen.

For safety reasons, activation/

deactivation of the "Automatic

illumination of headlampss"

function via the menu must be

carried out when stationary.

Do not cover the sunshine/

brightness sensor, located in

the centre of the windscreen.

It is used to regulate the air

conditioning and for the automatic il-

lumination of headlamps.

The duration of the lighting

can be set via the "Person-

alisation

- conﬁguration"

menu of your multifunction

screen.

75

5

Automatic illumination of

headlamps

Activation

Manual "Guide-me-home" lighting

When you leave your vehicle, the side-

lamps and dipped beam headlamps

can be left on for a few seconds.

Whenthefunctionisactivated,the

indicator lamp comes on on the

5-dial instrument panel screen.

The dipped beam headlamps switch

on automatically if the light is poor and

when the windscreen wipers operate

continuously. They switch off when

the light is bright enough or the wind-

screen wipers stop.

Deactivation

Activation:

 switch off the engine,

 "ﬂash" the headlamps,

 get out of the vehicle and lock it.

Warning: in foggy weather or in snow,

the sunshine sensor can detect sufﬁ-

cient light. The lighting will not come

on automatically. If necessary, you

must switch the dipped beam head-

lamps on manually.

When the function is deactivated,

theindicatorlampcomesononthe

5-dial instrument panel screen.

If the sunshine/brightness sensor

does not function correctly, the

sidelamps and dipped beam headlam-

ps come on.

Automatic "Guide-me-home"

lighting

When you leave your vehicle with

the automatic illumination of head-

lamps activated, the sidelamps and

dipped beam headlamps remain on

for the duration selected after the igni-

tion is switched off.

To deactivate or activate the

function, use the "Persona-

lisation - conﬁguration"

menu on your multifunction

screen.

Consult a PEUGEOT dealer.

To deactivate or activate the

"Automatic guide-me-home

lighting" function, use the

"Personalisation - confi-

guration" menu on your

multifunction screen.

For safety reasons, activation/

deactivation of the "Automatic

illumination of headlampss"

function via the menu must be

carried out when stationary.

Do not cover the sunshine/

brightness sensor, located in

the centre of the windscreen.

It is used to regulate the air

conditioning and for the automatic il-

lumination of headlamps.

The duration of the lighting

can be set via the "Person-

alisation

- conﬁguration"

menu of your multifunction

screen.

75

5

Daytime running lamps*

MANUAL HEADLAMP

ADJUSTMENT

AUTOMATIC HEADLAMP

ADJUSTMENT

On vehicles which are equipped with day-

time running lamps, the dipped beam head-

lamps come on when the vehicle is started.

This indicator lamp comes on on

the instrument panel screen.

The instruments and controls

(multifunction screen, air con-

ditioning control panel...) are

only lit on switching to the

automatic illumination of headlamps

mode or when the lighting is switched

on manually.

For vehicles ﬁtted with halogen bulbs,

depending on the load in your vehicle,

adjusting the beam of your headlamps

is recommended.

0. 1 or 2 people in the front seats.

-. 3 people.

When stationary with the ignition

on, the system automatically corrects

the height of the beam, whatever the

load of the vehicle. The driver is then

assured of having optimum lighting

and not causing a nuisance to other

road users.

1. 5 people.

-. Intermediate adjustment

2. 5 people + maximum authorised

loads.

-. Intermediate adjustment

3. Driver + maximum authorised loads.

Initial setting is position 0.

In cases of malfunction, the

warning lamp comes on on the

instrument panel screen, ac-

companied by an audible sig-

nal and a message on the multifunction

screen. The system places your head-

lamps to the low position.

Do not touch the xenon bulbs. Consult

a PEUGEOT dealer.

* According to country.

76

5

WINDSCREEN WIPER

CONTROL STALK

Windscreen wiper with intermittent

wipe

Windscreen wiper with automatic

wipe

Windscreen wiper with Intermittent

and automatic wipe

2

1

l

Fast wipe (heavy rain).

Normal wipe (moderate rain).

Intermittent wipe.

Off.

2

1

Fast wipe (heavy rain).

Normal wipe (moderate rain).

2

1

I

Fast wipe (heavy rain).

Normal wipe (moderate rain).

Intermittent wipe.

Off.

AUTO Automatic wipe.

Off.

 Single wipe (press downwards).

0

 Single wipe (press downwards).

In the Intermittent position, the wiping

speed is in proportion to the vehicle

speed.

In the AUTO position, no action on

your part is necessary.

Automatic, then single wipe

(see following page).

In the AUTO position, no action on

your part is necessary.

In the Intermittent position, the wiping

speed is in proportion to the vehicle

speed.

The windscreen wiping

must be reactivated if the

ignition has been switched off

for more than one minute.

The windscreen wiping

must be reactivated if the

ignition has been switched off

for more than one minute.

77

5

Automatic rain sensitive

windscreen wipers

In the event of malfunction, the

windscreen wipers will operate in in-

termittent mode.

Contact a PEUGEOT dealer to have

the system checked.

REAR WIPER CONTROL

(407 SW)

Activation

Move the control to position 0 then re-

turn it to the AUTO position.

An indicator lamp comes on on the in-

strument panel screen, accompanied

by a message on the multifunction

screen.

In the AUTO position, the windscreen

wipers operate automatically and

adapt their speed to the intensity of

the rainfall.

Turn the ring to the ﬁrst notch for inter-

mittent wiping.

The control must be reactivated if

the ignition has been switched off.

To do this, move the control to any

position then return it to the required

position.

Control with Intermittent and

automatic wiping

Manual operation of the wiper stalk by

moving the stalk A up and returning

it to position "0" interrupts the AUTO

position, the deactivation indicator

lamp comes on on the instrument pan-

el screen, accompanied by a message

on the multifunction screen.

Deactivation

Automatic rear wiper

If the windscreen wipers control is ac-

tivated and you engage reverse gear,

the rear wiper operates in intermittent

mode.

Do not cover the rain sensor

located on the windscreen be-

hind the rear view mirror.

When using an automatic car

Control with automatic wiping only

wash to wash your vehicle, switch off

the ignition or check that the wiper

stalk is not in the automatic position.

In winter, it is advisable to wait for the

windscreen to completely clear of ice

before operating the automatic wipers.

Note: if a bicycle carrier is

used, deactivate this function

by going to the "personalisa-

tion - conﬁguration" menu on

the multifunction screen or install a

special bicycle carrier approved by

PEUGEOT.

Manual operation of the wiper stalk in-

terrupts the AUTO position, the deacti-

vation indicator lamp comes on on the

instrument panel screen, accompa-

nied by a message on the multifunc-

tion screen.

78

5

Automatic rain sensitive

windscreen wipers

In the event of malfunction, the

windscreen wipers will operate in in-

termittent mode.

Contact a PEUGEOT dealer to have

the system checked.

REAR WIPER CONTROL

(407 SW)

Activation

Move the control to position 0 then re-

turn it to the AUTO position.

An indicator lamp comes on on the in-

strument panel screen, accompanied

by a message on the multifunction

screen.

In the AUTO position, the windscreen

wipers operate automatically and

adapt their speed to the intensity of

the rainfall.

Turn the ring to the ﬁrst notch for inter-

mittent wiping.

The control must be reactivated if

the ignition has been switched off.

To do this, move the control to any

position then return it to the required

position.

Control with Intermittent and

automatic wiping

Manual operation of the wiper stalk by

moving the stalk A up and returning

it to position "0" interrupts the AUTO

position, the deactivation indicator

lamp comes on on the instrument pan-

el screen, accompanied by a message

on the multifunction screen.

Deactivation

Automatic rear wiper

If the windscreen wipers control is ac-

tivated and you engage reverse gear,

the rear wiper operates in intermittent

mode.

Do not cover the rain sensor

located on the windscreen be-

hind the rear view mirror.

When using an automatic car

Control with automatic wiping only

wash to wash your vehicle, switch off

the ignition or check that the wiper

stalk is not in the automatic position.

In winter, it is advisable to wait for the

windscreen to completely clear of ice

before operating the automatic wipers.

Note: if a bicycle carrier is

used, deactivate this function

by going to the "personalisa-

tion - conﬁguration" menu on

the multifunction screen or install a

special bicycle carrier approved by

PEUGEOT.

Manual operation of the wiper stalk in-

terrupts the AUTO position, the deacti-

vation indicator lamp comes on on the

instrument panel screen, accompa-

nied by a message on the multifunc-

tion screen.

78

5

Rear wash-wipe

Windscreen and headlamp wash

FRONT COURTESY LAMP

Pull the windscreen wiper stalk towards

you. The windscreen wash then the

windscreen wipers operate for a ﬁxed

period.

The headlamp wash is also activated,

if the headlamps are on.

Screenwash/

headlamp wash low

Turn the ring beyond the ﬁrst notch,

the wash-wipe then the wiper operate

for a set period of time.

When the minimum level of

the reservoir is reached, this

warning light comes on, ac-

companied by an audible

signal and a message on the

multi-function display.

1. Courtesy lamp

2. Map reading lamps

Note: the rear wiper and rear

wash-wipe functions are de-

activated automatically when

the rear screen is opened.

With the key in the ignition on or starting

position, operate the relevant switch.

The front courtesy lamp comes on

when the ignition key is removed, on

unlocking the vehicle or on opening

one of the doors.

It gradually goes off after the ignition

has been switched on or when the ve-

hicle is locked.

Next time you stop, ﬁll the screenwash/

headlamp wash reservoir.

The warning light comes on each time

the stalk is operated, until the reservoir

is ﬁlled.

 Pressing switch 1 turns on the front

courtesy lamp.

The courtesy lamp can be deactivated

by pressing switch 1 with the door open.

The map reading lamps are not affected

by this and may be switched on.

 To re-activate the lamps, press the

switch, with the door open.

79

5

Rear wash-wipe

Windscreen and headlamp wash

FRONT COURTESY LAMP

Pull the windscreen wiper stalk towards

you. The windscreen wash then the

windscreen wipers operate for a ﬁxed

period.

The headlamp wash is also activated,

if the headlamps are on.

Screenwash/

headlamp wash low

Turn the ring beyond the ﬁrst notch,

the wash-wipe then the wiper operate

for a set period of time.

When the minimum level of

the reservoir is reached, this

warning light comes on, ac-

companied by an audible

signal and a message on the

multi-function display.

1. Courtesy lamp

2. Map reading lamps

Note: the rear wiper and rear

wash-wipe functions are de-

activated automatically when

the rear screen is opened.

With the key in the ignition on or starting

position, operate the relevant switch.

The front courtesy lamp comes on

when the ignition key is removed, on

unlocking the vehicle or on opening

one of the doors.

It gradually goes off after the ignition

has been switched on or when the ve-

hicle is locked.

Next time you stop, ﬁll the screenwash/

headlamp wash reservoir.

The warning light comes on each time

the stalk is operated, until the reservoir

is ﬁlled.

 Pressing switch 1 turns on the front

courtesy lamp.

The courtesy lamp can be deactivated

by pressing switch 1 with the door open.

The map reading lamps are not affected

by this and may be switched on.

 To re-activate the lamps, press the

switch, with the door open.

79

5

REAR COURTESY LAMP

(SALOON)

REAR READING LAMPS

(407 SW)

Sill illumination

The sill lighting is at the bottom of each

door panel.

The lamps come on automatically

when a door is opened and switch off

automatically when all of the doors are

closed.

Boot light

The boot light is located in the right-

hand boot trim.

It comes on automatically when the

boot is opened and switches off auto-

matically when the boot is closed.

With the key in the ignition on or start-

ing position, press the corresponding

switch.

The rear reading lamps come on when

the key is removed from the ignition

and when the vehicle is unlocked.

They switch off gradually when the ig-

nition is switched on or when the ve-

hicle is locked.

1. Courtesy lamp

2. Map reading lamps

With the key in the ignition on or start-

ing position, operate the relevant

switch.

The rear courtesy lamp comes on

when the ignition key is removed, on

unlocking the vehicle or on opening

one of the doors.

It gradually goes off after the ignition

has been switched on or the vehicle

is locked.

 Pressing switch 1 switches on the

rear reading lamp concerned for

ten minutes.

 Pressing switch 1 turns on the rear

courtesy lamp.

The courtesy lamp can be deactivated

by pressing switch 1 with the door open.

The map reading lamps are not affected

by this and may be switched on.

 To re-activate the lamps, press the

switch, with the door open.

80

VISIBILITY for Your Peugeot 407 4 Door First Generation (2004-2011)

Related Topics