2019-2024 Porsche Taycan 2 Door Starting, driving and stopping the vehicle User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Starting, driving and stopping the vehicle for Your Porsche Taycan 2 Door First Generation (2019-2024)

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Starting, driving and stopping the vehicle
236
Starting, driving and stop-
ping the vehicle
General Safety Instructions
WARNING
Reduced driving noise
with electric vehicles
Even when E-Sound is switched on in accordance
with legal requirements, an electric vehicle produces
very little driving noise, which means that other road
users might not even hear it. There is therefore a risk
of accidents, particularly in areas with traffic calm-
ing, while manoeuvring or parking.
e Be particularly attentive while driving!
Operating principle
A distinction is made between readiness for opera-
tion (standby) and readiness to drive. Both are acti-
vated separately.
Readiness for operation
When you get into the vehicle, the key you have with
you is detected by the vehicle and readiness for op-
eration is established automatically. Some electrical
equipment and electronic systems, such as the cen-
tral display, are available.
e To save the battery, only leave the vehicle in
standby (ready for operation) and only use the
active electrical equipment for as long as is ab-
solutely necessary.
Readiness to drive
The vehicle is ready to drive when drive position D, N
or R is engaged. The vehicle is now ready to drive
and can be moved.
Drive positions
Fig. 194: Drive position display
The following drive positions are available:
D — Drive
Drive position D for driving forwards.
R — Reverse gear
Drive position R for driving in reverse.
Only engage while the vehicle is stationary and the
brake is applied.
N — Neutral
Drive position N must be engaged while the vehicle
is being transported or in car washes, for example.
P — Park
Drive position P for securing the vehicle.
Drive positions D, R and N are selected using the
selector lever to the right of the steering wheel,
while drive position P is selected by pressing the P
button.
Starting and driving the vehicle
Establishing readiness for operation
bb High-voltage battery is sufficiently charged.
bb Disconnect the vehicle plug from the vehicle
charge port.
bb Driver's key in passenger compartment.
Automatically
e Get in and shut the driver's door. Driver's key is
detected in the passenger compartment.
Ready for operation.
Manually
Fig. 195: Power button
bb Readiness for operation switched off.
e Press the Power button. Driver's key is detected
in the passenger compartment.
Ready for operation.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Starting, driving and stopping the vehicle
237
Establishing readiness for operation and driv-
ing off
bb Ready for operation.
bb Vehicle plug removed from the charge port,
charge port door closed and charging cable
safely stowed.
1. Press the brake pedal.
2. Select transmission range D or R with the selec-
tor lever.
The parking lock and the electric parking brake
are deactivated automatically.
3. To drive off, release the brake pedal and slowly
press the accelerator pedal.
The range depends on, among other things, the
driving style, the climatic conditions, the use of en-
ergy-intensive loads and the selected vehicle set-
tings, e.g. driving mode.
Information
The readiness for operation is switched off in the
following situations:
– with corresponding settings in the energy man-
agement system
– if the vehicle was locked from outside
– by opening the driver's door and the driver's seat
belt in drive positions D or R
– by pressing the P button
– by other systems that, for example, automatically
activate drive position P or request the activation
of P if there is an error
Driving off at high acceleration (Launch
Control)
WARNING
Driving off at high
acceleration
When driving off at high acceleration, you may lose
control of the vehicle or endanger other road users
under certain circumstances (poor road conditions,
lack of attention, etc.).
e Only drive off at high acceleration on public roads
if the road and traffic conditions permit.
e Do not endanger other road users when driving
off at high acceleration.
The vehicle already permits you to drive off at an
extremely high rate of acceleration in normal driving
mode. Maximum acceleration from a standstill is
achieved using Launch Control, however.
Driving off with Launch Control
bb Vehicle is at a standstill.
bb Readiness for operation established.
bb Steering wheel is not turned.
bb Drive position D selected.
bb Driving mode SPORT or SPORT PLUS activated.
1. Press the brake pedal with your left foot.
2. Quickly press down the accelerator fully and hold
it down.
A message appears on the instrument cluster.
3. Release the brake pedal within a short space of
time.
Vehicle accelerates to the maximum.
Information
Stress on components increases dramatically when
starting with maximum acceleration in comparison
with normal driving off.
Energy recovery (recuperation)
WARNING
Unsuitable use of
recuperation
Recuperation is a system that is used only for energy
recovery. It is not a driver assistance system and
cannot take over any driver assistance system tasks.
e Do not use the deceleration effect of recupera-
tion as a distance control system.
e Always be ready to brake and stay a safe dis-
tance away from the vehicle in front.
e For greater braking power or for braking the ve-
hicle to a standstill, press the brake pedal as
required.
WARNING
Automatic overrun recu-
peration limited or not
available
The maximum overrun recuperation is limited.
The detection capability of the sensors can be im-
paired by soiling, bad weather conditions (rain, snow,
ice, fog, spray) and unfavourable road conditions
(stone chippings, reflective objects). Vehicles up
ahead may not be adequately detected, or may not
be detected at all.
If automatic overrun recuperation (Auto setting) is
not available, e.g. if sensors are dirty, a message to
this effect will appear in the instrument cluster.
e Do not use automatic overrun recuperation in
conditions of poor visibility and bad road
conditions.
Operating principle
During recuperation, the drive converts most of the
kinetic energy into electrical energy, which is stored
in the high-voltage battery. A distinction is made
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Starting, driving and stopping the vehicle
238
between overrun recuperation and braking
recuperation:
– Overrun recuperation starts as soon as you take
your foot off the accelerator pedal and slows
down the vehicle. You can configure the overrun
recuperation strength.
– When you press the brake, braking recuperation
increases the amount of recuperated energy to a
maximum. A higher braking request is then
achieved using the vehicle's wheel brakes.
Overrun recuperation settings
The following overrun recuperation settings can be
selected:
Set-
ting
Dis-
play
Meaning
Off No dis-
play
No overrun recuperation.
Vehicle coasting.
On
Overrun recuperation with
moderate deceleration of
the vehicle.
Auto
Variable adaptation of over-
run recuperation based on
data relating to the area
around the vehicle.
Information
The deceleration effect of overrun recuperation can
be limited if the charge state of the high-voltage
battery is high, for example.
e Compensate for reduced overrun recuperation by
pressing the brake if necessary.
The overrun recuperation strength is displayed in
the power meter.
Selecting overrun recuperation level
e Press the recuperation button on the steering
wheel:
– Quick press = Switch overrun recuperation on
and off
– Press and hold = Switch automatic overrun
recuperation (Auto) on and off
– or –
e Drive e Recuperation (accelerator pedal)
The selected setting is shown on the instrument
cluster.
Information
Automatic overrun recuperation is only available
when PSM is active. Automatic overrun recuperation
is not available in "PSM SPORT" mode.
Information
The various overrun recuperation settings are as-
signed to the driving modes, but can also be freely
selected by the driver.
Personalisation is possible in the INDIVIDUAL driving
mode.
Driving in coasting mode
"Coasting" is the term used to describe driving
without the braking effect of overrun recuperation.
This function is designed to increase efficiency by
reducing power consumption and increasing the
range. Coasting occurs after the accelerator pedal is
fully released slowly. Coasting ends when the accel-
erator pedal is pressed.
bb Driving in transmission range D.
bb PSM is active.
bb No severe uphill or downhill gradients.
bb Recuperation is switched off.
e Slowly remove your foot from the accelerator
pedal.
Information
Coasting mode is also possible in "SPORT" and
"SPORT PLUS" driving modes. The overrun recuper-
ation setting that is activated as standard for these
driving modes must be switched off when selecting
these modes.
Stop, park and exit the vehicle
WARNING
Inactive power steering
and brake booster
The power steering and brake booster are only ef-
fective when the vehicle is ready for operation. If the
vehicle is not ready for operation, much greater force
is required to turn the steering wheel or brake.
e Only turn the vehicle off when it is stationary.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Starting, driving and stopping the vehicle
239
WARNING
Danger of the vehicle
rolling away
In the following situations, the parking brake is not
active and the vehicle may roll away.
– Leaving the vehicle with the N drive position
engaged.
– If the driver door is opened and the driver's seat
belt is unfastened, the parking brake is deacti-
vated when the brake pedal is applied and the D
or R drive position is selected again.
This can result in injury and damage to the vehicle. A
warning about the danger of the vehicle rolling away
is displayed on the instrument cluster.
e Before leaving the vehicle, activate the parking
brake by pressing the P button.
Stopping the vehicle
e For a brief stop (e.g. at traffic lights), leave the
selector lever in the D drive position and hold the
vehicle with the brake pedal.
e The HOLD function actively holds the vehicle
automatically at a standstill after braking to a
stop on an incline.
Parking the vehicle
Selecting the P drive position secures the vehicle
against rolling away.
Activating the P drive position manually
Fig. 196: Parking lock and electric parking brake button
bb Hold the vehicle still by pressing the brake pedal.
e Press the P button.
The parking lock and the electric parking brake
are activated simultaneously.
The brake warning light
and the P drive po-
sition display light up on the instrument cluster
Activating the P drive position automatically
bb Hold the vehicle in place by pressing the brake
pedal.
bb D or R drive position selected.
e Open the driver’s door and driver side seat belt.
The parking lock and the electric parking brake
are activated automatically.
The brake warning light
and the P drive po-
sition display light up on the instrument cluster
– or –
e Turn off the vehicle using the power button.
The parking lock is activated automatically.
The P drive position display lights up on the in-
strument cluster.
The parking brake is also activated when parking
the vehicle on inclines and gradients of over 8%.
The brake warning light
lights up.
WARNING
Electric parking brake is
deactivated
If the vehicle is turned off using the power button on
an incline or gradient, the electric parking brake may
not be activated (e.g. in the case of a slight incline or
gradient). The vehicle can roll away.
e Always press the P button to activate the parking
brake on inclines and gradients before turning off
the vehicle.
Activating and deactivating the electric parking
brake manually.
The electric parking brake can be activated or deac-
tivated on the central display independently of the P
drive position.
e
e Setting e Vehicle e Electric parking
brake
The brake warning light
lights up or goes out.
Responding to warning messages
The brake warning light
flashes if the electric
parking brake has not been applied fully in a sta-
tionary vehicle.
If it was not possible to activate the parking lock, a
warning appears in the instrument cluster.
Always heed any warning and information messages
displayed in the vehicle.
> Please refer to chapter "Warn- und Information-
smeldungen" on page 271.
Turn off the vehicle and get out.
bb Parking lock and parking brake activated.
e Exit and lock the vehicle.
The vehicle is turned off.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Starting, driving and stopping the vehicle
240
Information
If you do not exit the vehicle, the vehicle may also be
turned off by pressing and holding the power button
(approx. 1 second).
Information
The vehicle is turned off automatically in the follow-
ing situations:
– after 30 minutes
– Battery charge level below minimum limit
Additional information
Leaving the vehicle in drive position N
In drive position N, driving readiness is switched off
after 30 seconds in the following situations:
– Parking brake is not activated
– Driver’s door is opened and driver’s seat belt is
not fastened
– Brake pedal is not pressed

Related Topics

Popular Owner Manuals