2019-2024 Porsche Taycan 2 Door Starting, driving and stopping the vehicle -> Starting and driving the vehicle User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Starting, driving and stopping the vehicle -> Starting and driving the vehicle for Your Porsche Taycan 2 Door First Generation (2019-2024)

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Starting, driving and stopping the vehicle
236
Starting, driving and stop-
ping the vehicle
General Safety Instructions
WARNING
Reduced driving noise
with electric vehicles
Even when E-Sound is switched on in accordance
with legal requirements, an electric vehicle produces
very little driving noise, which means that other road
users might not even hear it. There is therefore a risk
of accidents, particularly in areas with traffic calm-
ing, while manoeuvring or parking.
e Be particularly attentive while driving!
Operating principle
A distinction is made between readiness for opera-
tion (standby) and readiness to drive. Both are acti-
vated separately.
Readiness for operation
When you get into the vehicle, the key you have with
you is detected by the vehicle and readiness for op-
eration is established automatically. Some electrical
equipment and electronic systems, such as the cen-
tral display, are available.
e To save the battery, only leave the vehicle in
standby (ready for operation) and only use the
active electrical equipment for as long as is ab-
solutely necessary.
Readiness to drive
The vehicle is ready to drive when drive position D, N
or R is engaged. The vehicle is now ready to drive
and can be moved.
Drive positions
Fig. 194: Drive position display
The following drive positions are available:
D — Drive
Drive position D for driving forwards.
R — Reverse gear
Drive position R for driving in reverse.
Only engage while the vehicle is stationary and the
brake is applied.
N — Neutral
Drive position N must be engaged while the vehicle
is being transported or in car washes, for example.
P — Park
Drive position P for securing the vehicle.
Drive positions D, R and N are selected using the
selector lever to the right of the steering wheel,
while drive position P is selected by pressing the P
button.
Starting and driving the vehicle
Establishing readiness for operation
bb High-voltage battery is sufficiently charged.
bb Disconnect the vehicle plug from the vehicle
charge port.
bb Driver's key in passenger compartment.
Automatically
e Get in and shut the driver's door. Driver's key is
detected in the passenger compartment.
Ready for operation.
Manually
Fig. 195: Power button
bb Readiness for operation switched off.
e Press the Power button. Driver's key is detected
in the passenger compartment.
Ready for operation.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Starting, driving and stopping the vehicle
237
Establishing readiness for operation and driv-
ing off
bb Ready for operation.
bb Vehicle plug removed from the charge port,
charge port door closed and charging cable
safely stowed.
1. Press the brake pedal.
2. Select transmission range D or R with the selec-
tor lever.
The parking lock and the electric parking brake
are deactivated automatically.
3. To drive off, release the brake pedal and slowly
press the accelerator pedal.
The range depends on, among other things, the
driving style, the climatic conditions, the use of en-
ergy-intensive loads and the selected vehicle set-
tings, e.g. driving mode.
Information
The readiness for operation is switched off in the
following situations:
– with corresponding settings in the energy man-
agement system
– if the vehicle was locked from outside
– by opening the driver's door and the driver's seat
belt in drive positions D or R
– by pressing the P button
– by other systems that, for example, automatically
activate drive position P or request the activation
of P if there is an error
Driving off at high acceleration (Launch
Control)
WARNING
Driving off at high
acceleration
When driving off at high acceleration, you may lose
control of the vehicle or endanger other road users
under certain circumstances (poor road conditions,
lack of attention, etc.).
e Only drive off at high acceleration on public roads
if the road and traffic conditions permit.
e Do not endanger other road users when driving
off at high acceleration.
The vehicle already permits you to drive off at an
extremely high rate of acceleration in normal driving
mode. Maximum acceleration from a standstill is
achieved using Launch Control, however.
Driving off with Launch Control
bb Vehicle is at a standstill.
bb Readiness for operation established.
bb Steering wheel is not turned.
bb Drive position D selected.
bb Driving mode SPORT or SPORT PLUS activated.
1. Press the brake pedal with your left foot.
2. Quickly press down the accelerator fully and hold
it down.
A message appears on the instrument cluster.
3. Release the brake pedal within a short space of
time.
Vehicle accelerates to the maximum.
Information
Stress on components increases dramatically when
starting with maximum acceleration in comparison
with normal driving off.
Energy recovery (recuperation)
WARNING
Unsuitable use of
recuperation
Recuperation is a system that is used only for energy
recovery. It is not a driver assistance system and
cannot take over any driver assistance system tasks.
e Do not use the deceleration effect of recupera-
tion as a distance control system.
e Always be ready to brake and stay a safe dis-
tance away from the vehicle in front.
e For greater braking power or for braking the ve-
hicle to a standstill, press the brake pedal as
required.
WARNING
Automatic overrun recu-
peration limited or not
available
The maximum overrun recuperation is limited.
The detection capability of the sensors can be im-
paired by soiling, bad weather conditions (rain, snow,
ice, fog, spray) and unfavourable road conditions
(stone chippings, reflective objects). Vehicles up
ahead may not be adequately detected, or may not
be detected at all.
If automatic overrun recuperation (Auto setting) is
not available, e.g. if sensors are dirty, a message to
this effect will appear in the instrument cluster.
e Do not use automatic overrun recuperation in
conditions of poor visibility and bad road
conditions.
Operating principle
During recuperation, the drive converts most of the
kinetic energy into electrical energy, which is stored
in the high-voltage battery. A distinction is made

Related Topics

Popular Owner Manuals