2019-2024 Porsche Taycan 2 Door Tyres and Wheels User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Tyres and Wheels for Your Porsche Taycan 2 Door First Generation (2019-2024)

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
249
Tyres and Wheels
In addition to correct tyre inflation pressure and
correct wheel alignment, the service life of the tyres
also depends on your driving style. Abrupt accelera-
tion, high cornering speeds and heavy braking in-
crease tyre wear. Tyre wear is also greater at higher
outside temperatures and on rough road surfaces.
Complying with load and speed
requirements
e Drive at an appropriate speed.
e Do not overload the vehicle, and check the roof
load.
> Please refer to chapter "Technical Data" on
page 308.
Checking tyre pressure
NOTICE
Insufficient tyre pressure can cause tyres to over-
heat and thus be damaged – even invisibly.
e Hidden tyre damage will not be eliminated by
correcting the tyre pressure.
e Never let air out of warm tyres. When tyres are
warm, the tyre inflation pressure is increased.
This could cause the tyre pressure to fall below
the prescribed value.
Fig. 210: Tyre-pressure plate fixing point
The tyre inflation pressure must match the pre-
scribed value. These values are for cold tyres (20 °
C).
e Observe tyre-pressure plate.
e Check the tyre pressure at least every 2 weeks
when the tyres are cold.
Tyre Pressure Monitoring (TPM)
Tyre Pressure Monitoring offers the following
functions:
– Permanent monitoring of tyre pressure and
temperature.
– Display of actual tyre pressure (actual pressure)
while driving.
– Tyre pressure warnings in two stages (yellow and
red warning).
– Vehicle is stationary: Display of the pressure de-
viation from the required pressure.
The tyre pressure warning light
and a corre-
sponding message on the instrument cluster warn
against loss of pressure in two stages (yellow and
red tyre pressure warning, depending on the extent
of the pressure loss).
The tyre pressure warning light goes out only when
the tyre pressure has been corrected.
The yellow tyre pressure warning is displayed for
around 10 seconds after the car comes to a stand-
still and is switched off or when the vehicle is turned
on again. The yellow tyre pressure warning can be
acknowledged when the vehicle is turned on. The red
tyre pressure warning also appears during driving
and can be acknowledged.
e If the tyre pressure warning light lights up and a
tyre pressure warning is displayed despite the
correct tyre pressure: Visit a qualified specialist
workshop. Porsche recommends a Porsche part-
ner as they have trained workshop personnel and
the necessary parts and tools.
Information
Tyre Pressure Monitoring gives a warning about a
pressure drop caused by natural diffusion as well as
about a gradual loss of pressure caused by foreign
objects. Tyre Pressure Monitoring cannot warn you
about tyre damage that occurs suddenly (e.g. a flat
tyre due to unexpected external effects).
WARNING
Defective tyres
Driving with defective tyres can result in serious
accidents.
e When a red tyre pressure warning appears on the
instrument cluster: stop immediately in a suit-
able place and check the tyres for damage. If
necessary, correct the damage using tyre sealant
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
250
or fit the spare wheel.
e Do not continue driving with defective tyres.
Have defective tyres replaced immediately. Visit
a qualified specialist workshop. Porsche recom-
mends a Porsche partner as they have trained
workshop personnel and the necessary parts and
tools.
e Do not drive with tyres in which the tyre pressure
drops again very quickly. In case of doubt, have
tyres checked by a qualified specialist workshop.
Porsche recommends a Porsche partner as they
have trained workshop personnel and the neces-
sary parts and tools.
Faults in the Tyre Pressure Monitoring (TPM)
system
TPM will not function correctly in the following sit-
uations, for example:
– If the Tyre Pressure Monitoring is faulty
– If wheel transmitters for Tyre Pressure Monitor-
ing are missing
– During the learning phase after the tyre settings
have been updated
– After a wheel change without updating the tyre
settings
– If tyre temperatures are too high
Checking the tyre pressure in the instrument
cluster
The individual tyre pressures are only displayed
above a speed of approx. 25 km/h (16 mph) or if the
tyre has been inflated by at least 0.1 bar (1.5 psi).
When the vehicle is turned on after the vehicle has
been stationary for more than approx. 10 minutes,
lines (-.-) will appear instead of the tyre pressures.
e Tyre info e Current press.
> Please refer to chapter "Operating the instru-
ment cluster" on page 129.
The display of the actual pressure is only for infor-
mation. The tyre pressures change depending on the
temperature.
e Under no circumstances should the tyre pres-
sures be changed based on this display.
Checking the pressure deviation in the in-
strument cluster
Fig. 211: Example of pressure difference
bb Vehicle is stationary.
e Tyre info e Pressure deviation
> Please refer to chapter "Operating the instru-
ment cluster" on page 129.
The difference to the required pressure is displayed
on the relevant wheel. Example:
If –0.1 bar (–1.5 psi) is displayed for the rear right
wheel, 0.1 bar (1.5 psi) must be added to this tyre.
The displayed pressures take into account the tyre
temperature.
e Always use the pressure deviation from the dis-
play or from the corresponding tyre pressure
warning to correct the tyre pressure.
Setting tyres
Settings for tyre type, tyre size and load can be ad-
justed via the central display:
> Please refer to chapter "Configuring Tyre Pres-
sure Monitoring (TPM) on the central display" on
page 250.
Configuring Tyre Pressure Moni-
toring (TPM) on the central
display
WARNING
Incorrect settings
Low or high tyre pressure irreparably damages the
tyre and the wheel, lengthens the braking distance
and greatly increases the risk of an accident.
Despite the Tyre Pressure Monitoring system, it is
still the driver’s responsibility to ensure that the
tyres are inflated with the correct tyre pressure and
the vehicle settings are correct. Incomplete or in-
correct settings may affect the accuracy of warnings
and messages.
e Adapt tyre pressure to suit your specific tyres
and the payload.
e Make sure that the settings in the TPM menu
correspond to the tyres fitted on the vehicle and
its payload (especially after a wheel change or
changes in vehicle loading).
e Then select the type and size of fitted tyre again
in the TPM menu, even if the settings for the
newly fitted set of wheels are the same as for the
old wheels.
Accessing filling information
bb Vehicle is stationary.
e
e Setting e Vehicle eTyre pressure
monitoring
Load, tyre type and tyre size settings are displayed:
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
251
If the tyres have not yet been registered dashes (-.-)
are displayed instead of the tyre pressures.
Displaying pressure difference
bb Vehicle is stationary.
e
e Setting e Vehicle eTyre pressure
monitoring e pressure deviation
Displaced are the required pressure and the pressure
deviation from the required pressure for each wheel
along with the load, tyre type and tyre size
information.
Example: If –0.1 bar (–1.5 psi) is displayed for the
rear right wheel, 0.1 bar (1.5 psi) must be added to
this tyre. The displayed pressures take into account
the tyre temperature.
e Always use the pressure deviation from the dis-
play or from the corresponding tyre pressure
warning to correct the tyre pressure.
If the tyres are not yet taught, the new required
pressures are displayed instead of the actual pres-
sure deviations.
Setting tyre type and tyre size
Information
The options available depend on the model and tyre
type. For this reason, some of the selection options
shown here may not be available.
e Before fitting tyres and wheels with dimensions
that are not available for selection in the TPM
menu, the missing information should be added.
Visit a qualified specialist workshop. Porsche
recommends a Porsche partner as they have
trained workshop personnel and the necessary
parts and tools.
e Use only tyres and wheels authorised by Porsche.
e
e Setting e Vehicle eTyre pressure
monitoring e tyre selection
Selecting full load or partial load
e
e Setting e Vehicle eTyre pressure
monitoring e full load
Full load
Full load is activated.
Full load
Partial load is activated.
e Adapt the tyre pressures to the selected load
type.
Information
If the option Full load is not displayed, the specified
tyre pressures are valid for all types of vehicle load.
Teaching in Tyre Pressure Monitoring
Tyre Pressure Monitoring begins to learn the tyres
after a wheel change, wheel transmitter replacement
or update of the tyre settings. During this process,
Tyre Pressure Monitoring recognises the wheels and
their locations. Position and pressure information is
displayed as soon as Tyre Pressure Monitoring has
assigned the wheels recognised as belonging to the
vehicle to the correct wheel positions.
During the learning process, the target pressures for
cold tyres (20 °C) are displayed on the central dis-
play and a message appears on the instrument
cluster.
The tyre pressure warning light
on the instru-
ment cluster remains lit until all the wheels have
been registered.
Inflating tyres
CAUTION
Hot filling hose
The compressor’s filling hose can get hot during the
inflation process and can cause burns.
e Wear gloves.
The compressor is housed in the right-hand box in
the front luggage compartment.
> Please refer to chapter "Luggage compartment"
on page 153.
> Read and follow the operating instructions on the
compressor.
1. Screw the compressor’s filler hose onto the tyre
valve.
2. Connect the compressor to a plug socket in the
vehicle and switch on the compressor.
The tyre is inflated.
3. Check inflation pressure using the pressure
gauge and reduce tyre pressure or add more air if
necessary. Check the inflation pressure again.
4. Switch off compressor.
5. Unscrew the compressor’s filler hose.
Information
The tyre pressure can also be checked at a service
station and the tyres can be inflated.
Reducing inflation pressure
1. Switch off compressor.
2. Open air bleed screw on the filler hose until the
correct inflation pressure is achieved.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
252
Reading off inscription on tyres
Fig. 212: Inscription on tyres
A Nominal width in mm
B Cross-section ratio in %
C Belt type code letter
D Rim diameter in inches
E Load rating code number
F Speed code letter
The speed code letter F indicates the maximum
permitted speed for the tyre.
H
up to 210 km/h (130 mph)
V
up to 240 km/h (150 mph)
W
up to 270 km/h (168 mph)
Y
up to 300 km/h (186 mph)
(Y) up to 300 km/h (186 mph) as for Y
tyres. Speeds of more than 300 km/h
(186 mph) are also possible at a max-
imum tyre load capacity of 85 % (con-
firmation from tyre manufacturer
required for speeds of more than
300 km/h (186 mph)).
Detecting tyre damage
WARNING
Hidden tyre damage and
rim flange damage
Hidden tyre damage can cause the tyre to burst. You
may lose control of the vehicle.
e Check tyres, including the sidewalls, regularly for
foreign bodies, nicks, cuts, cracks and bulges.
e Cross kerb edges slowly and at right angles if
possible. Avoid heavy or sharp-angled impact
against steep and sharp kerbs or sharp-edged
objects (e.g. stones).
e If in doubt, have the wheel – particularly the in-
ner side – checked by an expert. Visit a qualified
specialist workshop. Porsche recommends a
Porsche partner as they have trained workshop
personnel and the necessary parts and tools.
e Tyres must never be repaired under any circum-
stances. Sealing the tyre with the tyre sealant is
only an emergency solution to enable you to
drive to the nearest workshop.
In the case of the following tyre damage, the tyre
must be replaced for safety reasons:
– Tyre damage where the possibility of a ply frac-
ture cannot be ruled out.
– If the tyre has been thermally and mechanically
overloaded following a loss of pressure or other
previous damage.
Changing tyres and wheels
e Switch off the ignition when changing a wheel.
WARNING
Lack of grip
In the initial period, new tyres do not yet have their
full road-holding ability or grip.
e You should therefore drive at moderate speeds
during the first 200 km (125 miles) to extend
the service life of the tyres and achieve full per-
formance capability.
e Only fit tyres of the same make and type and
with the same specification number (e.g. "N...").
e Before fitting new tyres, inquire about their cur-
rent approval status: Contact your Porsche
partner.
e Use only tyre makes tested and approved by
Porsche.
e The deviation in tread depth on an axle must not
be more than 30 %.
e Only use second-hand tyres if you know their
history.
e Always replace both tyres on an axle so that dif-
ferent profile depths will not unnecessarily influ-
ence vehicle handling.
e Tyres should only be fitted by professionals. Visit
a qualified specialist workshop. Porsche recom-
mends a Porsche partner as they have trained
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
253
workshop personnel and the necessary parts and
tools.
e Adapt your driving style to the changed vehicle
handling.
e Only use tyres with tyre pressure sensors for Tyre
Pressure Monitoring (TPM).
e Make sure that the wheels are compatible with
the TPM system in the vehicle. For information
on suitable wheels and on the TPM system in the
vehicle: Contact your Porsche partner.
e When changing a tyre, check the battery charge
condition of the tyre pressure sensors: Visit a
qualified specialist workshop. Porsche recom-
mends a Porsche partner as they have trained
workshop personnel and the necessary parts and
tools.
> Please refer to chapter "Technical Data" on
page 308.
Information
If new tyres are fitted to only one axle, the different
tread depths on the two axles can cause a marked
change from the previous driving behaviour to which
you have become accustomed. This is particularly
true when new tyres are fitted to the rear axle. The
effect is reduced continuously, however, as tyre
mileage increases.
Checking and replacing valves and
valve caps
e Use only genuine Porsche valves for the Tyre
Pressure Monitoring (TPM) system.
e Check the valves whenever the tyres are
changed and replace them if necessary. Porsche
recommends a Porsche partner as they have
trained workshop personnel and the necessary
parts and tools.
If valve caps are missing, the valve is unprotected
from dust and dirt, resulting in leaks.
e Always screw on valve caps tightly to protect
valve inserts from dirt. Dirty valve inserts can
cause creeping air loss.
e Replace missing valve caps immediately.
e Use only plastic valve caps.
Using winter tyres
WARNING
Exceeding the maximum
permitted speed
Exceeding the maximum permitted speed can cause
tyres to burst.
e Observe the maximum permitted speed for the
tyre.
e Only fit winter tyres rated for a lower permitted
top speed than the specified maximum vehicle
speed if they bear the M+S designation or the
snowflake symbol on the tyre sidewall. Observe
country-specific laws.
e Affix a sticker showing the maximum permitted
speed in the driver’s field of vision. Observe
country-specific laws.
e Set the maximum permitted speed as the speed
limit.
e Install winter tyres in a timely manner before the
cold season begins.
e Use only tyre makes tested and approved by
Porsche.
e Before fitting new tyres, inquire about their cur-
rent approval status: Contact your Porsche
partner.
Information
At low temperatures, juddering noises caused by the
tyres can occur during manoeuvering or accelerating
out of curves on both dry and wet road surfaces.
The driving performance and comfort of summer
tyres is reduced at low temperatures below 7 °C.
Porsche therefore recommends that you fit winter
tyres on the vehicle when temperatures are below
7 °C.
Extremely low temperatures below –15 °C can
cause permanent damage to summer tyres.
Winter tyres are no longer suitable if their tread
depth is less than 4 mm.
Using snow chains
Snow chains can be fitted to the rear axle only, with
the tyre/wheel combinations listed under "Technical
Data" and marked for snow chain use.
> Please refer to chapter "Technical Data" on
page 308.
e Use only the snow chains approved by Porsche
to guarantee sufficient clearance between the
wheel well and the chain.
e Remove ice and snow deposits in the wheel well
before installing the chains.
e Vehicles with rear axle steering: Deactivate rear
axle steering.
–
e Setting e Vehicle settings e Addi-
tional chassis settings
e Observe the different national regulations re-
garding maximum speeds.
Checking tyre tread
Most tyres have integrated wear indicators in the
centre of the tread. These wear indicators are
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
254
located in the main tread channels and display the
minimum tread depth of 1.6 mm.
e Check the tyre tread regularly, particularly before
and after long journeys.
Measuring the tyre tread depth
e Insert a commercially available tread depth
gauge or calliper in the tyre tread and measure
the tyre tread depth.
Information
Uneven tyre wear indicates a defect on the vehicle:
e Visit a qualified specialist workshop. Porsche
recommends a Porsche partner as they have
trained workshop personnel and the necessary
parts and tools.
Storing wheels
Tyres must not be more than 6 years old. Chemical
additives, which make the rubber in the tyre elastic,
lose their effect over the course of time and the
rubber becomes brittle. The age of a tyre can be
seen from the DOT code on the tyre sidewall. If the
last four digits are 3016, for example, the tyre was
manufactured in the 30th week of 2016.
e Always store wheels in cool, dry and dark condi-
tions. Tyres without rims should be stored in a
standing position.
e Do not store summer tyres or park vehicles fitted
with summer tyres at ambient temperatures be-
low –15 °C.
e Avoid contact with petrol, oil and grease.
Balancing wheels
As a precaution, have wheels balanced in spring
(summer tyres) and before winter (M+S tyres).
e Visit a qualified specialist workshop. Porsche
recommends a Porsche partner as they have
trained workshop personnel and the necessary
parts and tools.
Changing a wheel
WARNING
Working under the
vehicle
The vehicle can slip off the jack.
e Make sure that no one is in the vehicle when
jacking up and changing a wheel.
e Raise the vehicle only at the prescribed jacking
points on the vehicle underbody.
e Never jack up the vehicle when it is parked on a
surface that slopes up, down or to the side.
e Only use the jack to raise the vehicle for chang-
ing wheels.
e Always place the vehicle on solid supports when
working under the vehicle.
> Please refer to chapter "Jack and Lifting Plat-
form" on page 138.
Information
The tools needed for changing wheels (jack, wheel
bolt wrench, mounting aids, etc.) are not included in
the standard scope of supply for the vehicle.
e For information on the tool required: Contact
your Porsche partner.
Information
The tyre and wheel sizes are different on each of the
two axles. When wheels are removed, mark the di-
rection of rotation and position of each wheel and fit
the wheels in accordance with this marking.
e Only use wheels/tyres with approved dimensions
for each axle.
Vehicle registration documents or Please refer to
chapter "Technical Data" on page 308.
Caring for wheel attachment faces
Fig. 213: Wheel attachment faces
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
255
NOTICE
Risk of damage to the wheel and wheel attachment
face.
e The wheel attachment face B on the brake disc
and on the wheel hub itself must not be greased.
e Only the areas A may be greased. Grease these
areas very thinly with Optimoly
®
TA: Contact your
Porsche partner. Do not use any other grease or
paste.
Caring for wheel bolts
e Always clean the wheel bolts before fitting.
e Wheel bolts must not be greased.
e Replace damaged wheel bolts. Only use genuine
Porsche wheel bolts intended for this particular
model or wheel bolts of similar quality which
have been manufactured according to Porsche
specifications and production requirements.
e Tighten wheel bolts to a tightening torque of
160 Nm (118 ftlb.).
e Do not use any force-activated tools such as
impact screwdrivers.
Using security wheel bolts
Fig. 214: Adapter for security wheel bolts
The adapter for the security wheel bolts is located in
the tool kit.
e To loosen and tighten the wheel bolt with an-
titheft protection, the adapter must be used be-
tween the wheel bolt and the wheel bolt wrench.
e When positioning the adapter ensure that it en-
gages fully in the teeth of the wheel bolt.
Changing a wheel
Preparing the vehicle
WARNING
Control operation of the
levelling system
A vehicle on which the levelling system is activated
can move unexpectedly or tip or fall off lifting
equipment, e.g. a jack or lifting platform. This can
result in serious injury and damage.
e Manually set Normal Level and switch off the
levelling system before lifting the vehicle.
e
e Setting e Vehicle e Additional chassis
settings e Deactivate chassis adjustment
before using a jack
1. Activate the electric parking brake.
2. Turn off the vehicle.
3. Secure the vehicle to prevent it from rolling
away, e.g. by placing wheel chocks at the wheels
on the opposite side.
4. Slightly loosen the wheel bolts or wheel nuts on
the wheel to be changed.
5. Lift the vehicle only at the specified jacking
points.
> Please refer to chapter "Jack and Lifting
Platform" on page 138.
6. Raise the vehicle until the wheel lifts off the
ground.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
256
Changing a wheel
Fig. 215: Screw in one assembly aid on vehicles without
PCCB
Fig. 216: Screw in two assembly aids on vehicles with PCCB
1. For vehicles without PCCB: Remove one wheel
bolt and screw in one assembly aid.
– or –
1. For vehicles with PCCB: Remove two wheel bolts
and screw in two assembly aids A and B.
NOTICE
The brake discs can become damaged in the case of
improper wheel change, especially in vehicles with
PCCB.
e Screw in assembly aids when changing a wheel.
2. Remove the remaining wheel bolts.
3. Remove the wheel.
4. Fit a new wheel.
5. Insert wheel bolts and tighten slightly in diago-
nally opposite sequence.
6. Remove assembly aids and screw in remaining
wheel bolts. Initially tighten wheel bolts only
slightly in diagonally opposite sequence so that
the wheel is centred.
7. Inflate the tyre if necessary.
8. Lower the vehicle fully and remove the jack.
9. Tighten the wheel bolts in diagonally opposite
sequence. Do not use any force-activated tools
such as impact screwdrivers.
10.Immediately after changing a wheel, use a tor-
que wrench to check the prescribed tightening
torque of the wheel bolts (1600 Nm /
1180 ftlb.).
11.The settings for Tyre Pressure Monitoring (TPM)
are updated.
> Please refer to chapter "Teaching in Tyre
Pressure Monitoring" on page 251.

Related Topics

Popular Owner Manuals