Get Getting to know your vehicle Guide for Renault Clio 4 Door Fifth Generation (2019-2025)

Section 1: Getting to know your Vehicle

Key, radio frequency remote control: general information, use, deadlocking . . . . . . . . . . . . . . . . . .

Card: general information, use, deadlocking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2

1.6

Locking, unlocking the opening elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.14

Opening and closing the doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.18

Automatic locking when driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.20

Seat belts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.23

Additional methods of restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.28

in addition to the front seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

to the rear seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.28

1.34

1.35

Child safety: general information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.37

choosing a child seat mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

fitting a child seat, general information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.40

1.43

Child seats: attachment by seat belt or by Isofix system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.45

deactivating, activating the front passenger airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.57

Driving position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.60

Instrument panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.64

Displays and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.70

trip computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

vehicle settings customisation menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.77

1.89

Clock and outdoor temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.92

Steering wheel, Power-assisted steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.94

Rear view mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.96

Headrests - Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.98

Exterior lighting and signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.99

Audible and visual signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.105

Headlight beam adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.106

Washers, wipers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.107

Fuel tank (filling with fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.114

Reagent tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.119

1.1

KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2)

3

2

1

Driver’s responsibility

when parking or stopping

the vehicle

2

1

4

Never leave an animal,

child or adult who is not self-suffi-

cient alone on your vehicle, even for

a short time.

5

They may pose a risk to themselves

or to others by starting the engine,

activating equipment such as the

electric windows or locking the

doors.

1 Locks all the opening elements.

2 Unlocks all the opening elements.

3 Driver’s door and ignition/starter key.

Also, in hot and/or sunny weather,

please remember that the tempera-

ture inside the passenger compart-

ment increases very quickly.

5 Unlocking the luggage compartment

only.

Remote control with switchblade

key:

4 Locking/unlocking using the switch-

blade key. To release the insert from

its housing, press button 4, it comes

out automatically. Press button 4 and

guide the insert back into its housing.

Advice

RISK OF DEATH OR SERIOUS

INJURY.

Avoid leaving the remote control in

hot, cold or humid areas.

The key must not be used for any

function other than those described

in the handbook (removing the cap

from a bottle, etc.).

1.2

KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2)

Radio frequency remote

control operating range

This varies according to the surround-

ings: take care not to lock or unlock the

doors by inadvertently pressing the but-

tons on the remote control.

Note: if a door or the boot is open or not

properly shut, locking is not carried out.

A beep sounds and the hazard warning

Replacement and additional keys

lights and side repeaters do not flash.

or remote controls.

Interference

You must only contact an approved

dealer:

Interference by factors in the immediate

vicinity (external installations or the use

of equipment operating on the same

frequency as the remote control) may

affect the operation of the remote con-

trol.

– If you need to replace a key it will

be necessary to take the vehicle

and all of its keys to an approved

Dealer in order to initialise the

system.

– Depending on the vehicle, you

have the option of using up to

four remote controls.

Remote control unit failure

Make sure that the correct battery

type is being used, and that the

battery is in good condition and in-

serted correctly. These batteries

have a service life of approximately

two years.

How to change the battery ➥ 5.20.

1.3

RADIO FREQUENCY REMOTE CONTROL: use

The remote control A can be used to

lock or unlock the doors and boot.

Unlocking the doors

Pressing button 2 unlocks the doors

and tailgate.

Unlocking is indicated by one flash of

the hazard warning lights and the indi-

cator lights.

A

It is powered by a battery which can be

replaced. ➥ 5.20.

2

Locking the doors

1

Note: with the ignition on and the

engine running ➥ 2.3, buttons on the

remote control are not activated.

Press locking button 1.

2

The side indicator lights and hazard

warning lights flash twice to indicate

that the doors have been locked.

1

3

Unlocking the boot only

Press and hold button 3. The luggage

compartment opens very slightly.

Pressing the 1 button twice locks the

vehicle and enables the closure of the

front and rear windows (depending on

the vehicle).

3

Note: if a door or the boot is open or not

properly shut, locking is not carried out.

A beep sounds and the hazard warning

lights and side repeaters do not flash.

Driver’s responsibility when parking or stopping the vehicle

Never leave an animal, child or adult who is not self-sufficient alone on

your vehicle, even for a short time.

They may pose a risk to themselves or to others by starting the engine,

activating equipment such as the electric windows or locking the doors.

Also, in hot and/or sunny weather, please remember that the temperature inside

the passenger compartment increases very quickly.

RISK OF DEATH OR SERIOUS INJURY.

Depending on the vehicle, the door

mirrors fold in/out automatically

when the vehicle is locked/unlocked

➥ 1.96.

1.4

RADIO FREQUENCY REMOTE CONTROL UNIT: deadlocking

If the vehicle is equipped with a dead-

locking function, this allows you to lock

the opening elements and to prevent

the doors from being unlocked using

the interior handles (for example, by

breaking the window and then trying to

open the door from the inside).

1

To do this, press button 1 twice in quick

succession.

1

The hazard warning lights and side in-

dicator lights give two slow flashes and

three quick flashes to indicate locking.

Depending on the vehicle, the door mir-

rors fold in automatically when the vehi-

cle is locked ➥ 1.96.

Never use deadlocking if

someone is still inside the

vehicle.

1.5

CARD: general information (1/3)

The card is used for:

card operating range

– locking/unlocking the doors and tail-

gate (doors, tailgate) and the fuel

filler flap (see the following pages);

– switching on the vehicle lighting re-

motely (refer to the following pages);

– automatic remote closing of the elec-

tric windows ➥ 3.20;

This varies according to the environ-

ment: take care not to accidentally lock

or unlock the vehicle by inadvertently

pressing the buttons on the card.

1

4

Note: if a door or the boot is open or not

properly shut, locking is not carried out.

A beep sounds and the hazard warning

lights and side repeaters do not flash.

2

3

– starting the engine ➥ 2.6.

Battery life

Interference

Make sure that the correct battery type

is being used, and that the battery is in

good condition and inserted correctly.

Its service life is approximately two

years: it should be replaced when the

message “Keycard Battery Low” ap-

pears on the instrument panel ➥ 5.22.

Interference by factors in the immediate

vicinity (external installations or the use

of equipment operating on the same

frequency as the card) may disrupt its

operation.

1 Unlocking the doors and tailgate.

2 Locking all doors and tailgate.

3 Unlocking the luggage compartment

only.

4 Switching on the lighting remotely.

When the battery is flat, you can still

lock/unlock and start your vehicle.

➥ 1.14 ➥ 2.6.

1.6

CARD: general information (2/3)

Advice

4

Avoid leaving the card in hot, cold or

humid areas.

Do not keep the card in a place

where it could be bent or dam-

aged accidentally, such as in a back

pocket of a garment.

Driver’s responsibility

when parking or stopping

the vehicle

Never leave an animal,

child or adult who is not self-suffi-

cient alone in your vehicle, even for

a short time.

They may pose a risk to themselves

or to others by starting the engine,

activating equipment such as the

electric windows or locking the

doors, for example.

Distance lighting function

Pressing button 4 switches on the

dipped beam headlights and the exte-

rior lighting for approximately 20 sec-

onds. This can be used, for example,

to identify the vehicle from a distance

when parked in a car park.

Replacement: need for an

additional card

Also, in hot and/or sunny weather,

please remember that the tempera-

ture inside the passenger compart-

ment increases very quickly.

If you lose your card or require an-

other, you can obtain one from an

authorised dealer.

Pressing and holding the 4 button for

approximately two seconds activates

the exterior lighting and a sound is

emitted.

If a card is replaced, it will be neces-

sary to take the vehicle and all its

cards to an approved Dealer to ini-

tialise the system.

RISK OF DEATH OR SERIOUS

INJURY.

Note: pressing button 4 again switches

off the lighting.

You may use up to four cards per

vehicle.

1.7

CARD: general information (3/3)

5

A

7

8

6

Insert the strap into the 8 component

and pass the end of the strap through

the buckle.

Fitting a strap 7

Slide the rear casing 5 downwards

while pressing on zone A.

Position the strap at the 6 opening and

close the cartridge.

Note: check that the diameter of the 7

strap cord fits the 6 opening.

1.8

“HANDS-FREE” CARD: use (1/4)

Deactivating/activating the

“hands-free” mode

Depending on the vehicle, you can de-

activate/activate:

– unlocking when approaching and

locking when moving away from the

vehicle;

Never leave your vehicle

with the card inside.

1

– locking and unlocking by pressing on

the buttons on the door handle.

You can also disable/activate the

sound signal that is emitted upon lock-

ing when moving away from the vehi-

cle ➥ 1.89.

Driver’s responsibility

when parking or stopping

the vehicle

2

Never leave an animal,

child or adult who is not self-suffi-

cient alone in your vehicle, even for

a short time.

They may pose a risk to themselves

or to others by starting the engine,

activating equipment such as the

electric windows or locking the

doors, for example.

Depending on the vehicle, there are

two or three ways to unlock/lock the ve-

hicle:

– “hands-free”, when approaching and

moving away from the vehicle;

– “hands-free”, using the 2 button on

the 1 handle of one of the front doors;

– using the card in remote control

mode.

Also, in hot and/or sunny weather,

please remember that the tempera-

ture inside the passenger compart-

ment increases very quickly.

RISK OF DEATH OR SERIOUS

INJURY.

Do not store the card anywhere it

may come into contact with other

electronic equipment (computer,

phone etc.) as this could hinder its

operation.

1.9

“HANDS-FREE” CARD: use (2/4)

5

3

4

If the card has been within the detection

area 3 for approximately 15 minutes,

remote locking is disabled. To lock the

vehicle, press the 5 button or, depend-

ing on the vehicle, the 2 button on the 1

handle.

Hands-free unlocking, when

approaching the vehicle

With the card in access zone 3, the ve-

hicle will unlock. Unlocking is indicated

by one flash of the hazard warning

lights and the indicator lights.

Hands-free locking when

moving away from the

vehicle

With the card on you, doors and lug-

gage compartment door closed, move

away from the vehicle: it will lock auto-

matically once you have left the access

zone 3.

The vehicle cannot be remotely locked

if the card is within the area 4.

Note: the distance at which the vehicle

locks depends on the surroundings.

To indicate that the vehicle has been

locked, the hazard warning lights

flash twice and then light up for ap-

proximately four seconds, and a beep

sounds in confirmation.

Depending on the vehicle, the door

mirrors fold in/out automatically

when the vehicle is locked/unlocked

➥ 1.96.

1.10

“HANDS-FREE” CARD: use (3/4)

To indicate that the vehicle has been

locked, the hazard warning lights flash

twice and then light up for approxi-

mately four seconds.

1

Special features of the

unlocking system

Under certain circumstances, approach

unlocking is deactivated:

4

– after eight days of no use of the vehi-

cle;

2

– if the card remains close to the 3

area of the vehicle for approximately

five minutes after the vehicle has

been locked;

“Hands-free” unlocking/

locking using button 2

(depending on the vehicle)

Special features relating to

“hands-free” locking

After locking in “hands-free” mode, you

have to wait approximately three sec-

onds to be able to unlock the vehicle

again. During these three seconds, the

door handles can be tried to make sure

that the vehicle is locked properly.

– after several passes in the vicinity of

the 3 area of the vehicle and without

the door being unlocked.

With the card in zone 3 and the vehi-

cle locked, press the button 2 on the

handle 1 of one of the two front doors:

the vehicle unlocks. Press the button 2

also unlocks all the doors and the tail-

gate.

Use the remote control card or, depend-

ing on the vehicle, press the 2 button on

the door handle 1 to unlock the vehicle

and reactivate the mode.

Note: if a door or the boot is open or not

properly shut, locking is not carried out.

A beep sounds and the hazard warning

lights and side repeaters do not flash.

Unlocking is indicated by one flash of

the hazard warning lights and the indi-

cator lights.

Pressing the 2 button again locks the

vehicle.

1.11

“HANDS-FREE” CARD: use (4/4)

Locking using the card

With the doors and boot closed, press

button 5: the vehicle locks.

5

7

To indicate that the vehicle has been

locked, the hazard warning lights flash

twice and then light up for approxi-

mately four seconds.

Pressing the 5 button twice locks the

vehicle and enables the closure of the

front and rear windows (depending on

the vehicle).

6

4

Note:

– the maximum distance at which the

vehicle locks depends on the sur-

roundings;

If, while the engine is running, a door

is opened and closed, and the card is

no longer in the zone 4, the message

“Keycard Not Detected” indicates that

the card is not inside the vehicle. This

will, for example, prevent you from driv-

ing away after dropping off a passenger

who has kept the card on them.

Using the card as a remote

control

– if a door or the boot is open or not

properly shut, locking is not carried

out. A beep sounds and the hazard

warning lights and side repeaters do

not flash.

Unlocking with the card

Press button 7.

Unlocking is indicated by one flash of

the hazard warning lights and the indi-

cator lights.

The warning disappears when the card

is detected again.

Unlocking the boot only

Press and hold button 6. The boot

opens slightly.

The card buttons are deactivated

when the engine is running.

1.12

“HANDS-FREE” CARD: DEADLOCKING

If the vehicle is equipped with a dead-

locking function, this allows you to lock

the opening elements and to prevent

the doors from being unlocked using

the interior handles (for example, by

breaking the window and then trying to

open the door from the inside).

1

To do this, press button 1 twice in quick

succession.

Locking is confirmed by two slow

flashes and three quick flashes of

the hazard warning lights and indicator

lights.

Depending on the vehicle, the door mir-

rors fold in automatically when the vehi-

cle is locked ➥ 1.96.

Never use deadlocking if

someone is still inside the

vehicle.

1.13

LOCKING, UNLOCKING THE DOORS (1/4)

If the remote control or,

depending on the vehicle, the

card does not work

2

1

In some cases, the radio frequency

remote control or the card may not

work:

A

– card/radio frequency remote control

battery worn or run flat, vehicle bat-

tery flat etc.

– use of appliances operating on the

same frequency as the card (mobile

phone, etc.);

– vehicle located in a high electromag-

netic radiation zone.

It is then possible:

The card’s built-in key

The 2 integrated key can be used to

lock or unlock the driver’s door when

the card is not working.

– to use the radio frequency remote

control or the emergency key inte-

grated into the card (depending on

the vehicle) to unlock the driver’s

door;

– to use the interior door locking/un-

locking control (refer to the following

pages).

Access with key 2

Slide the rear casing 1 downwards

while pressing on zone A.

1.14

LOCKING, UNLOCKING THE DOORS (2/4)

B

3

2

4

Using the key integrated in

the card

Vehicles with key/remote

control

– Insert the tip of the key 2 into the

notch 3 at the bottom of the cover B

on the driver’s door;

– Move it upwards to remove the

cover B;

– insert the key 2 into the lock of the

driver’s door, lock and unlock.

Using the key

– Insert the tip of the key 4 into the

notch 3 at the bottom of the cover B

on the driver’s door;

– Move it upwards to remove the

cover B;

– insert the key 4 into the lock of the

driver’s door, lock and unlock.

Once you are inside the vehicle, put the

key back in its casing in the card.

1.15

LOCKING, UNLOCKING THE DOORS (3/4)

6

5

Locking the doors manually

Turn screw 5 with the door open (using

Interior locking/unlocking

door control

the end of the key) and close the door.

Switch 6 controls the doors, the boot

and the fuel filler flap simultaneously.

This means that the doors are then

locked from the outside.

If a door or the tailgate is open or not

closed properly, the doors and tailgate

lock/unlock quickly.

The doors may then only be opened

from the inside or by using the key in

the driver’s door.

If transporting an object with the tail-

gate open, you can still lock the doors:

with the engine stopped, press and

hold switch 6 to lock the other doors.

1.16

LOCKING, UNLOCKING THE DOORS (4/4)

Door and tailgate status

indicator

When the ignition is on, the 6 switch

warning light indicates the locking

status of the opening elements:

Locking the opening

elements without the card or

the key

For example, in the event of a dis-

charged battery or the card or key tem-

porarily not working etc.

– indicator light on, the doors and tail-

gate are locked;

With the engine switched off and a

door or tailgate open, press and hold

the 6 switch for more than five seconds.

– indicator light off, the doors and tail-

gate are unlocked.

When the door is closed, all the doors

and the tailgate will be locked.

When you lock the doors, the indicator

light remains lit and then goes out.

Note: unlocking the vehicle from the

outside is only possible with the card in

the vehicle’s access zone or using the

key.

Driver’s responsibility

If you decide to keep the

doors locked when you are

driving, remember that it

Never leave your vehicle

with the key or card inside.

may be more difficult for those as-

sisting you to gain access to the

passenger compartment in the

event of an emergency.

1.17

OPENING AND CLOSING THE DOORS (1/2)

3

2

1

Rear doors

Opening the doors from the

Opening from the inside

outside

With the doors unlocked, pull handle 2.

Pull handle 3.

Front doors

With the doors unlocked or the card on

you, hold the 1 handle and pull towards

you.

As a safety precaution,

the doors should only be

opened or closed when the

vehicle is stationary.

1.18

OPENING AND CLOSING THE DOORS (2/2)

Lights-on reminder buzzer

If you have switched off the ignition

and left the lights switched on, a re-

minder buzzer will sound when a door

is opened.

Door/tailgate open buzzer

Driver’s responsibility

when parking or stopping

the vehicle

When the vehicle is stationary, the

2

4

warning light appears on the instrument

panel accompanied by a warning light

indicating which of the opening ele-

ments (door(s), luggage compartment)

are open or incorrectly closed.

Never leave an animal,

child or adult who is not self-suffi-

cient alone on your vehicle, even for

a short time.

They may pose a risk to themselves

or to others by starting the engine,

activating equipment such as the

electric windows or locking the

doors.

Also, in hot and/or sunny weather,

please remember that the tempera-

ture inside the passenger compart-

ment increases very quickly.

RISK OF DEATH OR SERIOUS

INJURY.

Once the vehicle reaches a speed

of approximately 6 mph (10 km/h), a

warning light indicates if the door(s)

or luggage compartment are open

or not properly closed, along with the

message “WARNING: Boot Open” or

“WARNING: Door Open” and a beep

will sound for around 40 seconds or

until the door/luggage compartment is

closed.

Child safety

Move lever 4 and check from the inside

that the doors are securely locked, to

prevent the rear doors being opened

from the inside.

1.19

AUTOMATIC LOCKING WHEN DRIVING

NB: if a door is opened or closed, it

Operating faults

will automatically lock again when the

vehicle reaches a speed of 6 mph (10

km/h).

If you experience an operating fault (no

automatic locking, the 1 switch warning

light does not illuminate when the doors

and luggage compartment are locked

etc.), make sure that automatic lock-

ing has not been deactivated by mis-

take and check that the doors and lug-

gage compartment are properly closed.

If they are properly closed, contact an

approved dealer.

1

Activating/deactivating the

function

To activate: with the vehicle station-

ary and the engine running, press the 1

switch until a beep sounds.

To deactivate: with the vehicle station-

ary and the engine running, press the

switch 1 until you hear two beeps.

The function can also be activated and

deactivated via the multimedia screen

(depending on the vehicle). ➥ 1.89.

Operating principle

After the vehicle is started, the system

automatically locks the doors when you

are driving at approximately 6 mph (10

km/h) and over.

The door can be unlocked:

– by pressing the central door unlock-

ing switch 1;

– at a standstill, by opening a front

door from inside the vehicle.

Driver’s responsibility

If you decide to keep the

doors locked when you are

driving, remember that it

may be more difficult for those as-

sisting you to gain access to the

passenger compartment in the

event of an emergency.

1.20

FRONT SEATS (1/2)

To tilt the seatback

Lift the 2 or 4 handle and tilt the seat-

back to the desired position. Release

the handle at the desired position and

make sure that it is locked.

5

4

3

1

2

After making adjustments,

make sure that the seat-

backs are correctly locked

in place.

To move the seat forwards or

backwards

Lift and hold the handle 1 to unlock the

seat. Release the handle once the seat

is in the correct position and ensure

that the seat is locked.

Central armrest 5

For safety reasons, carry

out any adjustments

when the vehicle is not

being driven.

(depending on the vehicle)

To adjust the position of the armrest,

slide it forwards or backwards until it

reaches the stop.

We would advise you not to recline

the seatbacks too far to ensure that

the effectiveness of the seat belts is

not reduced.

To raise or lower the seat

base

Move the lever 3 as many times as nec-

essary upwards or downwards until the

required position is reached.

Nothing should be placed on the

floor (area in front of driver) as such

objects may slide under the pedal

during braking manoeuvres, thus

obstructing its use.

1.21

FRONT SEATS (2/2)

Operating faults

When an operating fault is detected,

the warning lights of the 6 switch for the

seat concerned go out after approxi-

mately five seconds.

Consult an approved dealer.

6

Heated seats

With the ignition on:

– Pressing the switch 6 on the required

seat for the first time activates the

heating system on high. Both inte-

grated switch warning lights come

on;

– pressing the switch for the second

time changes the heating to low. One

integrated warning light comes on;

– pressing for the third time turns the

heating off.

1.22

SEAT BELTS (1/5)

Always wear your seat belt when trav-

elling in your vehicle. You must also

comply with the legislation of the par-

ticular country you are in.

Adjusting your driving

position

– Sit well back in your seat (having

first removed your coat or jacket).

This is essential to ensure your back

is positioned correctly;

Before starting, first adjust your driv-

ing position, then ask all occupants

to adjust their seat belts to ensure

optimum protection.

– adjust the distance between the

seat and the pedals. Your seat

should be as far back as possible

while still allowing you to fully de-

press the pedals. The seatback

should be adjusted so that your arms

are slightly bent when you hold the

steering wheel;

Make sure that the rear bench seat

is locked in position correctly so that

the rear seat belts will operate cor-

rectly. ➥ 3.34.

– adjust the position of your head-

rest. For maximum safety, your head

must be as close as possible to the

headrest;

Incorrectly adjusted or

twisted seat belts may

cause injuries in the event

of an accident.

– adjust the height of the seat. This

adjustment allows you to select the

seat position which offers you the

best possible view;

Use one seat belt per person,

whether child or adult.

– adjust the position of the steering

wheel.

Even pregnant women should wear

a seat belt. In this case, ensure that

the lap belt is not exerting too much

pressure on the abdomen, but do

not allow any slack.

1.23

SEAT BELTS (2/5)

Locking

Unwind the belt slowly and smoothly

and ensure that buckle 3 locks into

catch 5 (check that it is locked by pull-

ing on buckle 3).

If the belt jams, allow it to return slightly

before attempting to unwind it again.

1

If your seat belt is completely jammed,

pull slowly, but firmly, so that just over

3 cm unwinds. Allow it to return slightly

before attempting to unwind it again.

3

4

If there is still a problem, contact an ap-

proved dealer.

5

2

Adjusting the seat belts

Unlocking

Sit with your back firmly against the

seatback.

Press button 4 and the seat belt will be

rewound by the inertia reel. Guide the

belt.

Shoulder strap 1 should be as close as

possible to the base of the neck but not

on it.

Lap belt 2 should be worn flat over the

thighs and against the pelvis.

The belt should be worn so that it is

as close as possible to your body, i.e.:

avoid wearing heavy clothing or keep-

ing bulky objects under the belts, etc.

1.24

SEAT BELTS (3/5)

Driver’s seat belt reminder

and, depending on the vehi-

cle, front passenger seat belt re-

minder

It is accompanied by the 6 symbol which

appears for approximately 60 seconds

each time one of the rear seat belts is

fastened or unfastened.

ß

This appears on the central display

when the ignition is switched on and

if the driver’s and/or front passenger’s

seat belt(s) (if the passenger seat is

occupied) is not fastened. Depending

on the vehicle, if the seat is occupied

and one of these seat belts is not fas-

tened or becomes unfastened while

the vehicle is moving at a speed over

approximately 12 mph (20 km/h), the

When the vehicle speed reaches or ex-

ceeds 12 mph (20 km/h), if one of the

rear seat belts is or becomes unfas-

tened during the journey:

– the

the central display;

™

warning light flashes on

6

and

– a beep is emitted for 30 to 120 sec-

onds (depending on the version);

™

warning light flashes and a beep

sounds for approximately 120 seconds.

and

playback of 6 graphic:

– indicator green: seatbelt fastened;

– indicator in red: the seat is occupied

and the seat belt is not fastened;

– indicator grey: seat not occupied.

– the 6 symbol is displayed for at least

approximately 60 seconds and

the symbol for the seat concerned

changes to red.

Note: an object placed on the passen-

ger seat may activate the warning light

in some cases, depending on the ve-

hicle.

Always make sure that the rear pas-

sengers are properly fastened and that

the number of fastened seat belts in-

dicated corresponds to the number of

rear seats occupied.

Depending on the vehicle, the

™

Rear seat belt reminder (depending

on the vehicle)

The 6 graphic is displayed on the in-

strument panel when the ignition is

switched on. This informs the driver of

the fastening status of each of the rear

seat belts every time:

– the ignition is switched on;

– a door is opened;

– fastening or unfastening of a rear

seat belt.

warning light on the central display also

appears when the ignition is switched

on, if a rear seat is occupied and the

seat belt is not fastened. When the ve-

hicle speed is less than approximately

Note: in some cases the alerts may be

activated if an object is placed on one

of the rear seats, depending on the ve-

hicle.

12 mph (20 km/h), the

light on the central display appears

when a rear seat belt is unfastened.

™

warning

1.25

SEAT BELTS (4/5)

7

8

Adjusting the height of the

front seat belts

Use button 7 to adjust the seat belt

height so that the shoulder strap is worn

as shown previously. Press the button 7

and raise or lower the seat belt. Make

sure that the seat belt is locked in posi-

tion correctly after you have adjusted it.

Rear seat belts 8

The belts are locked, unlocked and

adjusted in the same way as the front

belts.

Check that the rear seat

belts are positioned and

operating correctly each

time the rear bench seat is

moved.

1.26

SEAT BELTS (5/5)

The following information applies to the vehicle’s front and rear seat belts.

– No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and

their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer.

– Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too

loosely may cause injury in the event of an accident.

– Never wear the shoulder strap under your arm or behind your back.

– Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt around

them.

– The belt should never be twisted.

– Following an accident, have the seat belts checked and replaced if necessary. Always replace your seat belts as soon as

they show any signs of wear.

– When the rear bench seat is being put back, make sure that the seat belts and buckles are correctly positioned so that they

can be used properly.

– Make sure that the buckle is inserted into the appropriate catch.

– Ensure that no objects are placed in the area around the seat belt catch as they could prevent it from being properly secured.

– Make sure the seat belt catch is properly positioned (it should not be hidden away, crushed or flattened by people or ob-

jects).

1.27

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/6)

Depending on the vehicle, they will con-

sist of:

– Have the entire restraint

system checked following

an accident.

– seat belt inertia reel pretension-

ers;

– No operation whatso-

ever is permitted on any part

of the system (pretensioners,

airbags, computers, wiring) and

the system components must not

be reused on any other vehicle,

even if identical.

– central seat belt pretensioners;

– chest-level load limiters;

– airbags driver and passenger

front.

These systems are designed to act in-

dependently or together when the vehi-

cle is subjected to a frontal impact.

– Only qualified personnel from our

Network may work on the airbags;

otherwise the system may trigger

accidentally and cause injury.

2

Depending on the severity of the

impact, the system can trigger:

1

– The electric trigger system may

only be tested by a specially

trained technician using special

equipment.

– seat belt locking;

Pretensioners

– the seat belt inertia reel pretensioner

(which engages to correct seat belt

slack);

The pretensioners hold the seat belt

against the body, holding the occupant

more securely against the seat, thus in-

creasing the seat belt’s efficiency.

– When the vehicle is scrapped,

contact an approved dealer for

disposal of the pretensioner and

airbags gas generators.

– lap seat belt pretensioners to hold

the occupant in their seat;

In the event of a severe frontal impact

and if the ignition is switched on, the

system may engage the following de-

pending on the force of the impact:

– the front airbag.

– the seat belt inertia reel preten-

sioner 1 which instantly retracts the

seat belt;

– the lap seat belt inertia reel preten-

sioner 2 on the front seats.

1.28

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/6)

Load limiter

driver and passenger front

Airbags

Fitted to the driver and passenger

sides.

Above a certain severity of impact, this

mechanism is used to limit the force of

the belt against the body so that it is at

an acceptable level.

A symbol on the lower section of the

windscreen indicates if this equipment

is present (depending on the vehicle).

Each airbag system consists of:

– an airbag and gas generator fitted on

the steering wheel for the driver and

in the dashboard for the passenger;

– an electronic unit for monitoring the

system controlling the gas generator

electrical trigger;

– remote sensors;

– a single warning light

instrument panel.

å

on the

The airbag system uses py-

rotechnic principles. This

explains why, when the

airbag inflates, it will gener-

ate heat, produce smoke (this does

not mean that a fire is about to start)

and make a banging noise. In a situ-

ation where an airbag is required, it

will inflate immediately and this may

cause some minor, superficial graz-

ing to the skin or other problems.

1.29

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/6)

Operating faults

å

This warning light comes on

when the engine is started and then

goes out after approximately three sec-

onds.

If it does not come on when the ignition

is switched on or if it stays on, there is a

fault in the system.

Contact your approved Dealer as soon

as possible.

Your protection will be reduced until this

fault is rectified.

Operation

This system is only operational when

the ignition is switched on.

In a severe frontal impact, the airbags

inflate rapidly, cushioning the impact

of the driver's head and chest against

the steering wheel and of the front pas-

senger against the dashboard. The air

bags then deflate immediately so that

the passengers are not in any way hin-

dered from leaving the vehicle.

1.30

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/6)

The following cases trigger the pre-

tensioners or airbags.

In a frontal impact with another vehi-

cle of an equivalent or higher category,

with an impact area equal to or greater

than 40%, where the speed of both ve-

hicles is equal to or greater than

25 mph (40 km/h).

In a side impact with another vehicle

of an equivalent or higher category, at

an impact speed equal to or greater

than 31 mph (50 km/h).

In a frontal impact against a rigid

(non-deformable) surface at an impact

speed equal to or greater than 16 mph

(25 km/h).

1.31

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (5/6)

In the following examples, the pre-

tensioners or the airbags could op-

erate:

In the following examples, there is a

risk that pretensioners orairbags may

not be triggered:

– side impact to the front or rear of the

vehicle;

– frontal impact, under the tail of a

lorry;

– impact under vehicle such as pave-

ment;

– rear impact, however severe;

– the vehicle overturning;

– ...

– frontal impact against an obstacle

with a sharp angle;

– potholes;

– drop or hard landing;

– stones;

– ...

1.32

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (6/6)

All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent

the risk of serious injuries caused by items which may be dislodged when it inflates.

Warnings concerning the driver’s airbag

– Do not modify the steering wheel or the steering wheel boss.

– Do not cover the steering wheel boss under any circumstances.

– Do not attach any objects (badge, logo, clock, telephone holder, etc.) to the steering wheel boss.

– The steering wheel must not be removed (except by qualified personnel from our Network).

– Do not sit too close to the steering wheel when driving: sit with your arms slightly bent (see “Adjusting your driving position”

➥ 1.23). This will allow sufficient space for the airbag to deploy correctly and be fully effective.

Warnings concerning the passenger airbag

– Do not attach or glue any objects (badge, logo, clock, telephone holder, etc.) to the dashboard on or near the airbag.

– Do not place anything between the dashboard and the passenger (pet, umbrella, walking stick, parcels, etc.).

– The passenger must not put his or her feet on the dashboard or seat as there is a risk that serious injuries may occur. In

general, parts of the body should be kept away from the dashboard (knees, hands, head, etc.).

– The devices in addition to the front passenger seat belt should be reactivated as soon as a child seat is removed, to ensure

the protection of the passenger in the event of an impact.

A REAR-FACING CHILD SEAT MUST NOT BE FITTED TO THE FRONT PASSENGER SEAT UNLESS THE

RESTRAINT SYSTEMS IN ADDITION TO THE FRONT PASSENGER SEATBELT ARE DEACTIVATED ➥ 1.57.

1.33

METHODS OF RESTRAINT IN ADDITION TO THE REAR SEAT BELTS

Depending on the vehicle, they will con-

sist of:

– Have the entire restraint

system checked following

an accident.

– side seat belt inertia reel preten-

sioners;

– No operation whatso-

ever is permitted on any part

of the system (pretensioners,

airbags, computers, wiring) and

the system components must not

be reused on any other vehicle,

even if identical.

– chest force limiters.

These systems are designed to act in-

dependently or together when the vehi-

cle is subjected to a frontal impact.

Depending on the severity of the

impact, the system can trigger:

– Only qualified personnel from our

Network may work on the airbags;

otherwise the system may trigger

accidentally and cause injury.

1

– seat belt locking;

– the seat belt inertia reel pretensioner

(which engages to correct seat belt

slack).

– The electric trigger system may

only be tested by a specially

trained technician using special

equipment.

Side seat belt pretensioners

The pretensioners hold the seat belt

against the body, holding the occupant

more securely against the seat, thus in-

creasing the seat belt’s efficiency.

Force limiter

Above a certain severity of impact, this

mechanism is used to limit the force of

the belt against the body so that it is at

an acceptable level.

– When the vehicle is scrapped,

contact an approved dealer for

disposal of the pretensioner and

airbags gas generators.

With the ignition on, following a signif-

icant frontal impact and depending on

the severity of the impact, the system

may trigger the seat belt inertia reel

pretensioner 1, which instantly retracts

the seat belt.

1.34

SIDE PROTECTION DEVICES

Side Airbag

This airbag may be fitted to each of the

front seats and is activated at the sides

of the seats (door side) to protect the

occupants in the event of a severe side

impact.

Curtain Airbag

This is an airbag fitted (depending on

the vehicle) along the upper sides of

the vehicle – they inflate along the front

and rear door side windows to protect

the passengers in the event of a severe

side impact.

Warning relating to the side airbag

– Fitting seat covers: seats equipped with an airbag require covers spe-

cifically designed for your vehicle. Contact an approved dealer to find

out if these covers are available. The use of any covers other than those

designed for your vehicle (including those designed for another vehicle) may

affect the operation of the airbag and reduce your protection.

– Do not place any accessories, objects or even pets between the seatback, the

door and the internal fittings. Do not cover the seatback with any items such as

clothes or accessories. This may prevent the air bag from operating correctly

or cause injury when the airbag is deployed.

– No work or modification whatsoever may be carried out on the seat or internal

fittings, except by qualified personnel from an approved Dealer.

– This airbag operates through slits in the front seatbacks (door side): never

insert any objects in these slits.

1.35

ADDITIONAL METHODS OF RESTRAINT

All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent

the risk of serious injuries caused by items which may be dislodged when it inflates.

The airbag is designed to complement the action of the seat belt. Both the airbag and the seat belt are integral parts

of the same protection system. It is therefore essential to wear seat belts at all times. If seat belts are not worn, the oc-

cupants are exposed to the risk of serious injury in the event of an accident. It may also increase the risk of minor su-

perficial injuries occurring when the airbag is deployed, although such minor injuries are always possible with airbags.

If the vehicle should overturn or in the event of a rear impact, however severe, the pretensioners and airbags are not always

triggered. Impacts to the underside of the vehicle, e.g. from pavements, potholes or stones, can all trigger these systems.

– No work or modification whatsoever may be carried out on any part of the airbag system (airbags, pretensioners, computer,

wiring harness, etc.), except by qualified Network personnel.

– To ensure that the system is in good working order and to avoid accidental triggering of the system which may cause injury,

only qualified Network personnel may work on the airbag system.

– As a safety precaution, have the airbag system checked if your vehicle has been involved in an accident, or is stolen or

broken into.

– When selling or lending the vehicle, inform the user of these points and hand over this handbook with the vehicle.

– When scrapping your vehicle, contact your approved Dealer for disposal of the gas generator(s).

1.36

CHILD SAFETY: General information (1/2)

Carrying children

Please ensure that you comply with the

legislation of your country.

Children, and adults, must be correctly

seated and strapped in for all journeys.

The children being carried in your vehi-

cle are your responsibility.

Driver’s responsibility

when parking or stopping

the vehicle

A child is not a miniature adult. Children

To prevent the doors being

opened, use the “Child lock”

feature. ➥ 1.18.

are at risk of specific injuries as their

muscles and bones have not yet fin-

ished growing. The seat belt alone

would not provide suitable protection.

Use an approved child seat and ensure

you use it correctly.

Never leave an animal,

child or adult who is not self-suffi-

cient alone on your vehicle, even for

a short time.

A collision at 31 mph

(50 km/ꢀh) is the same

as falling a distance of

10 metres.

They may pose a risk to themselves

or to others by starting the engine,

activating equipment such as the

electric windows or by locking the

doors.

Transporting

a

child without

a restraint is the equivalent of allow-

ing him or her to play on a fourth-

floor balcony without railings.

Special features of LPG

versions

Also, in hot and/or sunny weather,

please remember that the tempera-

ture inside the passenger compart-

ment increases very quickly.

The vehicle’s LPG installa-

tion may lead to changes to

the vehicle’s features compared to

the petrol version.

Never travel with a child held in your

arms.

RISK OF DEATH OR SERIOUS

INJURY.

In the event of an accident, you will

not be able to keep hold of the child,

even if you yourself are wearing a

seat belt.

This may relate to the number of

seats and the installation of child

seats.

If your vehicle has been involved in

a road accident, replace the child

seat and have the seat belts and

ISOFIX anchorage points checked.

Please contact an authorised dealer.

1.37

CHILD SAFETY: General information (2/2)

Before fitting a child seat, read the

Using a child seat

manual and respect its instructions. If

you experience any difficulties during

installation, contact the manufacturer

of the equipment. Keep the instructions

with the seat.

The level of protection offered by the

child seat depends on its ability to re-

strain your child and on its installation.

Incorrect installation compromises the

protection it offers the child in the event

of harsh braking or an impact.

Before purchasing a child seat, check

that it complies with the regulations for

the country you are in and that it can

be fitted in your vehicle. Consult an ap-

proved dealer to find out which seats

are recommended for your vehicle.

The regulations on transporting chil-

dren are specific to each country. The

use of a child seat during transport de-

pends on the age and/or the size and/

or weight of the child.

Never leave a child unat-

tended in the vehicle.

Check that your child is

always strapped in and that

the belt or safety harness used is

correctly set and adjusted. Avoid

wearing bulky clothing which could

cause the belts to slacken.

For children who do not need to be

transported in a child seat, make sure

that the seat belt is correctly adjusted

and fastened.

Set a good example by always fas-

tening your seat belt and teaching

your child:

– to strap themselves in correctly;

Never let your child put their head or

arms out of the window.

In all cases, you must comply with the

regulations of the particular country you

are in.

– to always get in and out of the car

at the kerb, away from busy traf-

fic.

Check that the child is in the correct

position for the entire journey, espe-

cially if asleep.

Do not use a second-hand child

seat or one without an instruction

manual.

Check that there are no objects in

the vicinity of the child seat which

could impede its operation.

1.38

CHILD SAFETY: choosing a child seat

Rear-facing child seats

Forward-facing child seats

Booster cushions

A baby’s head is, proportionally, heavier

than that of an adult and its neck is very

fragile. Transport the child in this po-

sition for as long as possible (until the

age of 2 at the very least). It supports

both the head and the neck.

Up to 18 kg or 4 years, the child may

travel on a forward-facing seat.

From 15 kg or 4 years, the child can

travel using a booster seat, which will

enable the seat belt to be adapted

to suit his/her size and shape. The

booster seat cushion must be fitted with

guides to position the seat belt on the

child’s thighs rather than the stomach.

It is recommended that you use a seat-

back fitted with a belt strap guide which

can be adjusted in terms of height to

position the seat belt in the centre of the

shoulder. It must never rest on the neck

or on the arm.

Choose your seat according the child’s

size: their head and abdomen are the

areas which must be most protected. A

forward-facing child seat which is firmly

attached to the vehicle will reduce the

risk of impact to the head. Ensure your

child travels in a forward-facing seat

with a harness for as long as their size

permits.

Choose a bucket type seat for best side

protection and change it as soon as the

child’s head is higher than the shell.

Choose a bucket type seat for optimum

side protection.

Choose a bucket type seat for optimum

side protection.

1.39

CHILD SAFETY: choosing a child seat mounting (1/3)

There are two ways of attaching child

seats: via the seat belt or using the

ISOFIX system.

Attachment via the seat belt

The seat belt must be adjusted to

ensure that it is effective in the event of

harsh braking or an impact.

Ensure that the strap paths indicated

by the child seat manufacturer are re-

spected.

Always check that the seat belt is cor-

rectly fastened by pulling it up, then

pulling it out fully whilst pressing on the

child seat.

Check that the seat is correctly held by

moving it from side to side and back

to front: the seat should remain firmly

fixed.

Check that the child seat has not been

installed at an angle and that it is not

resting against a window.

The seat belt must never

be twisted or the tension

relieved. Never pass the

shoulder strap under the

arm or behind the back.

Check that the seat belt has not

been damaged by sharp edges.

If the seat belt does not operate nor-

mally, it will not protect the child.

Consult an approved dealer. Do not

use this seat until the seat belt has

been repaired.

Do not use the child seat

if it may unfasten the seat

belt restraining it: the base

of the seat must not rest on

the buckle and/or catch of the seat

belt.

1.40

CHILD SAFETY: choosing a child seat mounting (2/3)

Attachment using the ISOFIX

system

Attach the child seat with the ISOFIX

locks, if these are provided. The ISOFIX

system allows quick, easy, safe fitting.

Approved child seats ISOFIX are stand-

ardised in accordance with current reg-

ulations if any of the four cases below

applies:

The ISOFIX system consists of 2 rings

and, in some cases, a third ring.

– ISOFIXuniversal 3-point forward-fac-

ing seat;

– ISOFIXsemi-universal 2-point seat;

– specific;

– i-Size which has either:

1

– a strap which attaches to the third

ring of the seat concerned;

– or a strut that rests on the vehi-

cle floor, compatible with the ap-

proved seat i-Size, the role of

which is to prevent the child seat

from moving in the event of a col-

lision.

The ISOFIX anchorage

points have been exclu-

sively designed for child

The two rings 1 are located between the

seats with the ISOFIX

and are identified by a

^{seatback and the seat}^{base of the seat}

symbol.

system. Never fit a different type of

child seat, seat belt or other objects

to these anchorage points.

Check that nothing is obstructing

the anchorage points.

If your vehicle has been involved in

a road accident, have the ISOFIX

anchorage points checked and re-

place your child seat.

In the latter three cases check that your

child seat can be installed by consulting

the list of compatible vehicles.

No modifications may be

made to the component

parts of the restraint system

(seat belts, ISOFIX and

seats and their mountings) originally

fitted.

Before using an ISOFIX child seat that you purchased for another vehi-

cle, check that its installation is authorised. Consult the list of vehicles

which can be fitted with the seat from the equipment manufacturer.

1.41

CHILD SAFETY: choosing a child seat mounting (3/3)

2

3

The ISOFIX anchorage

points have been exclu-

sively designed for child

3

4

seats with the ISOFIX

system. Never fit a different type of

child seat, seat belt or other objects

to these anchorage points.

4

Check that nothing is obstructing

the anchorage points.

If your vehicle has been involved in

a road accident, have the ISOFIX

anchorage points checked and re-

place your child seat.

Attachment using the ISOFIX

system (continued)

Front passenger seat

Attach the 3 hook of the upper strap 2 to

^{the ring 4 marked with the} symbol.

The third ring 4 is used to attach the

upper strap 2 on some child seats.

All seats

Rear seats

Pull the upper strap 2 so that the back

of the child seat comes into contact with

the back of the vehicle seat.

The upper strap 2 should be positioned

between the seatback and the rear

parcel shelf. To do so, remove the rear

parcel shelf ➥ 3.36.

Check that the seatback

of the forward-facing child

seat is in contact with the

back of the vehicle seat.

In this case, the child seat may not

always rest on the base of the vehi-

cle seat.

Attach the 3 hook on one of the 4 rings

^{marked with the} symbol.

1.42

CHILD SAFETY: fitting a child seat, general information (1/2)

Some seats are not suitable for fitting

child seats. The diagram on the follow-

ing page shows you how to attach a

child seat.

The types of child seat indicated may

not be available. Before using a differ-

ent child seat, check with the manufac-

turer that it can be fitted.

After installing the child seat, when this

is possible, you can move the vehi-

cle seat forward if necessary (so as to

leave enough space in the rear seats

for passengers or other child seats).

For a rear-facing child seat, do not let

it touch the dashboard or move it to the

furthest forward position.

In the front seat

The laws concerning children travel-

ling in the front passenger seat differ in

every country. Consult the legislation in

force and follow the indications on the

diagram on the following page.

Do not change other settings after in-

stalling the child seat.

Fit the child seat in a rear

seat wherever possible.

Before fitting a child seat in this seat (if

authorised):

Make sure the child seat or

the child’s feet do not pre-

vent the front seat from locking cor-

rectly. ➥ 1.21.

– lower the seat belt as far as possible;

– move the seat as far back as possi-

ble;

Check that when installing the child

seat in the vehicle it is not at risk of

coming loose from its base.

– gently tilt the seatback away from

vertical (approximately 25°);

If you have to remove the headrest,

check that it is correctly stored so

that it does not come loose under

harsh braking or impact.

– on equipped vehicles, raise the seat

base as far as possible.

Always fully raise the seat headrest so

that it does not interfere with the child

seat ➥ 1.98.

Always attach the child seat to the

vehicle even if it is not in use so that

it does not come loose under harsh

braking or impact.

RISK OF DEATH OR

SERIOUS INJURY: before

fitting a rear-facing child

seat in this seat, make sure

that the front passenger airbag has

been deactivated. ➥ 1.57.

1.43

CHILD SAFETY: fitting a child seat, general information (2/2)

In the rear side seat

Always remove the headrest from the

rear seat on which the child seat is

positioned. ➥ 3.33. If necessary, posi-

tion the rear seat as far back as pos-

sible. This must be done before fitting

the child seat. Check that the child seat

is resting against the back of the rear

seat.

Rear centre seat

A carrycot can be installed across the

vehicle and will take up at least two

seats. Position the child with his or her

feet nearest the door.

Check that the belt is suitable for secu-

ring your child seat. Consult an appro-

ved dealer.

Move the front seat as far forward as

possible to install a rear-facing child

seat, then move back the seat in front

as far as it will go, although without al-

lowing it to come into contact with the

child seat.

For the safety of the child in the for-

ward-facing position:

– move the relevant seat backwards

as far as possible;

– move the seat in front of the child

forwards, and set the position of the

seatback to avoid contact between

the seat and the child’s legs.

A child seat with floor sup-

ports must never be in-

stalled on the rear centre

seat.

RISK OF DEATH OR SERIOUS

INJURY.

When fitting a child seat

(Group 2 or 3 booster seat),

check that the seat belts

operate (wind) correctly:

➥ 1.23. If necessary, adjust the posi-

tion of the vehicle seat.

Fit the child seat in a rear

seat wherever possible.

To install an ISOFIX seat in

this seat, detach the central

seat belt by hand before engaging

the bolts.

Ensure that the child seat

or the child’s feet do not

prevent the front seat from

locking correctly. ➥ 1.21 or

➥ 3.34.

1.44

CHILD SEATS: attachment by seat belt (1/6)

Visual installation of the five-door version

³

Check the status of the airbag

before fitting a child seat or allowing a

passenger to use the seat.

Seat not suitable for fitting

child seats.

²

Child seat attached using the belt

¬

Seat which allows a child seat

with “Universal” approval to be attached

by a seat belt.

Using a child safety system

which is not approved for

this vehicle will not correctly

protect the baby or child.

RISK OF DEATH OR

SERIOUS INJURY: before

fitting a rear-facing child

seat in this seat, make sure

that the front passenger airbag has

been deactivated. ➥ 1.57.

They risk serious or even fatal injury.

1.45

CHILD SEATS: attachment by seat belt (2/6)

The table below summarises the information already shown on the diagram on the previous page, to ensure the regula-

tions in force are respected.

Five-seater version

Front passenger seat

Rear side

seats

Rear centre

seat

Type of child seat

Weight of the child

Without airbag

or with airbag

deactivated

With airbag

activated

Carrycot fitted across

the vehicle

Group 0

< 10 kg

X

U (2)

U (3)

X

Rear-facing shell seat

Groups 0 or 0 +

< 10 kg and < 13 kg

< 13 kg and 9 to 18 kg

9 to 18 kg

U (1) (5)

U (3) (6)

Shell seat/rear-facing

seat

Groups 0+ and 1

U (1) (5)

X

U (3)

U (3) (6)

Forward-facing seat

Group 1

X

U (5)

U (4)

U (4) (6)

U (4)

Booster seat

Groups 2 and 3

15 to 25 kg and 22 to

36 kg

(1) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in this seat, make sure that the front

passenger airbag has been deactivated. ➥ 1.57.

1.46

CHILD SEATS: attachment by seat belt (3/6)

X = Seat not suitable for fitting child seats of this type.

U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.

(2) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest

the door.

(3) If necessary, position the vehicle seat as far back as possible. In order to install a rear-facing child seat, move the front seat

as far forward as possible, then move the front seat back as far as it will go, without allowing it to come into contact with the

child seat.

(4) In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the

child seat. ➥ 3.33. Move the seat in front of the child forwards, move the seatback forward to avoid contact between the seat

and the child’s legs.

(5) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).

(6) RISK OF DEATH OR SERIOUS INJURY: a child seat with a floor support must never be fitted.

1.47

CHILD SEATS: attachment by seat belt (4/6)

The table below summarises the information already shown on the diagram on the previous page, to ensure the regula-

tions in force are respected.

Utility version

Front passenger seat

Type of child seat

Weight of the child

Without airbag

or with airbag

deactivated

With airbag activated

Carrycot fitted across the vehicle

Group 0

< 10 kg

X

Rear-facing shell seat

Groups 0 or 0 +

< 10 kg and < 13 kg

U (1) (5)

Shell seat/rear-facing seat

Groups 0+ and 1

< 13 kg and 9 to 18 kg

U (1) (5)

X

Forward-facing seat

Group 1

9 to 18 kg

X

U (5)

Booster seat

Groups 2 and 3

15 to 25 kg and 22 to 36 kg

(1) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in this seat, make sure that the front

passenger airbag has been deactivated. ➥ 1.57.

1.48

CHILD SEATS: attachment by seat belt (5/6)

X = Seat not suitable for fitting child seats of this type.

U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.

(5) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).

1.49

CHILD SEATS: attachment by seat belt (6/6)

Visual installation of the utility version

³

Check the status of the airbag

before fitting a child seat or allowing a

passenger to use the seat.

Seat not suitable for fitting

child seats.

²

Child seat attached using the belt

¬

Seat which allows a child seat

with “Universal” approval to be attached

by a seat belt.

Using a child safety system

which is not approved for

this vehicle will not correctly

protect the baby or child.

RISK OF DEATH OR SERIOUS

INJURY: before fitting a rear-facing

child seat in this seat, make sure

that the front passenger airbag has

been deactivated. ➥ 1.57.

They risk serious or even fatal injury.

1.50

CHILD SEATS: fitted using the ISOFIX SYSTEM (1/6)

Visual installation of the five-door version

Child seat fitted using the ISOFIX

mounting



Seat which allows an ISOFIX

child seat to be fitted.

The rear seats are fitted with

an anchorage point which allows a

forward-facing ISOFIX child seat with

universal approval to be attached. The

anchoring points are located on the

passenger seatback for the front seat

and on the bench seatback for the rear

seats.

Seat which does not allow a

child seat to be fitted.

²

Using a child safety system

which is not approved for

this vehicle will not correctly

RISK OF DEATH OR

SERIOUS INJURY:

before fitting a rear facing

child seat on the front pas-

Fit the child seat in a rear

seat wherever possible.

To install an ISOFIX seat in

this seat, detach the central

seat belt by hand before engaging

the bolts.

protect the baby or child.

They risk serious or even fatal injury.

senger seat, check that the airbag

has been deactivated ➥ 1.57.

1.51

CHILD SEATS: fitted using the ISOFIX SYSTEM (2/6)

The table below summarises the information already shown on the diagram on the previous pages, to ensure the regula-

tions in force are respected.

Front passenger seat

Weight of

the child

Seat size

ISOFIX

Rear side

seats

Rear centre

seat

Type of child seat

Without airbag

or with airbag

deactivated

With airbag

activated

Carrycot fitted across

the vehicle

Group 0

F, G

< 10 kg

X

[L1, L2]

E

Rear-facing shell seat

Groups 0 or 0 +

< 13 kg

IL (1) (4)

IL (2)

[R1]

Shell seat/rear-facing

seat

Groups 0+ and 1

C, D

< 13 kg and 9 to

18 kg

IL (1) (4)

X

IL (2)

X

[R3, R2]

A, B, B1

Forward-facing seat

Group 1

9 to 18 kg

X

IUF - IL (1)

IUF - IL (2) (3)

X

[F3, F2, F2X]

Booster seat

Groups 2 and 3

15 to 25 kg and

25 to 36 kg

[B2]

Seat i-Size

i-U (1) (4)

i-UF

i-U

X

1.52

CHILD SEATS: fitted using the ISOFIX SYSTEM (3/6)

X = Seat not suitable for fitting child seats of this type.

IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at-

tached using the ISOFIX system; check that it can be fitted.

i-U = Suitable for “universal” front-facing and rear-facing i-Size restraint devices.

i-UF = Suitable only for “universal” front-facing and rear-facing i-Size restraint devices.

(1) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).

(2) If necessary, position the vehicle seat as far back as possible. In order to install a rear-facing child seat, move the front seat

as far forward as possible, then move the front seat back as far as it will go, without allowing it to come into contact with the

child seat.

(3) In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the

child seat. ➥ 3.33. Move the seat in front of the child forwards, move the seatback forward to avoid contact between the seat

and the child’s legs.

The size of the ISOFIX child seat is indicated by a letter:

– A, B, B1 [F3, F2, F2X]: for forward-facing seats in Group 1 (9 to 18 kg);

– CandD [R3,R2]: rear-facing seats or shell seats in Group 0+ (less than 13 kg) or Group 1 (9 to 18 kg);

– E [R1]: rear-facing shell seats in group 0 (less than 10 kg) or 0+ (less than 13 kg);

– F, G [L1, L2]: carrycots in group 0 (less than 10 kg);

– [B2]: boosters in groups 2 and 3 (15 to 25 kg and 22 to 36 kg).

(4) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in this seat, make sure that the front

passenger airbag has been deactivated. ➥ 1.57.

1.53

CHILD SEATS: fitted using the ISOFIX SYSTEM (4/6)

The table below summarises the information already shown in the diagram on the following pages, to ensure the appli-

cable regulations are respected.

Utility version

Front passenger seat

Type of child seat

Weight of the child

Seat size ISOFIX

Without airbag or with

airbag deactivated

With airbag activated

Carrycot fitted across

the vehicle

Group 0

F, G

< 10 kg

< 13 kg

X

[L1, L2]

E

Rear-facing shell seat

Groups 0 or 0 +

IL (1) (4)

[R1]

C

X

Shell seat/rear-facing

seat

[R3]

< 13 kg and 9 to 18 kg

D

Groups 0+ and 1

IL (1) (4)

[R2]

A, B, B1

Forward-facing seat

Group 1

9 to 18 kg

X

IUF - IL (1)

[F3, F2, F2X]

Booster seat

Groups 2 and 3

15 to 25 kg and 25 to

36 kg

[B2]

X

IUF - IL (1)

i-UF

Seat i-Size

i-U (1) (4)

1.54

CHILD SEATS: fitted using the ISOFIX SYSTEM (5/6)

X = Seat not suitable for fitting child seats of this type.

IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at-

tached using the ISOFIX system; check that it can be fitted.

i-U = Suitable for “universal” front-facing and rear-facing i-Size restraint devices.

i-UF = Suitable only for “universal” front-facing and rear-facing i-Size restraint devices.

(1) Position the vehicle seat as far back as possible and gently tilt the seatback (approximately 25°).

The size of the ISOFIX child seat is indicated by a letter:

– A, B, B1 [F3, F2, F2X]: for forward-facing seats in Group 1 (9 to 18 kg);

– CandD [R3,R2]: rear-facing seats or shell seats in Group 0+ (less than 13 kg) or Group 1 (9 to 18 kg);

– E [R1]: rear-facing shell seats in group 0 (less than 10 kg) or 0+ (less than 13 kg);

– F, G [L1, L2]: carrycots in group 0 (less than 10 kg);

– [B2]: boosters in groups 2 and 3 (15 to 25 kg and 22 to 36 kg).

(4) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in this seat, make sure that the front

passenger airbag has been deactivated. ➥ 1.57.

1.55

CHILD SEATS: fitted using the ISOFIX SYSTEM (6/6)

Visual installation of the utility version

Child seat fitted using the ISOFIX

mounting



Seat which allows an ISOFIX

child seat to be fitted.

The rear seats are fitted with

an anchorage point which allows a

forward-facing ISOFIX child seat with

universal approval to be attached. The

anchoring points are located on the

passenger seatback for the front seat

and on the bench seatback for the rear

seats.

Seat which does not allow a

child seat to be fitted.

²

Using a child safety system

which is not approved for

this vehicle will not correctly

RISK OF DEATH OR

SERIOUS INJURY:

before fitting a rear facing

child seat on the front pas-

protect the baby or child.

They risk serious or even fatal injury.

senger seat, check that the airbag

has been deactivated ➥ 1.57

1.56

CHILD SAFETY: deactivating, activating AIRBAG front passenger (1/3)

The passenger airbag may

only be activated or deacti-

vated when the vehicle is

stationary, with the igni-

1

tion off.

2

If it is interfered with when the ve-

hicle is being driven, indicator lights

å

and © will come on.

Switch the ignition off then on again

to reset the airbag in accordance

with the lock position.

To deactivate the airbag: with the

vehicle stationary and the ignition

switched off, push and turn lock 1 to

the OFF position.

Deactivating the front

passenger airbag

Before installing a child seat on the

front passenger seat:

When the ignition is switched on, it is

essential to check that the warning

DANGER

– check that the child seat can be in-

stalled on this seat;

Since operation of the front

passenger airbag is not

compatible with the position

light

play 2.

¹

is illuminated on the dis-

– it is essential to deactivate the

airbagfor a rear-facing child seat.

of a rear-facing child seat, NEVER

fit a rear-facing child restraint

system in a seat protected by an

ACTIVATED front airbag . This can

lead to the DEATH of the CHILD or

SERIOUS INJURY.

This light remains permanently lit to

let you know that you can fit a child

seat.

1.57

CHILD SAFETY: deactivating, activating AIRBAG front passenger (2/3)

A

3

A

The markings on the dashboard and

labels A on each side of the passen-

ger sun visor 3 (example: label shown

above) remind you of these instruc-

tions.

DANGER

Since operation of the front

passenger airbag is not

compatible with the position

of a rear-facing child seat, NEVER

fit a rear-facing child restraint

system in a seat protected by an

ACTIVATED front airbag. This can

lead to the DEATH of the CHILD or

SERIOUS INJURY.

1.58

CHILD SAFETY: deactivating, activating AIRBAG front passenger (3/3)

Operating faults

It is forbidden to fit a rear-facing child

seat to the front passenger seat if the

airbag activation/deactivation system is

faulty.

Allowing any other passenger to sit in

that seat is not recommended.

1

2

Contact your approved dealer as soon

as possible.

To restart the airbag: vehicle

stopped, ignition switched off, press

and turn the lock to 1 position ON.

Activating the front

passenger airbag

You should reactivate the airbag as

soon as you remove the child seat from

the front passenger seat to ensure the

protection of the front passenger in the

event of an impact.

The passenger airbag may

only be activated or deacti-

vated when the vehicle is

stationary with the igni-

tion off.

When the ignition is switched on, you

light is off and that the

light comes on the display 2 after each

start-up for around 60 seconds.

^warning

¹

warning

must check that the

If it is interfered with when the ve-

hicle is being driven, indicator lights

The front passenger airbag has been

activated.

å

and © will come on.

Switch the ignition off then on again

to reset the airbag in accordance

with the lock position.

1.59

DRIVING POSITION: LEFT-HAND DRIVE (1/2)

7

1

2

3

4

6

8

10 11

1

9

5

24

23

21

22

14 13 12

19

20

18

17

16

15

1.60

DRIVING POSITION: LEFT-HAND DRIVE (2/2)

The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.

1 Side air vents.

2 Stalk for:

9 Controls for:

16 Handbrake.

– front seat heating;

17 “Hands-free” card holder.

18 Accessories socket.

19 Engine start/stop button.

20 Control for adjusting steering

wheel height and reach.

21 Main switch and controls for the

Cruise control/speed limiter, adap-

tive cruise control and “Lane

Centring” functions.

– direction indicator lights;

– exterior lights;

– front fog lights;

– activation/deactivation of the

Stop and Start function;

– activation/deactivation, depend-

ing on the vehicle, of the ECO or

MULTI-SENSE mode;

– hazard warning lights;

– electric door locking;

– activation/deactivation of the

parking distance control;

– activating/deactivating the 360°

camera;

– rear fog lights.

3 Instrument panel.

4 Driver airbag and horn location.

5 Controls for:

– on-board computer information

read-out and vehicle settings

customisation menu,

– remote radio and navigation

system.

22 Bonnet release control.

23 LPG control.

24 Controls for:

– ...

– lighting rheostat for control

instru- ments;

– headlight beam height remote

adjustment;

– activation/deactivation of the

steering wheel heating;

– activation/deactivation of Lane

Keeping Assist and Lane

Departure Warning.

6 Steering column stalk for wind-

screen and rear screen wash/

wiper.

7 Centre air vents.

8 Multimedia screen.

10 Heating or air conditioning con-

trols.

11 Passenger airbag location.

12 Glove compartment.

13 Charging zone/telephone storage.

14 Gearstick.

15 Controls for:

– activating/deactivating the elec-

tronic parking brake;

– activation/deactivation of the

function AUTOHOLD.

1.61

DRIVING POSITION: RIGHT-HAND DRIVE (1/2)

4 6

5

8

9

11

1

2

3

4

7

10

12

1

13

23

24

22 21

17 16

18

15

14

20

19

1.62

DRIVING POSITION: RIGHT-HAND DRIVE (2/2)

The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.

1 Side air vents.

8 Main switch and controls for the

Cruise control/speed limiter, adap-

tive cruise control and “Lane

Centring” functions.

14 LPG control.

2 Passenger airbag location.

3 Heating or air conditioning con-

trols.

15 Control for adjusting steering

wheel height and reach.

16 Engine start/stop button.

17 Gearstick.

4 Centre air vents.

9 Instrument panel.

5 Multimedia screen.

6 Controls for:

10 Driver airbag and horn location.

11 Controls for:

18 Controls for:

– activating/deactivating the elec-

tronic parking brake;

– activation/deactivation of the

function AUTOHOLD.

– front seat heating;

– activation/deactivation of the

Stop and Start function;

– activation/deactivation, depend-

ing on the vehicle, of the ECO or

MULTI-SENSE mode;

– hazard warning lights;

– electric door locking;

– activation/deactivation of the

parking distance control;

– activating/deactivating the 360°

camera;

– on-board computer information

read-out and vehicle settings

customisation menu,

– remote radio and navigation

system.

19 “Hands-free” card holder.

20 Handbrake.

21 Charging zone/telephone storage.

22 Accessories socket.

23 Glovebox.

12 Steering column stalk for wind-

screen and rear screen wash/

wiper.

13 Controls for:

24 Bonnet release control.

– lighting rheostat for control

instru- ments;

– headlight beam height remote

adjustment;

– ...

7 Stalk:

– activation/deactivation of the

steering wheel heating;

– activation/deactivation of Lane

Keeping Assist and Lane

Departure Warning.

– direction indicator lights;

– exterior lights;

– front fog lights;

– rear fog lights.

1.63

WARNING LIGHTS (1/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

C

A

B

A

B

1

Instrument panel A, B or C: it illumi-

nates when the ignition is switched on.

Press or lift the 1 switch as many times

as required to adjust the intensity.

In some cases, the appearance of a

warning light is accompanied by a mes-

sage on the instrument panel.

If no lights or sounds are ap-

parent, this indicates a fault

in the instrument panel. This

indicates that it is essential

Warning light ® re-

quires you to stop immedi-

ately, for your own safety,

as soon as traffic conditions

allow. Switch off the engine and do

not restart it. Contact an approved

Dealer.

to stop immediately (as soon as traf-

fic conditions allow). Ensure that the

vehicle is correctly immobilised and

contact an approved Dealer.

Warning light © means you

should drive very carefully to an

authorised dealer as soon as

possible. If you fail to follow this

recommendation, you risk damag-

ing your vehicle.

1.64

WARNING LIGHTS (2/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Side light warning light

Indicator light airbag

Brake circuit fault warning

light

š

á

k

g





–

˜

å

D

It lights up when the ignition or

the engine is switched on and goes off

after a few seconds.

Main beam headlight tell-

tale

It lights up when the ignition or the

engine is switched on and goes off after

a few seconds.

Dipped beam headlight tell-

tale

If it does not come on when the igni-

tion is switched on, or comes on when

the engine is running, there is a fault in

the system.

If it comes on during braking and is ac-

^{companied by the}® warning light

and a beep, it indicates that the fluid

level in the circuit is low or that there is

a braking system fault.

Front fog light tell-tale

Contact your approved Dealer as soon

as possible.

Rear fog lights tell-tale

Stop as soon as traffic conditions allow

and consult an approved dealer.

STOP light

®

Automatic main beam head-

light indicator light ➥ 1.99

This lights up when the igni-

Battery charge warning light

Ú

tion or engine is switched on and goes

out as soon as the engine is running. It

comes on with other warning lights and/

or messages, and is accompanied by

a beep.

Left-hand direction indicator

tell-tale

It lights up when the ignition or

the engine is switched on and goes off

after a few seconds.

Right-hand direction indica-

tor tell-tale light

If it comes on on the road, accompa-

^{nied by the}® warning light and a

beep, this indicates an overload or dis-

charge in the electrical circuit.

It requires you to stop immediately, for

your own safety, as soon as traffic con-

ditions allow. Switch off the engine and

do not restart it.

Stop as soon as traffic conditions allow

and contact an approved Dealer.

Contact an approved Dealer.

1.65

WARNING LIGHTS (3/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Oil pressure warning light

It lights up when the ignition or

the engine is switched on and goes off

after a few seconds.

Warning light

Handbrake “on” and elec-

tronic parking brake warn-

©

À

}

ing light ➥ 2.22 ➥ 2.23

This lights up when the igni-

tion or engine is switched on and goes

out as soon as the engine is running.

It can light up in conjunction with other

warning lights and/or messages on the

instrument panel. It means you should

drive very care- fully to an approved

Dealer as soon as possible. If you fail

to follow this recommendation, you risk

damaging your vehicle.

Gear change indicators

_{This
lights up to advise}

If it comes on on the road, accompa-

^{nied by the}® warning light and

a beep, stop immediately and cut the

ignition.

you to change to a higher gear (arrow

pointing upwards) or lower gear (arrow

pointing downwards) ➥ 2.28.

Warning light for the elec-

tronic stability program

(ESC) and traction control system

Check the oil level. If the level is normal,

the warning light is related to something

else.



Warning light

If it appears in red during driv-

It lights up when the ignition or the

engine is switched on and goes off after

a few seconds.

Call an approved Dealer.



Variable power-assisted

steering warning light

^{ing
and is accompanied by the}®

indicator light, you must, for your safety,

stop as soon as traffic conditions allow.

Switch off the engine and do not restart

it. Call an approved Dealer. If it appears

in yellow during driving and is accom-

^{panied by the}© warning light, visit

an approved dealer as soon as possi-

ble. Meanwhile, drive with care. If you

fail to follow this recommendation, you

risk damaging your vehicle.

U

There are several reasons for the warn-

ing light to appear: ➥ 2.44.

It lights up when the ignition or the

engine is switched on and goes off after

a few seconds.

Warning light for non-availa-

bility of the electronic stabil-

ity program (ESC) and traction con-

trol system



If it comes on while driving, alongside

^{the warning light}®, this means

there is a system fault.

Door status warning light

Contact an authorised dealer.

2

“AUTOHOLD” system warn-

ing ➥ 2.27



1.66

WARNING LIGHTS (4/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Anti-lock braking warning

light

Preheating warning light

(Diesel version)

Low fuel level warning light

É

L

x

It lights up orange when the ig-

nition or the engine is switched on and

goes off after a few seconds.

It lights up when the ignition or the

engine is switched on and goes off after

a few seconds.

This should come on when the igni-

tion is switched on. It indicates that the

heater plugs are in operation.

If the light becomes orange while driv-

ing and a beep sounds, fill up with fuel

as soon as possible. There is only ap-

proximately 31 miles (50 km) worth of

fuel left.

If it lights up when you are driving, it in-

dicates a fault in the anti-lock braking

system.

It goes out when preheating is com-

plete. The engine can be started.

Toxic Fume Filter System

Warning Light

Ä

Braking will then be as normal, without

the ABS. Contact an approved Dealer

as soon as possible.

Mode warning light ECO



On vehicles that are equipped, this light

comes on when the engine is started

and, depending on the vehicle, when

the ignition is switched off while the

engine is in the standby phase ➥ 2.10

then it goes out.

– If it lights up continuously, consult

your approved dealer as soon as

possible;

– If it flashes, reduce the engine speed

until the light stops flashing. Contact

your approved Dealer as soon as

possible ➥ 2.36.

It comes on when ECO mode

Particle filter system warn-

ing light ➥ 2.14 ➥ 2.16

is active ➥ 2.28.





Freewheel indicator light

➥ 2.28



Warning light for reagent

level and faults in the ex-

haust gas reduction system ➥ 1.119

Tyre pressure loss warning

➥ 2.38



1.67

WARNING LIGHTS (5/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Coolant temperature warn-

ing light

Speed limiter warning light

➥ 2.92

Assisted parking brake fault

light ➥ 2.140

Ô

Ð

Ï









This lights up blue when you switch on

the ignition or start the engine.

Cruise control warning light

➥ 2.96

Overspeed warning light

➥ 1.70

If it turns red, stop and let the engine

idle for a minute or two.

Adaptive cruise control

warning light Stop and Go

Lane departure system

warning light ➥ 2.49



➥ 2.101

The temperature should lower and the

warning light should return to a blue

colour. If not, stop the engine. Let the

engine cool down before checking the

coolant.

Lane Keeping Assist system

warning light ➥ 2.54

Engine standby warning

light ➥ 2.10





Ó

(Depending on vehicle)

_{Indicator of failure or}

Unavailability of engine

standby warning light ➥ 2.10

unavailability of active emergency

Contact an approved Dealer.

braking ➥ 2.80

Brake pedal warning light

This lights up when the brake

pedal should be depressed ➥ 2.145.

”Hands off steering wheel”

detection warning light



➥ 2.54

1.68

WARNING LIGHTS (6/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Front and rear seat belt re-

minder warning light (de-

pending on the vehicle) ➥ 1.23

ß

D

On display D

Passenger Airbag ON

➥ 1.57



¹

Passenger Airbag OFF

➥ 1.57

1.69

DISPLAYS AND INDICATORS (1/7)

Instrument panel in miles

(option to switch to km/h)

Vehicles not fitted with a multimedia

screen

– With the ignition off, press the 2

switch as many times as required to

reach the vehicle tab 5;

– press 3 or 4 repeatedly to access

“Settings”, then press 1 “OK”;

2

1

3

4

– repeat the same operation to access

“DASHBOARD”, then “Units”.

5

Vehicles fitted with a multimedia

screen.

Engine oil level low warning

When the engine is started, the instru-

ment panel display alerts you if the min-

imum oil level is reached. ➥ 4.4.

Please see the multimedia instructions

for information on how to select the unit.

Note: in both cases, once the battery

is switched off, the on-board computer

automatically returns to the original unit

of measurement.

The first time the warning appears, it

can be cleared by pressing 1 "OK ".

Subsequent warnings will disappear

automatically after around 30 seconds.

To return to the previous mode, repeat

the same operation.

Please refer to the multimedia instruc-

tions for more information.

1.70

DISPLAYS AND INDICATORS (2/7)

7

6

A

12

8

9

11

10

Rev counter 7

(graduations x 1000)

This is displayed differently according

to how the instrument panel is custom-

ised. Depending on the style selected,

it may not be displayed.

Total mileage recorder 9 ➥ 1.81

Trip computer 10 ➥ 1.77

Instrument panel A

It lights up when the ignition is switched

on. In some cases, the appearance of a

warning light is accompanied by a mes-

sage.

Depending on the vehicle, you can cus-

tomise your instrument panel with the

content and colours of your choice.

For vehicles fitted with a multimedia

screen, refer to the equipment instruc-

tions.

Estimated mileage with remaining

fuel 11

The value is displayed after driving

400 metres. ➥ 1.81.

Overspeed buzzer

Depending on the vehicle and country,

Trip computer and multimedia

information 12

Depending on the vehicle, you can dis-

play information from the multimedia

screen (the compass, telephone, navi-

gation, etc.) or information from the trip

computer.

the



warning light is displayed

and a beep sounds. This beep sounds

as soon as the vehicle is travelling at

over 75 mph (120 km/h). This warning

light remains lit for as long as the ve-

hicle is travelling at over 74 mph

(120 km/h).

For vehicles not fitted with a multimedia

screen ➥ 1.89.

Speedometer 6

Depending on the style selected, the

display varies.

Please refer to the multimedia instruc-

tions for more information.

Driving style indicator 8 ➥ 2.28

1.71

DISPLAYS AND INDICATORS (3/7)

14

13

15

Coolant temperature indicator 14

Fuel gauge 15

If the level is at the minimum, warn-

ing light integrated in the indica-

tor comes on orange, accompanied by

a beep. Fill up as soon as possible.

In normal use, indicator 14 should be

before area 13. Under “intensive” op-

erating conditions, the needle may ap-

proach this zone. This is not serious

^{unless the warning light}® comes

on accompanied by a message on the

instrument panel and a beep.

M

1.72

DISPLAYS AND INDICATORS (4/7)

17

18

1

2

19

16

3

B

20

5

6

4

Coolant temperature indicator 16

Overspeed buzzer

Depending on the vehicle and country,

the warning light is displayed

and a beep sounds. This sounds as

soon as the vehicle exceeds 74 mph

(120 km/h). The warning light remains

on as long as the vehicle speed is over

74 mph (120 km/h).

Instrument panel B

In normal use, indicator 16 should be

before area 17. Under “intensive” op-

erating conditions, the needle may ap-

proach this zone. This is not serious

^{unless the warning light}® comes

on accompanied by a message on the

instrument panel and a beep.

It lights up when the ignition is switched

on. In some cases, the appearance of a

warning light is accompanied by a mes-

sage.

Depending on the vehicle, you can cus-

tomise your instrument panel with the

content and colours of your choice.

For vehicles fitted with a multimedia

screen, refer to the equipment instruc-

tions.



Speedometer 18

Rev counter 19

(graduations x 1000)

This is displayed differently according

to how the instrument panel is custom-

ised. Depending on the style selected,

it may not be displayed.

Depending on the style selected, the

display varies.

For vehicles not fitted with a multimedia

screen ➥ 1.89.

Driving style indicator 20 ➥ 2.28.

1.73

DISPLAYS AND INDICATORS (5/7)

25

21

24

23

22

Multimedia information 21

Fuel gauge 25

If the level is at the minimum, warn-

ing light integrated in the indica-

tor comes on orange, accompanied by

a beep. Fill up as soon as possible.

Depending on the vehicle, you can dis-

play information from the multimedia

screen (the compass, telephone, navi-

gation, etc.).

Please refer to the multimedia instruc-

tions for more information.

M

Estimated mileage with remaining

fuel 22

The value is displayed after driving

400 metres. ➥ 1.81.

Total mileage recorder 23 ➥ 1.81

Trip computer 24 ➥ 1.77

1.74

DISPLAYS AND INDICATORS (6/7)

26

C

29

28

30

31

27

Rev counter 26

(graduations x 1000)

Trip computer 29

➥ 1.77

Instrument panel C

It lights up when the ignition is switched

on. In some cases, the appearance of a

warning light is accompanied by a mes-

sage.

Coolant temperature indicator 28

Estimated mileage with remaining

fuel 30

The value is displayed after driving

400 metres.

In normal use, the indicator 28 should

be before the red zone 27. Under “in-

tensive” operating conditions, the

needle may approach this zone. This

is not serious unless the warning light

® comes on accompanied by a

message on the instrument panel and

a beep.

Depending on the vehicle, you can cus-

tomise your instrument panel with col-

ours of your choice.

➥ 1.81

Total mileage recorder 31

➥ 1.81

For vehicles fitted with a multimedia

screen, refer to the equipment instruc-

tions.

For vehicles not fitted with a multimedia

screen ➥ 1.89.

1.75

DISPLAYS AND INDICATORS (7/7)

Fuel gauge 34

32

33

If the level is at the minimum, warn-

ing light

M

integrated in the indica-

tor comes on orange, accompanied by

a beep. Fill up as soon as possible.

34

Speedometer 33

Driving style indicator 32 ➥ 2.28

Overspeed buzzer

Depending on the vehicle and country,

the



warning light is displayed

and a beep sounds. This sounds as

soon as the vehicle exceeds 74 mph

(120 km/h). The warning light remains

on as long as the vehicle speed is over

74 mph (120 km/h).

1.76

TRIP COMPUTER: general information (1/4)

1

A

B

C

1

2

1

2

3

1

4

2

3

4

3

4

Trip computer A, B or C

Depending on the vehicle, this includes

the following functions:

– distance travelled;

– journey settings;

– information messages;

– operating fault messages (con-

^{nected to the}© warning light);

– warning messages (connected to the

® warning light);

– vehicle settings customisation menu

➥ 1.89.

All these functions are described on the

following pages.

1.77

TRIP COMPUTER: general information (2/4)

A

6

5

A

1

2

3

4

7

Vehicle fitted with trip computer A

The functions will be distributed in

zones 5, 6 and 7. The location of the

zones differs depending on the style

selected.

The 7 area is dedicated to driving aids

and cannot be customised.

Press the 1 switch to browse between

areas 5 and 6, then select the functions

by pressing the 2 or 3 switches repeat-

edly.

1.78

TRIP COMPUTER: general information (3/4)

1

5

6

B

C

1

2

3

1

4

2

4

3

7

Vehicle fitted with trip computer B

Vehicle fitted with trip computer C

The functions will be distributed in

zones 5, 6 and 7.

Press the 1 switch as many times as re-

quired to reach the “Vehicle” tab.

Press the 1 switch to browse between

the zones and select the functions by

repeatedly pressing the 2 or 3 switches.

Repeatedly press the 2 or 3 switches.

1.79

TRIP COMPUTER: general information (4/4)

Selections

Interpreting some of the

values displayed after

resetting

(the display depends on the vehicle

equipment and country)

a) Trip log, operating faults and infor-

mation message readout;

The values showing average fuel con-

sumption, range and average speed

will become more stable and reliable

the further you travel after pressing the

reset button.

b) Journey settings:

– average fuel consumption;

– current fuel consumption;

– estimated range with remaining fuel;

– distance travelled;

For the first few miles after pressing the

reset key you will notice that the range

increases as you travel. This range

takes into account the average fuel con-

sumption since the last time the reset

button was pressed. However, average

consumption can decrease when:

– average speed;

4

– LPG average fuel consumption;

Resetting the trip mileage

recorder and journey

parameters (reset button)

With one of the trip parameters se-

lected as the display, press and hold

the 4 switch “OK” until the display

resets to zero.

– estimated range with remaining LPG

fuel;

– the vehicle stops accelerating;

– the engine reaches its operating

temperature (if the engine was cold

when the reset key was pressed);

– LPG range;

c) trip mileage recorder and average

speed;

– when driving from an urban area

onto the open road.

d) Reset the tyre pressure;

e) set the time;

f) distance before service;

– distance before service;

– mileage before oil change.

Automatic resetting of the

journey parameters

Resetting occurs automatically when

the maximum value of any of the pa-

rameters is exceeded.

g) Estimated range with remaining rea-

gent.

1.80

TRIP COMPUTER: journey parameters (1/5)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections

Interpreting the display selected

a) Trip log.

Successive display:

– information messages (passenger airbag OFF etc.);

– operating fault messages (“Check injection”, etc.).

Vehicle Systems OK

b) Current fuel consumption.

This value is displayed after a speed of approximately 20 mph (30 km/h) is

reached.

7.4 L/100

5.8 L/100

Average fuel consumption since the last reset.

The value is displayed after having travelled at least 400 metres since the last

reset.

c) Trip mileage recorder: distance travelled since the last reset.

112,4 km

Average speed since the last reset.

The value is displayed after driving 400 metres.

123.4 km/h

1.81

TRIP COMPUTER: journey parameters (2/5)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections

Interpreting the display selected

Average LPG

–-.- L/100

d) Average LPG fuel consumption

Range LPG

–-- km

Estimated range with remaining LPG fuel.

Distance LPG

–-- km

Distance travelled on LPG fuel since the last reset.

e) Current speed (depending on the vehicle).

55.8 mph (90 km/h)

1.82

TRIP COMPUTER: journey parameters (3/5)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections

Interpreting the display selected

Tyre pressure init.

long press

f) Reset the tyre pressure.

➥ 2.38

g) Setting the time.

16:30

➥ 1.92

1.83

TRIP COMPUTER: journey parameters (4/5)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections

Interpreting the display selected

f) Mileage before service or oil change.

On-board computer with mileage-

before-service message

Mileage before service

Service in

With the ignition on and engine not running, access the “Mileage

before service” information. When the distance value approaches its

limit, there are several possible scenarios:

30 000 km / 12 months

– If the range is less than 930 miles (1,500 km) or one month: the

message “Service due” is displayed accompanied by the nearest

term (distance or time);

Service due in

– range equal to 0 miles (0 km) or date of service reached: the mes-

sage “Service Required” is displayed accompanied by the warning

^light©.

300 km / 24 days

The vehicle requires a service as soon as possible.

Service Required

Reset: to reset the distance before the next service, press and hold button OK for approximately 10 seconds until the display

shows the mileage before service permanently.

Note: If a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the

event of an oil change, both the distance before the next service and the next oil change should be reset.

1.84

TRIP COMPUTER: journey parameters (5/5)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections

Interpreting the display selected

f) Mileage before service or oil change.

On-board computer with distance

before next service message (cntd.)

Mileage before service

Oil change in

With the ignition on and the engine not running, access the mileage

information to display the mileage before the next oil change.

30 000 km / 24 months

Depending on the vehicle, the mileage before an oil change varies according to the driving style (frequent driving at low speed,

door-to-door journeys, extensive use at idling speed, towing a trailer, etc.). The distance remaining until the next oil change can

therefore decrease more quickly in some cases than the actual distance travelled.

Reset: to reset the distance before the next service, press and hold button OK for approximately 10 seconds until the display

shows the mileage before oil change permanently.

Note: If a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the

event of an oil change, both the distance before the next service and the next oil change should be reset.

Top Up AdBlue before 2400 km

g) Estimated range with remaining reagent.

1.85

TRIP COMPUTER AND WARNING SYSTEM: information messages

These can help in the vehicle starting phase, or give information about a selection or a driving status.

Examples of information messages are given in the following pages.

Examples of messages

“Parking Brake ON”

Interpreting the display selected

Indicates that the parking brake has been applied.

Turn the steering wheel slightly whilst pressing the vehicle start button to unlock the steer-

ing column.

“Turn Steering Wheel + START”

“Vehicle Checks in Progress”

Displayed with the ignition on when the vehicle is running self-diagnostics.

1.86

TRIP COMPUTER AND WARNING SYSTEM: operating fault messages

These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as

soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.

They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The

Examples of messages

“Clean Diesel Filter”

Interpreting the display selected

Indicates the presence of water in the diesel filter; contact an approved Dealer

as soon as possible.

“Check vehicle”

Indicates a fault in one of the pedal sensors, battery management system or oil

level sensor.

“WARNING: Check Airbag”

Indicates a fault in the restraint system in addition to the seat belts. In the event

of an accident, it is possible that they may not be triggered.

“Check Anti- Pollution System”

– Indicates a fault in the vehicle’s particle filter system.

– Indicates a fault in the emissions reduction system when it is accompanied

by the



warning light. ➥ 1.119.

1.87

TRIP COMPUTER AND WARNING SYSTEM: warning message

These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic

conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.

Some examples of warning messages are given below. Note: the messages appear on the display either individually or alter-

nately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.

Examples of messages

Interpreting the display selected

“WARNING: Engine Failure Risk”

Indicates an injection fault, the vehicle’s engine has overheated or there is a

serious engine fault.

“WARNING: Braking System”

“WARNING: Electric System”

“Puncture”

Indicates a fault in the braking system.

Indicates a fault in the vehicle battery charging circuit (alternator etc.).

Indicates that at least one wheel is punctured or severely underinflated.

Indicates a problem with the steering.

“WARNING: Steering Fault”

1.88

VEHICLE SETTINGS CUSTOMISATION MENU (1/3)

Adjusting the settings

d) “Welcome”:

1

– External welcome;

– Automatic fold-out of mirrors;

– Interior welcome;

Select a menu then the function to be

modified (the display depends on the

vehicle equipment and country):

– Courtesy light auto mode.

a) “Driving”:

Depending on the function, select:

– “ON” or “OFF” to activate or deacti-

vate,

– Indicator volume;

– Free-wheel;

– ...

or

b) “Access”:

– a duration to adjust the time the lights

are switched on (e.g. for the “Follow-

me-home lighting” function).

– Unlocking the driver’s door;

– Lock doors during driving;

– Opening/closing in hands-free

mode;

– Remote locking/Approach unlock-

ing;

Please refer to the multimedia instruc-

tions for further information.

Depending on the vehicle equipment,

this function allows you to activate/de-

activate and adjust some of the vehi-

cle’s functions.

– Distance locking sound;

– Silent mode;

– Automatic locking;

c) “Wiping and lighting”:

– Follow-me-home lighting;

– Wiping in reverse;

– Automatic front wiping;

– Wiping after washing;

Vehicles fitted with a

multimedia screen 1

Accessing the settings menu

Refer to the multimedia instructions for

information on accessing the various

settings.

For safety reasons, carry

out any adjustments when

the vehicle is not being

driven.

1.89

VEHICLE SETTINGS CUSTOMISATION MENU (2/3)

Adjusting the settings

2

d) “DRIVING ASSIST”:

– Lane departure warning sound

volume;

– Lane departure warning sensitiv-

ity;

– Lane departure warning vibration;

– Lane keeping assist sensitivity;

– Blind spot warning;

– Active braking;

– Overspeed warning;

– Distance warning.

Navigate using the 4 or 5 control to

select the function to be modified and

press 6 “OK” to confirm (display may

vary according to vehicle equipment

and country):

a) “DASHBOARD”:

– Language;

– Unit;

– Style;

– Colour.

3

6

4

5

e) “LIGHTING”:

b) “VEHICLE”:

– Rear windscreen wiping in re-

verse gear;

– Automatic windscreen wiping;

– Front/rear drip wiping function;

– Exterior welcome.

– Courtesy light auto mode;

– Automatic follow-me-home light-

ing;

– Follow-me-home lighting: XX sec-

onds.

Vehicles not fitted with a

multimedia screen

f) “ACCESS”:

c) “PARKING ASSIST”:

– Beep volume.

– Lock doors during driving;

– Opening/closing in hands-free

mode;

Accessing the settings menu on

display 2

With the vehicle stationary, press

switch 3 as many times as required to

reach the “Vehicle” tab. Press repeat-

edly on the 4 or 5 switch to access the

“Settings” menu, then confirm by press-

ing 6 “OK”.

– Unlocking the driver’s door;

– Automatic re-locking;

– Silent locking;

– Automatic opening/closing;

– Automatic deployment of door

mirrors.

g) “RESET”.

=

<

function activated

function deactivated

1.90

VEHICLE SETTINGS CUSTOMISATION MENU (3/3)

To exit the menu, press 4 or 5 to access

“BACK” and confirm by pressing 6

“OK”. It may be necessary to carry out

this operation more than once.

3

6

4

5

Once a line has been selected, press 6

“OK" to adjust the function.

If you select either “PARKING ASSIST”

then “VOLUME”, or “DASHBOARD”

then “LANGUAGE”, you will have to

make a further selection (sound volume

of the parking distance control or in-

strument panel language). In this case,

make your selection and confirm it by

pressing 6 “OK”, the selected value is

shown by a

=

in front of the line.

The vehicle settings personalisation

menu cannot be used when driv-

ing. At a speed exceeding 12 mph

(20 km/h), the instrument panel dis-

play switches automatically back to

trip computer and warning system

mode.

1.91

CLOCK AND EXTERIOR TEMPERATURE (1/2)

1

6

3

4

2

5

Vehicles fitted with a multimedia

screen

Vehicles not fitted with a multimedia

screen

Set the hour using the 3 or 4 control,

then wait for three seconds: the min-

utes will flash.

The time and exterior temperature are

Press the switch 2 as many times as re-

displayed on the multimedia screen 1.

quired to reach the “Vehicle” tab.

Set the minutes using the 3 or 4 control,

then wait for three seconds: the flash-

ing stops and the time setting is com-

plete.

Refer to the multimedia instructions.

Repeatedly press control 3 or 4 to set

the 6 clock.

Press and hold switch 5 “OK” until the

time display flashes.

1.92

CLOCK AND EXTERIOR TEMPERATURE (2/2)

External temperature

indicator

Depending on the vehicle, If the

Special note:

electrical supply is cut (battery dis-

connected, broken supply wire,

etc.), the clock will automatically

go back to the right time after a few

minutes once the system is capable

of receiving information GPS.

When the external temperature is be-

tween -3°C and +3°C, the °C symbols

flash (indicates risk of ice).

External temperature

indicator

As ice formation is related

to climatic exposure, local

air humidity and temperature, the

external temperature alone is not

sufficient to detect ice.

1.93

STEERING WHEEL, POWER-ASSISTED (1/2)

Activating the function

With the ignition on, press the 3 switch:

the switch warning light illuminates.

Deactivating the function

- Automatic:

2

The function switches off automatically

after the regulation phase of approxi-

mately 30 minutes. The 3 switch warn-

ing light remains on.

3

Note: if the function has switched off

automatically, press the switch 3 twice

to reactivate it.

1

If switch 3 is not pressed again, the

function will be reactivated the next

time the ignition is switched on.

Adjusting the steering wheel

height and depth

Lower the lever 1 and position the

Steering wheel heating

(depending on vehicle)

- Manually:

This function heats the steering

wheel 2.

To deactivate the function during the

regulation phase, press the switch 3.

The 3 switch warning light goes out.

steering wheel in the required position.

Then, raise the lever fully, beyond the

point of resistance to lock the steering

wheel.

Operating principle

When the temperature is reached, the

function regulates the temperature of

the heated areas for approximately

30 minutes and then switches off auto-

matically.

Make sure that the steering wheel is

correctly locked.

For safety reasons, only

adjust the steering wheel

when the vehicle is station-

ary.

1.94

STEERING WHEEL, POWER-ASSISTED (2/2)

Note: the power-assisted steering de-

pends on the driving mode selected in

the “MULTI-SENSE” menu (➥ 3.2).

Power-assisted steering

Never drive with an inadequately

charged battery.

Variable power-assisted steering

The variable power assisted steering

system is equipped with an electronic

control system which alters the level of

assistance to suit the vehicle speed.

Steering is made easier during parking

manoeuvres (for added comfort) while

the force needed to steer increases

progressively as the speed rises (for

enhanced safety at high speeds).

Special feature of Stop and Start

With the engine on standby, power-

assisted steering is no longer opera-

tional. In this case, it returns to its origi-

nal state when the engine is restarted

or when the speed exceeds 1 mph

(1 km/h) (hill, slope etc.).

Never leave the steering wheel on

full lock when the vehicle is station-

ary.

Never turn the steering wheel when

the vehicle battery is disconnected.

Never switch off the igni-

tion when travelling down-

hill, and avoid doing so in

normal driving (assistance

is not provided).

With the engine switched off, or if

there is a system fault, it is still pos-

sible to turn the steering wheel. The

force required will be greater.

1.95

REAR VIEW MIRRORS (1/2)

Electrical folding mirrors

Special case

When the rear view mirror has been

manually deployed or folded back, it is

possible to reset it to a usage position.

The door mirrors will fold-out automati-

cally when the vehicle is unlocked. The

door mirrors fold in when the vehicle is

locked.

To do this, press the 3 switch. A me-

chanical tapping noise can be heard

from the door mirror.

Note: you can deactivate/activate the

door mirrors folding mechanism ➥ 1.89.

1

If a tapping noise cannot be heard,

press once again on 3 switch until the

tapping noise can be heard from the

door mirror.

You can force folding by pressing the 3

switch. In this situation, the door mirrors

will remain folded until the 3 button is

pressed again, regardless of automatic

folding.

2

3

Door mirrors

Adjustment

For safety reasons, carry

out any adjustments when

the vehicle is not being

driven.

When you select the door mirror using

the 2 switch, the built-in warning light

on the switch will appear. Then use

the 1 button to adjust it to the desired

position.

Heated door mirrors

Objects observed in the

rear view mirror glass are

actually closer than they

appear. For your safety,

take this into account in order to

correctly assess the distance before

any manoeuvre.

Mirror de-icing is carried out at the

same time as rear screen de-icing.

➥ 3.6 ➥ 3.12.

1.96

REAR VIEW MIRRORS (2/2)

4

Interior rear view mirror

Its position can be adjusted.

For safety reasons, carry

out any adjustments when

the vehicle is not being

driven.

Rear view mirror with lever 4

When driving at night, to avoid being

dazzled by the headlights of the vehicle

behind, depress the little lever located

behind rear view mirror 4.

Objects observed in the

rear view mirror glass are

actually closer than they

appear. For your safety,

take this into account in order to

correctly assess the distance before

any manoeuvre.

Rear view mirror without lever 4

The rear view mirror automatically dark-

ens when you are being followed by a

vehicle using main beam headlights or

in very bright lighting.

1.97

FRONT HEADRESTS

To raise the headrest

Raise it to its highest position (tilt the

seatback backwards if necessary).

Press button 2 and lift the headrest to

release it.

A

3

1

To refit the headrest

Check that the headrest rods are

clean 3.

2

Insert the headrest rods into the holes 1

(tilt the seatback backwards if neces-

sary). Lower the headrest until it locks

and press button 2 to adjust to the de-

sired height. Check that each rod 3 on

the seatback is securely locked.

To raise the headrest

Press the 2 button and pull the headrest

upwards to the height required. Check

that the bonnet is correctly locked.

To lower the headrest

Press button 2 and guide the headrest

down to the desired height. Check that

the bonnet is correctly locked.

The headrest is important

for safety. Ensure that it is in

place and in the correct po-

sition: the top of the head-

rest should be as close as possible

to the top of the head and there must

be a minimal distance between the

head and the headrest A.

1.98

EXTERIOR LIGHTING AND SIGNALS (1/6)

Depending on the vehicle, the dipped

beam headlights come on automati-

cally after several sweeps of the wind-

screen wiper blades.

2

1

3

Side lights

Turn ring 2 until the symbol is

opposite mark 3.

Dipped beam

headlights

Manual operation

š

k

This indicator light on the instrument

panel comes on.

Turn ring 2 until the symbol is opposite

mark 3. This indicator light on the in-

strument panel comes on.

Before driving at night,

check that the electrical

equipment is operating cor-

Daytime running lights

function

Automatic operation

(depending on the vehicle)

rectly and adjust the head-

light beams (if your vehicle is not

carrying its normal load).➥ 1.106.As

a general precaution, check that

the lights are not obscured (by dirt,

mud, snow or objects being trans-

ported).

The daytime running lights come on

automatically with no action on stalk 1

when the engine is started, and they go

off once the engine is switched off.

Turn ring 2 until the AUTO symbol is op-

posite mark 3: with the engine running,

the dipped beam headlights switch on

or off automatically depending on the

brightness of the light outside, without

any action on stalk 1.

1.99

EXTERIOR LIGHTING AND SIGNALS (2/6)

During deactivation of the main beam

headlights, the dipped beam headlights

return to their original position.

The main beam headlights come on au-

tomatically if:

– exterior light is weak;

2

1

– no other vehicles or lighting are de-

tected;

– the vehicle speed is above approxi-

mately 25 mph (40 km/h).

Automatic main beam

headlights



Depending on the vehicle, this system

switches the main beam headlights on

and off automatically. It uses a camera

located behind the interior rear-view

mirror to detect vehicles that are being

followed and those coming in the oppo-

site direction.

If any of the above conditions are not

fulfilled, the system switches to dipped

beam headlights.

3

Note: make sure the windscreen is not

obscured (dirt, mud, snow, condensa-

tion etc.).

To activate automatic main beam

headlights:

Main beam headlights

With the engine running and

the dipped beam headlights lit, push

stalk 1. This indicator light on the instru-

ment panel comes on.

To return to the dipped headlight posi-

tion, pull the stalk 1 towards you again.

á

turn the ring 2 until the AUTO symbol

appears opposite the 3 mark and push

the stalk 1. The

illuminated on the instrument panel.



warning light is

The system may encounter difficul-

ties under certain conditions, inclu-

ding:

– extreme weather conditions (rain,

snow, fog, etc.);

– obstruction in front of the wind-

screen or camera;

“Raise lights during driving”

function

When the main beam headlights are

activated, the “Raise lights during driv-

ing” function improves driver visibil-

ity by automatically raising the dipped

beam headlight and the main beam

headlights.

– when a following or oncoming ve-

hicle has weak or hidden lighting;

– incorrect settings for the front

headlights;

– reflective systems;

– ...

1.100

EXTERIOR LIGHTING AND SIGNALS (3/6)

Operating faults

2

1

When the message “Check Automatic

Lighting” appears on the instrument

panel, the system is deactivated.

Consult an approved dealer.

3

Using the portable naviga-

tion system at night in the

windscreen area below the

camera may disturb the op-

eration of the “automatic main beam

headlights” system (risk of reflection

on the windscreen).

Automatic main beam

headlights (continued)



To deactivate automatic main beam

headlights:

– turn ring 2 to a position other than

AUTO;

or

– pull the stalk 1.

The “automatic main beam

headlights” system should

under no circumstances be

Warning light

strument panel.



goes out on the in-

used to replace driver atten-

Note: the main beam headlights will be

activated upon deactivation of the au-

tomatic main beam headlights function.

tion and responsibility with regard

to vehicle lighting and adapting to

light, visibility and traffic conditions.

1.101

EXTERIOR LIGHTING AND SIGNALS (4/6)

Lights-on reminder buzzer

Welcome and goodbye

function

(depending on the vehicle)

2

If the lights are on after the engine is

switched off, a warning beep sounds

when the driver’s door is opened to

warn you that the lights are still on (to

avoid battery discharge or other prob-

lems).

Once the function is activated, the day-

time running lights and the rear side

lights will light up automatically upon

detection of the card or when the vehi-

cle is unlocked.

Operating faults

They switch off automatically:

If the “Check lighting” message ap-

– approximately one minute after light-

ing up;

– when starting the engine based on

the position of the lighting stalk;

the

k

warning light flashes on the

instrument panel, this indicates a light-

ing fault.

or

Switching off the lights

Consult an authorised dealer.

– upon locking the vehicle.

The lights will go out automatically

when the engine is switched off, the

driver’s door is opened or the vehicle

is locked. In this case, the next time

the engine is started the lights will be

switched back on according to the posi-

tion of the ring 2.

Activating/deactivating the

function

To activate or deactivate the external

welcome function, please see the multi-

media instructions.

Note: if the fog lights are lit, the lights

are not switched off automatically.

Select “ON” or “OFF”.

1.102

EXTERIOR LIGHTING AND SIGNALS (5/6)

With the engine lights switched off,

2

the 2 ring in AUTO, pull the lever 1 to-

wards you: the side lights and dipped

beam headlights will switch on for ap-

1

š

and

^proximatelyk^{30 seconds along with the}

warning lights on the

instrument panel.

To increase this duration, you may pull

the stalk up to four times (total time re-

stricted to approximately two minutes).

On the instrument panel, the message

“lighting on _ _ _” followed by the re-

maining time will appear as confirma-

tion. You can then lock your vehicle.

To switch off the lights before they go

out automatically, turn ring 2 to any po-

sition, then return it to position AUTO.

“See-me-home lighting”

function

This function enables you to briefly

switch on the side lights and dipped

beam headlights (e.g. to provide light

when opening a gate).

1.103

EXTERIOR LIGHTING AND SIGNALS (6/6)

Rear fog lights

Turn centre ring 4 on the stalk

until the symbol faces mark 3, then re-

Cornering lights

2



lease it.

(depending on vehicle)

1

3

When driving in forward gear, with

the vehicle speed below approxi-

mately 25 mph (40 km/h), whenever

the dipped beam headlights are on:

under certain conditions (the steering

wheel at an angle, the indicator lights

on etc.), when turning a corner one of

the front fog lights will switch on to light

the inside of the bend.

4

Operation of the fog lights depends on

the exterior lighting selected, and an in-

dicator light will light up on the instru-

ment panel.

Do not forget to switch off the fog lights

when they are no longer needed, to

avoid inconveniencing other road

users.

When reverse gear is engaged and

the dipped beam headlights are on the

two front fog lights illuminate automati-

cally.

Switching off the lights

Front fog lights

Turn centre ring 4 on the

stalk 1 until the symbol faces mark 3,

then release it.

Note: when shifting from reverse gear

into forward gear (for example during a

parking manoeuvre), the two fog lights

are activated until the vehicle exceeds

approximately 6 mph (10 km/h).

Turn the centre ring 4 again until mark 3

is opposite the symbol for the fog lights

that you wish to switch off. The corre-

sponding indicator light on the instru-

ment panel goes out.

g

Operation of the fog lights depends on

the exterior lighting position selected,

and an indicator light will light up on the

instrument panel.

The front and rear fog lights switch off

when the exterior lights are switched

off.

When driving in fog or snow, or when transporting objects which are higher than the roof, the headlights do not come on au-

tomatically.

Switching on the fog lights remains the responsibility of the driver: the indicator lights on the instrument panel inform you

whether the fog lights are lit (indicator light on) or not (indicator light not on).

1.104

AUDIBLE AND VISUAL SIGNALS

Direction indicators

Move the stalk 1 in the same direc-

tion as you want to move the steering

wheel.

2

One-touch mode

1

Briefly shift the stalk 1 upwards or

downwards, not exceeding the point

of resistance, then release it: the stalk

will return to its original position and the

direction indicator light concerned will

flash three times.

A

2

Horn

Hazard warning lights

Pressing switch 2 illuminates

all four direction indicators and the

side-mounted indicator lights simulta-

neously.

é

Press the steering wheel boss A to ac-

tivate the horn.

Headlight flasher

Pull stalk 1 towards you then release it

to flash the headlights.

It must only be used in an emergency to

warn drivers of other vehicles that you

have had to stop in an area where stop-

ping is prohibited or unexpected, or that

you are obliged to drive under special

conditions.

1.105

HEADLIGHT BEAM ADJUSTMENT

Examples of positions for

adjusting

control A according to the load

A

Driver alone or with front passenger

0

2

All seats occupied

Switch A is used to adjust the height of

the headlight beams according to the

load.

Driver with passengers and luggage

(or load) reaching the maximum

permissible all-up weight

3

4

With the dipped beam headlights lit,

press or lift switch A as many times

as is necessary to select the required

position on the instrument panel. The

position selected is displayed on the

instrument panel for approximately

30 seconds.

Driver without passengers and luggage

(or load) reaching the maximum

permissible all-up weight

Note: depending on the vehicle, at

each engine start-up the selected po-

sition may be displayed on the instru-

ment panel for approximately 30 sec-

onds.

The table below gives some examples. In all cases, adjust control A accord-

ing to the vehicle load so that the road can be seen and other drivers are not

dazzled.

1.106

WINDSCREEN WASH, WIPE (1/5)

2

A

1

B

C

D

E

Special note

Vehicle fitted with intermittent

windscreen wipers

When driving the vehicle, the wiping

speed slows down whenever the ve-

hicle stops. For example, fast wiping

speed will slow to normal wiping speed.

As soon as the vehicle moves off,

wiping will return to the speed originally

selected.

A single sweep

A short push will trigger one sweep

of the wipers.

B stop

C intermittent wiping

The wipers will pause for several

seconds between sweeps. It is

possible to change the time be-

tween sweeps by turning ring 2.

D slow continuous wiping

E fast continuous wiping

If stalk 1 is operated, it overrides and

cancels the automatic function.

1.107

WINDSCREEN WASH, WIPE (2/5)

When activating automatic wiping

or when increasing sensitivity, one

sweep of the blades is performed.

A

Note:

F

1

2

– the rain sensor is only intended as a

driving aid. In the event of reduced

visibility, the driver should manually

activate the wipers. In foggy weather

or during snowfalls, wiping is not au-

tomatically triggered and remains

under the driver’s control;

B

C

D

E

G

– in the event of temperatures below

zero, automatic wiping is not acti-

vated when the vehicle is started. It

is automatically activated as soon as

the vehicle exceeds a certain speed

(approximately 5 mph (8 km/h));

C automatic wiper function

When this position is selected, the

system detects water on the wind-

screen and triggers the wipers at a

suitable wiping speed. It is possi-

ble to change the triggering thresh-

old and the time sweeps by turning

ring 2:

Vehicle fitted with front

windscreen wiper rain sensor

The rain sensor is located on the winds-

creen, in front of the interior rear-view

mirror.

– do not activate automatic wiping in

dry weather;

– fully de-ice the windscreen before

activating automatic wiping.

A single sweep

A short push will trigger one sweep

of the wipers.

–

F: minimum sensitivity

G: maximum sensitivity

The higher the sensitivity, the

quicker the wipers will react and

the faster the wipe.

B stop

1.108

WINDSCREEN WASH, WIPE (3/5)

Operating faults

Special note

In the event of a malfunction of the au-

tomatic wiping, the wiper is set to inter-

mittent wiping. Contact an authorised

dealer.

When driving the vehicle, the wiping

speed slows down whenever the vehi-

cle stops. For example, fast wiping

speed will slow to normal wiping speed.

As soon as the vehicle moves off,

wiping will return to the speed originally

selected.

G

A

1

The operation of the rain sensor can be

disturbed in the event of:

B

– damaged windscreen wipers; a

film of water or traces left by a

blade in the sensor’s detection

zone may increase the response

time of the automatic wiper, or in-

crease the wiping frequency;

C

If stalk 1 is operated, it overrides and

cancels the automatic function.

D

Precautions

E

– In the event of ice, check whether the

blades are stuck to the windscreen

before operating the wiping mecha-

nism. If you activate the wipers while

the blades are stuck down with ice,

you may risk damaging both the

blade and the wiper motor.

– a windscreen with any chip or

crack level with the sensor, or a

windscreen covered in dust, dirt,

insects, ice, the use of washing

wax and water-repellent chemi-

cals; the windscreen wiper will

be less sensitive or may even not

react at all.

D slow continuous wiping

E fast continuous wiping

– Do not activate the wipers on a dry

screen. This will lead to premature

wear or damage to the blades.

1.109

WINDSCREEN WASH, WIPE (4/5)

Specific front wiper position

(service position)

This position enables the blades to be

lifted to remove them from the winds-

creen.

G

A

1

B

C

It may be useful to:

– to clean the blades;

– to release the blades from the winds-

creen in winter;

– replace the blades ➥ 5.33.

D

E

With the ignition on or the engine run-

ning, lift the 1 stalk twice to position A

(single sweep). The blades stop slightly

away from the bonnet.

To return the blades to low position,

with the ignition on, ensure that the

wipers have folded down onto the wind-

screen, then move the stalk 1 to posi-

tion A (single sweep).

In the event of obstacles on the

windscreen (dirt, snow, ice etc.),

clean the windscreen (including the

central area located behind the inte-

rior rear view mirror) before starting

the wipers (risk of motor overheat-

ing).

Before switching on the ignition,

place the wipers on the windscreen.

Otherwise, there may a risk of damage

to the bonnet or the wipers when they

are switched on.

Before carrying out any

action involving the wind-

screen (washing the vehi-

cle, de-icing, cleaning the

If an object is preventing a blade

from moving, it may stop functio-

ning. Remove the obstacle and

reactivate the wiper using the wiper

stalk.

windscreen etc.) return the 1 stalk

to position B (stop).

Risk of injury and/or damage.

1.110

WINDSCREEN WASH, WIPE (5/5)

Note:

In temperatures below zero, the washer

liquid risks freezing to the windscreen,

thereby reducing visibility. Heat the

windscreen using the demister control

before cleaning.

1

G

Efficiency of a wiper blade

Check the condition of the wiper

blades. How long they last depends

on you:

– it must remain clean: clean the

blade and the screen regularly

with soapy water;

– do not use it when the screen is

dry;

– free it from the screen when it has

not been used for a long time.

Windscreen washer

With the ignition on, pull stalk 1 then

release.

In all cases, replace it as soon as

it begins to lose efficiency: approxi-

mately once a year. ➥ 5.33.

A longer pull will trigger, in addition to

the windscreen washer, two sweeps

of the wipers followed, a few seconds

later, by a third.

Precaution for using the

wipers

– In freezing or snowy weather

conditions, clear the screen

before starting the wipers (risk of

motor overheating);

On vehicles fitted with a multimedia

screen, you can choose to activate or

disable the third sweep of the blades.

➥ 1.89.

When working in the engine

compartment, ensure that

the windscreen wiper stalk

is in position B (park).

– ensure that no objects are ob-

structing the travel of the blade.

Risk of injury.

1.111

REAR SCREEN WASHER, WIPER (1/2)

To stop the operation, pivot ring 3 again.

Note

3

2

When washing using a roller type car

wash, return the ring 3 on the stalk 1

to the stop position to deactivate auto-

matic wiping.

1

Efficiency of a wiper blade

Follow usage recommendations.

Check the condition of the wiper

blades. How long they last depends

on you:

– it must remain clean: clean the

blade and the screen regularly

with soapy water;

– do not use it when the screen is

dry;

– free it from the screen when it has

not been used for a long time.

Rear screen wiper

With the ignition on, rotate the

Y

ring 3 on the lever 1 until the symbol is

opposite the reference point 2.

In all cases, replace it as soon as

it begins to lose efficiency: approxi-

mately once a year. ➥ 5.33.

– stopping

Do not use the wiper arm to open or

close the tailgate.

– intermittent wiping

The wipers will pause for several

seconds between sweeps. Wiping

frequency varies with vehicle

speed;

Precaution for using the

wipers

– In freezing or snowy weather

conditions, clear the screen

before starting the wipers (risk of

motor overheating);

Before any action involving

the rear screen (washing

the vehicle, de-icing, clean-

ing, etc.) return stalk 1 to

the stop position.

– slow continuous wiping

– ensure that no objects are ob-

structing the travel of the blade.

Risk of injury and/or damage.

1.112

REAR SCREEN WASHER, WIPER (2/2)

Activation/deactivation of the rear

screen wiper

In the event of obstacles present on the

rear window (dirt, snow, etc.), the wiper

will try to sweep away all the obstacles.

If an obstacle prevents the blade from

moving, it can be stopped. Remove the

obstacle, wait for around 30 seconds

and reactivate the wiper using the wiper

stalk.

Engaging reverse gear triggers inter-

mittent wiping (if the front wipers are in

operation). If your vehicle is equipped

with a vehicle settings customisation

menu, you can opt to activate or deacti-

vate this function. ➥ 1.89.

1

For vehicles not fitted with a settings

customisation menu, you can have this

function deactivated by an authorised

dealer.

Precautions

– In the event of ice, check that the

blades are not stuck to the wind-

screen before operating the wipers.

If you activate the wiper while the

blade is blocked by ice, you risk dam-

aging both the blade and the wiping

motor.

Rear screen wash/wipe

With the ignition on, push and

hold stalk 1, then release.

p

– Do not operate the wipers on a dry

screen. This will lead to the prema-

ture wear or damage to the blades.

Holding the stalk for longer will trigger

(in addition to the windscreen washer)

two sweeps of the wipers followed,

a few seconds later, by a third (drip

wiping function).

When the stalk is released, it returns to

the rear wipe position.

1.113

FUEL TANK (1/5)

Fuel grade

Use a high-grade fuel that complies

with the legislation in force in each

country and which must comply with

the specifications given on the label on

the cover 1. ➥ 6.6.

1

3

A

2

Fuel types that conform to European

standards with which the engines of

vehicles sold in Europe are compat-

ible: refer to the table ➥ 6.6.

Useable tank capacity:

– Approximately 9.24 gallons

(42 litres) for petrol versions;

– Approximately 8.58 gallons

(39 litres) for diesel versions.

With the vehicle unlocked, to open

cover 1, press area A then release. The

cover 1 opens slightly.

Use the cap holder 2 on the flap 1

during filling to hold the cap 3 in place.

For details on filling the fuel tank, refer

to the information on “Filling up with

fuel”.

To close it, press on the fuel filler flap by

hand, as far as it will go.

Do not mix even small

amounts of petrol (un-

leaded or E85) with diesel.

Do not use ethanol-based

fuel if your vehicle is not compatible

with this fuel.

Filler cap: this is specific.

If you have to replace it,

make sure it is identical to

the original cap. Contact an

approved Dealer.

Never place the cap near a source

of heat or flame.

Do not add reagent to the fuel – oth-

erwise you risk damaging the engine

➥ 0.8. If you wish to add an additive

to the fuel, use a product approved

by our Technical Department.

Do not wash the filler area with a

high-pressure washer.

Consult an approved dealer.

1.114

FUEL TANK (2/5)

If it is not possible to add at least

1.10 gallons (5 litres) of fuel due to the

fuel level in the tank, drive the vehicle

until the tank has capacity.

Filling with fuel

With the ignition off, insert the nozzle

and insert it fully before turning it on to

fill the fuel tank (risk of splashing). Keep

the nozzle in this position throughout

the entire filling operation.

1

Petrol versions

Using leaded petrol will damage the

antipollution system and may lead to a

loss of warranty.

When the pump cuts out automatically

at the end of the filling procedure, a

maximum of two further filling attempts

may be made, as there must be suffi-

cient space in the fuel tank to allow for

expansion. Make sure that no water

enters the fuel tank during filling. The

cover 1 and its surround must remain

clean.

To ensure that the tank is not filled

with leaded petrol, the fuel tank filler

neck consists of a restrictor fitted with

a safety system which only allows

a nozzle for unleaded petrol to be

used (at the pump).

Diesel version

Special case

It is essential to use diesel fuel that

conforms with the information given on

the label inside cover 1.

When the vehicle has been stopped for

around three months, you must add

fuel to prevent damage to the fuel

pump. To do this, with the ignition off,

top-up at least 1.10 gallons (5 litres)

then start the engine to operate the

pump and renew the fuel in the circuit.

Petrol version

It is essential to use unleaded petrol.

The octane rating (RON) must comply

with the information given on the label

on the cover 1. ➥ 6.6.

To fill up with fuel, the engine

must be stopped (and not

only on standby in the case

of vehicles equipped with

the STOP and START function): you

must switch off the ignition ➥ 2.4,

➥ 2.6.

Fire hazard.

After filling, check that the cap and

cover are closed.

1.115

FUEL TANK (3/5)

Vehicles with card

No modifications what-

soever are permitted on

any part of the fuel supply

With the card in the passenger com-

partment, press the start button 4 with-

out pressing any of the pedals. Wait a

few minutes before starting.

4

system (electronic units,

wiring, fuel circuit, injectors, pro-

tective covers, etc.) as this may be

dangerous (unless undertaken by

qualified Network personnel).

This will enable the fuel circuit to be

primed. If the engine does not start,

repeat the procedure.

If the engine does not start after several

attempts, please contact an authorised

dealer.

Running out of fuel on diesel

versions

Persistent fuel odour

If you notice a persistent

fuel odour you should:

Vehicles with key/remote control

– stop the vehicle as soon as traf-

fic conditions allow and switch off

the ignition;

– Set the ignition key to “On” position

M ➥ 2.3 and wait a few minutes

before starting to enable the fuel cir-

cuit to be primed;

– switch on the hazard warning

lights and ask your passengers to

leave the vehicle and stay clear

of the traffic;

– turn the key to position D. If the

engine does not start, repeat the pro-

cedure;

– contact an approved Dealer.

– if the engine does not start after sev-

eral attempts, please contact an au-

thorised dealer.

1.116

FUEL TANK (4/5)

Useable capacity of the LPG tank: ap-

proximately 7.04 gallons (32 litres).

5

Filling up with LPG

Apply the parking brake, stop the

engine, switch off the ignition and

switch off the lights.

Always respect the safety instructions

given at filling stations.

5

Depending on the country, before refill-

ing you must screw the filling adapter 5

onto the LPG filler end piece.

It is always advisable to completely fill

the tank.

When the pump stops delivering LPG,

or when the pump flow reduces signif-

icantly, the maximum LPG level has

been reached.

At this point, do not attempt to carry on

filling.

Filling stations without self-

service

If the service station personnel carry

out the LPG filling procedure, you must

give them the adapter 5.

IMPORTANT: LPG filling

adapter 5

Depending on the country, the use

of a specific adapter is required for

LPG filling.

The filling adapter 5 is provided in

a pouch in the glove box. It may or

may not be present in the vehicle,

depending in which country the ve-

hicle was sold.

Before driving the vehicle to another

country, it is essential to consult an

approved dealer to find out the type

of adapter to use if necessary.

If you exceed the LPG tank capacity when topping-up, please go to an

accredited garage or an authorised dealer to check the automatic filler

device.

1.117

FUEL TANK (5/5)

6

Depending on the type of station, it may

be necessary to perform press and hold

the station button before filling will start.

When the pump stops supplying LPG,

or when the pump flow reduces sig-

nificantly, the maximum tank level has

been reached.

The filling will stop as soon as you re-

lease the button. Release the stop

lever (a small amount of gas may be re-

leased), lift the pistol and place it on the

distributor.

7

Replace the cap 6 to avoid any water

or foreign bodies from entering the

system.

Filling stations with self-

service

We recommend that you wear gloves

when handling the LPG pistol.

Open the tank flap of your vehicle and

unscrew the cap 6 from the end piece

of the LPG filler 7.

Carefully follow the instructions shown

on LPG distributors. These explain how

to fill up properly.

1.118

REAGENT TANK (1/4)

Please ensure that you comply with the

legislation of your country. It is impor-

tant to remember that failure to respect

regulations in force could lead to legal

action being taken against the vehicle

owner.

To fill up with reagent, the engine

must be stopped (and not on

standby in the case of vehicles

equipped with the STOP and Start

function). You must switch off the ig-

nition ➥ 2.4 ➥ 2.6.

1

A

Operating principle

The reagent is intended for diesel en-

gines fitted with the SCR (selective cat-

alytic reduction) system.

Using a reagent reduces the quantity of

nitrogen oxides in exhaust gases.

Reagent consumption in real time de-

pends on vehicle usage conditions, the

equipment fitted, and driving style.

If the “XXX MILES (XXX

KM) failure Top up AdBlue”

warning message appears,

fill the reagent tank and

refer to the filling instructions.

Filling

Useable capacity of the tank: 2.42

gal (11 litres) approximately.

Reagent quality

Risk of immobilisation of the ve-

hicle.

Use only reagents which conform

to standard ISO 22241 and in accor-

dance with the mark on the tank filler

cap.

With the ignition switched off, open the

cover A, then unscrew the cap 1.

Note: ammonium hydroxide vapour

may escape from the cap opening

when the tank temperature is high.

Fuel filler cap: this is a

specific type.

If you have to replace it,

make sure it is identical

to the original cap. Contact an ap-

proved Dealer. Do not wash the filler

area with a high pressure washer.

The reagent must not come into contact with eyes or skin. If it does, wash

the affected area with plenty of cold water. If necessary, consult a doctor.

1.119

REAGENT TANK (2/4)

Filling (continued)

The tank can be filled at the pump. With

the ignition off, insert the nozzle fully

before activating it to fill the fuel tank

(risk of splashing). Keep the nozzle in

this position throughout the entire filling

operation.

If the reagent overflows, or contami-

nates any paintwork, clean the affected

area quickly with plenty of cold water

and a soft cloth.

Note: if the reagent crystallises, use a

soft sponge.

After filling the reagent tank, check

that the cap and cover are closed,

start the engine and WAIT 10 sec-

onds with the vehicle stationary,

engine running before setting off

again.

If this operation is not carried out,

the filling of the tank will not be

taken into account automatically

until after several dozens of minutes

of driving.

The message “--- Top up AdBlue”

and/or the warning lights will con-

tinue to appear until the filling has

been taken into account by the

system.

In extreme cold weather conditions

When the pump cuts out automatically

at the end of the filling procedure, a

maximum of two further filling attempts

may be made, as there must be suffi-

cient space in the fuel tank to allow for

expansion.

In frosty weather conditions, the rea-

gent tank should be refilled when the



indicator and the message “TOP

UP AdBlue before 1200 km” appear on

the instrument panel.

Special cases

In other filling cases, it is essential to

read the information shown on the rea-

gent container (e.g. the can or bottle).

The reagent fluid freezes below about

-10°C.

In these conditions, do not attempt filling

when the fluid is frozen. In the event of

needing to top up or fill the tank with re-

Precautions for use

When filling:

– handle the reagent with care. They

can damage clothes, shoes, body-

work components etc.;

agent (on), park the vehicle in a

hotter location if possible so that the re-

agent becomes liquid again. Otherwise,

have a qualified professional top up or

fill up with reagent fluid.

– make sure that no water enters the

fuel tank.

No work whatsoever is

permitted on any part of

the system. To prevent

damage, only qualified per-

sonnel from our network may work

on the system.

1.120

REAGENT TANK (3/4)

Maintenance/Range

The information displayed on the instrument panel may be accompanied by a beep.

Indicator

Message

lights

What to do?

When the message is displayed when the ignition is switched

on, you have less than 1,488 miles (2,400 km) range.

Plan to refill, or have an Approved Dealer refill the reagent in

the tank.

–

“Top Up AdBlue before 2400 km”

“TOP UP AdBlue before 1200 km”

When the message is displayed when the ignition is switched

on, you have between 744 miles (1,200 km) and 496 miles

(800 km) range.

Plan to refill, or have an Approved Dealer refill the reagent in

the tank.



comes on.

The message is displayed when the ignition is switched on and

is repeated:

– Approximately every 62 miles (100 km), you have between

about 496 miles (800 km) and 124 miles (200 km) range;

– Approximately every 31 miles (50 km), you have less than

124 miles (200 km) range.

In any event, fill or have an Approved Dealer fill the reagent

tank as soon as possible.

“XXX KM failure Top up AdBlue”



comes on.

The engine will not start.

“0 KM failure Top up AdBlue”

flashes.

To restart, you must fill the reagent tank yourself.

1.121

REAGENT TANK (4/4)

System faults

When the indicator lights light up, this may be accompanied by a beep.

Indicator lights

Message

Readings

“Check Anti- Pollution System”

“AdBlue quality to check”

and © come on.

“AdBlue injection to check”

Indicates a fault in the system. Contact your approved

Dealer as soon as possible.



Indicates a system fault and that in less than 496

miles (800 km) it will become impossible to re-

start the vehicle.

These warnings are repeated:

– every 62 miles (100 km) until there is between

500 miles (800 km) and 124 miles (200 km) left

before the vehicle cannot be restarted;

– Every 31 miles (50 km) when there is less than

124 miles (200 km) left before the vehicle cannot

be restarted.

“XXX KM failure antipollution”



and © come on.

Contact your approved dealer as soon as possible.

Indicates that after the ignition is switched off the ve-

hicle will not restart. Call an approved Dealer.

“0 KM failure antipollution”



and © come on.

1.122

Getting to know your vehicle for Your Renault Clio 4 Door Fifth Generation (2019-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals