Get Practical advice Guide for Renault Megane SUV Third Generation (2009-2016)

Section 5: Practical advice

Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tyre inflation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tool kit (jack - wheelbrace, etc.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wheel trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Changing a wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tyres (tyre and wheel safety, use in winter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2

5.3

5.6

5.7

5.9

Headlights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.12

Rear lights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.15

Indicator lights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.20

Interior lights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.21

Fuses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.23

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.25

RENAULT card: battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.27

Fitting a radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.28

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.29

Wiper (replacing blades) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.30

Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.31

Operating faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.33

5.1

Puncture, emergency sPare wheel

special note:

In the event of a puncture,

depending on the vehicle,

you will have:

An emergency spare wheel or tyre in-

flation kit (refer to the information on the

following pages).

The Tyre Pressure Monitor function

does not check the emergency spare

wheel (the wheel replaced by the emer-

gency spare wheel disappears from the

instrument panel display).

Refer to the information on the “Tyre

pressure monitor” in Section 2.

1

emergency spare wheel

This is located in the luggage compart-

ment. To access it:

– open the tailgate;

– depending on the vehicle, unscrew

the anchorage points;

– fold back the luggage compartment

carpet using tab 1;

– unscrew the central mounting;

– remove the emergency spare wheel.

If the emergency spare wheel has been stored for several years, have it checked by your Dealer to ensure that it is

safe to use.

Vehicles fitted with an emergency spare wheel smaller than the four other wheels:

– Never fit more than one emergency spare wheel to the same vehicle.

– Replace the emergency spare wheel as soon as possible with a wheel with the same dimensions as the original.

– When this is fitted to the vehicle, which must only be a temporary measure, the driving speed must not exceed the speed

indicated on the label on the wheel.

– Fitting an emergency spare wheel may alter the way the vehicle usually runs. Avoid sudden acceleration or deceleration and

reduce your speed when cornering.

– If you need to use snow chains, fit the emergency spare wheel to the rear axle and check the tyre pressure.

5.2

tyre Pressure KIt (1/3)

Do not attempt to use the

inflation kit if the tyre has

been damaged as a result

of driving with a puncture.

The kit is only approved for

inflating the tyres of the ve-

hicle originally equipped

with the kit.

a

B

You should therefore carefully check

the condition of the tyre sidewalls

before any operation.

It must never be used to inflate

the tyres of another vehicle, or any

other inflatable object (rubber ring,

rubber boat, etc.).

Driving with underinflated, flat or

punctured tyres can be dangerous

and may make the tyre impossible

to repair.

Avoid spillage on skin when han-

dling the repair liquid bottle. If drop-

lets do leak out, rinse them off with

plenty of water.

this repair is temporary

Keep the repair kit away from chil-

dren.

A tyre which has been punctured

should always be inspected (and

repaired, where possible) by a spe-

cialist.

Do not dispose of the empty bottle

in the countryside. Return it to your

approved dealer or to a recycling or-

ganisation.

The kit repairs tyres when

tread A has been dam-

aged by objects smaller

than 4 mm. It cannot repair

When taking a tyre which has been

repaired using this kit to be replaced,

you must inform the specialist.

all types of puncture, such as cuts

larger than 4 mm, or cuts in tyre

sidewall B.

The bottle has a limited service

life which is indicated on its label.

Check the expiry date.

When driving, vibration may be felt

due to the presence of the repair

product injected into the tyre.

Ensure also that the wheel rim is in

good condition.

Contact an approved dealer to re-

place the inflation tube and repair

product bottle.

5.3

tyre Pressure KIt (2/3)

Depending on the vehicle, in the event

of a puncture, use the kit located under-

neath the luggage compartment carpet.

with the ignition on,

1

2

3

4

– connect adapter 8 to the accessories

socket on the dashboard of the vehi-

cle;

Depending on the vehicle, remove the

central partition in the storage compart-

ment to access the inflation kit.

– unscrew the valve cap on the wheel

concerned and screw inflation

adapter 6 onto the valve;

Open the kit, remove caps 1 and 3 (the

cap must not be removed from the

bottle) then screw bottle 2 to its base 3.

5

6

– press switch 5 to inflate the tyre to

the recommended pressure (check

the label affixed to the edge of the

driver’s door);

– after a maximum of 7 minutes, stop

inflating and read the pressure (on

pressure gauge 4);

7

8

note: while the bottle is emptying

(approximately 30 seconds), pres-

sure gauge 4 will briefly indicate a

pressure of 6 bar, then the pressure

will drop.

– adjust the pressure: to increase

it, continue inflating with the kit, to

reduce it, turn button 7 located on

the inflation adapter.

Before using this kit, park

the vehicle at a sufficient

distance from traffic, switch

on the hazard warning

If the correct pressure cannot be

achieved, repair is impossible. Do

not drive the vehicle. consult an ap-

proved dealer.

lights, apply the handbrake, ask all

passengers to leave the vehicle and

keep them away from traffic.

Do not pull out the foreign

body causing the puncture

if it is still in the tyre.

5.4

tyre Pressure KIt (3/3)

– affix driving recommendation label 9

to the dashboard where it can easily

be seen by the driver;

Precautions when using the

kit

The kit should not be operated for more

than 15 consecutive minutes.

– store the kit;

– start the engine straight away and,

after driving a maximum of approx-

imately 2 miles (3 kilometres) or

10 minutes, stop and check the

pressure using the inflation kit. If it is

above 1.3 bar, adjust it to the rec-

ommended pressure (refer to the

label affixed to the edge of the driv-

er’s door), otherwise contact an ap-

proved dealer: repair is not possible.

9

Following repair with the kit,

do not travel further than

120 miles (200 km). In addi-

tion, reduce your speed and

under no circumstances exceed 48

mph (80 km/h). The sticker, which

you must affix in a prominent posi-

tion on the dashboard, reminds you

of this.

8

note: after using the inflation kit, you

should visit an approved Dealer to re-

place the inflation hose and the bottle

of repair product.

Once the tyre is inflated correctly:

– stop using the kit;

– close the integrated cap on the bottle

again;

– disconnect adapter 8;

Depending on the country or local

legislation, a tyre repaired with the

tyre pressure kit will need to be re-

placed.

Nothing should be placed

around the driver’s feet

as such objects may slide

under the pedals during

sudden braking manoeuvres and

obstruct their use.

Please be aware that a poorly tightened or missing valve cap can make

the tyres less airtight and lead to pressure loss.

Always use valve caps identical to those fitted originally and tighten them

fully.

5.5

tOOl KIt/wheel trIm – wheel

wheelbrace 1

2

Jack 2

When replacing the jack, fold it cor-

rectly and position the wheelbrace cor-

rectly before replacing it in its position.

1

e

hubcap tool 3

This tool is used to remove the wheel

trims.

c

D

3

4

5

wheel bolt guide 4

To finish loosening or starting to tighten

the wheel bolts.

B

6

towing hitch 5

Refer to the information on “Towing” in

Section 5.

The tool kit is located in the luggage

compartment: lift the carpet.

wheel trim

Remove it using the hubcap tool 3 by

connecting the hook in the recess pro-

vided next to the valve 6 (to attach the

metal clip).

The tools included in the tool kit depend

on the vehicle.

To refit wheel trim, align it with valve 6.

Push the retaining hooks in fully, start-

ing with side B near the valve, followed

by C and D, finishing at E opposite the

valve.

Do not leave the tools unsecured inside the vehicle as they may come

loose under braking. After use, check that all the tools are correctly

clipped into the tool kit, then position it correctly in its housing: there is a

risk of injury.

note: if you are using anti-theft bolts,

refer to the information on “Changing a

wheel”.

If wheel bolts are supplied in the tool kit, only use these bolts for the emergency

spare wheel: refer to the label affixed to the emergency spare wheel.

The jack is designed for wheel changing purposes only. Under no circumstances

should it be used for carrying out repairs underneath the vehicle or to gain access

to the underside of the vehicle.

5.6

changIng a wheel (1/2)

Offer up the jack 4 horizontally; the jack

head must be lined up with jacking

point 1 located on the underside of the

sill, closest to the wheel concerned, as

shown by arrow 2.

Vehicles equipped with a jack

and wheelbrace

If necessary, remove the wheel trim.

3

Use the wheelbrace 3 to slacken off the

wheel bolts. Position it so as to be able

to push from above.

Start cranking the jack up by hand to

align the base plate (which should be

pushed slightly under the vehicle).

1

2

Turn the wheelbrace until the wheel lifts

off the ground.

4

If the vehicle is not equipped with a

jack or wheelbrace, you can obtain

these from your approved dealer.

Switch on the hazard warn-

ing lights.

Keep the vehicle away from

traffic and on a level sur-

face where it will not slip (if neces-

sary, place a solid support under the

jack base).

If the vehicle is parked on

the hard shoulder, you must

warn other road users of

Apply the parking brake and engage

a gear (first or reverse, or P for auto-

matic transmissions).

Ask all the passengers to leave the

vehicle and keep them away from

traffic.

your vehicle’s presence

with a warning triangle or with other

devices as per the legislation apply-

ing to the country you are in.

To prevent any risk of injury

or damage to the vehicle,

only crank the jack until the

wheel you are replacing is

a maximum of 3 centimetres off the

ground.

5.7

changIng a wheel (2/2)

Undo the bolts and take off the wheel.

Fit the emergency spare wheel onto

the hub and rotate it until the mounting

holes in the wheel coincide with those

of the hub.

If bolts are supplied with the emergency

spare wheel, only use these bolts for

the emergency spare wheel. Tighten

the bolts, checking that the wheel is

correctly positioned on its hub and

lower the jack.

With the wheel on the ground, tighten

the bolts fully and have the tightness

of the bolts checked (tightening torque:

110 N.m) and the emergency spare

wheel pressure checked as soon as

possible.

anti-theft bolt

If you use anti-theft bolts, fit these

nearest the valve (wheel trim may

not be able to fit).

If you have a puncture, re-

place the wheel as soon as

possible.

Atyre which has been punc-

tured should always be inspected

(and repaired, where possible) by a

specialist.

5.8

tyres (1/3)

When the tyre tread has been worn to

the level of the wear indicators, they

become visible 2: it is then necessary

to replace your tyres because the tread

rubber is no more than 1.6 mm deep,

resulting in poor roadholding on wet

roads.

tyre and wheel safety

The tyres are the only contact between

the vehicle and the road, so it is essen-

tial to keep them in good condition.

2

1

You must make sure that your tyres

conform to local road traffic regulations.

An overloaded vehicle, long journeys

by motorway, particularly in very hot

weather, or continual driving on poorly

surfaced minor roads will lead to more

rapid tyre wear and affect safety.

maintaining the tyres

The tyres must be in good condition

and the tread form must have sufficient

depth; tyres approved by our Technical

Department have wear warning strips 1

that are indicators moulded into the

tread at several points.

When they need to be re-

placed, only tyres of the

same make, size, type and

profile should be used.

Incidents which occur when

driving, such as striking the

kerb, may damage the tyres

tyres fitted to the vehicle should

either be identical to those fitted

originally or conform to those

recommended by your approved

dealer.

and wheel rims, and could

also lead to misalignment of the

front or rear axle geometry. In this

case, have the condition of these

checked by an approved dealer.

5.9

tyres (2/3)

Pressures should be checked when the

tyres are cold; ignore higher pressures

which may be reached in hot weather

or following a fast journey.

tyre pressures

Fitting new tyres

Adhere to the tyre pressures (including

the emergency spare wheel). The tyre

pressures should be checked at least

once a month and additionally before

any long journey (refer to the label af-

fixed to the edge of the driver’s door).

For safety reasons, this op-

eration must be carried out

by a specialist.

If tyre pressures cannot be checked

when the tyres are cold, the normal

pressures must be increased by 0.2 to

0.3 bar (or 3 PsI).

Fitting different tyres may

change your vehicle as follows:

– It may mean that your vehicle no

longer conforms to current regu-

lations;

never deflate a hot tyre.

special note

Depending on the vehicle, there may

be an adapter which needs to be posi-

tioned on the valve before air is added.

– It may change the way it handles

when cornering;

Incorrect tyre pressures

lead to abnormal tyre wear

and unusually hot running.

These are factors which

may seriously affect safety and lead

to:

– It may cause the steering to be

heavy;

– It may affect the use of snow

chains.

– poor road holding,

– risk of bursting or tread separa-

tion.

emergency spare wheel

Refer to the information on the

“Emergency spare wheel” and in-

structions on “Changing a wheel” in

Section 5.

Please be aware that a

poorly tightened or miss-

ing valve cap can make the

tyres less airtight and lead

to pressure loss.

The pressure depends on the load

and the speed of use. Adjust the

pressure according to the condi-

tions of use (refer to the label affixed

to the edge of the driver’s door).

Always use valve caps identical to

those fitted originally and tighten

them fully.

5.10

tyres (3/3)

use in winter

chains

In all cases, we would recommend

that you contact an approved dealer

who will be able to advise you on

the choice of equipment which is

most suitable for your vehicle.

For safety reasons, fitting snow

chains to the rear axle is strictly for-

bidden.

chains cannot be fitted to tyres which

are larger than those originally fitted to

the vehicle.

snow or winter tyres

We would recommend that these be

fitted to all four wheels to ensure that

your vehicle retains maximum adhe-

sion.

warning: These tyres sometimes have

a specific direction of rotation and a

maximum speed index which may be

lower than the maximum speed of your

vehicle.

studded tyres

Chains may only be fitted

to tyres of the same size

as those originally fitted to

your vehicle.

This type of equipment may only be

used for a limited period and as laid

down by local legislation. It is neces-

sary to observe the speed specified by

current legislation.

changing a wheel

As the tyre pressure moni-

tor may take several min-

utes following driving to cor-

rectly determine the positions of the

wheels and the pressure values,

check the tyre pressures following

any operation.

Chains may be fitted, provided that

they are specific chains. We would

advise you to consult an approved

Dealer.

These tyres must, at a minimum, be

fitted to the two front wheels.

5.11

heaDlIghts: changing bulbs (1/2)

6

B

2

3

4

5

B

c

D

e

1

a

After opening the bonnet, pull tool A

upwards. Remove the two screws 1

from the headlight using the tool.

Do not touch the bulb glass. hold it

by its base.

When the bulb has been changed,

make sure you refit the cover correctly.

Daytime running light

Remove the cover C, unlock the bulb

holder 2 by rotating it.

Bulb type: P21w.

Pull the headlight forwards, sliding it in

its rails up to the end stop.

Discharge bulb dipped beam

headlight

Bulb type: D1s.

Dipped beam headlight D

After refitting the light, tighten the

screws 1 and reposition the tool cor-

rectly in its housing.

halogen dipped beam headlight

Unlock the two springs D, remove

the cover, then unclip the spring 3 to

remove the bulb 4.

Direction indicator lights

Rotate the bulb holder B to unlock it.

Bulb type: Py21w.

Bulb type: h7.

Due to the danger involved

in handling high-voltage de-

vices, this type of bulb must

be replaced by an approved

dealer.

It is essential to use anti U.V. 55W

bulbs so as not to damage the plastic

on the headlights.

5.12

heaDlIghts: changing bulbs (2/2)

To comply with current legislation,

or as a precaution, you can obtain

an emergency kit from an approved

dealer containing a set of spare

bulbs and fuses.

6

B

2

3

4

5

B

c

D

e

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

main beam headlight

Front side light

Remove the cover E, press the bulb

holder 5 downwards to unlock it.

Remove the cover E and pull the bulb

holder 6.

Bulb type: h7.

Bulb type: w5w.

The engine may be hot

when carrying out opera-

tions in close proximity. In

addition, the engine cooling

fan can come on at any moment.

Risk of injury.

5.13

heaDlIghts: additional/front fog lights

additional lights

If you wish to fit fog lights or long range

headlights to your vehicle, consult an

approved Dealer.

1

Front fog lights 1

However, because the front bumper

needs to be removed, you are advised

to have your bulbs replaced by an

approved dealer.

Any operation on (or modi-

fication to) the electrical

system must be performed

by an approved dealer

since an incorrect connection might

damage the electrical equipment

(harness, components and in partic-

ular the alternator). In addition, your

Dealer has all the parts required for

fitting these units.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.14

rear lIghts anD InDIcatOr lIghts: changing bulbs (1/6)

5

a

2

3

1

B

6

4

– loosen nut 1, press down on it to

release the front of the light (move-

ment A) then remove the nut;

Direction indicator lights 5

Bulb type: Py21w.

Five-door versions

Direction indicator lights/brake and

side lights

side light and brake light 6

Bulb type: P21/5w.

– from the outside, pull the light to-

– Unclip the cover to access nuts 1

and 2;

wards you (movement B);

– remove the bulb holder 3 by releas-

ing the clips 4.

refitting

– unscrew nut 2 without removing it

To refit, proceed in the reverse order,

taking care not to damage the wiring.

completely;

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.15

rear lIghts anD InDIcatOr lIghts: changing bulbs (2/6)

9

10

11

8

7

– Lower the tailgate, then pull light 9

reversing light 10

Bulb type: w16w.

Fog light/side light 11

Bulb type: P21/4w.

Five-door versions

towards the rear to release it.

(continued)

– Unscrew the bulb holder for the bulb

concerned.

Fog lights/side lights and reversing

lights

– From the luggage compartment,

unclip flap 7, then remove the

bolts 8.

5.16

rear lIghts anD InDIcatOr lIghts: changing bulbs (3/6)

14

13

12

17

18

16

15

16 side light/stop light

three-door versions

Bulb type: P21/5w.

17 Direction indicator light

Bulb type: Py21w.

– Unclip the access flap;

– unscrew nuts 12 and 13;

– from the outside, remove bolt 14,

then pull on the light;

18 reversing light

– remove the bulb holder by releasing

Bulb type: P21w.

the clips 15;

rear fog light

Undo bulb holder 19, turning it towards

the centre of the vehicle by accessing it

from underneath.

Bulb type: P21w.

The bulbs are under pres-

sure and can break when

replaced.

19

Risk of injury.

5.17

rear lIghts anD InDIcatOr lIghts: changing bulbs (4/6)

22

21

23

c

24

20

side light 22

sport tourer Versions

Bulb type: w5w.

reversing light 23

Bulb type: P21w.

Fog light 24

side lights/reversing lights and fog

lights

– From the luggage compartment,

unclip flap 20 (movement C), then

remove the bolts .

Bulb type: h21w.

– Lower the tailgate, then pull light 21

towards the rear to release it.

refitting

– Turn the bulb holder of the bulb con-

cerned a quarter of a turn.

To refit, proceed in the reverse order,

taking care not to damage the wiring.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.18

rear lIghts anD InDIcatOr lIghts: changing bulbs (5/6)

26

28

29

27

25

side light and brake light 28

estate versions

(continued)

Bulb type: P21/5w.

Direction indicator lights 29

Bulb type: Py21w.

Brake and side lights/direction

indicator lights

– Unclip covers 25 to access the nuts;

– unscrew the 2 nuts;

– from the outside, pull the light to-

wards you;

– remove the bulb holder 27 by releas-

ing the clips 26.

5.19

rear lIghts anD InDIcatOr lIghts: changing bulbs (6/6)

31

32

30

D

22

23

33

high level brake light 30

number plate lights 32

Indicator lights 33

Consult an approved Dealer.

– Unclip light 32 by pressing tab 31;

– Unclip indicator light 33 (using a

flat-blade screwdriver type tool po-

sitioned at D to move the indicator

light towards the front of the vehicle);

– remove the light cover to gain access

to the bulb.

Bulb type: w5w.

– turn the bulb holder a quarter of a

turn and take out the bulb.

Bulb type: w5w.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.20

InterIOr lIghtIng: changing bulbs (1/2)

1

2

a

B

3

4

courtesy light

Door lights

glove box light

– Position the 3 switches in the central

position;

Unclip light 2 (using a flat-blade screw-

driver or similar).

Open the access cover 3, you can then

unclip the bulb holder more easily 4.

– move the courtesy light backwards

(movement A) then tilt the front

downwards (movement B);

Turn the bulb holder a quarter of a turn

and take out the bulb.

Bulb type: c5w.

Bulb type: w5w.

– when removing the courtesy light,

ensure that you do not pull the elec-

trical wires;

– unclip the lens 1;

note: to remove the defective bulb, you

can use a flat-blade screwdriver or sim-

ilar.

The bulbs are under pres-

sure and can break when

replaced.

Bulb type: w5w.

Risk of injury.

5.21

InterIOr lIghtIng: changing bulbs (2/2)

7

6

8

5

Disconnect the light.

luggage compartment light

Press tab 6 to release lens 8 and

access bulb 7.

Unclip the light at 5 using a flat-blade

screwdriver or similar.

Bulb type: w5w.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.22

Fuses (1/2)

1

a

B

CORRECT INCORRECT

Fuse box

tweezers 1

If any electrical component does not

work, check the condition of the fuses.

Remove the fuse using tweezers 3, lo-

cated at the back of cover A or B.

Unclip cover A or B (depending on ve-

hicle).

To remove the fuse from the tweezers,

slide the fuse to the side.

Check the fuse in question

and replace it, if neces-

sary, by a fuse of the same

rating.

It is not advisable to use the free fuse

locations.

If a fuse is fitted where the rating is

too high, it may cause the electrical

circuit to overheat (risk of fire) in the

event of an item of equipment using

an excessive amount of current.

In accordance with local legislation

or as a precautionary measure:

Obtain an emergency kit containing

a set of spare bulbs and fuses from

an approved Dealer.

5.23

Fuses (2/2)

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

c

1

2

8 Interior rear-view mirror;

9 Rear screen wiper;

10 and 11 Rear electric windows;

12 ABS/ESP;

Some accessories are protected by

fuses located in the engine compart-

ment in fuse box C.

allocation of fuses

(the presence of certain fuses depends

on the vehicle equipment level)

However, because of their reduced ac-

cessibility, we advise you to have your

fuses replaced by an approved Dealer.

1 Electronic parking brake;

2 Brake lights;

13 Passenger electric window;

14 Windscreen washer;

15 Heated door mirrors;

16 Radio;

3 Automatic door locking;

4 Driver’s electric window;

5 Passenger compartment unit;

6 Direction indicator lights;

7 Navigation system;

17 Luggage compartment accessories

socket;

18 Rear seat accessories socket;

19 Cigarette lighter.

5.24

Battery: troubleshooting (1/2)

to avoid all risk of sparks:

connecting a battery charger

– Ensure that any electrical consumers

(courtesy lights, etc.) are switched

off before disconnecting or recon-

necting the battery.

the battery charger must be com-

patible with a battery with nominal

voltage of 12 volts.

Do not disconnect the battery when the

engine is running. Follow the instruc-

tions given by the manufacturer of

the battery charger you are using.

– When charging, stop the charger

before connecting or disconnecting

the battery.

– Do not place metal objects on the

battery to avoid creating a short cir-

cuit between the terminals.

– Always wait at least one minute after

the engine has been switched off

before disconnecting a battery.

Handle the battery with care

as it contains sulphuric acid,

which must not come into

contact with eyes or skin. If

it does, wash the affected area with

plenty of cold water. If necessary,

consult a doctor.

– Make sure that you reconnect the

battery terminals after refitting.

Ensure that naked flames, red hot

objects and sparks do not come into

contact with the battery as there is a

risk of explosion.

Special procedures may be

required to charge some

batteries. Contact your ap-

proved dealer.

The engine may be hot when car-

rying out operations in close prox-

imity. In addition, the engine cooling

fan can come on at any moment.

Avoid all risk of sparks which may

cause an immediate explosion, and

charge the battery in a well-venti-

lated area. Risk of serious injury.

Risk of injury.

5.25

Battery: troubleshooting (2/2)

starting the vehicle using the

battery from another vehicle

1

2

5

If you have to use the battery from an-

other vehicle to start, obtain suitable

jump leads (with a large cross section)

from an approved dealer or, if you al-

ready have jump leads, ensure that

they are in perfect condition.

5

B

2

a

the two batteries must have an iden-

tical nominal voltage of 12 volts. The

battery supplying the current should

have a capacity (amp-hours, Ah) which

is at least the same as that of the dis-

charged battery.

4

3

Ensure that there is no risk of contact

between the two vehicles (risk of short

circuiting when the positive terminals

are connected) and that the discharged

battery is properly connected. Switch

off your vehicle ignition.

Attach positive lead A to mounting 1

attached to (+) terminal 2 then to

(+) terminal 3 of the battery supplying

the current.

Attach the negative lead B to the

(–) terminal 4 of the battery supplying

the current, then to the (–) terminal 5

of the discharged battery.

Start the engine of the vehicle supply-

ing the current and run it at an interme-

diate engine speed.

Check that there is no con-

tact between leads A and B

and that the positive lead A

is not touching any metal

Start the engine. As soon as it is run-

ning, disconnect leads A and B in the

reverse order ( 5 - 4 - 3 - 2 ).

parts on the vehicle supplying the

current.

Risk of injury and/or damage to the

vehicle.

5.26

renault carD: battery

a

2

B

1

4

3

When refitting, proceed in the reverse

order, then press one of the buttons on

the card four times, close to the vehicle:

the next time the vehicle is started, the

message will disappear.

replacing the battery

Operating faults

When the message “Low card battery”

appears on the instrument panel, re-

place the RENAULTcard battery, press

button 1, pulling on emergency key 2,

then unclip cover 3 using tab 4.

If the battery is too weak to ensure cor-

rect operation, you may start (insert the

RENAULT card in the card reader) and

lock/unlock the vehicle (refer to the in-

formation on “Locking/unlocking the

doors” in Section 1).

note: it is not advisable to touch the

electronic circuit or contacts on the

RENAULT card when replacing the bat-

tery.

Remove the battery by pressing on one

side (movement A) and by lifting the

other (movement B) then replace it, en-

suring the polarity and model, shown

on cover 3 are respected.

Check that the cover is clipped shut.

Do not throw away your

used batteries; give them to

an organisation responsible

for collecting and recycling

batteries.

The batteries are available from approved Dealers, and their service life approxi-

mately two years. Check that there is no dye on the battery: risk of an incorrect

electrical contact.

5.27

FIttIng a raDIO

2

1

3

If your vehicle is not fitted with an audio

system, one can be fitted and locations

have been provided for:

– the radio 1;

– tweeter speakers 2;

– bass speakers 3.

To install any equipment, please con-

sult an approved dealer.

– In all cases, it is very important to follow the manufacturer’s instructions care-

fully.

– The specifications of the brackets and wires (available from our network) vary

depending on the equipment level of your vehicle and the type of radio.

radio location 1

Unclip the blanking cover. The aerial, +

and – supply and speaker wire connec-

tions are located behind it.

Consult an approved Dealer to find out the correct part number.

– No work may be carried out on the vehicle’s electrical or radio circuits, except

by approved dealers: an incorrectly connected system may result in damage

being caused to the electrical equipment and/or the components connected to

it.

5.28

accessOrIes

Before fitting an electrical or

If you are using an anti-theft

device, only attach it to the

brake pedal.

electronic device (particu-

larly for transmitters/receiv-

ers: frequency bandwidth,

power level, position of the aerial

etc.), ensure that it is compatible

with your vehicle.

Contact an approved dealer for this

information.

electrical and electronic

accessories

– Connect accessories

with a maximum power of

120 Watts only.

Fire hazard.

use of transmission/

receiving devices

(telephones, cB

equipment etc.).

– No work may be carried out on

the vehicle’s electrical or radio

circuits, except by approved

Dealers: an incorrectly con-

nected system may result in

damage being caused to the

electrical equipment and/or the

components connected to it;

Fitting after-market

accessories

If you wish to install acces-

sories on the vehicle: con-

Telephones and CB equipment with

integrated aerials may cause inter-

ference to the original electronic

systems fitted to the vehicle: it is ad-

visable only to use equipment with

an external aerial.

sult an approved dealer.

Also, to ensure the correct opera-

tion of your vehicle, and to avoid

any risk to your safety, we recom-

mend that you use only specific ac-

cessories, designed for your vehi-

cle, which are the only accessories

for which the manufacturer will pro-

vide a warranty.

– if the vehicle is fitted with any

aftermarket electrical equip-

ment, make sure that the unit

is correctly protected by a fuse.

Establish the rating and position

of this fuse.

Furthermore, we remind you of

the need to comply with the legis-

lation in force concerning the use

of such equipment.

5.29

wInDscreen wIPer BlaDes

1

Check the condition of the wiper

blades. You are responsible for their

service life:

– clean the blades, windscreen and

rear screen regularly with soapy

water;

B

4

a

2

c

– do not use them when the wind-

screen or rear screen are dry;

– free them from the windscreen or

rear screen when they have not

been used for a long time.

5

6

3

replacing windscreen wiper

blades 1

with the ignition on and engine

switched off, lower the windscreen

wiper stalk completely: they stop

slightly away from the bonnet.

rear screen wiper blade 4

– Lift wiper arm 6;

– In frosty weather, make

sure that the wiper blades

are not stuck by ice (to

avoid the risk of the motor

overheating).

– pivot blade 4 until some resistance is

met (movement C);

– depending on the vehicle, press

tab 5, then remove the blade by pull-

ing it (movement B).

– Check the condition of the wiper

blades.

Lift wiper arm 3, pull tab 2 (move-

ment A) and push the blade upwards.

Replace the wiper blades as soon

as they begin to lose efficiency

(approximately once a year).

to refit

Slide the blade along the arm until it

clips on. Make sure that the blade is

correctly locked in position. Return the

windscreen wiper stalk to the park po-

sition.

To refit the wiper blade, proceed in re-

verse order to removal. Make sure that

the blade is correctly locked in position.

Whilst changing the blade, take care

not to drop the arm onto the window

after it has been removed as this

may break the window.

5.30

tOwIng: breakdown (1/2)

Before towing, unlock the steering

column: with the clutch depressed,

engage first gear (lever in position n

or r for vehicles with automatic trans-

missions), insert the RENAULT card in

the card reader then press the engine

start button for two seconds.

The speed specified by current legis-

lation for towing must always be ob-

served. If your vehicle is the towing

vehicle, do not exceed the maximum

towing weight for your vehicle (refer to

the information on “Weights” in Section

6).

1

Reposition the lever to neutral (posi-

tion N for vehicles fitted with an auto-

matic gearbox)

towing a vehicle with an

automatic gearbox

2

The steering column unlocks, the ve-

hicle’s accessory functions are pow-

ered, and you can use the vehicle lights

(brake lights, hazard warning lights,

etc.). At night, the vehicle must be lit.

With the engine switched off, the trans-

mission is no longer lubricated. It is

preferable to tow this type of vehicle on

a trailer or tow it with the front wheels

off the ground.

Once you have finished towing, press

the engine start button twice (risk of

running down the battery).

under exceptional circumstances,

you may tow the vehicle with all four

wheels on the ground, only going for-

ward, with the gear lever in the n posi-

tion, and for a distance not exceeding

50 miles (80 km).

If the lever is stuck in P,

even though you are de-

pressing the brake pedal,

the lever can be released

manually. To do this, insert a rigid

rod in the hole 2, press the rod and

unlocking button 1 located on the

lever simultaneously.

Do not remove the

RENAULT card from the

reader when the vehicle is

being towed.

5.31

tOwIng: breakdown (2/2)

– Use a rigid towing bar.

If a rope or cable is used

(where the law allows this),

the vehicle being towed

must be able to brake.

4

– A vehicle must not be towed if it is

not fit to be driven.

5

6

– Avoid accelerating or braking

suddenly when towing, as this

may result in damage being

caused to the vehicle.

3

7

– When towing a vehicle, it is ad-

visable not to exceed 30 mph

(50 km/h).

Only use:

access to towing points

– at the rear, towing point 5;

Unclip cover 3 or 6 by sliding a flat tool

(or the key integrated in the RENAULT

card) under the cover.

– at the front, towing hitch 4 (lo-

cated in the tool kit).

screw in towing hitch 7 fully: as

much as possible by hand at first, then

finish by tightening it using the wheel-

brace.

These towing points may only be used

for pulling the vehicle, never for lifting it

either directly or indirectly.

Use only towing hitch 7 and the wheel-

brace located under the luggage com-

partment carpet in the tool kit (refer

to the information on the “Tool kit” in

Section 5).

When the engine is

stopped, steering and brak-

ing assistance are not op-

erational.

Do not leave the tools unse-

cured inside the vehicle as

they may come loose under

braking.

5.32

OPeratIng Faults (1/5)

the following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact

an approved dealer as soon as possible.

using the renault card

POssIBle causes

what tO DO

The RENAULT card does not lock or

unlock the doors.

Card battery is flat.

Replace the battery. You can still lock/

unlock and start your vehicle (refer to the

information on “Locking/unlocking the

doors” in Section 1 and “Starting/Stopping

the engine” in Section 2).

Use of appliances operating on the

same frequency as the card (mobile

phone, etc.).

Stop using the equipment or use the in-

tegrated key (refer to the information on

“Locking/unlocking the doors” in Section 1).

Vehicle located in a high electromag-

netic radiation zone.

Use the key integrated in the card (refer to

the information on “Locking/unlocking the

doors” in Section 1).

Vehicle battery flat.

5.33

OPeratIng Faults (2/5)

the starter is activated

POssIBle causes

what tO DO

The instrument panel indicator lights

are weak or fail to light up and the

starter does not turn.

Battery terminals not tight, battery

terminals disconnected or oxidised.

Retighten or reconnect the terminals, or

clean them if they are oxidised.

Discharged battery or not opera-

tional.

Connect another battery to the faulty bat-

tery. Refer to information on “Battery: trou-

bleshooting” in Section 5 or replace the bat-

tery if necessary.

Do not push the vehicle if the steering

column is locked.

The engine will not start.

Starting conditions are not fulfilled.

Refer to the information on “Starting/stop-

ping the engine” in Section 2.

The hands-free RENAULT card

does not work.

Insert the card in the card reader in order to

start the engine.

Refer to the information on “Starting/stop-

ping the engine” in Section 2.

The engine cannot be switched off.

Card not detected.

Electronic fault.

Insert the card in card reader.

Press the starter button quickly five times.

5.34

OPeratIng Faults (3/5)

On the road

POssIBle causes

what tO DO

The steering column remains locked.

Steering wheel locked.

Move the steering wheel while pressing the

engine start button (refer to the information

on “Starting the engine” in Section 2).

Coolant boiling in the coolant reser-

voir.

Mechanical fault: damaged cylinder

head gasket.

Stop the engine.

Contact an approved dealer.

Smoke under the bonnet.

Short-circuit or cooling system leak.

Stop, switch off the ignition, stand away

from the vehicle and contact an approved

dealer.

The oil pressure warning light comes

on:

while cornering or braking

The level is too low.

Loss of oil pressure.

Top up the engine oil level (refer to the in-

formation on “Engine oil level: topping up/

filling” in Section 4).

is slow to go out or remains lit

under acceleration

Stop the vehicle and contact an approved

dealer.

White smoke from the exhaust.

This is not necessarily a fault. Smoke

may be caused by regeneration of the

particle filter.

Refer to the information on “Special fea-

tures of diesel versions” in Section 2.

5.35

OPeratIng Faults (4/5)

On the road

POssIBle causes

what tO DO

Steering becomes heavy.

Assistance overheating.

Consult an approved dealer.

The engine overheats. The coolant

temperature indicator is in the warn-

ing zone and warning light ®

comes on.

Engine cooling fan not working.

Stop the vehicle, switch off the engine and

contact an approved dealer.

Coolant leaks.

Check the coolant reservoir: it should con-

tain fluid. If there is no coolant, consult an

approved dealer as soon as possible.

Vibrations.

Tyres not inflated to correct pres-

sures, incorrectly balanced or dam-

aged.

Check the tyre pressures: if this is not the

problem, have them checked by an ap-

proved dealer.

radiator: If there is a significant lack of coolant, remember that it must never be topped up using cold coolant while

the engine is very warm. After any procedure on the vehicle which has involved even partial draining of the cooling

system, it must be refilled with a new mixture prepared in the correct proportions. Reminder: only products approved

by our Technical Department may be used for this purpose.

5.36

OPeratIng Faults (5/5)

electrical equipment

POssIBle causes

what tO DO

The wipers do not work.

Wiper blades stuck.

Free the blades before using the wipers.

Faulty electrical circuit.

Faulty electrical controls.

Blown bulb.

Consult an approved dealer.

The wiper does not stop.

Direction indicators flashing more

quickly.

Front: contact an approved dealer.

Rear: replace the bulb.

The direction indicators do not work.

The lights do not come on or go off.

Faulty electrical circuit.

Consult an approved dealer.

Faulty electrical circuit or control.

Traces of condensation in the lights.

Traces of condensation may be a nat-

ural phenomenon caused by varia-

tions in temperature.

In this situation, these traces soon dis-

appear when the lights are switched

on.

5.37

5.38

Practical advice for Your Renault Megane SUV Third Generation (2009-2016)

Related Topics

Popular Owner Manuals

Latest Owner Manuals