Get Getting to know your vehicle Guide for Renault Scenic 4 Door Second Generation (2003-2009)

Section 1: Getting to know your vehicle

RENAULT Card: general information, use, deadlocking .............................................................. 1.02 ➟ 1.08

Doors ............................................................................................................................................... 1.09 ➟ 1.13

RENAULT Anti-Intruder Device (RAID) ................................................................................................... 1.14

Engine immobiliser .......................................................................................................................... 1.15 - 1.16

Headrests - Seats ............................................................................................................................ 1.17 ➟ 1.19

Seat belts ......................................................................................................................................... 1.20 ➟ 1.26

Additional methods of restraint .................................................................................................... 1.27 ➟ 1.33

to the front seat belts ................................................................................................................. 1.27 ➟ 1.30

to the rear seat belts ............................................................................................................................... 1.31

side protection devices .......................................................................................................................... 1.31

Child safety ..................................................................................................................................... 1.34 ➟ 1.44

Steering wheel ............................................................................................................................................ 1.45

Driver’s position ............................................................................................................................. 1.46 ➟ 1.49

Instrument panel ............................................................................................................................ 1.50 ➟ 1.66

Trip computer and warning system .......................................................................................... 1.56 ➟ 1.66

Time and external temperature .................................................................................................................. 1.67

Rear-view mirrors ............................................................................................................................. 1.68 - 1.69

Audible and visible signals ....................................................................................................................... 1.70

Lighting and exterior signals ......................................................................................................... 1.71 ➟ 1.73

Headlight beam adjustment ....................................................................................................................... 1.74

Wipers/washers .............................................................................................................................. 1.75 ➟ 1.77

Fuel tank (filling with fuel) ............................................................................................................. 1.78 - 1.79

1.01

RENAULT CARD: general information

The RENAULT Card is used for:

- locking/unlocking the doors and

boot and the fuel filler flap (refer

to the following pages),

24088

1

Advice

2

- the automatic closure of electric

windows and the sunroof, refer to

the information on Electric

windows with automatic closing

Do not keep your RENAULT Card

where it could be bent or damaged

accidentally, such as in a back

pocket where you might sit on it.

3

in Section

vehicle),

3

(depending on

- for starting the engine, refer to

“Starting the engine” in Section 2.

4

Battery life

It is supplied by a battery which

must be replaced when the message

“Change card battery” appears on

the instrument panel (refer to the

information on RENAULT Card:

battery in Section 5).

RENAULT Card

1 - Unlocking the doors and boot.

Driver’s responsibility

2 - Locking all the doors and boot.

3 - Locking/Unlocking the boot.

4 - Emergency key.

Never leave your vehicle

with the RENAULT card

inside and never leave a

child (or a pet) unsupervised. They

might start the engine or operate

electrical equipment such as the

electric windows and there is a

risk that they may trap part of their

body (neck, arms, hands, etc.).

Range of the RENAULT Card

This varies according to the

environment. It is therefore

important to take care when

handling the RENAULT Card that

you do not lock or unlock the doors

by inadvertently pressing the

buttons.

Risk of serious injury.

1.02

RENAULT Card: general information (continued)

24089

4

Replacement:

need

for

an

5

additional RENAULT Card

If you lose your RENAULT card or

require another, you can obtain one

from your RENAULT Dealer.

If a RENAULT card is replaced, it

will be necessary to take the

vehicle and all RENAULT cards to

your RENAULT Dealer to initialise

the system.

Integral emergency key 4 or

separate emergency key 5

(depending on vehicle)

You can use up to four RENAULT

Cards per vehicle.

It is only used in exceptional

circumstances. It locks or unlocks

the left-hand side door if the

RENAULT Card does not work:

For instructions on how to use

the emergency key, see the

Faulty RENAULT Card

Locking/unlocking

section.

the

doors

Always make sure the battery is in

good condition; they have a service

life of approximately two years.

- vehicle located in

a

high

Having entered the vehicle using

the emergency key, insert the

RENAULT Card in the card reader

in order to be able to start the

engine.

electromagnetic radiation zone,

See the information on RENAULT

card: Batteries, in Section 5.

- use of devices using the same

frequency as the card,

- wear on the RENAULT Card

battery, discharged battery, etc.

1.03

REMOTE CONTROL RENAULT CARD: use

Locking the doors

Press the locking button 2.

24088

1

The side indicator lights and hazard

warning lights flash twice to

indicate that the doors have been

locked:

2

- if an opening element (door or the

3

luggage compartment) is open or

not properly shut, or if

a

RENAULT card is still in the

reader, the doors and luggage

compartment quickly lock then

unlock and the hazard warning

lights and side indicators do not

flash.

Unlocking the doors

Press unlocking button 1.

Unlocking is indicated by one flash

of the hazard warning lights and the

side indicators.

Unlocking/locking the luggage

compartment only

Press button 3 to unlock or lock the

luggage compartment.

The hazard warning lights and side

indicators flash once to indicate

unlocking if the vehicle doors are

locked.

Special notes (for some countries):

- The driver's door only can be

opened by pressing button 1,

- the other doors can be unlocked

by pressing button 1 twice.

The hazard warning lights and side

indicators flash twice to indicate

that the luggage compartment is

locked if the vehicle doors are

locked.

The card buttons are deactivated

when the engine is running.

1.04

RENAULT CARD IN HANDS-FREE MODE: use

2

4

3

1

Unlocking the doors and

RENAULT card in hands-free

mode

In addition to the RENAULT card

remote functions, this enables the

following to be carried out without

touching the key card (in hands-free

mode):

luggage compartment

Walk up to your vehicle carrying

your RENAULT card.

As soon as you place your hand on

the door handle 2 the vehicle will

unlock. When you press button 3 or

4, only the luggage compartment

will unlock.

- unlocking/locking of the doors

and boot and fuel filler flap if the

card is within access zone 1,

Unlocking is indicated by one flash

of the hazard warning lights and the

side indicators.

- starting the engine when the card

is

inside

the

passenger

to the

Never leave your vehicle

with the RENAULT Card

inside.

compartment

(refer

information on Starting the

engine in Section 2).

1.05

RENAULT CARD IN HANDS-FREE MODE: use (continued)

If you wish to check the doors are

locked after locking with the

RENAULT Card or the buttons

on the handles, you have

approximately three seconds to try

the door handles without unlocking

them.

6

2

After this delay, the Hands-Free

mode is activated once again, and

any movement of the handle will

unlock the doors.

5

Locking the doors and luggage

compartment

If you have the RENAULT Card on

you, with the doors and luggage

compartment closed, press button 5

on one of the handles 2 or button 6

on the luggage compartment.

The side indicators and hazard

warning lights flash twice to

indicate that the doors have locked.

Driver's responsibility

If a door or the tailgate is open or not

properly shut, or if a RENAULT

Card is present in the reader, the

doors or tailgate quickly lock then

unlock and the hazard warning

lights and side indicators do not

flash.

Never leave a child (or

animal) alone in the

vehicle

with

the

RENAULT Card inside. They

might start the engine or operate

electrical equipment (electric

windows) and there is a risk that

they may trap part of their body

(neck, arms, hands, etc.). Risk of

serious injury.

Note: the RENAULT Card must be

within the vehicle's access zone for

locking with the buttons to be

possible.

1.06

DEADLOCKING

To activate deadlocking

Vehicles equipped with electric

windows on the rear doors:

24088

- press button 1 twice in quick

succession.

1

- or press the exterior door handle

buttons

or

the

luggage

compartment logo twice in quick

succession.

Vehicles fitted with manual rear

door windows:

Before leaving the vehicle, press the

2

lower part of switch

2

(the

integrated indicator light lights up).

Press the top part of the switch to

unlock the doors.

Deadlocking the opening elements

(for some countries)

In all cases locking is indicated by

the hazard warning lights flashing

five times.

This allows you to lock the doors,

luggage

depending

compartment

and,

the

on

vehicle,

Note: this function can be activated

by two presses in quick succession

on the door handle buttons on the

same side of the vehicle (e.g. front

left-hand side/rear left-hand side or

front + rear right-hand side).

passenger side storage compartment

and to prevent the doors from being

opened using the interior handles

(for example, by breaking the

window and then trying to open the

door from the inside).

Never use deadlocking if

someone is still inside the

vehicle.

1.07

RENAULT CARD IN RESTRICTED MODE

24088

1

2

4

3

Using the RENAULT Card in

restricted mode

In certain situations (vehicle in

the hands of a third party: parking

valet, mechanic, etc.) you may

wish to restrict the operation of

the RENAULT card.

When the RENAULT card is in

restricted mode it will only permit

unlocking of the driver's door or the

fuel filler flap and starting of the

engine (the storage compartment on

the passenger side and the luggage

compartment remain locked).

Interior locking / unlocking switch

4 is deactivated while the vehicle is

used with the RENAULT card in

restricted mode.

Obtain two cards. Insert one card

into

card

reader

3

then

To cancel restricted mode, start the

vehicle with the RENAULT card in

non-restricted mode.

simultaneously press lock button

1 and boot button 2 on the second

card. The vehicle is locked and

then the driver’s door unlocks.

Only one RENAULT card may

be restricted at any one time.

While one RENAULT card is being

used in restricted mode, the second

card remains fully operational.

The RENAULT card inserted in

the card reader switches to

restricted use.

1.08

OPENING AND CLOSING THE DOORS

Card reminder buzzer

A beep will let you know if you

have left the card in the reader when

you open the driver's door, and the

message “Remove card” will appear

on the instrument panel.

Special note

2

Lights and accessories operating

when the engine is switched off

(radio, air conditioning, etc.) will

continue to function.

1

They will stop when the driver's

door is opened or the vehicle is

locked.

Opening the doors from the

outside

Once the doors have been unlocked

or with the Hands-Free RENAULT

Card on your person, pull handle 1

towards you to open the door.

Opening the doors from the

inside

Pull handle 2.

Door/boot open reminder

If a door or the boot is open or not

closed properly, the message “door

open” or “boot open” (depending

on the opening element) will appear

on the instrument panel as soon as

Lights on warning buzzer

If you have turned off the ignition

and left the lights switched on an

alarm will sound when a door is

opened.

the vehicle reaches

(10 km/h).

6

mph

1.09

OPENING AND CLOSING THE DOORS (continued)

Rear door locking must be

reactivated

following

disconnection of the battery

by pressing switch 1.

2

1

Safety of rear occupants

The driver can inhibit

operation of the rear

electric windows and

doors by pressing switch 1 on the

side with the symbol.

Child safety

Driver’s responsibility

Vehicles fitted with switch 1 with

Locking the doors manually

Never leave your vehicle without

removing the RENAULT card

from inside and never leave a

child (or a pet) inside. With the

key in the ignition it would be

possible to operate the electric

windows and there is a risk that a

child or animal may be seriously

injured (by trapping his or her

neck, arm, hand, etc.). If

something gets trapped, reverse

the direction of travel as soon as

possible by pressing the relevant

switch.

integrated indicator light

To make it impossible for the rear

doors to be opened from the

inside, move lever 2 on each door

and check from the inside that the

doors are securely locked.

Press switch 1 to prevent the

operation of the rear electric

windows and opening of the rear

doors.

The indicator light in the switch

lights up to confirm that the doors

are locked.

If there is a fault, you

will hear a beep and the

integrated indicator will

not light up.

1.10a

OPENING AND CLOSING THE DOORS (continued)

3

Other cases

To make it impossible for

the rear doors to be opened

from the inside, press switch 3

and check from the inside that the

doors are securely locked.

1.10b

1.10c

LOCKING/UNLOCKING THE DOORS

Locking/unlocking the doors

from the outside

This is done using the RENAULT

card: refer to the RENAULT card

information in Section 1.

In certain cases, the RENAULT card

may not work:

- if the vehicle is located in a zone

of high electromagnetic radiation,

A

2

1

- use of appliances operating on the

same frequency as the card

(mobile phone, etc.);

- drain on the RENAULT Card

battery, flat battery, etc.

It is then possible:

Using emergency key 2 built

- to use the emergency key

(integrated into the card or,

depending on the vehicle,

separate) in the front left-hand

door;

- to manually lock each of the doors

(see the following page);

into the RENAULT card

Remove cover A from the front

left-hand door (using the tip of the

emergency key) at notch 1.

Insert key 2 into the lock of the front

left-hand door and lock or unlock.

Move it upwards to remove cover A.

- to use the door locking/unlocking

control inside the vehicle (refer to

the information on Locking and

unlocking from the inside in

Section 1).

1.11

LOCKING/UNLOCKING THE DOORS (continued)

4

3

Using the separate emergency

Locking the doors manually

With the door open, pivot bolt 4

(using a flat-blade screwdriver or

similar tool) and close the door.

key 3 (depending on vehicle)

Insert key 3 in the front left-hand

front door and lock or unlock the

door.

This means that the doors are then

locked from the outside.

The doors may then only be opened

from the inside or by using the key

in the front left-hand door.

1.12

LOCKING/UNLOCKING THE DOORS (continued)

Locking the doors and tailgate

without the RENAULT Card

Doors and boot locking status

indicator light

With the engine switched off and a

front door open, press switch 5 for

more than five seconds.

When the ignition is switched on,

the indicator light incorporated in

switch 5 tells you whether the doors

and boot are locked:

- indicator light on, the doors and

boot are locked,

On closing the door, all of the doors

and the luggage compartment will

be locked.

5

- indicator light off, the doors and

boot are unlocked,

It will only be possible to unlock the

vehicle from outside using the

RENAULT Card.

When you lock the vehicle from the

outside, the indicator light remains

lit for approximately one minute,

then goes out.

Command

for

locking/

unlocking from the inside

Switch 5 simultaneously controls

the doors, luggage compartment

and fuel filler flap and, depending

on vehicle, the passenger side

storage compartment.

If an opening element (door or the

luggage compartment) is open or

not closed properly, the doors and

luggage compartment lock/unlock

quickly.

If you decide to keep the

doors locked when you

are driving, remember

that it may be more

Never leave your vehicle

with the RENAULT Card

inside.

difficult for those assisting you

to gain access to your vehicle in

the event of an emergency.

If you are transporting an object

with

a

door or the luggage

compartment open, press with the

engine stopped, switch 5 for more

than five seconds to lock the other

opening elements.

1.13

RAID (RENAULT ANTI-INTRUDER DEVICE)

You must first decide if you want to

activate this function.

Operating faults

If you notice a fault (automatic

locking does not work, warning

light incorporated in button 1 does

not light up when the doors are

locked, etc.), first check that all the

doors are closed properly. If they are

closed correctly, contact your

RENAULT Dealer.

To activate

With the ignition on, press central

door locking button 1 for about five

seconds, until two beeps are heard.

To deactivate it

1

With the ignition on, press central

door locking button 1 for about five

seconds, until one beep is heard.

Operating principle

When the vehicle moves off,

the system locks the doors

automatically as soon as you reach a

speed of 6 mph (10 km/h).

The door isunlocked:

- by pressing door unlocking button 1.

- by opening a front door (vehicle

If you decide to keep the

doors locked when you

stationary).

Note: If a door is opened, If a door

is opened, it will automatically

lock once more when the vehicle

reaches a speed of approximately

6 mph (10 km/h).

are driving, remember

that it may be more

difficult for those assisting you

to gain access to your vehicle in

the event of an emergency.

1.14

ENGINE IMMOBILISER

This prevents the vehicle being

driven by anyone not in possession

of the vehicle's RENAULT Card.

2

The vehicle is automatically

protected a few seconds after the

engine is switched off.

1

Operating principle

When the engine is started, warning

light 1 remains lit for a few seconds

and then goes out (refer to the

information on Starting the engine

in Section 2).

If the code is not recognised, the

card reader flashes quickly and the

vehicle will not start.

Any unauthorised work

carried out on the engine

immobiliser (computers,

wiring, etc.) could be

dangerous. It must be carried out

by trained RENAULT network

personnel.

1.15

ENGINE IMMOBILISER (continued)

24045

1

2

Indicator lights

Vehicle protection indicator light

After the ignition has been switched

off, warning light 1 flashes and the

vehicle is protected.

If the RENAULT Card is faulty

(rapid flashing of the card reader),

use the second RENAULT Card

(supplied with the vehicle) if

possible.

Operating fault indicator light

If the warning light continues to

flash or remains lit following an

attempt to start the engine, this

indicates an operating fault in the

system.

In this case, it is essential to contact

a RENAULT Dealer who alone is

qualified to repair the engine

immobiliser system.

If there is interference and/or the

Hands-Free RENAULT Card is not

recognised, insert it into card reader 2.

1.16

FRONT HEADRESTS

A

2

1

To raise the headrest

To fit the headrest

Press button

2

and raise the

Slide it upwards to the required

height.

headrest until it comes free.

To lower the headrest

To refit the headrest

Move the headrest gently upwards.

Insert the headrest rods into the

sleeves, with the notches facing

forwards.

The headrest is an important

safety component. Ensure

that it is in place and in the

correct position. The distance

between your head and the

headrest should be as small as

possible. The top of your head

should be in line with the top of

the headrest.

Move tab 1 forwards and lower the

headrest to the required height.

Move tab 1 forwards and lower the

headrest to the required height.

To adjust the angle of the headrest

Depending on the vehicle, move

section A of the headrest forwards

or backwards until it feels

comfortable.

1.17

FRONT SEATS

To tilt the seatback

For safety reasons, make

these adjustments only

when the vehicle is

stationary.

Lift handle 3 and incline the

seatback to the desired position

then release.

1

3

Table function

Depending on the vehicle the

passenger seatback may be folded

down onto the seat base to create a

table.

2

Pull handle

3

on the front

passenger seat and completely

lower the seatback.

To move a seat forwards or

backwards

Lift handle 1 to release. Release

the handle in the desired position

and check that the seat has locked

in place properly.

To avoid hindering the

efficient operation of the

seat belts, you are advised

to keep the seat belt on

your shoulder.

Make sure that the seatback is

locked in place correctly.

To adjust the driver’s seat height:

Move the lever 2 as many times as

necessary:

Nothing should be placed on the

floor area in front of driver as

objects could slide under a pedal

during sudden braking manoeuvres

and obstruct its use.

- upwards to raise the seat,

- downwards to lower the seat.

1.18

FRONT SEATS (continued)

4

5

To adjust the lumbar support on the

driver’s seat

Move tumblewheel 4.

Heated seats

With the ignition switched on,

move switch 5 of the required seat.

A message will be displayed on the

instrument panel.

The system, which is equipped with

a thermostat, determines whether

heating is necessary.

1.19

SEAT BELTS

Always wear your seat belt when

travelling in your vehicle. You must

also comply with the local

legislation of the particular country

you are in.

Adjusting your driving position

- Sit well back in your seat (having

removed your coat or jacket). This

is essential to ensure your back is

positioned correctly.

Before driving off:

- First ensure that your driving

position is correct,

- Then adjust your seat belt to

provide maximum protection.

- Adjusting the distance between

the seat and the pedals. Your seat

should be as far back as possible

while still allowing you to be able

to fully depress the clutch pedal.

The seatback should be adjusted

so that your arms are slightly bent

when you hold the steering wheel.

1

2

- Adjusting the position of your

headrest. For maximum safety, the

top of your head should be in line

with the top of the headrest.

Adjusting the seat belts

Sit with your back firmly against the

seatback.

- Adjusting the height of the seat.

This adjustment allows you to

select the seat position which

offers you the best possible vision.

Shoulder strap 1 should be as close

to the base of your neck as possible

but not on it.

Incorrectly adjusted seat

belts may cause injuries

in the event of an

accident.

The lap strap 2 should be worn flat

over your thighs and against your

pelvis.

- Adjust the position of the steering

wheel.

Even pregnant women should

wear a seat belt. In this case,

ensure that the lap belt is not

exerting too much pressure on

the abdomen without allowing

any slack.

The belt should be worn so that it is

as close to your body as possible, i.e.

avoid wearing heavy clothing or

keeping bulky objects under the

belts.

1.20

SEAT BELTS (continued)

Locking (continued)

If your belt becomes completely

jammed:

- pull the belt slowly but firmly so

that just over an inch (3 cm)

unwinds;

3

- then allow the belt to rewind

automatically;

1

- unwind it again;

- if there is still a problem, contact

your RENAULT Dealer.

4

5

6

Seat

belt

reminder

ç

warning light

Adjusting the height of the seat

belt

Press button 3 to select the seat belt

adjustment height so that shoulder

strap 1 is worn as above:

To fasten

This warning light on the

Unwind the belt slowly and

smoothly and ensure that tongue 4

locks into buckle 6 (check that it is

locked by pulling tongue 4). If the

belt jams before it is secured, allow

it to return before attempting to

unwind it again.

instrument panel goes out to let

you know that the seat belt has

been correctly fastened.

- to lower the seat belt, push button

Unlocking

Press button 5 on buckle 6 and the

seat belt will be rewound by the

inertia reel.

3

and lower the seat belt

simultaneously,

- to raise the seat belt, push button 3

upwards.

Guide the buckle to help the

operation.

Make sure that the seat belt is

locked in position correctly after

you have adjusted it.

1.21

REAR SEAT BELTS: 5-seat Scénic

2

1

5

3

6

4

Rear side seat belts

Unwind the belt 1 slowly from its

housing.

Click the last sliding tongue 5 into

red buckle 6.

For your comfort, you can pass the

belt through the belt guide 2.

Click tongue 3 into black catch 4.

Check that the rear seat

belts are positioned and

operating correctly each

time the rear seats are

moved.

Rear seat functions

Refer to Section 3.

1.22

REAR SEAT BELTS: 5-seat Scénic (continued)

7

9

8

10

Rear centre belt

Unwind belt 7 slowly from its

housing.

Click tongue 8 into the black buckle.

Click the last sliding tongue 9 into

red catch 10.

Check that the rear seat

belts are positioned and

operating correctly each

time the rear seats are

moved.

Rear seat functions

Refer to Section 3.

1.23

REAR SEAT BELTS: 7-seat Grand Scénic

5

4

6

1

2

8

3

7

9

Second row rear seat

Rear side seat belts

Rear centre belt

Slowly unwind belt 1.

Slowly unwind belt 4 from its

Click the last sliding tongue 8 into

red buckle 9.

housing.

Fasten sliding tongue

corresponding red buckle 3.

2

into

For your comfort, you can pass the

belt through the belt guide 6.

Click tongue 5 into black catch 7.

Check that the rear seat

belts are positioned and

operating correctly each

time the rear seats are

moved.

Rear seat functions

Refer to the information on “Rear

seats: operation” in Section 3.

1.24

REAR SEAT BELTS: 7-seat Grand Scénic (continued)

10

11

13

12

14

Third row rear seat

Slowly unwind belt 10.

Click the last sliding tongue 13 into

red buckle 14.

Rear seat functions

Refer to the information on “Rear

seats: operation” in Section 3.

Clip sliding tongue 11 into

corresponding black buckle 12.

Check that the rear seat

belts are positioned and

operating correctly each

time the rear seats are

moved.

1.25

SEAT BELTS (continued)

The following information applies to both the vehicle's front and rear seat belts.

- No adjustments may be made to the original component parts of the restraint system (belts, seats and their

mountings).

For special applications (e.g. fitting child seats) contact your RENAULT Dealer.

- Do not use devices which give any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely

risks causing injury in the event of an accident.

- Never wear the shoulder strap under the arm or behind the back.

- Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt

around them.

- The belt should never be twisted.

- Seat belts should be replaced after a serious accident. Likewise, replace your seat belts as soon as they show any signs

of wear.

- When refitting the rear seats, take care that the seat belts are correctly positioned so that they can be used correctly.

- If necessary, readjust the position and tightness of the belt.

- Make sure that the tongue is inserted into the appropriate buckle.

1.26

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS

These are:

- After an accident, have

the entire restraint

system checked

- buckle pretensioners,

- lap strap pretensioners,

- chest force limiters,

- No operation whatsoever is

permitted on any part of the

system (pretensioners, airbags,

computers, wiring) and the

system components must not be

reused on any other vehicle, even

if identical.

- driver and passenger front

airbags.

These systems are designed to act

independently or together when the

vehicle is subjected to a frontal

impact.

- To avoid premature triggering of

the system which may cause

injury, only qualified RENAULT

Network personnel may work on

the pretensioner and airbag

system.

Depending on the force of the

impact the system may activate:

- seat belt locking,

- the buckle pretensioner (which is

triggered to take up the seat belt

play),

- the lap belt pretensioner to keep

the occupant in their seat, the low

volume front airbag and the force

limiters,

2

1

Pretensioners

The pretensioners hold the seat belt

against the body, holding the

occupant more securely against the

seat, thus increasing the seat belt's

efficiency.

- Testing of the electric trigger

system may only be carried out

by a specially trained technician

using special equipment.

- the large volume front airbag.

In the event of a severe frontal

impact and if the ignition is

switched on, the system may engage

the following depending on the

force of the impact:

- When the vehicle is scrapped,

contact your RENAULT Dealer

for disposal of the pretensioner

and airbag gas generators.

- piston 1 which instantly retracts

the seat belt;

- piston 2 on the front seats.

1.27

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (continued)

Force limiter

Driver and passenger airbags

Above a certain severity of impact,

this mechanism is used to limit the

force of the belt against the body so

that it is at an acceptable level.

Fitted to the driver and passenger

side.

The presence of this equipment is

indicated by the word “Airbag” on

the steering wheel and the

dashboard (airbag zone A) and a

label on the lower part of the

windscreen or on the sun visor.

A

Each airbag system consists of:

- an airbag and gas generator fitted

on the steering wheel for the

driver and in the dashboard for the

front passenger,

- an intelligent computer for both

systems, which includes an

impact sensor and

a

monitor

controlling the electrical trigger

system for the gas generator.

- A single warning light

the instrument panel.

on

The airbag system is based on

principles of pyrotechnics. This

explains why, when the airbag

inflates, it will generate heat,

produce smoke (this does not mean

that a fire is about to start) and

make a noise upon detonation. In a

situation where an airbag is

required,

it

will

inflate

immediately and this may cause

some minor, superficial grazing to

the skin or other problems.

1.28

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (continued)

1

Operation

This system is only operational

when the ignition is switched on.

Special feature of the front

airbag

The front airbag has two inflation

volumes and includes an internal

ventilation system to prevent burns

which could be caused by escaping

gases:

Operating faults

When the ignition is switched on,

In a severe frontal impact, the

airbags inflate rapidly, cushioning

the impact of the driver's head and

chest against the steering wheel and

the front passenger's head against

the dashboard. The airbags then

deflate immediately so that the

passengers are not in any way

hindered from leaving the vehicle.

warning light 1

lights up on

the instrument panel, then goes out

after a few seconds.

- “small volume” airbag, this is the

first stage of operation,

If it does not light up when the

ignition is switched on, or comes on

when the engine is running, there is

a fault in the system.

- “large volume” airbag, the airbag

seams rip so that a larger volume

of gas is released into the bag (for

the most severe impacts).

Deployment of the airbag is

modified according to the severity

of the impact and the position of the

driver's seat on its runners.

Consult your RENAULT Dealer as

soon as possible. Your protection

will be reduced until this fault is

rectified.

1.29

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (continued)

All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent

the risk of serious injuries caused by items which may be dislodged when the airbag inflates.

Warnings concerning the driver’s airbag

- Do not modify the steering wheel or the steering wheel cushion.

- Do not cover the steering wheel cushion.

- Do not attach any objects (badge, logo, clock, telephone holder, etc.) to the steering wheel cushion.

- The steering wheel must not be removed (except by qualified personnel from the RENAULT Network).

- When driving, do not sit too close to the steering wheel. Sit with your arms slightly bent (see the information on

Adjusting your driving position in Section 1). This will allow sufficient space for the airbag to deploy correctly and be

fully effective.

Warnings concerning the passenger airbag

- Do not attach or glue any objects (badge, clock, telephone holder, etc.) to the dashboard in the proximity of the airbag

housing.

- Nothing should be placed between the dashboard and the passenger (pet, umbrella, walking stick, parcels, etc.).

- The passenger must not put his or her feet on the dashboard or seat as there is a risk that serious injuries may be

sustained. As a general rule, keep all parts of your body (knees, hands, head, etc.) well away from the dashboard.

- The passenger airbags should be reactivated as soon as the child seat is removed, to ensure the protection of the front

passenger in the event of an impact.

A REAR-FACING CHILD/BABY SEAT MUST NOT BE FITTED TO THE FRONT PASSENGER SEAT UNLESS THE

ADDITIONAL RESTRAINT SYSTEMS, I.E. THE PASSENGER AIRBAG, ARE DEACTIVATED.

(Refer to the information on Deactivation of passenger airbags in Section 1).

1.30

MEANS OF RESTRAINT IN ADDITION TO THE REAR SEAT BELTS

Depending on the vehicle, these

Load limiter

- After an accident, have

the entire restraint system

checked

include:

Above a certain severity of impact,

this mechanism is used to limit the

force of the belt against the body so

that it is at an acceptable level.

- seat belt pretensioners integrated

into the inertia reels (for the rear

second row seats)

- No operation whatsoever is

permitted on any part of the

system (pretensioners, airbags,

computers, wiring) and the

system components must not be

reused on any other vehicle, even

if identical.

- Force limiter.

These systems are designed to act

independently or together when the

vehicle is subjected to a frontal

impact.

There

are

two

possibilities,

- To avoid premature triggering of

the system which may cause

injury, only qualified RENAULT

Network personnel may work on

the pretensioner and airbag

system.

depending on the force of the

impact:

- protection is provided by the belt

only,

- the pretensioner is triggered to

take up the slack in the seat belt

and the airbag inflates to cushion

the impact.

- Testing of the electric trigger

system may only be carried out

by a specially trained technician

using special equipment.

Rear seat belt pretensioners

This system is only operational

when the ignition is switched on.

- When the vehicle is scrapped,

contact your RENAULT Dealer

for disposal of the pretensioner

and airbag gas generators.

If the vehicle is subjected to a severe

frontal impact, a device retracts the

seat belt, pulling the seat belt tight

against the body and thus

improving its effectiveness.

1.31

SIDE PROTECTION DEVICES

Side airbags

This airbag is fitted to each of the

front seats and is inflated at the

sides of the seats (door side) to

protect the occupants in the event of

a severe side impact.

Curtain airbags

These are airbags fitted along the

sides of the vehicle in the ceiling

which trigger along the front and

rear side windows to protect the

passengers in case of a severe side

impact.

Warnings concerning the side airbag

- Fitting seat covers: seats equipped with an airbag require covers

specifically designed for your vehicle. Contact your RENAULT

Dealer to find out if these covers may be purchased from RENAULT

outlets. The use of any covers other than those designed for your vehicle

(and including those designed for another vehicle) may affect the operation

of the airbags and reduce your protection.

- Do not place any accessories, objects or even pets between the seatback, the

door and the internal fittings. Do not cover the seatback with any items

such as clothes or accessories. This may prevent the airbag from operating

correctly or cause injury when the airbag is deployed.

- No work or modification whatsoever may be carried out on the seat or

internal fittings, except by qualified RENAULT Network personnel.

- These airbags operate through slits in the front seatbacks (door side): never

insert any objects in these slits.

A marking on the windscreen

informs you of the presence of

additional means of restraint

(airbags, pretensioners, etc.) in

the passenger compartment.

1.32

ADDITIONAL MEANS OF RESTRAINT

All the warnings below are given so that, if the airbag is activated, it is not obstructed in any way and also to prevent the

risk of serious injuries caused by items which may be dislodged when the airbag inflates.

The airbag is designed to complement the action of the seat belt. Both the airbags and seat belts are integral parts

of the same protection system. It is therefore essential to wear a seat belt at all times. If seat belts are not worn,

the occupants are exposed to the risk of serious injury in the event of an accident. It may also increase the risk of

minor superficial injuries occurring when the airbag is deployed, although such minor injuries are always

possible with airbags.

If the vehicle should overturn or suffer a rear impact, however severe, the pretensioners and airbags are not always

triggered. Shocks to the underbody of the vehicle, from pavements, potholes, stones etc. can all trigger these systems.

- No work or modification whatsoever may be carried out on any part of the airbag system (airbags, pretensioners,

computer, wiring harness, etc.), except by qualified RENAULT Network personnel.

- To ensure that the system is in good working order and to avoid accidental triggering of the system which may cause

injury, only qualified RENAULT Network personnel may work on the airbag system.

- As a safety precaution, have the airbag system checked if your vehicle has been involved in an accident, or is stolen or

broken into.

- When selling or lending the vehicle, inform the user of these points and hand over this handbook with the vehicle.

- When scrapping your vehicle, contact your RENAULT Dealer for disposal of the gas generator(s).

1.33

CHILD SAFETY

In all countries there are regulations

governing the use of restraints for

children and babies.

Some passenger seats are not

suitable for the installation of child

seats.

Remember that

a

collision at

31 mph (50 km/h) is the same as

falling a distance of 10 metres.

In Europe children under 10 years

of age⁽¹⁾must be seated in an

approved safety device which is

suitable for the weight and size of

the child.

To find the authorised seats and

types of child seats that can be

installed in each of the authorised

seats, refer to the table in the

following pages.

Expressed

transporting

in

a

other

child without

terms,

a

restraint is the equivalent of

allowing him or her to play on a

fourth-floor

railings.

balcony

without

The driver is responsible for

ensuring that this equipment is

used correctly.

Before installing a child seat in the

front seat (if installation is

permitted)

If fitted to the passenger seat, carry

out the following adjustments:

- move the passenger seat as far

back as possible,

- set the seatback to its fully upright

position,

- raise the seat squab as far as

possible,

- raise the headrest to its highest

setting,

- move the seat belt height control

to the low position.

Child restraints for which type

approval was obtained after January

1992 offer a level of safety much

greater than for restraints with type

approval before that date.

Under no circumstances

should babies or children

be allowed to travel sitting

on the knees of another

It is therefore advisable to select a

child restraint that complies with

European regulation ECE 44.

passenger in the vehicle.

Restraints that comply with this

legislation must be marked with an

orange label bearing the letter E

If a frontal impact occurs at 30 mph

(50 km/h) a child weighing 30 kg

will be transformed into a missile

equivalent to one tonne: you will

find it impossible to hold the child,

even if you yourself are wearing a

belt.

followed by

a

number (which

stands for the country where it is

type approved) and the year in

which the type approval was

granted.

It is particularly dangerous to put

the belt round your child when he

or she is sitting on your lap. Never

use the belt for more than one

person at the same time.

Refer to the Child safety equipment

booklet available from the Renault

Network to choose the seat suited to

your child and recommended for

your vehicle.

(1) You must always comply with the

laws of the country in which you are

travelling. They may be different to

the guidelines in this handbook.

1.34

CHILD SAFETY (continued)

Refer to the Child safety equipment booklet available from the RENAULT Network to choose the seat

suited to your child and recommended for your vehicle.

Seats suitable for installing a child seat

Long chassis

Standard chassis

Age of the child

(weight of the child)

Front passenger

Rear side

seats (4) (6)

Rear centre

seat (4)

Second row rear

seats

seat (1) (3)

Birth to approximately 9 months

(weight below 13 kg)

L2 - I

L2

U - I

U

X

From 9 months to 3 years approximately

(weight from 9 kg to 18 kg)

From 3 to approximately 12 years (2)

X

L1 (5)

(weight from 15 kg to 36 kg)

(1) DANGER! RISK OF DEATH OR SERIOUS INJURY: CHECK THAT THE FRONT PASSENGER AIRBAG

HAS BEEN DEACTIVATED BEFORE INSTALLING A REAR-FACING CHILD SEAT IN THIS SEAT.

1.35

CHILD SAFETY (continued)

X : seat not suitable for fitting a child seat for this age range.

U : seat suitable for fitting a belt-fitted child seat approved as “Universal” for this age range; check that it can be

fitted.

I

: seat equipped with anchoring points for mounting a seat for this age range using Isofix locks. Only RENAULT

seats are approved.

L1 : seat can only be fitted with a special RENAULT booster cushion; use the seat base only without the seatback.

L2 : Only a RENAULT approved rear-facing child seat may be installed in this seat. Please contact your RENAULT

Dealer

(2) Above a height of 1.36 m or a weight of 36 kg, a child may be strapped directly into the seat like an adult.

(3) Only a rear-facing child seat may be fitted to this seat.

(4) Place the back of the child seat against the vehicle seatback, adjust the headrest height or remove it if necessary.

(5) Both seats located in front of the seat in question must be moved fully forward.

(6) Never use the ISOFIX rear side seats without the centre seat.

1.36

CHILD SAFETY (continued)

The right choice

The safety of your children is also

your responsibility.

To ensure that your child has the

maximum possible protection, we

recommend that you use seats

approved by the RENAULT

Network.

It is preferable to use an ISOFIX seat if

your vehicle is fitted with an ISOFIX

system (refer to “ISOFIX child seat

fitting system” in Section 1).

Restraint systems for all the categories

are available. These systems have

been developed in consultation with

the manufacturers and have been

tested in RENAULT vehicles.

1

2

Categories 0 and 0+ (from 0 to

13 kg)

A child's neck is very susceptible to

injury up to the age of two. It is

preferable to put your child into a

rear facing enclosing shell seat. This

position enhances safety.

Category 1 (from 9 to 18 kg)

Between the ages of 2 and 4, a

child's pelvis is not fully developed.

Restraints using the vehicle's

three-point belts are not adequate

and there is also a risk that the child

will sustain abdominal injuries in

the event of a frontal impact. It is

therefore fitting to use an enclosing

seat for maintaining the child by

Contact your RENAULT Dealer and

ask him to help you install it.

means of

a

harness or shock

absorbing pad.

To avoid any risk to your safety, we recommend that you use

RENAULT approved accessories because they are suitable for your

vehicle and are the only accessories for which RENAULT will

provide a warranty.

1.37

CHILD SAFETY (continued)

A

booster

seat

with

a

height-adjustable seatback and a

belt guide are recommended as this

will allow the belt to be worn as

close to the base of the neck as

possible but not on it.

Place the headrest in the top

position to allow you to press the

seatback of the child seat firmly

against the vehicle seatback.

Vehicles with integrated child head

restraint: refer to the information

under “Child head restraints” in

Section 3.

If a booster seat without a seatback

is used, the vehicle's headrest will

have to be adjusted to suit the

child's stature; the upper edge of the

headrest must be at the same height

as the top of the child's head and

should never be lower than in line

with the child's eyes.

3

Category 2 (15 to 25 kg) and

category 3 (22 to 36 kg)

For correctly maintaining the pelvis

of a child under 10 years, a height

under 1.36 m and a weight of less

than 36 kg, preferably use a raised

seat with belt guides that ensure

that the three-point belt goes flat

over the child's thighs.

The standard classifies child

restraints in five categories:

Category 0 : 0 to 10 kg

Category 0+: 0 to 13 kg

Category 1 : 9 to 18 kg

Category 2 : 15 to 25 kg

Category 3 : 22 to 36 kg

1.38

CHILD SAFETY (continued)

ISOFIX child seat mounting

Useof thisdeviceonthefront

passenger seat is only

permitted if the passenger

system

To find out which seats are fitted

with this system, refer to the

information on “Seats suitable for

fitting child seats” at the beginning

of the information on “Child

safety”.

airbags

have

been

deactivated.

Refer to “Deactivation of front

passenger airbags”.

The system comprises:

- two anchoring rings located

between the base and the seatback

to attach the base of the child seat,

- a ring located under the cushion to

attach the child seat seatback in

the rear-facing position,

- a ring behind the seatback to

attach the child seatback in the

front-facing position (rear seats

only),

- a special RENAULT child seat

fitted with two locks that hook

onto the two rings and a belt to

attach the child seat seatback.

- Make sure that there is

nothing obstructing the

seat mounting mechanism

at

the

anchorage

points (gravel, rags, toys, etc.).

- Always remember to fasten

children into their seats for all

journeys.

Only special RENAULT seats are

approved for this vehicle. To

purchase these seats, please

contact your RENAULT Dealer.

1.39

CHILD SAFETY (continued)

Installation

Rear-facing Isofix seat

When a rear-facing child seat is

fitted, the seatback should be close

to or touching:

- the dashboard (in the front seat),

- the front seatback (in the rear seat).

Fitting a child seat (continued)

- Slide the seat catches 3 into the

guides 2 and push the seat firmly

to lock it on the rings,

1

- Check that the seat is locked

correctly by moving it from left to

right and then forwards and

backwards,

2

3

Forward-facing ISOFIX seat (rear

- Push firmly on the base of the seat

to press the child seat arch against

the vehicle seatback.

seats only)

When a front-facing child seat is

installed, the front seat must not be

moved back beyond the halfway

point on the seat runners and the

seatback must be in an upright

position.

Fitting a child seat

- Before fitting and using the seat,

read the instructions provided

carefully,

- Attach mounting guides

2

(supplied with the child seat or

sold separately), to rings 1 fitted to

the seat.

1.40

CHILD SAFETY (continued)

4

6

5

7

8

A rear-facing ISOFIX seat fitted on

the front passenger seat

Rear-facing seat mounting ring for

rear seats

Forward-facing seat mounting ring

(rear seats only)

The front passenger seat must be

adjusted so that the back of the child

seat is touching the dashboard.

If the seat is fitted with a support

arm 6 secured to the floor, it is

advisable to position it on the floor

flap cover: if possible, open the

cover and position the support arm

at the bottom of the storage

compartment.

- pass strap 4 (supplied with the

seat) between the two rear

headrest rods,

- attach hook 7 to the ring located

under the boot mat.

Use belt 4 supplied with the seat:

- attach the strap hook to ring 5

located under the seat on the gear

lever side,

- tighten the belt.

- attach belt hook 7 to strap on

ring 8.

- tighten the belt.

1.41

CHILD SAFETY (continued)

CHILD SAFETY

- No modifications may be made to the original component parts of the restraint system (belts and seats and

their mountings) fitted.

- Carefully follow the instructions for fitting provided by the manufacturer of the restraint system.

- Always avoid dressing the child in bulky garments and do not place any objects between the child and the restraint

system.

- The seat belt in the vehicle must be tight enough so that the child's seat is held in position securely. Check the tension

regularly.

- Never wear the belt under your arm or behind your back.

- The harness or belt should be taut and fitted to suit the child's size.

- Never allow your child to stand up or kneel on the seats while the vehicle is moving.

- Check that the child is in the correct position for the entire journey, particularly when they are asleep.

- Use the seat belts to hold the seat in position, even if it is not occupied. Otherwise, if an accident were to occur, it may

become dislodged and pose a risk to other vehicle occupants.

- Following a serious accident, check the seat belts or the ISOFIX seat mounting and replace the child seat.

- Never leave a child unsupervised in a vehicle, even if they are in a restraining device.

- Activate the rear door locks (if your vehicle is equipped with these).

- Make sure the child does not get out of the vehicle at the side where there is traffic.

- Set your children a good example - always wear your seat belt.

1.42

CHILD SAFETY (continued)

9

DANGER

Since

front

passenger

airbag triggering and the

position of a rear-facing

child seat are incompatible, it is

not permitted to install such a seat

in this position unless the vehicle

is fitted with an airbag deactivation

device. The child may suffer very

serious injuries if the airbag

inflates.

10

Deactivating the front passenger

airbags (if fitted)

In order to fit a rear-facing child seat

on the front passenger seat, you

must deactivate the front passenger

seat additional restraint equipment

(front and lateral airbags and lap

belt pretensioners).

To deactivate the airbags: when

the vehicle is stationary, push and

turn lock 9 to the OFF position.

The label (on the dashboard) and

the markings (on the sun visor)

remind you of these instructions.

With the ignition switched on, you

must check that warning light 10,

AIRBAG OFF on the dashboard is

lit up.

This light remains continuously

lit to let you know that you can fit

a child seat.

1.43

CHILD SAFETY (continued)

9

10

Operating faults

Activating the front passenger

airbags

It is forbidden to fit a rear-facing

child seat on the front passenger

seat if the airbag activation/

deactivation system is faulty.

The passenger airbag must

only be deactivated or

activated when the vehicle

is stationary.

You should reactivate the airbag as

soon as you remove the child seat

from the front passenger seat to

ensure the protection of the front

passenger in the event of an

impact.

We do not recommend fitting any

other kind of passenger seat device.

If the lock is moved when the

vehicle is moving, warning lights

Contact your RENAULT Dealer as

soon as possible.

ú

å

and

come on: the

Reactivating airbags: when the

vehicle is stationary, push and

turn the lock 9 to the ON position.

passenger airbag is deactivated.

Switch the ignition off then on

again to reset the airbag in

accordance with the lock.

Check that warning light 10

ã

is off. The means of restraint in

addition to the front passenger

seat belts are activated.

1.44

STEERING WHEEL

1

Height and depth adjustment

Pull lever 1 and place the steering

wheel in the required position;

push the lever to lock the steering

wheel in place.

Never switch off the ignition when

travelling downhill and avoid

doing so in general when driving,

as the power assisted steering and

brake servo will not function.

For safety reasons, only

adjust the steering wheel

when the vehicle is

stationary.

1.45

DRIVER’S POSITION, LEFT-HAND DRIVE

1

2

3

4

5

6

7

8 9

10 11

12

13

14

24

28

26

25

23 22

17 16

15

29

27

21

20

19 18

1.46

DRIVER’S POSITION, LEFT-HAND DRIVE (continued)

The equipment fitted, described below, depends on the version, option and country.

1

2

3

Side window demisting vent.

Side vent.

10 Centre air vents.

11 Clock,

21 Handbrake.

temperature,

radio

22 Gear lever.

information, navigation system

display, depending on vehicle.

Stalk for:

23 RENAULT Card reader.

24 Engine start/stop button.

- direction indicators,

- exterior lights,

- front fog lights,

- rear fog lights.

12 Passenger airbag location.

13 Side vent.

4

Location for driver's airbag,

horn.

25 Control for adjusting steering

14 Side window demisting outlet.

15 Glovebox.

wheel height and reach.

5

6

7

Driver's storage compartment.

Radio remote control.

26 Bonnet release.

16 Location for radio, navigation

system etc.

27 Cruise control/speed limiter

controls.

17 Central door locking switch

18 Hazard warning lights switch.

19 Cigarette lighter.

- Stalk for windscreen and rear

screen wash/wipe.

- Trip computer and warning

system scroll control.

28 Controls for:

- electric

headlight

beam

adjustment,

- dimmer for control lighting,

- ASR traction control.

8

9

Instrument panel.

20 Location of ashtray or cup

Air conditioning controls.

holder.

29 Parking brake.

1.47

DRIVER’S POSITION, RIGHT-HAND DRIVE

1

2

3

4

5

6

7

8 9

10 11

12 13 14 15

29 28 27 26 25

21 20 19

18

17 16

24

23

22

1.48

DRIVER’S POSITION, RIGHT-HAND DRIVE (continued)

The equipment fitted, described below, depends on the version, option and country.

1

2

3

4

5

6

Side window demisting vent.

Side vent.

11 Driver's airbag and horn

20 RENAULT Card reader.

21 Gear lever.

location.

12 Radio remote control.

Passenger airbag location.

Instrument panel.

22 Handbrake.

13 - Stalk for windscreen and rear

screen wash/wipe.

- Trip computer and warning

system scroll control.

23 Location of ashtray or cup

Centre air vents.

holder.

14 Side vent.

Heater/air

controls

conditioning

24 Cigarette lighter.

15 Side window demisting outlet.

16 Parking brake.

7

8

Clock,

temperature,

radio

information, navigation system

display, etc. depending on

vehicle.

25 Hazard warning lights switch.

26 Electric door locking controls.

17 Controls for:

Stalk for:

- electric

headlight

beam

- direction indicators,

- exterior lights,

- front fog lights,

- rear fog lights.

adjustment,

- dimmer for control lighting,

- ASR traction control.

27 Location for radio, navigation

system etc.

18 Control for adjusting steering

9

Cruise control/speed limiter

controls.

28 Glovebox.

wheel height and reach.

10 Driver's storage compartment.

19 Engine start/stop button.

29 Bonnet release.

1.49

INSTRUMENT PANEL: warning lights

The presence and operation of the warning and indicator lights described below depend on the vehicle

equipment and country.

A

Instrument panel A

Front fog light indicator

light

Dipped-beam

indicator light

headlight

Rear fog light indicator

light

Side light warning light

If the

warning light comes

on, you should visit a RENAULT

Dealer immediately.

Headlight main

warning light

beam

If the

warning light comes

on, you must stop as soon as traffic

conditions allow.

1.50

INSTRUMENT PANEL: warning lights (continued)

The presence and operation of the warning and indicator lights described below depend on the vehicle

equipment and country.

Warning light

This lights up when the

engine is started and goes

Electronic

Stability

Battery charge warning

light

This lights up when the

engine is started then goes out as

soon as the engine is running.

Program (ESP) and traction

control

warning light.

There are several reasons why the

warning light may come on: see the

information on the Electronic

Stability Program (ESP) and

Traction Control (ASR) in Section 2.

system

(ASR)

out after a few seconds. It may come

on with other warning lights or

messages on the instrument panel.

If it comes on when the vehicle is

being driven, and is accompanied

If it comes on when the vehicle is

being driven, it is advisable to visit

your RENAULT Dealer as soon as

possible.

by the

warning light and a

beep, it indicates that the electrical

circuit

is

overcharged

or

Oil pressure warning light

undercharged. Stop and have the

circuit checked.

It lights up when the engine

STOP warning light

It goes out as soon as the

engine starts.

is started then goes out after

a few seconds. If it comes on when

the vehicle is being driven, accom-

Handbrake or parking

brake “on” warning light

and braking system fault

warning light

It lights up at the same time as other

warning lights and/or messages,

and is accompanied by a beep.

panied by the

warning light

and a beep, it is essential to stop and

switch off the ignition. Check the oil

level. If the level is normal, this

indicates another fault. Call

RENAULT Dealer.

It indicates that it is essential to stop

immediately (as soon as traffic

conditions allow).

If it lights up when braking and is

a

accompanied by the

warning

light and a beep, this indicates that

the fluid level in the circuit is low or

that there is a braking system fault.

Stop as soon as traffic conditions

allow and call a RENAULT Dealer.

Parking

brake

fault

warning light

Refer to the information on

“Parking brake” in Section 2.

1.51

INSTRUMENT PANEL: warning lights (continued)

The presence and operation of the warning and indicator lights described below depend on the vehicle

equipment and country.

Right-hand direction

indicator light

Left-hand direction

indicator light

Driver seat belt reminder

warning light

If the driver’s seat belt is

ç

not fastened the light remains on

when the engine is started, then

when the vehicle reaches a speed

of approximately 6 mph (10 km/h),

it flashes and a beep sounds for

about 90 seconds.

Airbag warning light

Door and boot status warning

light

This lights up when the

engine is started and goes

Shows if a door or the boot

out after a few seconds.

is left open or not closed properly.

If it does not light up when the

ignition is switched on, or comes on

when the engine is running, there is

a fault in the system.

Preheating warning light

(diesel version)

é

Tyre Pressure Monitor

Refer to the Tyre Pressure

Consult your RENAULT Dealer as

soon as possible.

With the ignition switched

on, this light should come on; it

indicates that the heater plugs are

switched on. It goes out when

preheating is complete and the

engine can be started.

Monitor

Section 2.

information

in

Passenger airbag

deactivated

This warning light comes on

several seconds after the engine is

started when the front passenger

airbags (depending on vehicle) are

deactivated.

1.52

INSTRUMENT PANEL: warning lights (continued)

The presence and operation of the warning and indicator lights described below depend on the vehicle

equipment and country.

Speed limiter and cruise

control indicator light

Toxic fume filter system

warning light

See the Speed limiter and

Cruise control information in

Section 2.

For vehicles equipped with

this option, the light comes on

when the engine is started then goes

out.

- If it lights up constantly, contact

your RENAULT Dealer as soon as

possible,

Not used

- If it flashes, reduce the engine

speed until the light stops

flashing.

Anti-lock braking system

warning light (ABS).

This lights up when the

ignition is switched on and then

goes out. If it comes on when you

are driving, it indicates a fault in the

Anti-lock Braking System.

Consult your RENAULT Dealer as

soon as possible.

Refer to the information on

emission control, fuel economy and

driving in Section 2.

Braking will then be as normal,

without the ABS system.

Contact your RENAULT Dealer as

soon as possible.

1.53

INSTRUMENT PANEL: displays and indicators

2

1

3

4

5

Rev counter 1

Instrument panel in miles:

To return to the previous mode,

carry out the same operation.

it is possible to switch to km/h.

(graduations × 1000)

The red numbers indicate forbidden

engine speeds.

- with the ignition off, press button

Note: once the battery is switched

off, the trip computer automatically

returns to the original unit.

3 or 4 and starter button 5.

- the speed measurement unit

indicator

flashes

for

Speedometer 2

In kilometres or miles per hour.

approximately three seconds, then

the new unit is displayed: release

button 3 or 5.

Overspeed buzzer

Depending on the vehicle,

a

buzzer sounds for approximately

10 seconds every 40 seconds, as

long as the vehicle is travelling in

excess of 75 mph (120 km/h).

1.54

INSTRUMENT PANEL: displays and indicators (continued)

8

6a

7

6

Coolant temperature indicator 6

Fuel level gauge 7

Information display 8

In normal use, the level must be

The number of lit squares shows the

Depending on the vehicle, it

below zone 6a. Under severe

remaining fuel level.

includes:

conditions

the

needle

may

- the time,

- the external temperature,

- radio signals,

When it is at minimum, the bottom

square lights up and flashes. Then a

beep will be heard: refill as soon as

possible.

approach this zone. But the

situation

is

not

serious

unless the

warning light

- navigation aid information.

lights up, accompanied by

a

message on the instrument panel, a

beep and warning light 6a.

1.55

TRIP COMPUTER AND WARNING SYSTEM

c) mileage before service,

d) programmed speed

limiter/cruise control),

(speed

e) computer log:

information

a

record of

3

messages and

1

operating fault messages stored

by the computer.

4

Trip computer and warning

system

The following are given on the

instrument panel display 1:

- information messages (journey

parameters etc.),

- the operating fault messages

Display selection keys 3 and 4

Scroll through the following

information in order or reverse

order by briefly pressing the key

repeatedly.

a) total mileage and trip mileage

recorder,

b) journey parameters (depending

on vehicle):

(generally linked to the

warning light),

- warning messages (linked to the

- fuel used,

- average fuel consumption,

- current fuel consumption,

- estimated range,

warning light).

- distance travelled,

- average speed,

1.56

TRIP COMPUTER AND WARNING SYSTEM (continued)

Interpreting some of the values

- You may also notice that the

average

fuel

consumption

displayed after resetting

increases when the vehicle is

stationary and the engine idling.

The values showing average fuel

consumption, range and average

3

speed will become more stable and

reliable the further you travel since

the last time the reset key was

pressed.

This is normal, since the

computer takes account of fuel

used during idling.

For the first few miles after pressing

the reset key you may notice:

Automatic resetting of the

journey parameters

Resetting occurs automatically

when the maximum value of any

of the parameters is exceeded.

- That the range increases as you

travel.

This is normal; average fuel

consumption may decrease when:

4

- the vehicle stops accelerating,

- the engine reaches its operating

temperature (engine cold when

reset key pressed),

- when you enter an urban area

after driving on the open road.

Trip mileage reset buttons 3and 4

To reset the trip mileage recorder,

select the trip mileage display, then

press key 3 or 4 until the recorder is

reset.

Journey parameter reset buttons

3 and 4

With one of the trip parameters

selected on the display, press button

3 or 4 until the display resets.

1.57

TRIP COMPUTER AND WARNING SYSTEM (continued)

Journey parameters

The display on the instrument panel of the information described below depends on the vehicle equipment and

country.

Interpreting the display selected

Examples of selections

24050

a) Total mileage and trip mileage recorders.

24051

b) Journey parameters.

OR

Fuel consumed since the last reset.

Average fuel consumption since the last reset.

This value is displayed after driving 400 metres and takes into account the

distance travelled and the fuel used since the last time the reset button was

pressed.

1.58

TRIP COMPUTER AND WARNING SYSTEM (continued)

Journey parameters

The display on the instrument panel of the information described below depends on the vehicle equipment and

country.

Examples of selections

Interpreting the display selected

Current fuel consumption

24054

This value is displayed after reaching a speed of approximately 15 mph

(30 km/h).

Estimated range with remaining fuel

24055

This range takes into account the average fuel consumption since the last

time the reset button was pressed.

The value is displayed after driving 400 metres.

Distance travelled since last reset.

Average speed since the last reset.

The value is displayed after driving 400 metres.

1.59

TRIP COMPUTER AND WARNING SYSTEM (continued)

Journey parameters

The display on the instrument panel of the information described below depends on the vehicle equipment and

country.

Examples of selections

Interpreting the display selected

c) Mileage before oil change/service

(Displayed as the oil change mileage approaches.)

Distance left before the next service.

There are several scenarios:

24058

- range less than 900 miles (1,500 km) or next service recommended

within two months. The “SERVICE! CHANGE OIL” message is displayed

Ê

along with the

symbol (as long as “mileage before service” is displayed,

or for 15 seconds).

- mileage before service equal to 0 miles/km or date of service reached.

Ê

The “SERVICE! CHANGE OIL” message is displayed along with the

symbol flashing when the “mileage before service” display is selected.

Resetting the display after service in accordance with the maintenance

program

The mileage before oil change/service must only be reset after a service

complying with the recommendations in the Warranty and Servicing

booklet. If you decide to change the oil more frequently, do not reset this

data each time the oil is changed. This prevents the replacement interval

from being exceeded for other parts included in the maintenance

program.

To reset the mileage before oil change/service, press and hold one of the

display reset buttons for approximately 10 seconds until the display

shows the mileage permanently.

1.60

TRIP COMPUTER AND WARNING SYSTEM (continued)

Journey parameters

The display on the instrument panel of the information described below depends on the vehicle equipment and

country.

Examples of selections

Interpreting the display selected

d) Cruise control/speed limiter speed setting (depending on vehicle)

24060

See “Speed Limiter” and “Cruise Control” in Section 2.

24061

e) On-board log

Successive display:

- of information messages (heated seats, automatic headlights, etc.

depending on the vehicle),

- of operating fault messages (check the injection system, etc.).

1.61

TRIP COMPUTER AND WARNING SYSTEM (continued)

Information messages

These can help either in the vehicle starting phase, or give information about a selection or a driving status.

Examples of information messages are given in the following pages.

Messages

Interpretation of messages

Indicates that the automatic lights function is deactivated.

"Automatic lights OFF"

Request to insert the RENAULT card into the reader.

"Insert card"

Minimum engine oil level warning: the display informs the driver that the engine oil

level is low when the engine is started. This warning lasts for 30 seconds. Refer to the

information on Engine oil level in Section 4.

"Oil level OK"

1.62

TRIP COMPUTER AND WARNING SYSTEM (continued)

Operating fault messages

You should immediately go to your RENAULT Dealer for work to be carried out on your vehicle. These messages

appear accompanied by the

warning light. They disappear when the display selection key is pressed or after

ú

several seconds and are stored in the computer log. The

are given in the following pages.

warning light remains lit. Examples of fault messages

ú

Messages

Interpretation of messages

ASR Traction Control system deactivated (see the information on ASR Traction

Control in Section 2).

"ASR deactivated"

"Check gearbox"

Indicates that a fault has occurred in the gearbox; contact your RENAULT Dealer as

soon as possible.

Sensor fault on the wheel not shown on the instrument panel: this is the case, for

example, when the emergency spare wheel is fitted on the vehicle (see the

information on Tyre pressure monitor in Section 2).

"Tyre sensor fault"

"Card not detected"

The hands-free RENAULT card is not in the detection zone, or the vehicle has not

been able to detect it. Insert it in the reader, if the fault persists contact your

RENAULT Dealer.

1.63

TRIP COMPUTER AND WARNING SYSTEM (continued)

Operating fault messages (continued)

You should immediately go to your RENAULT Dealer for work to be carried out on your vehicle. These messages

appear accompanied by the

warning light. They disappear when the display selection key is pressed or after

ú

several seconds and are stored in the computer log. The

are given in the following pages.

warning light remains lit. Examples of fault messages

ú

Messages

Interpretation of messages

Indicates that there is water present in the diesel fuel. Contact your RENAULT Dealer

as soon as possible.

"Check diesel filter"

"Change card battery"

"Check tyre pressure"

Your RENAULT card battery has a service life of approximately two years.

This message appears when the battery begins to run flat (refer to RENAULT Card:

batteries in Section 5).

Tyre pressure fault (under-inflation) shown on the multifunction display or on the

instrument panel; correct the tyre pressure as soon as possible.

1.64

TRIP COMPUTER AND WARNING SYSTEM (continued)

Warning messages

These warn you to stop immediately (as soon as traffic conditions allow) and to call a RENAULT Dealer. These

messages appear accompanied by the

pages.

warning light. Examples of warning messages are given in the following

û

NB: the messages appear on the display either individually or alternately (when there are several messages to be

displayed), and may be accompanied by a warning light and/or a beep.

Messages

Interpretation of messages

Indicates a puncture in the tyre shown on the tyre pressure monitor display.

Indicates a fault with the vehicle’s electronic management system.

Indicates a fault with the battery charging circuit.

"Stop! Tyre puncture"

"Electronic fault"

"Battery charging fault"

"Steering fault"

Indicates a fault in the vehicle’s power-assisted steering.

1.65

TRIP COMPUTER AND WARNING SYSTEM (continued)

Warning messages

These warn you to stop immediately (as soon as traffic conditions allow) and to call a RENAULT Dealer. These

messages appear accompanied by the

pages.

warning light. Examples of warning messages are given in the following

û

NB: the messages appear on the display either individually or alternately (when there are several messages to be

displayed), and may be accompanied by a warning light and/or a beep.

Interpretation of messages

Messages

Indicates a parking brake fault.

"Parking brake fault"

"Braking fault"

Indicates a fault in the braking circuit.

Indicates that the vehicle has a serious engine fault.

Indicates an oil pressure fault.

"Injection fault"

"Oil pressure fault"

"Engine overheating"

Indicates that the engine is overheating.

1.66

CLOCK AND EXTERIOR TEMPERATURE

Vehicle without button 2 (vehicles

Exterior temperature indicator

Special note:

When the external temperature is

between –3°C and +3°C, the °C

figures flash (indicates risk of ice

formation).

equipped with a navigation system,

audio equipment, etc.)

1

Refer to the equipment instructions

for the special features of these

vehicles.

2

When the ignition is switched on,

the clock and (depending on

vehicle) external temperature are

displayed.

Setting the time on the clock 1

Vehicle with button 2

Exterior

temperature

If the electrical supply is cut

(battery disconnected, feed wire

broken, etc.), the clock will not

display the correct time.

indicator

- press and hold button

2

for

As black ice formation is

related to exposure,

humidity and temperature, the

exterior temperature alone is not

sufficient to detect black ice.

approximately three seconds,

- when the hour flashes, press

button 2 again to adjust it,

The clock must be reset.

- wait approximately three seconds,

the minutes will flash, press

button 2 to adjust them,

- wait approximately three seconds,

the minutes stop flashing, the time

is set.

We recommend that you do not

make these settings while

driving.

1.67

DOOR MIRRORS

Folding door mirrors

Move button 1 to position D: the

door mirrors fold in.

To reset them to driving position,

return to position A, B or C.

F

E

A

B

De-icing door mirrors

The door mirrors are heated in order

to de-ice them when rear screen

demisting is switched on.

D

1

C

Electric door mirrors

With the engine running, turn

knob 1:

The driver's door mirror

may have two clearly

- position A to adjust the left-hand

door mirror;

defined zones. Zone

F

shows what can normally

be seen in an ordinary door mirror.

For your safety, zone E increases

the area you can see at the rear and

to the side of your vehicle.

- position C to adjust the right-

hand door mirror;

B is the central neutral position.

Objects in zone A look much

further away than they really are.

1.68

REAR-VIEW MIRRORS

3

2

Interior rear-view mirror

Electrochrome rear-view mirror 3

This is adjustable. Pull down small

lever 2 located behind the rear view

mirror when driving at night to

avoid being dazzled by the

headlights of the car behind.

The rear view mirror darkens

automatically at night when you are

followed by a vehicle with its

headlights

on

(main

beam

headlights).

1.69

WARNING LIGHTS AND BUZZERS

Hazard warning lights

(continued)

Depending on the vehicle, the

hazard warning lights may come on

automatically under deliberate

heavy deceleration.

In this case, the hazard warning

lights may be switched off by

pressing switch 2 once.

1

0

A

2

Direction indicators

Move stalk 1 parallel to the steering

wheel and in the direction you are

going to turn.

In motorway driving, steering

wheel movements are normally

insufficient to automatically return

the stalk to the 0 position. There is

an intermediate position in which

the stalk may be held when

changing lanes.

Horn

Hazard warning lights

Press switch 2.

This switch lights all four direction

indicators and the side-mounted

indicators simultaneously.

Press steering wheel cushion A.

Headlight flasher

Pull stalk 1 towards you to flash the

headlights, even if the lights are not

in use.

Only use this function to warn other

road users if you:

- are obliged to stop for any reason

beyond your control in an unusual

or prohibited location,

When you release the stalk, it

automatically returns to position 0.

- are obliged to drive under special

conditions.

1.70

EXTERIOR LIGHTING AND SIGNALS

Automatic operation (depending

on vehicle)

With the engine running, the

dipped beam headlights switch

themselves on or off automatically

depending on exterior brightness,

without the need to operate stalk 1

(position 0).

1

4

3

1

This function can be deactivated or

reactivated.

- To activate it, press button 3 for at

least four seconds. Two beeps and

the “Automatic lighting ON”

message confirm this action.

2

- To deactivate it, with the vehicle

stationary, press button 3 for at

least four seconds.

A

beep

Switching on the side

lights

Turn the end of stalk 1 until the

symbol faces mark 4.

Switching on the dipped

beam headlights

Manual operation

Turn the end of stalk 1 until the

symbol faces mark 4.

confirms this action and the

message “Automatic lighting

OFF” appears on the instrument

panel.

The instrument panel lights up and

the brightness can be adjusted using

wheel 2.

If stalk 1 is operated, it overrides

A warning light on the instrument

panel will light up.

and

cancels

the

operation

temporarily.

A warning light on the instrument

panel will light up.

Before driving at night, check that the electrical equipment is operating correctly and adjust the headlight

beams (if your vehicle is not carrying its normal load). In general, check that the lights are not obscured (by

dirt, mud, snow or objects which could cover them).

1.71

EXTERIOR LIGHTING AND SIGNALS (continued)

See-me-home lighting function

Turning off the lights

Manual operation

There are two possible ways

(depending on vehicle):

This function (useful, for example,

for opening a gate, a garage, etc.),

enables you to momentarily switch

on dipped beam headlights.

1

- return stalk

position,

1

to its original

With the engine switched off and

the lights off, the end of stalk 1 in

position 0, pull stalk 1 towards you:

the dipped beam headlights light up

for approximately thirty seconds.

- the lights go out when the engine

is stopped, when the driver's door

is opened or when the vehicle is

locked. In this case, the next time

the engine is started the lights will

be switched back according to the

position of the stalk 1.

This action may be carried out no

more than four times for

a

maximum lighting period of two

minutes.

Automatic operation (depending

on vehicle)

The lights go out when the engine is

stopped, when the driver's door is

opened or when the vehicle is

locked.

To switch off the lights before they

switch off automatically, turn the

end of stalk 1, then return it to

position 0.

Switching on the main

beam headlights

With the dipped beam headlights

on, pull stalk 1 towards you.

When the main beam headlights are

lit up, an indicator light on the

instrument panel comes on.

Lights on warning buzzer

If the lights are switched on after the

engine is switched off, a warning

buzzer sounds when the driver's

door is opened to warn you that the

lights are still on.

To return to the dipped headlight

position, pull the stalk towards you

again.

1.72

EXTERIOR LIGHTING AND SIGNALS (continued)

Switching off the lights

Rear fog light

Turn ring 5 again until mark 6 is

opposite the symbol for the fog light

you wish to switch off.

The front and rear fog lights switch

off when the exterior lights are

switched off.

Turn centre ring 5 on the

1

stalk until the symbol faces mark 6,

then release it.

5

Operation of the fog lights depends

on the exterior lighting selected,

and an indicator light will light up

on the instrument panel.

Remember to switch off the rear fog

light when it is no longer needed to

avoid inconveniencing other road

users.

6

Note: the fog light is on the driver's

side.

Front fog lights

Turn centre ring 5 on the

stalk until the symbol faces mark 6,

then release it.

Operation of the fog lights depends

on the exterior lighting selected,

and an indicator light will light up

on the instrument panel.

When driving in the fog, the fog

lights are not switched on

automatically, so this remains

under the control of the driver:

the warning lights on the

instrument panel inform you

whether the fog lights are on

(warning light lit) or off (warning

light not lit).

1.73

ELECTRICAL ADJUSTMENT OF THE HEADLIGHT BEAM HEIGHTS

Examples of control Adjustment position

0

A

1

On vehicles fitted with this

function, control A allows you to

adjust the height of the beams

according to the load.

Turn control A down to lower the

1

2

4

headlights and up to raise them.

Adjustment is automatic on other

versions.

1.74

WINDSCREEN WASH / WIPE

Automatic wiper function

(depending on vehicle)

1

With the engine running, move

stalk 1.

2

1

- A Stop.

A

B

- B Automatic wiper function.

When this position is selected,

the system detects the presence

of water on the windscreen and

triggers wiping at a suitable

wiping speed.

C

D

It is possible to change the

interval between sweeps by

turning ring 2.

With the engine running or

accessories function enabled, move

stalk 1

Special note

- C Normal wiping speed.

- D Fast wiping speed.

When driving, every time the

vehicle stops the fast wiping speed

is reduced to normal wiping speed.

- A Off.

As soon as the vehicle moves off,

wipe will return to the speed

originally selected.

- B Intermittent wiping.

The wipers will pause for

several

seconds

between

If stalk 1 is operated, it overrides

and cancels automatic operation.

sweeps. It is possible to change

the time between sweeps by

turning ring 2.

- C Normal wiping speed.

- D Fast wiping speed.

If for any reason the wipers are

seized (e.g. frozen to windscreen

by ice, etc.), the system will

automatically cut the power

supply to the wipers.

1.75

WINDSCREEN WASH/WIPE (continued)

- Headlights on

1

The headlight washers will be

activated at the same time.

1

A

B

C

D

Windscreen washers, headlight

washers (depending on vehicle)

In frosty weather, make sure that

the wiper blades are not stuck by

ice (risk of motor overheating).

With the ignition on, pull stalk 1

towards you.

Keep an eye on the condition of

the blades. Replace the wiper

blades as soon as they begin to

lose efficiency (approximately

once a year).

- Headlights off

One short pull activates the

windscreen washers and one

sweep of the windscreen wipers.

A

longer pull activates the

Regularly

clean

your

Before

washing

the

windscreen washers and three

sweeps of the windscreen wipers

followed by one sweep a few

seconds later.

windscreen.

vehicle, bring the stalk to

position A (park) to avoid

the risk of damage to the

blades when automatic wiping is

activated.

If you switch off the ignition

before

switching

off

the

windscreen wiper (position A)

the blades will stop at random on

the windscreen.

1.76

REAR SCREEN WASH/WIPE

Rear screen wash/wipe

Special note

1

To activate the rear screen

washer, turn the end of stalk 1 with

the ignition on to align mark 2 with

the symbol.

The rear screen wiper sweeps

intermittently if reverse gear is

selected when the windscreen

wipers are in operation.

When the stalk is released, it returns

to the rear wipe position.

Note:

In frosty weather, make sure that the

wiper blades are not stuck by ice

(risk of motor overheating).

2

Keep an eye on the condition of the

blades. Replace the wiper blades as

soon as they begin to lose efficiency

(approximately once a year).

Regularly clean your rear screen.

Before using the rear screen wiper,

Speed-dependent timed

rear screen wiper

With the ignition on, turn the end of

stalk 1 to align it with mark 2

opposite the symbol.

check

that

nothing

being

transported on the outside of the

vehicle obstructs the movement of

the wiper.

Wiping frequency varies with

speed.

1.77

FUEL TANK

Fuel grade

Use a high grade fuel with the

appropriate octane rating as defined

by the particular standards in force

in your country.

Petrol version.

C

It is essential to use unleaded

petrol, abiding by the particular

legislation in force in each country.

The octane rating (RON) must

conform with the information given

on the label inside fuel filler flap.

Refer to Section 6 for information

on “Engine specifications”.

B

A

Diesel versions

Fuel tank capacity:

It is essential to use diesel fuel that

conforms with the information

given on the label inside fuel filler

flap A.

60 litres approximately.

To open flap A, put your finger in

recess B and pull.

The shut-off system (metal valve) C

Make

sure

that

no

water

is built into the filler pipe.

accidentally enters the fuel tank

during filling. The shut-off system

and its surrounding area must be

dust-free.

Refer to “Filling with fuel” for more

details.

Never press the metal valve

with your fingers.

Do not wash the filler area

with

washer.

a

high-pressure

Do not mix even small

amounts of petrol with

diesel.

1.78

FUEL TANK (continued)

Filling with fuel

Petrol versions

Using leaded petrol will damage the

anti-pollution devices and may lead

to a loss of warranty.

Filling with fuel (continued)

Petrol and diesel versions

No more than two filling operations

may be made after the fuel feed has

switched off automatically for the

first time because there must be

sufficient space in the fuel tank to

allow for expansion.

Persistent fuel odour

If you notice a persistent fuel odour

you should:

- stop the vehicle when traffic

conditions allow and switch off

the ignition,

To ensure that the fuel tank is not

filled with leaded petrol, the fuel

tank filler neck contains a restrictor

fitted with a foolproof system which

only allows the nozzle for unleaded

petrol to be used (at the pump).

- Insert the nozzle so that the metal

valve is pushed back and then

insert it fully before beginning to

fill the tank (risk of splash-back).

- switch on the hazard warning

lights and ask your passengers to

leave the vehicle and stay clear of

the traffic,

- Do not operate on, or restart, the

vehicle before it has been

inspected by qualified staff from

the RENAULT network.

- Keep the nozzle in this position

throughout the entire filling

operation.

No

modifications

whatsoever are permitted

on any part of the fuel

supply system (computers,

wiring, fuel circuit, injector,

protection covers, etc.) as this

may be dangerous (such work

must be undertaken by qualified

RENAULT Network personnel).

1.79

1.80

Getting to know your vehicle for Your Renault Scenic 4 Door Second Generation (2003-2009)

Related Topics

Popular Owner Manuals

Latest Owner Manuals