Get Operation -> Lights and visibility Guide for Seat Leon 4 Door Third Generation (2012-2020)

Lights and visibility

Several warning and control lamps light up

for a few seconds when the ignition is switch-

ed on, signalling that the function is being

verified. They will switch off after a few sec-

onds.

WARNING

Lights and visibility

The side lights or daytime running lights

are not bright enough to illuminate the road

ahead and to ensure that other road users

are able to see you.

Lights

Control lamps

●

Always use your dipped beam head

lights if it is raining or if visibility is poor.

WARNING

Observe the safety warnings

in Con-

›››

It lights up



trol and warning lamps on page 123.

WARNING

Driving light totally or partially faulty.

Fault in the cornering light system.

If the headlights are set too high and not

used correctly, there is a risk of dazzling or

distracting other road users. This could re-

sult in a serious accident.

Side light and dipped beam head-

light

It lights up



●

Always make sure that the headlights are

Rear fog light switched on page 146.

›››

Read the additional information carefully

^››› ^{page 32}

correctly adjusted.

It lights up



The driver is personally responsible for the

correct use and adjustment of the lights in all

situations.

Note

Left or right turn signal.

The legal requirements regarding the use

of vehicle lights in each country must be

observed.

The control lamp flashes twice as fast when a turn

signal is faulty.

Audible warnings to advise the driver that

the lights have not been switched off

Hazard warning lights on page 148.

›››

If the key is not in the ignition and the driver

door is open, an audible warning signal is

heard in the following cases: this will remind

you to turn the light off.

It lights up



Daytime running lights

Trailer turn signals

The daytime running lights consist of individu-

al lights, integrated in the front headlights.

With the daylight driving lights on, only these

It lights up



●

When the parking light is on page 144.

›››

Main beam on or flasher on page 144.

›››

lights switch on

.

›››

●

When the light switch is in position  or .

The daytime running lights switch on every

time the ignition is switched on, if the switch is

It lights up



»

The Light Assist system is on page 145.

›››

143

Operation

in positions  or , according to the level of

Convenience turn signals

Note

exterior lighting.

For the one-touch signalling, when the igni-

tion is switched on, move the lever as far as

possible upwards or downwards and release

the lever. The turn signal will flash three times.

●

If the convenience turn signals are oper-

When the light switch is in position , a light

sensor automatically switches dipped beam

on and off (including the control and instru-

ment lighting) or the daytime running lights

depending on the level of exterior lighting.

ating (three flashes) and the other conven-

ience turn signals are switched on, the ac-

tive part stops flashing and only flashes

once in the new part selected.

One-touch signalling is activated and deacti-

vated in the Easy Connect system via the  /

 button and the function button Vehicle

> SETTINGS > Lights > One-touch sig-

●

The turn signal only works when the igni-

tion is switched on. The hazard warning

lights also work when the ignition is switch-

ed off.

WARNING

●

Never drive with daytime lights if the road

nalling

^››› ^{page 35.}

●

If a trailer turn signal malfunctions, the

is not well lit due to weather or lighting

conditions. Daytime lights do not provide

enough light to illuminate the road properly

or be seen by other road users.

In vehicles that do not have the correspond-

ing menu, this function can be deactivated in

a specialised workshop.

control lamp will stop flashing (trailer turn

signals) and the vehicle turn signal will

flash at double speed.

●

The main beam headlights can only be

On vehicles with rear lights with bulbs,

WARNING

switched on if the dipped beam headlights

are already on.

when activating the daytime running light

the rear lights are not switched on. A vehi-

cle which does not have the rear lights on

may not be visible to other drivers in the

darkness, in the case of heavy rain or in

conditions of poor visibility.

Improper or lack of use of the turn signals,

or forgetting to deactivate them can con-

fuse other road users. This could result in a

serious accident.

●

In cold or damp weather conditions, the

headlights, tail lights and turn signals may

mist up inside temporarily. This is normal

and in no way effects the useful life of the

vehicle lighting system.

●

Always give warning when you are going

to change lane, overtake or when turning,

activating the turn signal in good time.

●

As soon as you have finished changing

Turn signal and main beam lever

lane, overtaking or turning, switch the turn

signal off.

Automatic dipped beam control

*

Read the additional information carefully

^››› ^{page 33}

WARNING

Incorrect use of the headlights may cause

accidents and serious injury, as the main

beam may distract or dazzle other drivers.

The automatic dipped beam control is merely

intended as an aid and is not able to recog-

nise all driving situations.

Push the lever all the way down to turn off the

corresponding function.

When the light switch is in position , the

vehicle lights and the instrument panel and

144

Lights and visibility

switch lighting switch on and off automatical-

ly in the following situations in Daytime

When the system is activated and the cam-

era detects other vehicles that may be daz-

zled, the main beam is automatically switch-

ed off. Otherwise, the main beam is automati-

cally switched on.

the headlights in time or from turning off alto-

gether:

›››

running lights on page 144:

●

In poorly lit towns with highly reflective

signs.

Automatic switch-

ing on

Automatic switch-

ing off

●

Other insufficiently lit road users (such as

The main beam assist generally detects illu-

minated areas and deactivates the main

beam when passing through a town, for ex-

ample.

pedestrians or cyclists).

The photo sensor de-

When adequate lighting

●

On tight bends and steep slopes (bumps)

tects darkness, for exam- is detected.

ple, when driving through

a tunnel.

and when oncoming vehicles are partially

obscured.

Switching the main beam assist on and off

●

When the drivers of other oncoming vehi-

The rain sensor detects

rain and activates the

windscreen wipers.

When the windscreen

wipers have been inac-

tive for a few minutes.

cles (such as a truck) can see over a guard

rail in the centre of the road.

Func-

tion

Use

●

If the camera is damaged or the power

WARNING

If the road is not well lit and other road

users cannot see the vehicle well enough

or at all, accidents may occur.

– Switch the ignition on and turn the light

switch to position .

supply is cut off.

●

In fog, snow and heavy rain.

With dust and sand turbulence.

With loose gravel in the field of vision of the

– From the base position, move the main

Activate:

●

beam and turn signal lever forwards

page 144. When the warning lamp 

›››



●

The automatic dipped beam control

is displayed on the instrument panel dis-

play, the main beam assist is switched

on.

camera.

●

() only switches on the dipped beam

when there are no changes in brightness,

and not, for example when it is foggy.

When the field of vision of the camera is

misted up, dirty or covered by stickers, snow,

ice, etc.

– Turn the light switch to a different posi-

tion to  page 143.

›››

– OR: with main beam on, move the turn

signal and main beam lever backwards.

– OR: move the turn signal and main

beam lever forward to manually enable

the main beam. The main beam assist

will then be deactivated.

WARNING

Deacti-

vate:

Main beam assist (Light Assist)*

The convenience features of the main

beam assist should not encourage the tak-

ing of risks. The system is not a replace-

ment for driver concentration.

The main beam assist acts within the limits of

the system and depending on environmental

and traffic conditions. Once switched on, the

system is activated as of a speed of about 60

km/h (37 mph) and is deactivated below

●

You are always in control of the main

Malfunctions

beam and adapting it to the light, visibility

and traffic conditions.

about 30 km/h (18 mph)

.

›››

»

The following conditions may prevent the

main beam headlight control from turning off

145

Operation

Fog lights

Fog lights with cornering light func-

tion*

●

It is possible that the main beam head-

light control does not recognise all driving

situations and is limited under certain cir-

cumstances.

The cornering light function is an additional

function to the dipped beam headlights to

improve lighting of the side of the road when

taking a sharp turn at low speed.

●

When the field of vision of the camera is

dirty, covered or damaged, operation of

the main beam control may be affected.

This also applies when changes are made

to the vehicle lighting system, for example,

if additional headlights are installed.

The cornering light function works when the

dipped beam headlights are already on and

it is enabled when driving at speeds below

approximately 40 km/h (25 mph).

CAUTION

Fig. 151 Instrument console: light panel.

To avoid affecting the operation of the sys-

tem, take the following points into consid-

eration:

Forward gear

●

If the steering wheel is turned to the right or

the right-hand turn signal switched on, the

right-hand fog lamp is gradually switched on.

If the steering wheel is turned to the left or

the left-hand turn signal switched on, the left-

hand fog lamp is gradually switched on.

The warning lamps  or  also show, on the

light switch or instrument panel, when the fog

lights are on.

●

Clean the field of vision of the camera

regularly and make sure it is free of snow

and ice.

●

Turn on the fog lights* ; pull the light

●

1

switch to the first point Fig. 151 , from

›››

Do not cover the field of vision of the

camera.

●

positions ,  or .

●

After the turn, the cornering light function is

gradually switched off.

Check that the windscreen is not dam-

●

Turn on the rear fog light : completely pull

the light switch

.

To switch off the fog lights, press the light

switch or turn it to position .

aged in the area of the field of vision of the

camera.

2

from position ,  or

Reverse gear

●

When engaging the reverse gear, both fog

lights turn on.

Note

Main beam and headlight flasher can be

turned on and off manually at any time with

the turn signal and main beam lever

›››

Note

The rear fog light can dazzle drivers behind

you. You should use the rear fog light only

when visibility is very poor.

Function “Coming home”

page 144.

This function may be connected/disconnec-

ted through the radio menu. The “Coming

146

Lights and visibility

●

Home” and/or “Leaving Home” delay time

may also be set (default: 30 sec).

Activate the headlight flashers for approxi-

Vehicle

In the “Leaving Home” function, the

daytime running lights (DRL), the rear

mately 1 second.

●

with halo-

gen head- side lights and the licence plate lights

Activated for any position of the rotary light

lights

are switched on.

Vehicle

In the “Coming Home” function, the

daytime running lights (DRL), the rear

switch.

●

with halo-

Vehicle

In the “Leaving Home” function, the

dipped beams, the daytime running

When the car door is opened, the “Coming

gen head- side lights and the licence plate lights

with full-

lights

are turned on.

Home” lighting comes on. The headlights are

turned off 60 seconds after the vehicle door

is opened.

LED head- lights (DRL), the rear side lights and

lights

the licence plate lights are switched

on.

Vehicle

In the “Coming Home” function, the

dipped beams and the daytime run-

with full-

LED head- ning lights (DRL), the rear side lights

lights

and the licence plate lights are

switched on.

Deactivation

●

Activation

If no door has been closed, they go out au-

●

When the vehicle is unlocked using the re-

mote control.

tomatically after 60 seconds.

●

Automatic* activation of “Coming Home”

After the last door has been closed, the

●

The “Leaving Home” function is only activa-

For vehicles with a light and rain sensor (rota-

ry light switch in position ).

headlights will be switched off after the

“Coming Home” delay (as established in the

radio menu) has elapsed.

ted when the rotary light switch is in position

 and the light sensor detects darkness.

●

Switch off the engine and remove the key

●

On turning the light switch to position 

^››› ^{page 32.}

Deactivation

from the ignition with the rotary light switch in

position 

^››› ^{page 32.}

●

When the “Leaving Home” delay period

●

When the ignition is switched on (when

●

The automatic “Coming Home” function is

only active when the light sensor detects

darkness.

ends (default: 30 sec).

starting the engine).

●

When the vehicle is locked using the remote

control.

●

When the car door is opened, the “Coming

●

When the light control is switched into a po-

Function “Leaving Home”

Home” lighting comes on.

sition other than .

●

With the ignition is switched on.

The “Leaving Home” function is only available

for vehicles with a light and rain sensor (rota-

ry light switch in position ).

Manual “Coming Home” activation

For vehicles with a light and rain sensor (rota-

ry light switch without position ).

This function may be connected/disconnec-

ted through the radio menu. The “Leaving

Home” function switch-off delay may also be

set (default: 30 sec).

●

Switch off the engine and remove the key

from the ignition.

147

Operation

6. Use the warning triangle to draw the at-

tention of other road users to your vehicle.

Hazard warning lights 

could come into contact with highly inflam-

mable materials, for example dry grass or

spilt petrol. This could start a fire.

7. Always take the vehicle key with you when

you leave the vehicle.

Note

All turn signals flash simultaneously when the

hazard warning lights are switched on. The

two turn signal turn signal lamps   and the

turn signal lamp in the switch  will flash at

the same time. The simultaneous hazard

warning lights also work when the ignition is

switched off.

●

The battery will run down if the hazard

warning lights are left on for a long time,

even if the ignition is switched off.

●

The use of the hazard warning lights de-

scribed here is subject to the relevant stat-

utory requirements.

Fig. 152 Dashboard: switch for hazard warning

lights.

Emergency braking warning

Parking lights 

If the vehicle brakes suddenly and continu-

ously at a speed of more than 80 km/h (50

mph), the brake light flashes several times per

second to warn the vehicles driving behind. If

you continue braking, the hazard warning

lights will come on automatically when the

vehicle comes to a standstill. They switch off

automatically when the vehicle starts to

move again.

Read the additional information carefully

^››› ^{page 33}

When the parking light is switched on, (right

or left turn signal), the front side light and the

rear light on the corresponding side of the ve-

hicle stay lit. The parking lights can only be

activated with the ignition switched off and

the turn signal and main beam lever in the

central position, before being triggered.

The hazard warning lights are used to draw

the attention of other road users to your vehi-

cle in emergencies.

If your vehicle breaks down:

1. Park your vehicle at a safe distance from

moving traffic.

WARNING

The risk of an accident increases if your

vehicle breaks down. Always use the haz-

ard warning lights and a warning triangle to

draw the attention of other road users to

your stationary vehicle.

2. Press the button to switch on the hazard

Parking light on both sides

●

warning lights

.

›››

3. Switch the ignition off.

4. Apply the handbrake.

With the ignition switched off and the light

switch in position , when locking the vehicle

from the outside, the parking lights on both

sides of the vehicle light up. In doing so, only

the side lights of both headlights light up, and

additionally the tail lights will do so partially.

5. For a manual gearbox, engage 1st gear;

for an automatic gearbox, move the gear

lever to P.

●

Due to the high temperatures that the

catalytic converter can reach, never park

in an area where the catalytic converter

148

Lights and visibility

designated points of the light distribution. This

is known as “Tourist light”.

cle load status. This offers the driver optimum

visibility and the headlights do not dazzle on-

Motorway light*

coming drivers

.

›››

The motorway light is available on vehicles

equipped with full-LED lights.

The light distribution that the halogen and

full-LED headlights of the SEAT Leon range

have allows the specific “tourist light” values

to be met without the need for stickers or

changes in the settings.

The headlights can only be adjusted when

the dipped beam is switched on.

The function is connected/disconnected via

the corresponding Easy Connect system

menu.

To reset, turn switch Fig. 153:

›››

Value Vehicle load status^a)

●

Activation: when going above 110 km/h

Note

(68 mph) for more than 30 seconds, the dip-

ped beam raises slightly to increase the driv-

er's visibility distance.

Two front occupants, luggage compart-

“Tourist light” is only allowed temporarily. If

you are planning a long stay in a country

that drives on the other side, you should

take the vehicle to an Authorised Technical

Service to change the headlights.





ment empty

All seats occupied, luggage compart-

ment empty

●

Deactivation: when reducing the speed of

the car below 100 km/h (62 mph), the dipped

beam returns to its normal position.

All seats occupied, luggage compart-

ment full. With trailer and minimum

drawbar load.





Headlight range control

Driver only, luggage compartment full

With trailer and maximum drawbar load.

Driving abroad

The light beam of the dipped beam lights is

asymmetric: the side of the road on which

you are driving is lit more intensely.

a)

If the vehicle load does not correspond to those

shown in the table, it is possible to select intermediary

positions.

When a car that is manufactured in a country

that drives on the right travels to a country

that drives on the left (or vice versa), it is nor-

mally necessary to cover part of the head-

light bulbs with stickers or to change the ad-

justment of the headlights to avoid dazzling

other drivers.

OR:

Using the Easy Connect system, by means of

the  /  button and the function button

Vehicle > SETTINGS > Lights > Head-

light height adjustment

^››› ^{page 35.}

Fig. 153 Next to the steering wheel: regulator

headlight range control.

In such cases, the regulations specify certain

light values that must be complied with for

Two front occupants, luggage com-

Setting 0

»

partment empty

The lights range control adapts according to

the value of the headlight beam and the vehi-

149

Operation

Lighting of the instrument panel,

screens and controls

Interior and reading lights¹⁾

All seats occupied, luggage compart-

ment empty

Setting 1

Setting 2

Read the additional information carefully

^››› ^{page 34}

All seats occupied, luggage compart-

ment full. With trailer and minimum

drawbar load.

Depending on the model, the lighting of the

instrument panel and controls can be adjus-

ted in the Easy Connect system, using the

 /  button and the Vehicle > SET-

Glove compartment and luggage com-

partment lighting*

Driver only, luggage compartment full

Driving with trailer and minimum

drawbar load.

Setting 3

TINGSfunction button

^››› ^{page 35.}

When opening and closing the glove com-

partment on the front passenger side and the

rear lid, the respective light will automatically

switch on and off.

With the ignition on and without light activa-

tion, the analogue instrument panel lighting

remains activated in daytime light conditions.

The lighting is reduced as the exterior light di-

minishes. In some cases, e.g. when driving

through a tunnel without the  function ac-

tive, the instrument panel lighting may even

switch off. The objective of this function is to

provide the driver with a visual indication that

he or she should activate the dipped beam.

Dynamic headlight range control

The control is not mounted in vehicles with

dynamic headlight range control. The head-

light range is automatically adjusted accord-

ing to the vehicle load status when they are

switched on.

Footwell lighting*

The lights in the footwell area below the dash

(driver and front passenger sides) will switch

on when the doors are opened and will de-

crease in intensity while driving. This bright-

ness can be adjusted using the Easy Connect

system, by means of the  /  button and

the function button Vehicle > SETTINGS >

Lights > Interior lighting

WARNING

Heavy objects in the vehicle may mean

that the headlights dazzle and distract oth-

er drivers. This could result in a serious ac-

cident.

If your vehicle is equipped with a digital in-

strument panel (Digital SEAT Cockpit), the

following message will appear Turn on the

lightson the instrument panel.

^››› ^{page 35).}

●

Adjust the light beam to the vehicle load

status so that it does not blind other driv-

ers.

1)

Depending on the features fitted in the vehicle,

LEDs can be used for the following interior lights:

front vanity mirror light, rear vanity mirror light,

footwell light, sun blind and glove compartment

light.

150

Lights and visibility

Ambient light*

The lamp goes out when the vanity mirror

cover is closed or the sun visor is pushed

back up.

Visibility

The ambient light lights up the area of the

centre console, the footwell area and, de-

pending on the version, the front door panels.

Sun visors

WARNING

Folded sun blinds can reduce visibility.

The ambient lighting in the door panels may

change colour. The brightness and colour

can be adjusted using the Easy Connect sys-

tem, by means of the  /  button and

the function button Vehicle > SETTINGS >

Lights > Interior lighting

●

Always store sun blinds and visors in their

housing when not in use.

Note

^››› ^{page 35).}

The light above the sun visor automatically

switches off after a few minutes in certain

conditions. This prevents the battery from

discharging.

Note

The reading lights switch off when the vehi-

cle is locked using a key or after several mi-

nutes if the key is removed from the ignition.

This prevents the battery from discharging.

Fig. 154 Sun visor

Options for adjusting driver and front pas-

senger sun visors:

Sun blind*

3 Applies to the model: LEON ST

●

Lower the sun visor towards the wind-

screen.

●

The sun visor can be pulled out of its

mounting and turned towards the door

1

Fig. 154

.

›››

●

Swing the sun visor towards the door, longi-

tudinally backwards.

Vanity mirror light

There may be a vanity mirror, with a cover, on

the rear of the sun visor. When the cover is

»

Fig. 155 Rear window: sun blind.

2

opened

a light comes on.

151

Operation

Rear window sun blind*

●

In icy conditions, always check that the

Windscreen wipers performance in differ-

ent situations

wiper blades are not frozen to the glass be-

fore using the wipers. In cold weather, it

may help to leave the vehicle parked with

the wipers in service position

–

Pull out the visor and hook it into the hooks

in the centre of the top of the door frame

The air conditioner comes on

for approximately 30 seconds

Fig. 155.

›››

During automatic

wipe

in air recirculation mode to pre-

vent the smell of the wind-

screen washer fluid entering

the inside the vehicle.

^››› ^{page 61.}

Windscreen wiper and win-

dow wiper systems

Note

●

The windscreen and window wipers only

Intervals between wipes de-

pend on the vehicle's speed.

The higher the vehicle speed

the shorter the intervals.

For the interval

wipe

function when the ignition is switched on

and the bonnet or rear lid, respectively, are

closed.

Window wiper lever

●

Read the additional information carefully

^››› ^{page 34}

The interval wipe speed varies according

Heated windscreen washer jets

to the vehicle speed. The faster the vehicle

is moving, the more often the windscreen is

cleaned.

The heating only thaws the frozen jets, it does

not thaw the water in the washer hoses.

When the ignition is switched on the heated

windscreen washer jets automatically adjust

the heat depending on the ambient tempera-

ture.

CAUTION

●

The rear wiper is automatically switched

If the ignition is switched off with the wind-

screen wipers active, they complete their

wipe before returning to the rest position.

Ice, snow and other obstacles on the wind-

screen may damage the wiper and the

windscreen wiper motor.

on when the windscreen wiper is on and the

car is in reverse gear.

Headlight wash/wipe system

Windscreen wiper functions

●

If necessary, remove snow and ice from

The headlight washers/wipers clean the

headlight lenses.

the windscreen wipers before starting your

journey.

Windscreen wipers performance in differ-

ent situations

After the ignition is switched on, the first and

every fifth time the windscreen washer is

switched on, the headlights are also washed.

Therefore, the windscreen wiper lever should

be pulled towards the steering wheel when

the dipped beam or main beam are on. Any

encrusted dirt (such as insects) should be

cleaned regularly (e.g. when refuelling).

●

Carefully lift the frozen windscreen wip-

The activated position provi-

If the vehicle is at a

ers from the glass. SEAT recommends a de-

icer spray for this operation.

sionally changes to the previ-

standstill

ous position.

●

Do not switch on the windscreen wipers if

the windscreen is dry. Cleaning with the

windscreen wipers while dry can cause

damage.

152

Lights and visibility

To ensure the headlight washers work cor-

rectly in winter, any snow which has got into

the bumper jet supports should be cleaned

away. If necessary, remove snow with an an-

ti-icing spray.

Rain sensor modified behaviour

Possible causes of faults and mistaken read-

ings on the sensitive surface Fig. 157 of the

›››

rain sensor include:

●

Damaged wipers: a film of water on the

Note

damaged blades may lengthen the activa-

tion time, reduce the washing intervals or re-

sult in a fast and continuous wipe.

The wiper will try to wipe away any obsta-

cles that are on the windscreen. The wiper

will stop moving if the obstacle blocks its

path. Remove the obstacle and switch the

wiper back on again.

●

Insects: insects on the sensor may trigger

Fig. 157 Rain sensor sensitive surface

the windscreen wiper.

●

Salt on the road: in winter, salt spread on

The rain sensor controls the frequency of the

windscreen wiper intervals, depending on the

the roads may cause an extra long wipe

when the windscreen is almost dry.

amount of rain

. The sensitivity of the rain

›››

Rain sensor*

●

Dirt: dry dust, wax, coating on glass (Lotus

sensor can be adjusted manually. Manual

effect) or traces of detergent (car wash) may

reduce the effectiveness of the rain sensor or

make it react more slowly, later or not at all.

wipe page 152.

›››

Move the lever to the required position

Fig. 156:

›››

●

Windscreen crack: the impact of a stone

will trigger a single wipe cycle with the rain

sensor on. Next the rain sensor detects the re-

duction in the sensitive surface area and

adapts accordingly. The behaviour of the

sensor will vary with the size of the damage

caused by the stone.

0

1

Rain sensor off.

Rain sensor on; automatic wipe if neces-

sary.

A

Setting sensitivity level of rain sensor

–

Set control to the right: high sensitivity.

–

Set control to the left: low sensitivity.

Fig. 156 Windscreen wipers lever: adjust the

WARNING

A

rain sensor

.

When the ignition is switched off and then

back on, the rain sensor stays on and starts

operating again when the windscreen wipers

are in position

at more than 16 km/h (10 mph).

The rain sensor may not detect enough rain

to switch on the wipers.

●

If necessary, switch on the wipers man-

ually when water on the windscreen ob-

structs visibility.

1

and the vehicle is travelling

»

153

Operation

Adjusting the exterior rear-view

mirrors

Note

be rinsed with large quantities of water. If

necessary, get medial help.

●

Clean the sensitive surface of the rain

sensor regularly and check the blades for

damage Fig. 157 (arrow).

›››

CAUTION

●

To remove wax and coatings, we recom-

In the event that an automatic anti-dazzle

rear vision mirror breaks, an electrolyte flu-

id may leak. This liquid attacks plastic sur-

faces. Clean it with a wet sponge as soon

as possible.

mend a window cleaner containing alco-

hol.

Mirror

Note

●

If the light incident in the interior rear vi-

Anti-dazzle rear view mirror

sion mirror is obstructed (e.g. with the sun

blind*), the anti-dazzle rear vision mirror

with automatic setting will not operate per-

fectly.

Fig. 158 Driver door: control for the exterior

mirror.

Your vehicle is fitted with an interior rear vision

mirror with a manual or automatic* control

for anti-dazzle position.

Read the additional information carefully

●

page 21

When the interior lights are on or reverse

›››



gear engaged, the mirrors do not darken

with automatic adjustment for anti-dazzle

position.

Interior rear vision mirror with manual set-

ting for anti-dazzle position

Synchronized regulation of the exterior

mirrors

●

Position the small lever of the lower edge of

●

In the Settings - Conveniencemenu,

the mirror to face towards the rear.

select whether or not the exterior mirrors

should move in synchronisation.

WARNING

1)

●

Turn the knob to position L .

In the event that an automatic anti-dazzle

rear vision mirror breaks, an electrolyte flu-

id may leak. This could cause irritation to

the skin, eyes and respiratory organs. If you

come into contact with this liquid, it must

●

Adjust the left-hand exterior mirror. The

right exterior mirror will be adjusted at the

same time (synchronised).

1)

Regulation in right-hand drive vehicles is sym-

metrical.

154

Lights and visibility

1)

●

If necessary, correct the right-hand rear-

Select the R position on the control.

mirrors to estimate the distance to vehicles

behind you when changing lane, you could

misjudge the distance. Risk of accident!

view mirror: rotate the control to position R¹⁾.

●

Select reverse gear.

In the Easy Connect system the exterior

Adjust the front passenger exterior mirror so

that you can see, for example, the kerb area

well.

mirrors can be adjusted using the  / 

button and the Vehicle > SETTINGSfunc-

tion button.

CAUTION

●

Release the reverse gear.

If one of the mirror housings is knocked

out of position (e.g. when parking), the mir-

rors must first be fully retracted with the

electric control. Do not readjust the mirror

housing by hand, as this will interfere with

the mirror adjuster function.

●

The adjusted position for the rear view mir-

Tilt function for front passenger exterior

mirror*

ror is stored.

When parking backwards, and in order to be

able to see the kerb, the passenger side mir-

ror can be automatically tilted towards the

passenger to provide a better view of the

kerb. The control must be in the position R¹⁾

for this feature to be operational.

Fold the rearview mirrors when locking the

vehicle*

●

Before washing the vehicle in an auto-

The Easy Connect system, the  /  but-

ton and the function buttons Vehicles >

SETTINGS > Mirrors and windscreen

wiperscan be used to have the exterior mir-

rors fold in when the vehicle is parked and

matic car wash, please make sure to re-

tract the exterior mirrors to prevent them

from being damaged. Electrically retracta-

ble exterior mirrors must not be folded in or

out by hand. Always use the electrical

power control.

The mirror returns to its original position as

soon as you drive forward at over 15 km/h

(9 mph) or switch off the ignition. It also re-

turns to its original position if the position of

the control is adjusted.

locked

^››› ^{page 35.}

When the vehicle is locked with the remote

control, the exterior mirrors are retracted au-

tomatically. When the vehicle is opened with

the remote control, the exterior mirrors are

deployed automatically.

Note

If the electrical adjustment should fail to

operate, both of the mirrors can be adjus-

ted by hand by lightly pressing the edge of

the mirror glass.

Storing the rear view mirror settings for the

tilt function

●

Switch the ignition on.

WARNING

●

Access the Easy Connect system, button

Convex or wide-angle* exterior mirrors

give a larger field of vision. However, they

make objects look smaller and further

away than they really are. If you use these

 /  and the Vehicle > SETTINGS >

Rear view mirrors and windscreen

wipersbutton and select lower while re-

versing

^››› ^{page 35.}

1)

Regulation in right-hand drive vehicles is sym-

metrical.

155

Operation -> Lights and visibility for Your Seat Leon 4 Door Third Generation (2012-2020)

Related Topics

Popular Owner Manuals

Latest Owner Manuals