2018-2026 Skoda Kamiq SUV Wheels -> Tyre pressure monitor User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Wheels -> Tyre pressure monitor for Your Skoda Kamiq SUV First Generation (2018-2026)

166 Wheels Tyre pressure  
Inflate tyres  
This information only serves as information for  
the prescribed tyre pressure. This is not a listing  
of approved tyre sizes for your vehicle. These  
are in the vehicle's technical documentation, as  
well as in the declaration of conformity (in the  
so-called COC document).  
Fit the tyre inflation hose of the air compressor to  
the tyre valve.  
Secure the vehicle with the parking brake.  
Start the engine.  
Plug the connector into the 12 volt socket .  
Turn on the air compressor.  
Once a tyre pressure of 2.0-2.5 bar is reached, turn  
off the air compressor.  
Tyre pressure reading for the front axle tyres  
E
F
Tyre pressure reading for the rear axle tyres  
Prescribed tyre pressure value for the emergen-  
cy wheel  
G
Observe the maximum running time of the air com-  
pressor according to the directions of the repair kit  
manufacturer.  
Tyre pressure monitor  
Functionality  
If an air pressure of 2.0 - 2.5 bar has not been  
reached, remove the tyre inflation hose from the  
valve.  
The tyre pressure monitoring indicator indicates a  
change in tyre pressure.  
Drive approx. 10 metres forwards or backwards to  
allow the sealing agent to distribute in the tyre.  
Replace the tire inflation hose on the valve and re-  
peat the inflation procedure.  
Warning when pressure changes  
illuminates  
Stop the vehicle.  
Check the tyres and tyre pressures.  
Tyre pressure  
What you should be mindful of  
Show tyres with modified pressure  
In the following menu, select the menu item for  
displaying the tyre condition:  
NOTICE  
Always adjust the tyre pressure to the load.  
Check the pressure in all tyres at least once a  
month and before each longer ride.  
Or:  
Check the pressure when the tyres are cold. Do  
not reduce the higher pressure of warm tyres.  
After each change in tyre pressure, save the new  
values in the tyre control display.  
Function restriction  
WARNING  
Risk of an accident!  
If tyre pressure loss is very quick, try to stop the  
vehicle carefully without heavy steering or heavy  
braking.  
The system is unable to provide a warning in the  
event of a very rapid tyre pressure loss, e.g. sudden  
puncture.  
The system function may be restricted in the follow-  
ing cases:  
Uneven loading of the wheels, e.g. with a trailer at-  
tached  
Sticker with prescribed tyre pressures  
Sporty driving style  
Driving on dirt roads  
Snow chains fitted  
The sticker with prescribed tyre pressures is located  
on the inside of the fuel filler flap.  
Inflation pressure for  
half load  
A
Inflation pressure for  
environmentally  
friendly operation  
(slightly lower fuel  
consumption and  
emissions)  
Inflation pressure for  
a full load  
Tyre diameter in in-  
Saving tyre pressure values  
B
Store the tyre pressure values in the infotainment  
Inflate the tyres to the prescribed inflation pres-  
sure.  
Turn on the ignition.  
In the following menu, select the menu item for  
displaying the vehicle condition:  
C
D
ches  
Or:  
Wheels › Wheel bolt cover caps 167  
Installing  
Press the wheel trim onto the wheel rim at the  
designated valve opening.  
Using the functional surfaces  
control display menu.  
Tap on the functional surface  
select the tyre  
.
When using an anti-theft wheel bolt, it must be lo-  
cated at the location indicated on the bezel.  
Press the trim, starting at the valve, into the rim on  
both sides until it engages around the entire cir-  
cumference.  
Then follow the instructions on the screen.  
Save the tyre pressures in the following cases:  
Change of tyre pressure  
Change of one or more wheels  
Change of position of a wheel on the vehicle  
Always after covering a distance of 10,000 km or  
once a year  
NOTICE  
Use hand pressure, do not hit the wheel cover.  
Troubleshooting  
Tyre pressure display faulty  
flashes for about 1 minute and stays on  
Stop the vehicle, switch off the ignition and  
start the engine.  
If the symbol flashes again after starting the en-  
gine, there is a system fault.  
Continue driving, exercising appropriate caution,  
and seek the help of a specialist garage.  
Wheel bolt cover caps  
Remove cover caps and install  
Disconnecting  
Push the pull-off clamp  
onto the cover cap up  
to the stop.  
Remove the cover cap.  
Installing  
Push the cover cap onto the wheel bolt to the stop.  
Full wheel frame  
Removing and installing the trim  
Applies to factory built or original accessory trims  
from ŠKODA.  
Disconnecting  
Hang the clamps for removing the wheel trims at  
the edge of one of the openings in the trim.  
Push the wheel wrench through the clamp, support  
on the tyre and pull off the wheel trim.  

Related Topics

Popular Owner Manuals