Get Keys Guide for Subaru XV SUV Third Generation (2022-2026)

(105,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

S02

Keys ......................................................................... 2-2

Key number plate................................................... 2-2

Keyless access with push-button start system

(if equipped) ......................................................... 2-2

Safety precautions ................................................. 2-3

Locking and unlocking by holding the access

key fob ................................................................ 2-6

Unlock using PIN Code Access .............................2-10

Power saving function .......................................... 2-11

Power saving function of access key fob ..............2-12

Disabling keyless access function......................... 2-12

Selecting audible signal operation......................... 2-13

Warning chimes and warning indicator.................. 2-13

When access key fob does not operate properly ... 2-14

Replacing battery of access key fob......................2-14

Replacing access key fob .....................................2-14

Certification for keyless access with push-button

start system........................................................ 2-14

Immobilizer ............................................................ 2-15

Security indicator light..........................................2-15

Key replacement ...................................................2-15

Certification for immobilizer system ......................2-16

Remote keyless entry system.............................. 2-17

Locking the doors.................................................2-18

Unlocking the doors..............................................2-18

Unlocking the rear gate.........................................2-19

Vehicle finder function ..........................................2-19

Sounding a panic alarm ........................................ 2-19

Setting audible signal operation (models without

“keyless access with push-button start

system”) .............................................................2-19

Replacing the battery............................................ 2-20

Replacing lost transmitters ................................... 2-20

Certification for remote keyless entry system........ 2-20

Door locks............................................................. 2-21

Locking and unlocking from the outside ............... 2-21

Locking and unlocking from the inside ................. 2-22

Automatic door locking/unlocking......................... 2-23

Key lock-in prevention function ............................ 2-24

Battery drainage prevention function .................... 2-24

Alarm system ........................................................ 2-25

Alarm system operation........................................ 2-25

Arming the system ............................................... 2-25

Disarming the system ........................................... 2-26

Alarm system setting............................................ 2-27

If you have accidentally triggered the alarm

system .............................................................. 2-27

Valet mode ........................................................... 2-27

Child safety locks................................................. 2-28

Windows................................................................ 2-28

Power window operation....................................... 2-29

Initialization of power window with one-touch

auto up/down function ....................................... 2-31

Rear gate ............................................................... 2-31

Lock/unlock.......................................................... 2-31

Open/close ........................................................... 2-31

Moonroof (if equipped)......................................... 2-32

Moonroof switches ............................................... 2-33

Sunshade ............................................................. 2-34

Keys and doors

(106,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

Keys

S02AA

NOTE

For models with “keyless access with

push-button start system”, refer to

“Keyless access with push-button start

system” F2-2.

The following keys are provided with the

vehicle.

1) Master key

2) Sub key

3) Key number plate

A key can be used in the following

locations.

. Ignition switch

. Driver’s door

. Glove box

NOTE

Locking/unlocking using the remote

keyless entry system can also be con-

trolled with the buttons on the key. For

detailed information, refer to “Remote

keyless entry system” F2-17.

CAUTION

Do not attach a large key holder or

key case to either key. If it bangs

against your knees while you are

driving, it could turn the ignition

switch from the “ON” position to

the “ACC” or “LOCK” position,

thereby stopping the engine.

& Key number plate

S02AA01

The key number is stamped on the key

number plate attached to the key set. Write

down the key number and keep it in

another safe place, not in the vehicle. This

number is needed to make a replacement

key if you lose your key or lock it inside the

vehicle. Refer to “Key replacement” F2-

15.

Keyless access with push-

button start system (if

equipped)

S02AP

The following access key fobs are pro-

vided with the vehicle.

1) Access key fob

2) Key number plate

The keyless access with push-button start

system allows you to perform the following

functions when you are carrying the

access key fob.

. Locking and unlocking of the doors and

rear gate. Refer to “Locking and unlocking

by holding the access key fob” F2-6.

. Starting and stopping the engine. For

detailed information, refer to “Starting and

stopping engine (models with push-button

Keys and doors/Keys

2-2

(107,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

start system)” F7-12.

. Arming and disarming the alarm sys-

tem. For detailed information, refer to

“Alarm system” F2-25.

NOTE

. Locking/unlocking using the remote

keyless entry system can also be con-

trolled with the buttons on the access

key fob. For detailed information, refer

to “Remote keyless entry system” F2-

17.

. Carefully store the key number plate

supplied with the access key fob. It is

necessary for vehicle repair and addi-

tional registration of access key fobs.

For details, refer to “Key replacement”

F2-15.

An emergency key is attached to each

access key fob.

1) Release button

2) Emergency key

While pressing the release button of the

access key fob, take out the emergency

key.

The emergency key is used for the follow-

ing operations.

. Locking and unlocking the driver’s door

. Locking and unlocking the glove box

NOTE

The glove box can be kept locked when

you leave your vehicle and the access

key fob (with the emergency key re-

moved) at a parking facility.

& Safety precautions

S02AP11

WARNING

If you wear an implanted pacemaker

or an implanted defibrillator, stay at

least 8.7 in (22 cm) away from the

transmitting antennas installed on

the vehicle.

The radio waves from the transmit-

ting antennas on the vehicle could

adversely affect the operation of

implanted pacemakers and im-

planted defibrillators.

If you wear electronic medical equip-

ment other than an implanted pace-

maker or an implanted defibrillator,

before using the keyless access

with push-button start system, refer

to “Radio waves used for the key-

less access with push-button start

system” mentioned later, and con-

tact the electronic medical equip-

ment manufacturer for more infor-

mation. The radio waves from the

transmitting antennas on the vehicle

could adversely affect the operation

of the electronic medical equipment.

“Radio waves used for the keyless

access with push-button start sys-

tem”

– CONTINUED –

Keys and doors/Keyless access with push-button start system

2-3

(108,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

. The keyless access with push-

button start system uses radio

waves of the following fre-

quency* in addition to the radio

waves used for the remote key-

less entry system. The radio

waves are periodically output

from the antennas installed on

the vehicle as shown in the

following illustrations.

* Radio frequency: 134 kHz

1) Antennas

CAUTION

. Never leave or store the access

key fob inside the vehicle or

within 6.6 ft (2 m) around the

vehicle (e.g., in the garage). The

access key fob may be locked

inside the vehicle, or the battery

may discharge rapidly. Note that

the push-button ignition switch

may not turn on in some cases

depending on the location of the

access key fob.

. The access key fob contains

electronic components. Observe

the following precautions to pre-

vent malfunctions.

– It is recommended to have the

access key battery replaced at

an authorized SUBARU dealer

to avoid the risk of damage.

– Do not get the access key fob

wet. If the access key fob gets

wet, wipe it off immediately

and let it dry completely.

– Do not apply strong impacts to

the access key fob.

– Never leave the access key

fob in direct sunlight or any-

where that may become hot,

such as on the dashboard. It

Keys and doors/Keyless access with push-button start system

2-4

(109,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

may damage the battery or

cause circuit malfunctions.

– Do not wash the access key

fob in an ultrasonic washer.

– Do not leave the access key

fob in humid or dusty loca-

tions. Doing so may cause

malfunctions.

– Keep the access key fob away

from magnetic sources.

– Do not leave the access key

fob near a personal computer

or home electrical appliance.

– Do not leave the access key

fob near a battery charger or

any electrical accessories.

– Do not apply metallic window

tint or attach metallic objects

to the windows.

– Do not fit non genuine acces-

sories or parts.

. If the access key fob is dropped,

the integrated emergency key in-

side may become loose. Be care-

ful not to lose the emergency key.

. When traveling in an airplane, do

not press the button of the ac-

cess key fob. If any button of the

access key fob is pressed, radio

waves are emitted and may affect

the operation of the airplane.

When carrying the access key

fob in a bag, take measures to

prevent the buttons from being

pressed accidentally.

NOTE

. The operational/non-operational

setting for the keyless access function

can be changed. For the setting proce-

dure, refer to “Disabling keyless ac-

cess function” F2-12.

. For detailed information about the

operation method for the push-button

ignition switch while the keyless ac-

cess function is switched to the non-

operational mode, refer to “Access key

fob – if access key fob does not operate

properly” F9-17.

. The keyless access with push-but-

ton start system uses weak radio

waves. The status of the access key

fob and environmental conditions may

interfere with the communication be-

tween the access key fob and the

vehicle under the following conditions,

and it may not be possible to lock or

unlock the doors or start the engine.

– When operating near a facility

where strong radio waves are trans-

mitted, such as a broadcast station

and power transmission lines

– When products that transmit

radio waves are used, such as an

access key fob or a remote trans-

mitter key of another vehicle

– When carrying the access key fob

of your vehicle together with the

access key fob or the remote trans-

mitter of another vehicle

– When the access key fob is

placed near wireless communica-

tion equipment such as a cell phone

– When the access key fob is

placed near a metallic object

– When metallic accessories are

attached to the access key fob

– When carrying the access key fob

with electronic appliances such as a

laptop computer

– When the battery of the access

key fob is discharged

. The access key fob is always com-

municating with the vehicle and is

continuously using the battery.

Although the life of the battery varies

depending on the operating conditions,

it is approximately 1 to 2 years. If the

battery becomes fully discharged, re-

place it with a new one.

. If an access key fob is lost, it is

recommended that all of the remaining

access key fobs be reregistered. For

– CONTINUED –

Keys and doors/Keyless access with push-button start system

2-5

(110,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

reregistration of an access key fob,

contact a SUBARU dealer.

. For a spare access key fob, contact a

SUBARU dealer.

. Up to 7 access key fobs can be

registered for one vehicle.

. Do not leave the access key fob in

the storage spaces inside the vehicle,

such as the door pocket, dashboard,

inside the corner of the cargo area.

Vibrations may damage the key fob or

turn on the switch, possibly resulting in

a lockout.

. After the vehicle battery is dis-

charged or replaced, initialization of

the steering lock system may be re-

quired to start the engine. In this case,

perform the following procedure to

initialize the steering lock.

(1) Turn the push-button ignition

switch to the “OFF” position. For

details, refer to “Switching power

status” F3-7.

(2) Open and close the driver’s

door.

(3) Wait for approximately 10 sec-

onds.

When the steering is locked, the initi-

alization is completed.

. Do not leave the access key fob in

the following places.

– On the instrument panel

– On the floor

– Inside the glove box

– Inside the door trim pocket

– On the rear seat

– In the cargo area

If you do, the following situations

may occur.

– The access key fob is mistakenly

locked inside the vehicle.

– A false warning issues although

no malfunction actually occurs.

– No warning issues even when

any malfunction occurs.

& Locking and unlocking by

holding the access key fob

S02AP20

When the access key fob is carried within

the operating range, the doors and the rear

gate can be locked/unlocked just by

touching the door handle.

NOTE

The vehicle can also be locked/un-

locked with the remote keyless entry

system. For details, refer to “Remote

keyless entry system” F2-17.

! Operating ranges

S02AP2001

1) Antennas

2) Operating range (approximately 16 to 32

in (40 to 80 cm))

1) LED indicator

Keys and doors/Keyless access with push-button start system

2-6

(111,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

When the access key fob is within either of

the operating ranges of the front doors, the

LED indicator on the access key fob

flashes. When the keyless access func-

tions are disabled, the LED indicator does

not flash unless a button on the access key

fob is pressed.

NOTE

. If the access key fob is placed too

close to the vehicle body, the keyless

access functions may not operate

properly. If they do not operate prop-

erly, repeat the operation from further

away.

. If the access key fob is placed near

the ground or in an elevated location

from the ground, even if it is in the

indicated operating range, the keyless

access function may not operate prop-

erly.

. When the access key fob is within

the operating range, it is possible for

anyone, even someone who is not

carrying the access key fob, to operate

the keyless access function. Note that

the keyless access function can be

operated only by the door handle, door

lock sensor, rear gate opener button or

rear lock button in the operating range

in which the access key fob is detected.

. It is not possible to lock the doors

and rear gate using the keyless access

function when the access key fob is

inside the vehicle. However, depending

on the status of the access key fob and

the environmental conditions, the ac-

cess key fob may be locked inside the

vehicle. Before locking the vehicle,

make sure that you have the access

key fob.

. When the battery of the access key

fob is discharged, or when operating it

in a location with strong radio waves or

noise (e.g., near a radio tower, power

plant, broadcast station or an area

where wireless equipment is used), or

while talking on a cell phone, the

operating ranges may be reduced, or

the keyless access function may not

operate.

In such a case, perform the procedure

described in “Locking and unlocking”

F9-18.

. The doors may lock or unlock when

the car is being washed or exposed to a

significant amount of water that con-

tacts the door handle while the key fob

is still in the operating range.

! How to lock and unlock

S02AP2002

It is possible to perform the following

operations when you are carrying the

access key fob.

. Lock and unlock the doors.

. Unlock and lock the rear gate.

NOTE

. It is not possible to lock the doors

and rear gate using the keyless access

function when the push-button ignition

switch is in the “ACC” or “ON” position.

Refer to “Switching power status” F3-

. If the door handle is gripped with a

gloved hand, the door lock may not be

released.

. If the door lock sensor is touched

three times or more repeatedly, the

system will ignore the sensor opera-

tion.

. When performing the locking proce-

dure too quickly, locking may not have

been completed. After performing the

locking procedure, it is recommended

to pull the REAR door handle to confirm

that the doors have been locked.

. If any of the doors (or the rear gate)

are not fully closed, the following will

occur to alert you that the doors (or the

rear gate) are not properly closed.

– An electronic chirp sounds five

times.

– The hazard warning flashers

flash five times.

. It is possible to lock the doors even

when one of the doors is open. After

– CONTINUED –

Keys and doors/Keyless access with push-button start system

2-7

(112,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

performing the locking procedure,

close the opened door or rear gate to

lock it.

. Within 3 seconds after locking the

doors and the rear gate by using the

keyless access function, it is not pos-

sible to unlock doors and/or the rear

gate by using the keyless access func-

tion.

. When locking, be sure to carry the

access key fob to prevent locking the

access key fob in the vehicle.

. The setting of the hazard warning

flasher operation and the volume of the

audible signal can be changed by your

SUBARU dealer. Contact your SUBARU

dealer for details. Also, for models with

the combination meter display (color

LCD), the setting of the hazard warning

flasher operation can be changed by

operating the combination meter dis-

play (color LCD). For details, refer to

“Keyless Entry System” F3-42.

! Locking with the door lock sensor

S02AP200201

1) Door lock sensor

Carry the access key fob, close all doors

including the rear gate, and touch the door

lock sensor on the door handle. All doors

including the rear gate will be locked. Also,

an electronic chirp will sound once and the

hazard warning flashers will flash once.

! Locking with the rear lock button

S02AP200202

1) Rear lock button

Carry the access key fob, close all doors

including the rear gate and press the rear

lock button. The rear gate and all doors will

be locked. Also, an electronic chirp will

sound once and the hazard warning

flashers will flash once.

Keys and doors/Keyless access with push-button start system

2-8

(113,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

! Unlocking

S02AP200203

Carry the access key fob, and grip the

following door handle.

. The driver’s door handle:

Either only the driver’s door will unlock, or

all doors will unlock.

. The front passenger’s door handle:

All doors and rear gate will be unlocked.

Also, an electronic chirp will sound twice

and the hazard warning flashers will flash

twice.

! Unlocking rear gate

S02AP200204

1) Rear gate opener button

Carry the access key fob, and press the

rear gate opener button. Either only the

rear gate will unlock, or all doors will

unlock. Also, an electronic chirp will sound

twice and the hazard warning flashers will

flash twice.

! Door unlock selection function

S02AP2003

When the door is unlocked using the

keyless access function, only the doors

that were set can be unlocked.

The settings can be changed with the

following methods.

. The setting can be changed by operat-

ing the combination meter display (color

LCD) (if equipped). Refer to “Keyless Entry

System” F3-42.

. The setting can be changed by a

SUBARU dealer.

– CONTINUED –

Keys and doors/Keyless access with push-button start system

2-9

(114,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

& Unlock using PIN Code Ac-

cess

S02AP21

When all doors including the rear gate are

locked, you can unlock the doors (includ-

ing rear gate) without a key by pressing the

rear lock button.

1) Rear lock button

NOTE

PIN Code Access will be helpful if the

key fob is accidentally left in the

vehicle. It is recommended that a 5-

digit security code (PIN code) be regis-

tered.

! Preparation for registering a PIN

code

S02AP2101

1. Turn off the ignition switch.

2. Close all doors (including rear gate).

3. Press and hold the “

” button on the

access key fob. Then all doors (including

rear gate) will be locked.

4. Keep the “

” button pressed, and

press the rear lock button within 5 seconds

after step 3.

5. Press and hold the rear lock button for

more than 5 seconds. Confirm a chirp

sound.

6. Release the “

” button and rear lock

button.

7. Press the “

” button on the access key

fob while the chirp sounds.

Then the chirp will stop and the prepara-

tion is complete.

NOTE

Press the “

” button within 30 seconds

of step 6 to end the preparation mode

and move on to the registration stage.

Unless the “

” button is pressed within

30 seconds after step 6, the PIN code

registration will be canceled.

! Registration for a PIN code

S02AP2102

For example, to register “32468” as the

PIN code, perform the following proce-

dure.

1. Press the rear lock button three times.

2. After a chirp sounds once, press the

rear lock button twice.

3. After a chirp sounds once, press the

rear lock button four times.

4. After a chirp (ding) sounds once, press

the rear lock button six times.

5. After a chirp (ding) sounds once, press

the rear lock button eight times.

6. Perform steps 1 to 5 again within

approximately 30 seconds after the chirp

starts sounding intermittently.

7. All doors will be unlocked and locked.

Then the PIN code will be registered.

NOTE

. Press the rear lock button ten times

to enter “0”.

. Change the PIN code frequently to

protect your vehicle from theft.

. If you have lent your vehicle to

another person, confirm that the PIN

code has not been changed or deleted.

If the PIN code has been changed or

deleted, reregister a new PIN code.

. If you make an error during the

registration procedure, press the “

”

Keys and doors/Keyless access with push-button start system

2-10

(115,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

or “ ” button on the access key fob.

Then, start over from the procedure

described in “Preparation for register-

ing a PIN code”.

. To protect your vehicle from theft,

you cannot register a string of the same

five numbers together, such as

“00000”, nor “12345” as a PIN code.

. Do not register your vehicle license

plate number or simple numbers such

as “11122” or “12121” as a PIN code.

Doing so will increase the risk of

vehicle theft.

. When you try to register “22222”, the

registered PIN code will be deleted. You

cannot unlock the doors by PIN Code

Access until a new code is registered.

. After registering a new PIN code,

make sure that you can unlock the

doors using the PIN code.

. The PIN code cannot be deleted

while the keyless access function is

disabled by operating the access key

fob.

. Reregister the PIN code in the fol-

lowing case.

– When you forget the PIN code

– When you want to change the PIN

code

! Unlocking

S02AP2103

Perform steps 1 to 5 described in “Regis-

tration for a PIN code”.

NOTE

. You cannot unlock by PIN Code

Access in the following cases.

– The access key fob is within the

operating ranges.

– The ignition switch is in the

“ACC” or “ON” position.

. If you make an operation error dur-

ing the unlocking procedure, start over

with the unlocking procedure after

waiting for 5 seconds or longer.

. To protect your vehicle from theft, a

buzzer will sound if incorrect PIN codes

are entered five times continuously. If

this occurs, you cannot unlock the

doors by PIN Code Access for 5

minutes.

& Power saving function

S02AP23

The keyless access function will be dis-

abled in the following cases to protect the

access key fob battery and the vehicle

battery.

. Case 1: When the keyless access

function and the remote keyless entry

system have not been used for 2 weeks

or longer while all doors are locked.

Operate one of the following items to

recover the keyless access function:

– Unlock the doors by operating any

procedure other than gripping the front

passenger’s door handle.

– Lock the doors.

– Open a door and then close it.

. Case 2: When the access key fob has

been left in the operating range for 10

minutes or longer while all doors are

locked.

Operate one of the following items to

recover the keyless access function:

– Unlock the doors by gripping the

door handle.

– Unlock the doors by pressing the

rear gate opener button.

– Lock the doors by touching the door

lock sensor.

– Lock or unlock the doors by using

the remote keyless entry system.

– Lock or unlock the doors by using

the power door locking switch.

– Open either of the front doors.

– CONTINUED –

Keys and doors/Keyless access with push-button start system

2-11

(116,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

& Power saving function of ac-

cess key fob

S02AP22

This function stops the access key fob

from receiving signals and helps minimize

the battery consumption of the access key

fob.

1. Press the “

” button twice while hold-

ing the “

” button.

1) LED indicator

2. Confirm that the LED indicator blinks 4

times to notify that the setting is complete.

When the access key fob is in the power

save mode, the keyless access function

and push-button start system will not be

available.

To cancel the power save mode, press one

of the buttons on the access key fob.

& Disabling keyless access

function

S02AP07

WARNING

If you wear an implanted pacemaker

or an implanted defibrillator, per-

form the procedure described in

“By operating the driver’s door”

F2-13 to disable the keyless access

function. If you perform the proce-

dure described in “By operating the

access key fob” F2-12, the opera-

tion of an implanted pacemaker or

implanted defibrillator may be af-

fected by the radio waves from the

transmitter antenna.

When the vehicle is not going to be used

for a long time, or when you choose not to

use the keyless access function, the key-

less access function can be disabled.

NOTE

. The locking and unlocking function

by the remote keyless entry system is

not disabled.

. To start the engine while the func-

tions are disabled, perform the proce-

dure described in “Starting engine”

F9-18.

! Disabling functions

S02AP0701

! By operating the access key fob

S02AP070102

If you have registered a PIN code for PIN

Code Access, you can disable the keyless

access function by operating the access

key fob. For details about registering a PIN

code, refer to “Preparation for registering a

PIN code” F2-10.

1. Open the driver’s door.

2. Rotate the lock lever toward the lock

position.

3. Press and hold the “ ” button and “ ”

button on the access key fob simulta-

neously for more than 5 seconds.

A chirp sound will be heard, and the

function will be disabled.

Keys and doors/Keyless access with push-button start system

2-12

(117,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

! By operating the driver’s door

S02AP070101

1. Sit in the driver’s seat, and close the

door.

2. Push “ ” of the power door locking

switch.

3. Within 5 seconds after step 2 is

performed, open the driver’s door.

4. Within 5 seconds after step 3 is

performed, push “

” of the power door

locking switch twice while the door is open.

5. Within 10 seconds after step 4 is

performed, close and open the driver’s

door twice.

6. Within 10 seconds after step 5 is

performed, push “

” of the power door

locking switch twice while the door is open.

7. Within 10 seconds after step 6 is

performed, close and open the driver’s

door once.

8. Within 5 seconds after step 7 is

performed, close the door.

A chirp sound will be heard, and the

functions will be disabled.

NOTE

In steps 4 and 6, press the power door

locking switch slowly. If the switch is

pressed quickly, the functions may not

be disabled.

! Enabling functions

S02AP0702

When the procedure to disable the func-

tions is performed again, a chirp sound will

be heard, and the functions are enabled.

NOTE

. The keyless access function will be

enabled only if you perform the proce-

dure in the same manner you disabled

the function (for example, when dis-

abling by operating the driver’s door,

the function will not be enabled even if

you operate the access key fob).

. Press the push-button ignition

switch if you do not know the proce-

dure in which the keyless access func-

tion was disabled.

– When disabling by operating the

driver’s door: A chirp will not be

heard.

– When disabling by operating the

access key fob: A chirp will be

heard.

& Selecting audible signal op-

eration

S02AP12

Using an electronic chirp, the system will

give you an audible signal when the doors

lock and unlock. If desired, you may turn

the audible signal off. For more details,

contact a SUBARU dealer.

NOTE

For models with the combination meter

display (color LCD), the setting can be

changed by operating the combination

meter display (color LCD). For details,

refer to “Vehicle Setting” F3-42.

& Warning chimes and warning

indicator

S02AP06

The keyless access with push-button start

system sounds a warning chime and

flashes the access key warning indicator

on the combination meter in order to

minimize improper operations and help

protect your vehicle from theft.

For details, refer to “Warning chimes and

warning indicator of the keyless access

with push-button start system” F3-24.

– CONTINUED –

Keys and doors/Keyless access with push-button start system

2-13

(118,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

& When access key fob does

not operate properly

S02AP08

Refer to “Access key fob – if access key

fob does not operate properly” F9-17.

& Replacing battery of access

key fob

S02AP09

Refer to “Replacing battery of access key

fob” F11-46.

& Replacing access key fob

S02AP13

Access key fobs can be replaced at

SUBARU dealers. For more details, con-

tact a SUBARU dealer.

& Certification for keyless ac-

cess with push-button start

system

S02AP14

. U.S.-spec. models

FCC ID: HYQ14AHK

FCC ID: Y8PFJ16-1

FCC ID: Y8PSSPIMB02

CAUTION

FCC WARNING

Changes or modifications not ex-

pressly approved by the party re-

sponsible for compliance could void

the user’s authority to operate the

equipment.

NOTE

This device complies with part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This de-

vice may not cause harmful interfer-

ence, and (2) this device must accept

any interference received, including

interference that may cause undesired

operation.

. Canada-spec. models

Keys and doors/Keyless access with push-button start system

2-14

(119,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

. Mexico-spec. models

IFT

RLVDE1415-1661

14AHK

DENSO

Immobilizer

S02AB

The immobilizer system is designed to

prevent an unauthorized person from

starting the engine. Only keys registered

with your vehicle’s immobilizer system can

be used to operate your vehicle. If engine

start is attempted with an unregistered

access key fob or key, the engine will not

start. Even if the engine does start, it will

stop after a few seconds. This system,

however, is not a 100% anti-theft guaran-

tee.

CAUTION

. Do not place the key under direct

sunlight or anywhere it may be-

come hot.

. Do not get the key wet. If the key

gets wet, wipe it dry with a cloth

immediately.

. Do not modify or remove the

system. If modified or removed,

the proper operation of the sys-

tem cannot be guaranteed.

NOTE

. To protect your vehicle from theft,

please pay close attention to the follow-

ing security precautions:

– Never leave your vehicle unat-

tended with its keys inside.

– Before leaving your vehicle,

close all windows and the moon-

roof, and lock the doors and rear

gate.

– Do not leave spare keys or any

record of your key number in the

vehicle.

. The vehicle has a maintenance-free

type immobilizer system.

& Security indicator light

S02AB02

Refer to “Security indicator light” F3-29.

& Key replacement

S02AB03

Your key number plate will be required if

you ever need a replacement key made.

Any new key must be registered for use

with your vehicle’s immobilizer system

before it can be used. The maximum

number of keys that can be registered for

use with one vehicle is as follows.

. Four (models without “keyless access

with push-button start system”)

– CONTINUED –

Keys and doors/Immobilizer

2-15

(120,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

. Seven (models with “keyless access

with push-button start system”)

One key that has already been registered

is required in order to register a new key.

NOTE

If you lose a key, the lost key’s ID code

still remains in the memory of the

vehicle’s immobilizer system. For se-

curity reasons, the lost key’s ID code

should be erased from the memory. To

erase the lost key’s ID code, all keys

that will be used are required.

For details about new key registration

and erasing the lost key’s ID code,

contact your SUBARU dealer.

& Certification for immobilizer

system

S02AB05

. For models with “keyless access

with push-button start system”:

Refer to “Certification for keyless access

with push-button start system” F2-14.

. For models without “keyless access

with push-button start system”:

– U.S.-spec. models

FCC ID: Y8PFJ16-2

CAUTION

FCC WARNING

Changes or modifications not ex-

pressly approved by the party re-

sponsible for compliance could void

the user’s authority to operate the

equipment.

NOTE

This device complies with part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This de-

vice may not cause harmful interfer-

ence, and (2) this device must accept

any interference received, including

interference that may cause undesired

operation.

– Canada-spec. models

Keys and doors/Immobilizer

2-16

(121,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

– Mexico-spec. models

Remote keyless entry system

S02AQ

CAUTION

. Do not expose the remote trans-

mitter to severe shocks, such as

those experienced as a result of

dropping or throwing.

. Do not take the remote transmit-

ter apart except when replacing

the battery.

. Do not get the remote transmitter

wet. If it gets wet, wipe it dry with

a cloth immediately.

. When you carry the remote trans-

mitter on an airplane, do not

press the button of the remote

transmitter while in the airplane.

When any button of the remote

transmitter is pressed, radio

waves are sent and may affect

the operation of the airplane.

When you carry the remote trans-

mitter in a bag on an airplane,

take measures to prevent the

buttons of the remote transmitter

from being pressed.

Access key fob

1) Lock/arm button

2) Unlock/disarm button

3) Rear gate unlock button

4) PANIC button

– CONTINUED –

Keys and doors/Remote keyless entry system

2-17

(122,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

Transmitter

1) Lock/arm button

2) Unlock/disarm button

3) Rear gate unlock button

4) PANIC button

The remote keyless entry system has the

following functions.

. Locking and unlocking the doors (and

rear gate)

. Unlocking the rear gate

. Sounding a panic alarm

. Arming and disarming the alarm sys-

tem. For detailed information, refer to

“Alarm system” F2-25.

The operable distance of the remote key-

less entry system is approximately 30 feet

(10 meters). However, this distance will

vary depending on environmental condi-

tions. The system’s operable distance will

be shorter in areas near a facility or

electronic equipment emitting strong radio

waves such as a power plant, broadcast

station, TV tower, or remote controller of

home electronic appliances.

NOTE

. For models with “keyless access

with push-button start system”, the

remote keyless entry system will not

be activated when the push-button

ignition switch is in any position other

than the “OFF” position.

. For models without “keyless access

with push-button start system”, the

remote keyless entry system will not

be activated when the key is inserted in

the ignition switch.

. The hazard warning flashers will

flash once or twice when the access

key fob/transmitter button is pressed in

the following cases.

– When locking the doors

– When unlocking the doors

– When unlocking the rear gate

Operation of the hazard warning

flashers in the above cases can be set

to “On” or “Off” by a SUBARU dealer.

Consult your SUBARU dealer for de-

tails.

& Locking the doors

S02AQ01

Press the lock/arm button to lock all doors

and rear gate. An electronic chirp will

sound once and the hazard warning

flashers will flash once.

If any of the doors (or the rear gate) are not

fully closed, the following will occur to alert

you that the doors (or the rear gate) are not

properly closed.

. An electronic chirp sounds five times.

. The hazard warning flashers flash five

times.

When you close the door, it will automati-

cally lock and then the following will occur.

. An electronic chirp sounds once.

. The hazard warning flashers flash

once.

& Unlocking the doors

S02AQ02

Press the unlock/disarm button to unlock

the driver’s door. An electronic chirp will

sound twice and the hazard warning

flashers will flash twice. To unlock all doors

and the rear gate, briefly press the unlock/

disarm button a second time within 5

seconds.

NOTE

If the interval between the first and

second presses of the unlock/disarm

Keys and doors/Remote keyless entry system

2-18

(123,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

button (for unlocking of all of the doors

and the rear gate) is extremely short,

the system may not respond.

& Unlocking the rear gate

S02AQ05

Press the rear gate unlock button to unlock

the rear gate.

An electronic chirp will sound twice and the

hazard warning flashers will flash twice.

& Vehicle finder function

S02AQ07

Use this function to find your vehicle

parked among many vehicles in a large

parking lot. Provided you are within 30 feet

(10 meters) of the vehicle, pressing the

lock/arm button three times in a 5-second

period will cause your vehicle’s horn to

sound once and its hazard warning

flashers to flash three times.

NOTE

If the interval between presses is too

short when you press the lock/arm

button three times, the system may

not respond to the signals from the

remote transmitter.

& Sounding a panic alarm

S02AQ08

To activate the alarm, press the “PANIC”

button once.

The horn will sound and the hazard

warning flashers will flash.

To deactivate the panic alarm, press any

button on the remote transmitter. Unless a

button on the remote transmitter is

pressed, the alarm will be deactivated

after approximately 30 seconds.

& Setting audible signal opera-

tion (models without “keyless

access with push-button start

system”)

S02AQ09

Using an electronic chirp, the system will

give you an audible signal when the doors

lock and unlock. If desired, you may turn

the audible signal off.

Perform the following steps to deactivate

the audible signal. You can also use the

same steps to restore the function.

1. Sit in the driver’s seat and shut all

doors and the rear gate.

2. Hold down “ ” of the power door

locking switch.

3. While holding down “

” of the power

door locking switch, pull the key out and re-

insert it into the ignition switch at least 6

times within 10 seconds after Step 2.

4. Open and close the driver’s door once

within 10 seconds after Step 3.

5. The hazard warning flashers flash 3

times to indicate completion of the setting.

Your SUBARU dealer can perform the

above procedure for you. Also, for models

with a combination meter display (color

LCD), the setting can be changed using

the display. For details, refer to “Vehicle

Setting” F3-42.

– CONTINUED –

Keys and doors/Remote keyless entry system

2-19

(124,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

& Replacing the battery

S02AQ12

Refer to “Replacing key battery” F11-45.

& Replacing lost transmitters

S02AQ13

If you lose a transmitter or want to

purchase additional transmitters (up to

four can be programmed), your transmit-

ters should be reprogrammed for security

reasons. For details, contact your

SUBARU dealer and have the transmitters

programmed into the remote keyless entry

system.

& Certification for remote key-

less entry system

S02AQ18

! U.S.-spec. models

S02AQ1801

FCC ID: CWTB1G077

FCC ID: CWTD1G141

CAUTION

FCC WARNING

Changes or modifications not ex-

pressly approved by the party re-

sponsible for compliance could void

the user’s authority to operate the

equipment.

NOTE

This device complies with part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This de-

vice may not cause harmful interfer-

ence, and (2) this device must accept

any interference received, including

interference that may cause undesired

operation.

! Canada-spec. models

S02AQ1802

Keys and doors/Remote keyless entry system

2-20

(125,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

! Mexico-spec. models

S02AQ1803

IFETEL RLVSUTB15-1814

SUBARU

MODEL: TB1G077

IFETEL RLVSUTD18-0302

SUBARU

MODEL: TD1G141

Door locks

S02AC

& Locking and unlocking from

the outside

S02AC01

NOTE

If you unlock the driver’s door with a

key (including an emergency key) and

open the door while the alarm system is

armed, the alarm system is triggered

and the vehicle’s horn sounds. In this

case, perform any of the following

operations:

. Models with “keyless access with

push-button start system”:

– Press any button on the access

key fob (except when the access

key fob battery is discharged).

– Press the push-button ignition

switch to “ACC”.

– Carry the access key fob and

perform either of the following pro-

cedures.

– Grip the front door handle.

– Press the rear gate opener

button.

. Models without “keyless access

with push-button start system”:

– Press any button on the remote

transmitter (except when the trans-

mitter battery is discharged).

– Insert the key into the ignition

switch and turn the ignition switch

to “ON”.

For details about the alarm system,

refer to “Alarm system” F2-25.

! How to lock and unlock the vehicle

by using the key

S02AC0101

1) Rotate the key toward the front to lock.

2) Rotate the key toward the rear to unlock.

In this case, only the driver’s side door is

locked.

NOTE

Models with “keyless access with

push-button start system”:

The emergency key is directional. If the

key cannot be inserted, change the

– CONTINUED –

Keys and doors/Door locks

2-21

(126,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

direction that the grooved side is facing

and insert it again.

! How to lock the vehicle without

using the key

S02AC0102

To lock the door from outside without the

key, the following methods are available.

! Locking using lock lever

S02AC010201

1) Rotate the lock lever forward.

2) Close the door.

In this way, only the door that was operated

will be locked.

! Locking using power door lock-

ing switch

S02AC010202

1) Press the lock side of the power door

locking switch.*

2) Close the door.

*: For details about the power door locking

switch, refer to “How to operate the power

door locking switches” F2-23.

In this case, all closed doors and the rear

gate are locked at the same time.

NOTE

Make sure that you do not leave the key

inside the vehicle when locking the

doors from the outside without the key.

& Locking and unlocking from

the inside

S02AC02

! How to use the lock lever

S02AC0202

1) Rotate the lock lever rearward to unlock.

2) Rotate the lock lever forward to lock.

Always make sure that all doors and the

rear gate are closed before starting to

drive.

The red mark on the lock lever appears

when the door is unlocked.

WARNING

. Keep all doors locked when you

drive, especially when small chil-

dren are in your vehicle.

Along with the proper use of

Keys and doors/Door locks

2-22

(127,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

seatbelts and child restraints,

locking the doors reduces the

chance of being thrown out of

the vehicle in an accident.

It also helps prevent passengers

from falling out if a door is

accidentally opened, and intru-

ders from unexpectedly opening

doors and entering your vehicle.

. Do not pull the front door handle

from inside while driving. The

door could open even if it is

locked.

! How to operate the power door

locking switches

S02AC0203

All doors and the rear gate can be locked

and unlocked using the power door locking

switches located at the driver’s side and

the front passenger’s side doors.

Example

1) Press to lock.

2) Press to unlock.

NOTE

Make sure that you do not leave the key

inside the vehicle before locking the

doors from the outside using the power

door locking switches.

& Automatic door locking/un-

locking

S02AC08

All doors are automatically locked or

unlocked under the following conditions.

. For automatic door locking

– When the vehicle speed reaches 12

mph (20 km/h) or higher (factory

default setting).

– When the select lever is shifted into

a position other than the “P” position

(CVT models).

. For automatic door unlocking

– When the driver’s door is open

(factory default setting).

– When the ignition switch is turned to

the “OFF” position.

– When the select lever is shifted into

the “P” position (CVT models).

NOTE

. The automatic door locking/unlock-

ing function can be changed by a

SUBARU dealer. Consult your SUBARU

dealer for details. Also, for models with

a combination meter display (color

LCD), the setting can be changed using

the display. For details, refer to “Auto

Door Lock and Unlock” F3-42.

. When locking the door by operating

the power door locking switches, auto-

matic door locking will not operate.

. When unlocking the door by operat-

ing the power door locking switches,

automatic door unlocking will not oper-

ate.

. When getting out of the vehicle from

a rear door, make sure to unlock all the

doors by pushing the unlock side of the

power door locking switch. If a rear

door is unlocked from the inside door

– CONTINUED –

Keys and doors/Door locks

2-23

(128,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

lever then the door is opened and

closed, the Key lock-in prevention

function will be triggered. All doors will

be unlocked, the Key lock-in prevention

warning indicator “

” will appear and

the warning chime will also sound.

& Key lock-in prevention func-

tion

S02AC06

Under the following conditions, all the

doors will not lock when the power door

locking switch is pushed with the front door

open.

. The key is still in the ignition switch

(models without “keyless access with

push-button start system”).

. The ignition switch is in the “ACC” or

“ON” position (models with “keyless ac-

cess with push-button start system”).

NOTE

. When leaving the vehicle, make sure

you are holding the key before locking

the doors.

. The factory setting (default setting)

for this function is set as “operational”.

This function’s operational/non-opera-

tional setting can be changed by a

SUBARU dealer. Contact a SUBARU

dealer for details.

! Non-operation of key lock-in pre-

vention function

S02AC0602

When the system is set so that it does not

operate, the doors are locked by the

following operation.

. If the lock lever is turned to the front

(“LOCK”) position with the driver’s door

open and the driver’s door is then closed

with the lock lever in that position, the

driver’s door is locked.

. If the spare key is used to lock the

driver’s door from the outside of the

vehicle, the door is locked.

& Battery drainage prevention

function

S02AC03

If a door or the rear gate is not completely

closed, the interior lights will remain

illuminated as a result. However, several

lights are automatically turned off by the

battery drainage prevention function to

prevent the battery from discharging. The

following interior lights are affected by this

function.

Item

Switch

position

Automatically turning

off

Map lights DOOR

Approximately 20

minutes later

Dome light DOOR

Approximately 20

minutes later

Item

Switch

position

Automatically turning

off

Ignition

switch light

—

Approximately 20

minutes later

Cargo area

light

DOOR

Approximately 20

minutes later

Rear gate

light (if

equipped)

DOOR

Approximately 20

minutes later

NOTE

. The default setting for this function

is set as “operational”. The operational/

non-operational setting of this function

can be changed by a SUBARU dealer.

Contact your SUBARU dealer to

change the setting.

. When leaving the vehicle, please

make sure that all doors and the rear

gate are completely closed.

. The battery drainage prevention

function does not operate while the

key is in the ignition switch.

Keys and doors/Door locks

2-24

(129,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

Alarm system

S02AF

The alarm system helps to protect your

vehicle and valuables from theft. The horn

sounds and the hazard warning flashers

flash if someone attempts to break into

your vehicle.

For models with “keyless access with

push-button start system”:

The system can be armed or disarmed

with the keyless access function or access

key fob.

The system will not be activated when the

push-button ignition switch is in the “ACC”

or “ON” position.

For models without “keyless access

with push-button start system”:

The system can be armed or disarmed

with the remote transmitter.

The system will not be activated when the

key is inserted into the ignition switch.

Your vehicle’s alarm system has been set

for activation at the time of shipment from

the factory. You can set the system for

deactivation yourself or have it done by

your SUBARU dealer.

& Alarm system operation

S02AF01

When the alarm system is armed, it is

triggered by opening any of the doors, rear

gate or engine hood.

The alarm system will activate the follow-

ing alarms when triggered.

. The vehicle’s horn will sound for 30

seconds.

. The hazard warning flashers will flash

for 30 seconds.

If any of the doors, rear gate or engine

hood remains open after the 30-second

period, the horn will continue to sound for a

maximum of 3 minutes. If the door, rear

gate or engine hood is closed while the

horn is sounding, the horn will stop

sounding with a delay of up to 30 seconds.

NOTE

The alarm system can be set to trigger

the illumination of the following interior

lights.

. Map lights (illuminates only when

the door interlock switch is in the

“DOOR” position)

. Dome light (illuminates only when

the dome light switch is in the “DOOR”

position)

. Cargo area light (illuminates only

when the cargo area light switch is in

the “DOOR” position)

The notifications regarding the map

lights, dome light and cargo area light

are deactivated as the factory setting. A

SUBARU dealer can activate the sys-

tem. Contact your SUBARU dealer for

details.

& Arming the system

S02AF04

The alarm system becomes armed when

the following operation is performed.

1. Close all windows and the moonroof (if

equipped) and turn the ignition switch to

the “OFF” position.

2. Carry the key and get out of the

vehicle.

3. Make sure that the engine hood is

closed.

4. Lock the doors using any of the

following methods.

. Locking using the remote keyless

entry system. For details, refer to

“Remote keyless entry system” F2-17.

. Locking using the keyless access

function (if equipped). For details, refer

to “Locking with the door lock sensor”

F2-8.

. Locking using the power door lock-

ing switch. For details, refer to “Locking

using power door locking switch” F2-

22.

– CONTINUED –

Keys and doors/Alarm system

2-25

(130,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

NOTE

Security indicator light

. All doors and the rear gate will lock,

an electronic chirp will sound once, the

hazard warning flashers will flash once,

and the security indicator light will start

flashing rapidly.

. If any of the doors or the rear gate is

not fully closed, an electronic chirp

sounds five times, the hazard warning

flashers flash five times to alert you that

the doors (or the rear gate) are not

properly closed. When you close the

door, doors will automatically lock.

5. Approximately 30 seconds later, the

system will enter surveillance state.

When the system is in surveillance state,

the security indicator light will then flash

slowly (twice approximately every 2 sec-

onds), indicating that the system has been

armed for surveillance.

NOTE

. The system can be armed even if the

windows and/or moonroof are open.

Always make sure that they are fully

closed before arming the system.

. The 30-second standby time can be

eliminated if you prefer. Have it per-

formed by your SUBARU dealer.

. If any of the following actions is

done during the standby period, the

system will not switch to the surveil-

lance state.

– Doors (including the rear gate)

are unlocked using the access key

fob/remote transmitter.

– Doors (including the rear gate)

are unlocked using the keyless

access function (models with “key-

less access with push-button start

system”).

– Any door (including the rear gate)

is opened.

– The ignition switch is turned to

the “ON” position (models without

“keyless access with push-button

start system”).

– Push-button ignition switch is

turned to the “ACC” position (mod-

els with “keyless access with push-

button start system”).

& Disarming the system

S02AF05

Perform either of the following procedures.

. Briefly press a button (for less than 2

seconds) on the access key fob/remote

transmitter.

. Carry the access key fob and perform

either of the following procedures (models

with “keyless access with push-button

start system”).

– Grip the front door handle.

– Press the rear gate opener button.

– Unlock using the PIN code access.

The flashing of the security indicator light

will then change slowly (once approxi-

mately every 3 seconds from twice ap-

proximately every 2 seconds), indicating

that the alarm system has been disarmed.

! Emergency disarming

S02AF0501

If you cannot disarm the system using the

access key fob/transmitter (i.e. the trans-

mitter is lost, broken or the transmitter

battery is too weak), you can disarm the

system without using the access key fob/

remote transmitter.

The system can be disarmed if you turn the

Keys and doors/Alarm system

2-26

(131,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

ignition switch from the “LOCK”/“OFF” to

the “ON” position with a registered key/

access key fob.

NOTE

For models with “keyless access with

push-button start system”, if the ac-

cess key fob battery is discharged,

perform the procedure described in

“Switching power status” F9-18. In

such a case, replace the battery im-

mediately. Refer to “Replacing battery

of access key fob” F11-46.

& Alarm system setting

S02AF11

To change the setting of your vehicle’s

alarm system for activation or deactiva-

tion, do the following.

1. Disarm the alarm system. Refer to

“Disarming the system” F2-26.

2. Sit in the driver’s seat and shut all

doors, rear gate and engine hood.

3. Turn the ignition switch to the “ON”

position.

4. Hold down “

” of the driver’s power

door locking switch, open the driver’s door

within the following 1 second, and wait 10

seconds without releasing the switch. The

setting will then be changed as follows.

. Type A combination meter

Setting

status

Combination

meter display

Horn

Activate ALon Once

Deactivate ALoF

Twice

. Type B combination meter

Setting

status

Combination

meter display

Horn

Activate AL ON Once

Deactivate AL OFF

Twice

NOTE

You may have the above setting change

done by your SUBARU dealer.

& If you have accidentally trig-

gered the alarm system

S02AF03

! To stop the alarm

S02AF0301

Do any of the following operations:

. Press any button on the access key fob/

remote transmitter.

. Turn the ignition switch to the “ON”

position (models without “keyless access

with push-button start system”).

. Turn the push-button ignition to the

“ACC” position (models with “keyless

access with push-button start system”).

NOTE

Only registered keys will stop the

alarm. If the immobilizer transponder

is not registered, the alarm will not

stop.

& Valet mode

S02AF06

When you choose the valet mode, the

alarm system does not operate. In valet

mode, the remote transmitter is used only

for locking and unlocking the doors and

rear gate and panic activation.

To enter the valet mode, change the

setting of your vehicle’s alarm system for

deactivation mode. Refer to “Alarm system

setting” F2-27. The security indicator light

will continue to flash once every 3 seconds

indicating that the system is in the valet

mode.

To exit valet mode, change the setting of

your vehicle’s alarm system for activation

mode. Refer to “Alarm system setting” F2-

27.

Keys and doors/Alarm system

2-27

(132,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

Child safety locks

S02AG

Each rear door has a child safety lock.

When the child safety lock lever is in the

lock position, the door cannot be opened

from inside. The door can only be opened

from the outside.

WARNING

Always turn the child safety locks to

the “LOCK” position when children

sit in the rear seat. Serious injury

could result if a child accidentally

opens the door and falls out.

Windows

S02AH

WARNING

To avoid serious personal injury

caused by entrapment, always con-

form to the following instructions

without exception.

. When operating the power win-

dows, be extremely careful to

prevent anyone’s body parts or

any other objects from being

caught in the window.

. Always lock the passengers’ win-

dows using the lock switch when

children are riding in the vehicle.

. Always carry the key when you

leave the vehicle for safety rea-

sons and never allow an unat-

tended child to remain in the

vehicle. Failure to follow this

procedure could result in injury

to a child operating the power

window.

NOTE

. If the power window system detects

resistance, an impact or abnormality,

the window operation may be automa-

tically stopped to prevent further jam-

ming, entrapment or malfunction.

– The closing window slides down

slightly and stops.

– The opening window stops slid-

ing down.

. The power window system may

detect resistance, an impact or an

abnormality in the following cases.

– A substantial sized object is

caught between the window and

the window frame.

– A foreign object is caught be-

tween the window and the window

frame.

– The vehicle drives over a deep

pothole.

. The window cannot be closed for a

few seconds after the window is auto-

matically stopped by the system.

Keys and doors/Child safety locks

2-28

(133,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

& Power window operation

S02AH07

! Power window switches

S02AH0701

. Driver’s side power window switches:

1) For front left window (with one-touch auto

up and down feature)

2) For front right window (with one-touch

auto up and down feature)

3) For rear left window

4) For rear right window

5) Lock switch

All door windows can be controlled by the

power window switch cluster at the driver

side door.

The switch illuminates when activated.

. Passenger’s side power window

switches:

Each passenger’s window can be con-

trolled by the power window switch located

on the door.

The switch illuminates when activated.

! Operating the window

S02AH0702

. With one-touch auto up and down

feature:

1) Automatically close*

2) Close

3) Open

4) Automatically open*

*: To stop the window halfway, operate the

switch to opposite side.

– CONTINUED –

Keys and doors/Windows

2-29

(134,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

. Without one-touch auto up and down

feature:

1) Close

2) Open

NOTE

Avoid the following.

. Continuously operating a switch in

the same direction after the window is

fully closed or fully opened.

. Continuously operating three or

more switches all at once in the same

direction after the windows are fully

closed or fully opened.

Either of the operations described

above may cause the power window

breaker to operate making it impossible

to open or close the window. Be sure to

initialize the power windows. If they are

not initialized, the one-touch auto up/

down function will not operate. Refer to

“Initialization of power window with

one-touch auto up/down function”

F2-31.

! Anti-entrapment function (windows

with one-touch auto up/down func-

tion)

S02AH0703

While closing the window automatically, if

the window senses a substantial enough

object trapped between the window and

the window frame, it automatically moves

down slightly and stops.

If a foreign object is caught while the

window is opening automatically, the

window will stop.

CAUTION

. Never attempt to test the power

window operation using body

parts.

. The anti-entrapment function

may not operate properly if some

object gets trapped just before

the window fully closes.

NOTE

. If a window detects an impact similar

to that caused by trapping an object (for

example, when the vehicle encounters

a deep pothole), the anti-entrapment

function may operate.

. The window cannot be operated for a

few seconds after the anti-entrapment

function operates.

! Off delay function (windows with

one-touch auto up/down function)

S02AH0705

The windows can be operated for approxi-

mately 40 seconds even after the ignition

switch is turned to the “ACC” or “OFF”

position. If a front door is opened within 40

seconds, the off delay function is can-

celed.

! Locking the passengers’ windows

S02AH0704

1) Lock

2) Unlock

When the lock switch is in the lock position,

the rear windows cannot be operated by

Keys and doors/Windows

2-30

(135,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

the driver’s side switches. The passen-

ger’s side switches and the rear seat side

switches are not operational either.

When the indicator on the window

switches does not illuminate, the window

switch cannot be operated.

& Initialization of power window

with one-touch auto up/down

function

S02AH06

If the power window automatic function

(one-touch auto up and down function)

does not operate properly, operate each

window according to the following proce-

dure in order to initialize the power window

system.

1. Close the door.

2. Turn the ignition switch to the “ON”

position.

3. Open the window completely and then

press and hold down the power window

switch for approximately 1 second.

4. Close the window completely and then

pull and hold the power window switch for

approximately 1 second.

Rear gate

S02AJ

WARNING

. To prevent dangerous exhaust

gas from entering the vehicle,

always keep the rear gate closed

while the engine is running.

. Do not attempt to shut the rear

gate while holding the recessed

grip. Also avoid closing the rear

gate by pulling on the recessed

grip from inside the cargo space.

There is a danger of your hand

being caught and injured.

NOTE

If the rear gate cannot be unlocked due

to a discharged vehicle battery, a mal-

function in the door locking/unlocking

system or other causes, the rear gate

can be unlocked by manually operating

the rear gate lock release lever.

For the procedure, refer to “Rear gate –

if the rear gate cannot be opened” F9-

19.

& Lock/unlock

S02AJ02

The rear gate can be locked and unlocked

using any of the following systems.

. Power door locking switch: Refer to

“How to operate the power door locking

switches” F2-23.

. Keyless access with the push-button

start system (if equipped): Refer to “Key-

less access with push-button start system”

F2-2.

. Remote keyless entry system: Refer to

“Remote keyless entry system” F2-17.

. Automatic door locking/unlocking: Re-

fer to “Automatic door locking/unlocking”

F2-23.

& Open/close

S02AJ03

1) The rear gate opener button

– CONTINUED –

Keys and doors/Rear gate

2-31

(136,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

To open:

First unlock the rear gate lock then push

the rear gate opener button.

To close:

Lower the rear gate slowly and push down

firmly until the latch engages.

The rear gate can be lowered easily if you

pull it down holding the recessed grip.

CAUTION

. Do not jam a plastic bag in or

place cellophane tape on the rear

gate stays or scratch the stays

while loading or unloading cargo.

Doing so could cause leakage of

gas from the stays, which may

result in their inability to hold the

rear gate open.

. Be careful not to hit your head or

face on the rear gate when open-

ing or closing the rear gate and

when loading or unloading cargo.

Moonroof (if equipped)

S02AK

WARNING

Never let anyone’s hands, arms,

head or any objects protrude from

the moonroof. A person could be

seriously injured if any of the follow-

ing conditions occur.

. The vehicle stops suddenly.

. The vehicle turns sharply.

. The vehicle is involved in an

accident.

. Body parts protruding from the

vehicle are struck by outside

objects.

To avoid serious personal injury

caused by entrapment, always con-

form to the following instructions

without exception.

. Before closing the moonroof,

make sure that no one’s hands,

arms, head or other objects will

be accidentally caught in the

moonroof.

. Always carry the key when you

leave the vehicle for safety rea-

sons and never allow an unat-

tended child to remain in the

Keys and doors/Moonroof

2-32

(137,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

vehicle. Failure to follow this

procedure could result in injury

to a child operating the moon-

roof.

. Never try to check the anti-en-

trapment function by deliberately

placing part of your body in the

moonroof.

CAUTION

. Do not sit on the edge of the open

moonroof.

. Do not operate the moonroof if

falling snow or extremely cold

conditions have caused it to

freeze shut.

. The anti-entrapment function

does not operate when the moon-

roof is being tilted down. Be sure

to confirm that it is safe to do so

before tilting the moonroof down.

. If the moonroof does not close,

have the system checked by a

SUBARU dealer.

The moonroof has both tilting and sliding

functions.

The moonroof operates only when the

ignition switch is in the “ON” position.

& Moonroof switches

S02AK02

! Tilting moonroof

S02AK0201

1) Up

2) Down

To raise the moonroof, press and hold the

switch in the up side and release. To lower

the moonroof, press and hold the switch in

the down side.

NOTE

Release the switch after the moonroof

has been raised or has been lowered

completely. Pressing the switch con-

tinuously may cause damage to the

moonroof.

! Sliding moonroof

S02AK0202

1) Open

2) Close

To open or close the moonroof using the

automatic function, press and hold the

switch toward the open/close side and

release.

To stop the moonroof halfway, press a

switch on the moonroof switch.

NOTE

. After washing the vehicle or after it

rains, wipe away water on the roof prior

to opening the moonroof to prevent

drops of water from falling into the

passenger compartment.

– CONTINUED –

Keys and doors/Moonroof

2-33

(138,1)

北米Model "A1410BE-B" EDITED: 2020/ 9/ 16

. For the sake of safety, it is recom-

mended that you avoid driving with the

moonroof fully opened.

! Anti-entrapment function

S02AK0203

When the moonroof senses a substantial

enough object trapped between its glass

and the vehicle’s roof during closure, it

automatically moves back to the fully open

position and stops there. The anti-entrap-

ment function may also be activated by a

strong shock on the moonroof even when

there is nothing trapped.

CAUTION

Never attempt to test this function

using fingers, hands or other parts

of your body.

& Sunshade

S02AK05

The sunshade can be slid forward or

backward by hand while the moonroof is

closed.

If the moonroof is opened, the sunshade

also moves back.

Keys and doors/Moonroof

2-34

Keys for Your Subaru XV SUV Third Generation (2022-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals