Get Inspection and Maintenance -> Bulb replacement Guide for Suzuki Baleno 4 Door First Generation (1995-2002)

7-50

INSPECTION AND MAINTENANCE

68PM2-01E

Bulb replacement

Headlights

Discharge headlights

Since special procedures are required, we

recommend you take your vehicle to your

SUZUKI dealer for bulb replacement.

Halogen headlights

68PM00714

(1) Headlight (high/low beam)

68PM00715

Open the engine food. Disconnect the cou-

pler (2). Remove the sealing rubber (3).

Push the retaining spring (4) forward and

unhook it. Then remove the bulb. Install a

new bulb in the reverse order of removal.

CAUTION

• Light bulbs can be hot enough to

burn your finger right after turning

off lights. This is true especially for

halogen headlight bulbs. Replace

the bulbs after they become cool

enough.

• The headlight bulbs are filled with

pressurized halogen gas. They can

burst and injure you if they are hit

or dropped. Handle them carefully.

• To avoid injury by sharp-edged

parts of the body, wear gloves and

a long-sleeved shirt when replacing

light bulbs.

NOTICE

The oils from your skin may cause a

halogen bulb to overheat and burst

when the lights are on. Grasp a new

bulb with a clean cloth.

NOTICE

Frequent bulb replacement indicates

the need for an inspection of the elec-

trical system. This should be carried

out by your SUZUKI dealer.

WARNING

Never attempt to replace the bulb of a

discharge headlight, or you could

suffer an electric shock from the

high-voltage circuit in the headlight

system. Always have a discharge

headlight bulb replaced by an autho-

rized SUZUKI dealer.

(1)

(3)

(2)

(4)

7-51

INSPECTION AND MAINTENANCE

68PM2-01E

68PM00716

NOTE:

You can see the position of retaining spring

from the hole of headlight.

Side turn signal light (on fender)

(if equipped)

68PM00736

1) Remove the light housing (1) by sliding

to left with your finger.

68PM00717

2) Turn the bulb holder (2) clockwise and

pull it out from the light housing.

(1)

(2)

7-52

INSPECTION AND MAINTENANCE

68PM2-01E

68PM00718

(4) Removal

(5) Install

3) To remove and install the bulb of the

side turn signal light (3), simply pull out

or push in the bulb.

Front turn signal light and

front position light

Vehicle with the halogen headlights

68PM00719

(1) Front turn signal light

(2) Front position light

Vehicle with the discharge headlights

68PM00720

(1) Front turn signal light

(3)

(4)

(5)

EXAMPLE

(1)

(2)

(1)

7-53

INSPECTION AND MAINTENANCE

68PM2-01E

68PH00732

1) Open the engine hood. To remove the

bulb holder of the front turn signal light

or the front position light from the light

housing, turn the holder counterclock-

wise and pull it out.

68PM00721

(3) Removal

(4) Installation

2) To remove the bulb of the front turn sig-

nal light (1) from the bulb holder, push

in the bulb and turn it counterclockwise.

To install a new bulb, push it in and turn

it clockwise.

To remove and install the bulb of the

front position light (2), simply pull out or

push in the bulb.

Front fog light (if equipped)

1) Start the engine. Turn the steering

wheel to the opposite side of the fog

light to be replaced to replace the bulb

easily. Then turn off the engine.

68PM00722

2) Remove the clips (1).

EXAMPLE

(1)

(2)

(3)

(4)

EXAMPLE

(1)

EXAMPLE

7-54

INSPECTION AND MAINTENANCE

68PM2-01E

68PM00723

3) Open the end of the cover inside the

fender.

80JM071

4) Disconnect the coupler by pushing the

lock release. Turn the bulb holder coun-

terclockwise and remove it.

Rear combination light

68PM00724

1) Remove the bolts (1) and pull the light

housing (2) straight.

EXAMPLE

(1)

(2)

7-55

INSPECTION AND MAINTENANCE

68PM2-01E

68PM00725

2) Remove the wire (3) from a clamp (4).

68PM00726

3) To remove the bulb holder of the rear

turn signal light (5), the rear fog light (6)

or the reversing light (7) from the light

housing, turn the holder counterclock-

wise and pull it out.

68PM00727

(8) Removal

(9) Installation

4) To remove the bulb of the rear turn sig-

nal light (5) or the rear fog light (6) from

the bulb holder, push in the bulb and

turn it counterclockwise. To install a

new bulb, push it in and turn it clock-

wise.

To remove and install the bulb of the

reversing light (7), simply pull out or

push in the bulb.

(4)

(3)

(7)

(6)

(5)

(5) / (6)

(7)

(8)

(9)

EXAMPLE

7-56

INSPECTION AND MAINTENANCE

68PM2-01E

68PM00735

5) Replace cushion pad (10) with a new

one. When sticking the cushion pad,

carefully position it not to cross the

boundary line (11).

NOTE:

Cushion pad cannot be reused. When

removing the light housing, replacing the

cushion pad is necessary.

To purchase it, see your SUZUKI dealer.

68PM00728

NOTE:

When reinstalling the light housing, check

that the clips are properly attached.

License plate light

76MH0A125

1) Turn the cover (1) counterclockwise to

remove it.

(10)

(11)

Type A

Type B

(1)

7-57

INSPECTION AND MAINTENANCE

68PM2-01E

76MH0A126

2) To remove and install the bulb of the

license plate light (2), simply pull out or

push in the bulb.

Interior light

Remove the lens by using a flat-bladed

screwdriver covered with a soft cloth as

shown. To install it, simply push it back in.

Front

61MM0A207

Center

60G115

Luggage compartment (if equipped)

68PM00729

(2)

Inspection and Maintenance -> Bulb replacement for Your Suzuki Baleno 4 Door First Generation (1995-2002)

Related Topics

Popular Owner Manuals

Latest Owner Manuals