2000-2008 Suzuki Ignis SUV Before Driving -> Information display (instrument cluster without tachometer) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Before Driving -> Information display (instrument cluster without tachometer) for Your Suzuki Ignis SUV First Generation (2000-2008)

2-66
BEFORE DRIVING
Information display
(Instrument cluster without
tachometer)
75RM250
(1) Trip meter selector knob
(2) Indicator selector knob
66RH117
(3) Information display
When the ignition switch is in “ON” posi-
tion, the information display shows the fol-
lowing information.
Display (A)
Fuel gauge
Display (B)
Gearshift indicator
Display (C)
Trip meter / Odometer / Fuel consumption /
Driving range
Display (D)
Clock
Fuel gauge
The display (A) shows the fuel gauge.
Refer to “Fuel gauge” in this section.
Gearshift indicator
The display (B) shows the gearshift indica-
tor.
Refer to “Gearshift indicator” in the
“OPERATING YOUR VEHICLE” section.
(1) (2)
EXAMPLE
(3)
(A) (B) (C)
(D)
EXAMPLE
2-67
BEFORE DRIVING
Trip meter / Odometer /
Fuel consumption / Driving range
The display (C) shows one of the following
indications, trip meter A, trip meter B,
odometer, instantaneous fuel consump-
tion, average fuel consumption or driving
range.
To switch the display indication (C), push
the trip meter selector knob (1) or the indi-
cator selector knob (2) quickly.
75RM368
(a) Trip meter A
(b) Trip meter B
(c) Odometer
(d) Instantaneous fuel consumption
(e) Average fuel consumption
(f) Driving range
NOTE:
• Indications will change when you push
and release a knob.
• The display shows estimated values.
Indications may not be the same as
actual values.
Trip meter
The trip meter can be used to measure the
distance traveled on short trips or between
fuel stops.
You can use the trip meter A or trip meter B
independently.
To reset the trip meter to zero, push and
hold the trip meter selector knob (1) for a
while when the display shows the trip
meter.
Push the trip meter selector
knob (1).
Push the indicator selector
knob (2).
(a)
(b)
(c)
(d)
(e)
(f)
(
a
)
(
b
)
(
c
)
(
d
)
(
e
)
(
f
)
EXAMPLE
WARNING
If you attempt to adjust the display
while driving, you could lose control
of the vehicle.
Do not attempt to adjust the display
while driving.
2-68
BEFORE DRIVING
NOTE:
The indicated maximum value of the trip
meter is 9999.9. When you run past the
maximum value, the indicated value will
return to 0.0.
Odometer
The odometer records the total distance
the vehicle has been driven.
Instantaneous fuel consumption
The display shows the value of instanta-
neous fuel consumption only when the
vehicle is moving.
NOTE:
• The display does not show the value
unless the vehicle is moving.
• Depending on the vehicle’s specification,
the fuel consumption units of initial set-
ting are indicated as L/100km or km/L.
• The indicated maximum value of instan-
taneous fuel consumption is one of the
followings. No more than the maximum
value will be indicated on the display
even if the actual instantaneous fuel
consumption is higher.
– For L/100km setting: 30
– For km/L setting: 50
• The indication on the display may be
delayed if fuel consumption is greatly
affected by driving conditions.
• The display shows estimated values.
Indications may not be the same as
actual values.
• For “L/100km” or “km/L” setting, you can
change the units that instantaneous fuel
consumption is displayed in. Refer to
“Average fuel consumption” in this sec-
tion.
Average fuel consumption
If you selected average fuel consumption
the last time you drove the vehicle, the dis-
play shows the last value of average fuel
consumption from previous driving when
the ignition switch is turned to “ON” posi-
tion. Unless you reset the value of average
fuel consumption, the display indicates the
value of average fuel consumption which
includes average fuel consumption during
previous driving.
To reset the average fuel consumption to
zero, push and hold the indicator selector
knob (2) for a while when the display
shows the average fuel consumption.
NOTE:
When you reset the indication or reconnect
the negative (–) terminal to the battery, the
value of average fuel consumption will be
shown after driving for a while.
(For “L/100km” or “km/L” setting)
To change the unit of average fuel con-
sumption, while pushing and holding the
trip meter selector knob (1), turn the indica-
tor selector knob (2).
68PH02207
NOTE:
• When you change the units that average
fuel consumption is displayed in, the
instantaneous fuel consumption units will
be changed automatically.
• When you reconnect the negative (–)
terminal to the battery, the unit of the
average fuel consumption will be reini-
tialized. Change the unit again to your
preference.
NOTICE
Keep track of your odometer reading
and check the maintenance sched-
ule regularly for required services.
Increased wear or damage to certain
parts can result from failure to per-
form required services at the proper
mileage intervals.
EXAMPLE
(Initial setting)
2-69
BEFORE DRIVING
Driving range
If you selected driving range the last time
you drove the vehicle, the display indicates
“---” for a few seconds and then indicates
the current driving range when the ignition
switch is turned to “ON” position.
The driving range shown in the display is
the approximate distance you can drive
until the fuel gauge indicates “E”, based on
current driving conditions.
When the low fuel warning light comes on,
the display “---” will appear.
If the low fuel warning light comes on, fill
the fuel tank immediately regardless of the
value of driving range shown in the display.
As the driving range after refueling is cal-
culated based on the most recent driving
condition, the value is different each time
you refuel.
NOTE:
• If you refuel when the ignition switch is in
“ON” position, the driving range may not
indicate the correct value.
• When you reconnect the negative (–)
terminal to the battery, the value of driv-
ing range will be shown after driving for a
while.
Clock
The display (D) shows the time.
To change the time indication:
1) Push the trip meter selector knob (1)
and the indicator selector knob (2)
together.
2) To change the hour indication, turn the
indicator selector knob (2) left or right
repeatedly when the hour indication
blinks. To change the hour indication
quickly, turn and hold the indicator
selector knob (2). To set the hour indi-
cation, push the indicator selector knob
(2) and the minute indication will blink.
3) To change the minute indication, turn
the indicator selector knob (2) left or
right repeatedly when the minute indi-
cation blinks. To change the minute
indication quickly, turn and hold the
indicator selector knob (2). To set the
minute indication, push the indicator
selector knob (2).
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the clock indication will
be reinitialized. Change the indication
again to your preference.
WARNING
If you attempt to adjust the display
while driving, you could lose control
of the vehicle.
Do not attempt to adjust the display
while driving.
2-70
BEFORE DRIVING
Setting mode
In the setting mode, you can set up the following functions.
Indication Functions
Time indication of clock “ ”
Central door locking system “ ”
Automatic door locking function “ ”
Automatic door unlocking function “ ”
Additional flashes of the turn signal “ ”
Initialization setting “ ”
Exit the setting mode “ ”
2-71
BEFORE DRIVING
NOTE:
Depending on vehicle’s specifications,
some items may not be displayed.
How to operate the setting mode:
1) When the ignition switch is in “ON”
position and the vehicle is stationary,
push the trip meter selector knob (1) to
switch the information display indication
(C) to the odometer.
2) Push and hold the indicator selector
knob (2) until the display shows
“ ”.
3) Turn and/or push the indicator selector
knob (2) to select a function that you
want to set up according to the above
chart.
4) Turn and/or push the indicator selector
knob (2) to register settings of the fol-
lowing functions.
Time indication of clock “ ”
• : 12-hour format (default set-
ting)
• : 24-hour format
Central door locking system “ ”
• : Unlock all doors by turning
the key once
• : Unlock all doors by turning
the key twice (default setting)
Automatic door locking function “ ”
• : Disable the automatic door
locking function
• : Lock all doors when the vehi-
cle speed reaches 15 km/h
(default setting)
Automatic door unlocking function “ ”
• : Disable the automatic door
unlocking function
• : Unlock all doors when the key
is pulled out from the ignition
switch (default setting)
Additional flashes of the turn signal “ ”
• : Turn signal flashes three
times after the turn signal
lever is returned (default set-
ting)
• : Disable the additional flashes
of turn signal
Initialization setting “ ”
• : Initialize all settings
75RM229
NOTE:
• As shown in the above illustration, “ ”
indicates on the display of currently set-
ting item.
• To go back to the higher level display
during operation, turn the indicator
selector knob (2) to display “ ” or
“ ” and then push the indicator
selector knob (2).
5) To exit the setting mode, switch the dis-
play to show “ ” and then push the
indicator selector knob (2).
Turn the indicator selector knob
(2).
Push the indicator selector
knob (2).
EXAMPLE

Related Topics

Before Driving
Keys Door locks Keyless push start system remote controller / Keyless entry system transmitter (if equipped) Security system (if equipped) Windows Mirrors Front seats Rear seats Seat belts and child restraint systems Supplemental restraint system (air bags) Instrument cluster Speedometer Tachometer (if equipped) Fuel gauge Brightness control Information display (instrument cluster with tachometer) Warning and indicator lights Lighting control lever Front fog light switch (if equipped) Headlight leveling switch Turn signal control lever Hazard warning switch Windshield wiper and washer lever Tilt steering lock lever Horn Heated rear window switch (if equipped)

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot