2000-2008 Suzuki Ignis SUV Before Driving -> Security system (if equipped) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Before Driving -> Security system (if equipped) for Your Suzuki Ignis SUV First Generation (2000-2008)

2-15
BEFORE DRIVING
Security system (if equipped)
The security system is armed in about 5
seconds after you lock all doors (including
the tailgate) by using the keyless entry sys-
tem transmitter, keyless push start system
remote controller or request switch.
Once the system is armed, any attempt to
open a door by using any other means (*)
than the keyless entry system transmitter,
keyless push start system remote control-
ler or request switch, or open the engine
hood, will cause the alarm to be triggered.
* These means include the following:
– The key
– The lock knob on a door
– The central door locking switch
– The tailgate emergency lever
Also, in case that you have set the shock
sensor to enabled state and set sensitivity
of the pre-warning function and full blast
warning function to a level other than 0, the
alarm will be triggered if any attempt to
tamper with the vehicle. The shock sensor
can be selected enabled or disabled state,
and sensitivity of each warning can be
adjusted as desired. To set the shock sen-
sor, ask your authorised Maruti Suzuki
workshop or use the setting mode of the
information display.
NOTE:
• The default setting of the shock sensor
is in the disabled state. Set to the
enabled state and adjust sensitivity of
each warning according to your prefer-
ence. For details on how to use the infor-
mation display, refer to “Information
display” in this section.
• Your dealer may have already set the
shock sensor of the vehicle to the
enabled state before you purchase it.
Consult your dealer for further informa-
tion.
NOTE:
• The security system generates alarms
when any of the predetermined condi-
tions is met. However, the system does
not have any function of blocking unau-
thorized entry into the vehicle.
• Always use the keyless entry system
transmitter, keyless push start system
remote controller or request switch to
unlock the doors when the security system
has been armed. Using a key instead will
trigger the alarm.
• If a person who does not know the secu-
rity system is going to drive the vehicle,
we recommend you explain the system
and its operation to the person, or dis-
able the system beforehand. Mistakenly
triggering the alarm may cause a nui-
sance to others.
• Even if the security system is armed,
you should still be careful to guard
against theft. Do not leave money or
things of value in the vehicle.
How to arm the security system
(when enabled)
Lock all doors (including the tailgate) using
the keyless entry system transmitter, key-
less push start system remote controller or
request switch. The security system indica-
tor (1) will start blinking rapidly, and the
security system will be armed in about 5
seconds.
When the system is armed, the indicator
continues to blink at intervals of approxi-
mately 2 seconds.
62R0148
(1)
EXAMPLE
2-16
BEFORE DRIVING
NOTE:
• To prevent the alarm from being acci-
dentally triggered, avoid arming it while
anyone remains inside the vehicle. The
alarm will be triggered if any person
inside opens the door, tailgate, engine
hood, or swings the vehicle (if the shock
sensor is in the enabled state).
• The security system is not armed when
all doors are locked using the key from
outside, using the door lock knobs or the
central door locking switch from inside.
• If any door is not operated within approx-
imately 30 seconds after the doors have
been unlocked using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the doors are automatically
locked again. When the doors are
locked, the security system will be
armed in about 5 seconds if the system
is in the enabled state.
• If the security system indicator (1) blinks
when the ignition switch is in “ON” posi-
tion or the ignition mode is ON, there
may be something wrong with the secu-
rity system. Ask your authorised Maruti
Suzuki workshop to inspect the system.
How to disarm the security system
Simply unlock the doors using the keyless
push start system remote controller, the
request switch or the keyless entry system
transmitter. The security system indicator
will go out, indicating that the security sys-
tem is disarmed.
How to stop the alarm
Should the alarm be triggered accidentally,
the alarm will stop by the following opera-
tions.
• Press the engine switch to change the
ignition mode to ON or turn the ignition
switch to “ON” position.
• Unlock the doors using the keyless push
start system remote controller, the
request switch, or the keyless entry sys-
tem transmitter.
NOTE:
• Even after the alarm has stopped, if you
lock the doors using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the security system will be
rearmed with a delay of about 5 sec-
onds.
• If you disconnect the battery while the
security system is in the armed condition
or the alarm is actually in operation, the
alarm will be re-triggered when the bat-
tery is then reconnected.
• Even after the alarm has stopped at the
end of the predetermined operation time,
it will be triggered again if any of the
doors, tailgate or engine hood is opened,
or the vehicle feels a shock (if the shock
sensor is in the enabled state), without
disarming the security system.
Checking whether the alarm has been
triggered during parking
If the alarm was triggered and you then
turn the ignition switch to “ON” position or
change the ignition mode to ON, the secu-
rity system indicator will blink rapidly for
about 8 seconds and a buzzer will beep 4
times during this period. If this happens,
check whether the vehicle has been bro-
ken into while you were away from it.
Enabling and disabling the security
system
The security system can be either enabled
or disabled.
When enabled
• If any of the doors or tailgate are opened
without unlocking by the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, all turn signal lights start to blink
and the interior buzzer beeps intermit-
tently. After 5 seconds, the siren will
sound for about 27.5 seconds. The
security system indicator continues to
blink during this time.
• If the engine hood is opened, all turn sig-
nal lights blink, and the siren sounds for
about 27.5 seconds. The security sys-
tem indicator continues to blink during
this time.
2-17
BEFORE DRIVING
(If the shock sensor is in the enabled state)
• If the vehicle feels a shock higher than
the pre-warning sensitivity, the siren
sounds for about 2 seconds (pre-warn-
ing). If the vehicle feel a shock higher
than the full blast warning sensitivity, all
turn signal lights start to blink and the
interior buzzer beeps intermittently. After
5 seconds, the siren will sound for about
27.5 seconds (full blast warning). The
security system indicator continues to
blink during this time.
NOTE:
If you set the full blast warning sensitivity
higher than the pre-warning sensitivity in
the setting mode of the information display,
or the vehicle feels such shock as to be
able to trigger the full blast warning, the full
blast warning will be triggered preferen-
tially. In this case, the pre-warning will not
be triggered.
When disabled
When the system is disabled, it stays dis-
armed even if you perform any system
arming operation.
How to switch the state of the security
system
When the security system has been
already disarmed, you can switch the sys-
tem from the enabled state to the disabled
state, and vice versa, using the following
method.
1) Sit in the driver’s seat and make sure
that all doors, tailgate and engine hood
are closed.
• If any door is open, the open door
warning light comes on.
75RM263
2) Turn the lock knob (1) on the driver’s
door rearward (2).
66RH015
3) Turn the knob on the lighting control
lever to the OFF position (3).
NOTE:
The following steps 4) and 5) must be
completed within 15 seconds.
66RH016
(1)
(2)
EXAMPLE
(3)
EXAMPLE
OFF
4 times
EXAMPLE
2-18
BEFORE DRIVING
4) Turn the knob on the lighting control
lever to the position and then turn
back to the OFF position. Repeat this
operation 4 times.
66RH017
5) Push the lock end (4) (forward end) of
the central door locking switch (5), and
then push the unlock end (6) (backward
end). Repeat this operation 3 times.
Every time you perform the series of the
above steps, the state of the security sys-
tem changes from the currently selected
one to the other. You can check whether
the system is enabled or disabled by the
number of interior buzzer beeps at the end
of the procedure as follows.
• If you cannot complete the operations in
step 4) and 5) within 15 seconds cor-
rectly, the state of the security system
will not change and the interior buzzer
does not beep. Perform the procedure
again from the beginning.
NOTE:
You can also switch the security system
from the enabled state to the disabled
state, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information display” in this section.
Windows
Manual window control
(if equipped)
60G010A
Raise or lower the door windows by turning
the handle located on the door panel.
(5)
(4)
(6)
EXAMPLE
3 times
System state Number of beeps
Disabled
(Mode A)
Once
Enabled
(Mode D)
4 times
EXAMPLE

Related Topics

Popular Owner Manuals