Get CONTROLS -> Operating state of the vehicle Guide for Toyota Supra 2 Door Fifth Generation (2020-2025)

40

3-1. CONTROLS

to opening from the outside and

after exiting and locking.

Operating state of the

vehicle

Automatic idle state

Vehicle features and

options

The idle state is automatically

established under the following

conditions:

• After several minutes, if no

operation takes place on the

vehicle.

This chapter describes all stan-

dard, country-specific and

optional features offered with

the series. It also describes fea-

tures and functions that are not

necessarily available in your

vehicle, e.g., due to the selected

options or country versions. This

also applies to safety-related

functions and systems. When

using these functions and sys-

tems, the applicable laws and

regulations must be observed.

• If the charge state of the vehi-

cle battery is low.

• Depending on the setting via

Toyota Supra Command, if

one of the front doors is

opened when exiting the vehi-

cle.

The idle state is not automati-

cally established while a phone

call is active.

General information

Depending on the situation, the

vehicle is in one of the three

states:

Establishing idle state

when opening the front

doors

• Idle state.

• Standby state.

• Drive-ready state.

Via Toyota Supra Command:

1 "My Vehicle"

2 "Vehicle settings"

3 "Doors/Key"

4 "Turn off after door opening"

Idle state

Concept

Manual idle state

If the vehicle is in idle state, it is

switched off. All power consum-

ers are deactivated.

To establish idle state in the

vehicle after end of trip:

General information

The vehicle is in idle state prior

Supra Owner's Manual_U (from Jul. '20 Prod.)

41

3-1. CONTROLS

Drive-ready state

Concept

Switching on drive-ready state

corresponds to starting the

engine.

Press and hold the

button until the

OFF indicator on

the instrument

General information

Some functions, such as VSC

Vehicle Stability Control System,

can only be used with

cluster goes out.

3

drive-ready state switched on.

Standby state

Safety information

WARNING

Concept

When standby state is switched

on, most functions can be used

while the vehicle is stationary.

Desired settings can be

adjusted.

If the exhaust pipe is blocked or

ventilation is insufficient, harmful

exhaust gases can enter into the

vehicle. The exhaust gases con-

tain pollutants which are colorless

and odorless. In enclosed areas,

exhaust gases can also accumu-

late outside of the vehicle. There

is danger to life. Keep the exhaust

pipe free and ensure sufficient

ventilation.

General information

The vehicle is in the standby

state after the front doors are

opened from the outside.

WARNING

An unsecured vehicle can begin

to move and possibly roll away.

There is a risk of an accident.

Before exiting, secure the vehicle

against rolling.

Display in the instrument

cluster

OFF is displayed

in the instrument

cluster. The drive-

train is switched off

and standby state

switched on.

In order to ensure that the vehicle

is secured against rolling away,

follow the following:

• Set the parking brake.

Supra Owner's Manual_U (from Jul. '20 Prod.)

42

3-1. CONTROLS

WARNING

Gasoline engine

• On uphill grades or on a down-

hill slope, turn the front wheels

in the direction of the curb.

Depending on the engine condi-

tion, the full drive power may not

be available for approximately

30 seconds after starting the

engine. In this case, the vehicle

will not accelerate as usual.

• On uphill grades or on a down-

hill slope, also secure the vehi-

cle, for instance with a wheel

chock.

NOTICE

Display in the instrument

cluster

In the case of repeated starting

attempts or repeated starting in

quick succession, the fuel is not

burned or is inadequately burned.

The catalytic converter can over-

heat. There is a risk of damage to

property. Avoid repeated starting

in quick succession.

When drive-ready state is

switched on, the tachometer

shows the current engine

speed.

Switching off drive-ready

state

Switching on drive-ready

state

1 Engage selector lever posi-

tion P with the vehicle

stopped.

Concept

Drive-ready state

is switched on via

the Start/Stop but-

ton:

2 Press the Start/Stop button.

The engine is switched off. The

vehicle switches into standby state.

3 Set the parking brake.

Automatic transmission

1 Depress the brake pedal.

2 Press the Start/Stop button.

The ignition is activated auto-

matically for a brief time and is

stopped as soon as the engine

starts.

Most of the indicator/warning

lights in the instrument cluster

light up for a varied length of

time.

Supra Owner's Manual_U (from Jul. '20 Prod.)

CONTROLS -> Operating state of the vehicle for Your Toyota Supra 2 Door Fifth Generation (2020-2025)

Related Topics

CONTROLS

Popular Owner Manuals

Latest Owner Manuals