Get Driving and operating -> Driver assistance systems Guide for Vauxhall Crossland SUV First Generation (2020-2024)

140

Driving and operating

ESC and traction control system are

also reactivated the next time the

ignition is switched on.

Additionally position D or the second

or a higher gear in position M must be

selected on automatic transmission.

Deviations from the stored speeds

may occur when driving uphill or

downhill.

The system maintains the vehicle

speed at the preset speed by the

driver, without any action on the

accelerator pedal.

The preset speed can be exceeded

temporarily by pressing the

accelerator pedal firmly.

The status and preset speed is

displayed in the Driver Information

Centre.

Do not use the cruise control if it is not

advisable to maintain a constant

speed.

Driver assistance

systems

Fault

9 Warning

If there is a fault in the system, the

control indicator b illuminates

continuously and a message appears

in the Driver Information Centre. The

system is not operational.

Have the cause of the fault remedied

by a workshop.

Driver assistance systems are

developed to support the driver

and not to replace the driver's

attention.

The driver stays in full control of

the vehicle and accepts full

responsibility when driving the

vehicle.

When using driver assistance

systems, always take care

regarding the current traffic

situation and follow applicable

traffic rules.

Control indicator m 3 88.

Cruise control

The cruise control can store and

maintain speeds above 25 mph.

Additionally at least the third gear

must be engaged on manual

transmission.

Driving and operating

141

Accelerate to the desired speed and

move thumb wheel briefly to SET/-.

The current speed is stored and

maintained. Accelerator pedal can be

released.

Switching on the system

The preset speed can then be

changed by moving thumb wheel to

RES/+ to increase or to SET/- to

decrease the speed. Move thumb

wheel repeatedly to change speed in

small steps, move and hold to change

speed in large steps.

Activation of the functionality

Setting speed by the driver

Press m on the steering wheel:

symbol m and a message are

indicated in the Driver Information

Centre. The system is still not active.

Speed value is indicated in the Driver

Information Centre.

142

Driving and operating

Adopting speed by the speed limit

recognition

Press MEM on the steering wheel

once more to confirm and save the

new speed setting.

This speed is the new value for the

cruise control.

This function can be deactivated or

activated in the personalisation menu

3 96.

Cruise control is deactivated

automatically when:

The intelligent speed adaptation

informs the driver when a speed limit

is detected by the speed limit

recognition. The detected speed limit

can be used as new value for the

cruise control.

●

The brake pedal is depressed.

Vehicle speed is below 25 mph.

The Traction Control system or

Electronic Stability Control is

operating.

●

The manual transmission is in N,

Using the camera at the top of the

windscreen, this system detects and

reads speed limit and end of speed

limit signs.

first or second gear.

Exceeding the set speed

The automatic transmission is in

position M and first gear.

Vehicle speed can be increased by

depressing the accelerator pedal.

When the accelerator pedal is

released, the previously stored speed

is resumed.

If the cruise control is active:

Resume stored speed

Move thumb wheel to RES/+ at a

speed above 25 mph. The stored

speed will be obtained.

●

in the uplevel Driver Information

Centre the recognised speed

limit will be displayed and MEM

illuminates.

Deactivation of the functionality

●

in the midlevel Driver Information

Centre the recognised speed

limit will be displayed on the

digital speed indication page

along with an instruction

message.

Press Ñ: cruise control is in pause

mode and a message is displayed.

The vehicle is driven without cruise

control.

Cruise control is deactivated, but not

switched off. Last stored speed

remains in memory for later speed

resume.

Switching off the system

Press m: the cruise control mode is

deselected and the cruise control

indication extinguishes in the Driver

Information Centre.

Pressing ß to activate the speed

limiter deactivates cruise control.

Press MEM on the steering wheel to

request saving of the suggested

speed.

Switching off the ignition cancels any

programmed speed value.

Driving and operating

143

Fault

Switching on the system

In the event of a cruise control fault,

the speed is cleared resulting in

flashing of the dashes.

The speed limit recognition may not

operate correctly if traffic signs do not

comply with the Vienna Convention

on Road Signs and Signals.

Speed limiter

The speed limiter prevents the

vehicle from exceeding a preset

maximum speed.

The maximum speed can be set at

speeds above 18 mph.

The driver can accelerate the vehicle

up to the preset speed. Deviations

from the limited speed may occur

when driving downhill.

Activation of the functionality

Setting speed by the driver

Press ß, symbol ß and a message

are displayed in the Driver

Information Centre. The system is still

not active.

The preset speed can be exceeded

temporarily by pressing the

accelerator pedal fully.

The status and preset speed limit is

displayed in the Driver Information

Centre.

144

Driving and operating

Accelerate to the desired speed and

move thumb wheel briefly to SET/-.

The current speed is stored as

maximum speed.

The preset maximum speed can be

changed by moving thumb wheel to

RES/+ to increase or to SET/- to

decrease the desired maximum

speed. Move thumb wheel repeatedly

to change speed in small steps, move

and hold to change speed in large

steps.

If the speed limiter is active:

●

in the uplevel Driver Information

Centre the recognised speed

limit will be displayed and MEM

illuminates.

●

in the midlevel Driver Information

Centre the recognised speed

limit will be displayed on the

digital speed indication page

along with an instruction

message.

Press MEM on the steering wheel to

request saving of the suggested

speed limit.

Press MEM on the steering wheel

once more to confirm and save the

new speed setting.

This speed is the new value for the

speed limiter.

This function can be deactivated or

activated in the personalisation menu

3 96.

Press Ñ to activate speed limiter.

Adopting speed by the speed limit

recognition

The intelligent speed adaptation

informs the driver when a speed limit

is detected by the speed limit

recognition. The detected speed limit

can be used as new value for the

speed limiter.

Speed value is indicated in the Driver

Information Centre.

Using the camera at the top of the

windscreen, this system detects and

reads speed limit and end of speed

limit signs.

Driving and operating

145

The forward collision alert uses the

front camera in the windscreen to

detect a preceding vehicle directly

ahead, in your path.

If a vehicle directly ahead is

approached too quickly, a warning

chime and alert in the Driver

Information Centre is provided.

Exceeding the speed limit

Switching off the system

In the event of an emergency, it is

possible to exceed the speed limit by

depressing the accelerator pedal

fully. In this case the preset speed

value flashes.

Press ß, the speed limiter mode is

deselected and the speed limit

indication extinguishes in the Driver

Information Centre.

Pressing m to activate cruise control

deactivates speed limiter.

The preset speed remains in the

memory when the ignition is switched

off.

Release the accelerator pedal and

the speed limiter function is

reactivated once a speed lower than

the limit speed is obtained.

9 Warning

Forward collision alert is just a

warning system and does not

apply the brakes. When

Deactivation of the functionality

Fault

Press Ñ, speed limiter is in pause

mode and a message is displayed.

The vehicle is driven without speed

limiter.

Speed limiter is deactivated, but not

switched off. Last stored speed

remains in memory for later speed

resume.

In the event of a speed limiter fault,

the speed is cleared resulting in

flashing of the dashes.

The speed limit recognition may not

operate correctly if traffic signs do not

comply with the Vienna Convention

on Road Signs and Signals.

approaching a vehicle ahead too

rapidly, it may not provide you

enough time to avoid a collision.

The driver accepts full

responsibility for the appropriate

following distance based on traffic,

weather and visibility conditions.

The complete attention of the

driver is always required while

driving. The driver must always be

ready to take action and apply the

brakes.

Resume limit speed

Press Ñ. The stored speed limit will

be obtained.

Forward collision alert

The forward collision alert may help to

avoid or reduce the harm caused by

front-end crashes.

146

Driving and operating

Activation

applicable traffic rules, weather

and road conditions etc. at all

times.

9 Warning

Forward collision alert detects

vehicles and operates automatically

at all speeds above 3 mph and

53 mph. The system detects

stationary vehicles if the speed does

not exceed 50 mph.

Forward collision alert is just a

warning system and does not

apply the brakes. When

approaching a vehicle ahead too

rapidly, it may not provide you

enough time to avoid a collision.

Selecting the alert sensitivity

The alert sensitivity has to be set to

close, normal or distant in the vehicle

personalisation menu 3 96.

Alerting the driver

The driver is warned by following

alerts:

The driver accepts full

The chosen setting will remain until it

is changed. The alert timing will vary

based on vehicle speed. The faster

the vehicle speed, the farther away

the alert will occur. Consider traffic

and weather conditions when

responsibility for the appropriate

following distance based on traffic,

weather and visibility conditions.

●

Symbol , illuminates and a

The complete attention of the

driver is always required while

driving. The driver must always be

ready to take action and apply the

brakes.

warning message is displayed in

the Driver Information Centre

when the distance to the vehicle

ahead gets to small.

selecting the alert timing.

Deactivation

●

Symbol , illuminates, a warning

The system can only be deactivated

by deactivating the active emergency

braking in the vehicle personalisation

3 96.

message is displayed in the

Driver Information Centre and a

warning chime sounds, when a

collision is imminent and

immediate driver's action is

required.

Caution

The colour lighting of this control

indicator does not correspond to

local traffic laws on following

distance. The driver bears full

responsibility for maintaining safe

following distance according to

System limitations

Forward collision alert is designed to

warn on vehicles only, but may react

also to other objects.

Driving and operating

147

In the following cases, forward

collision alert may not detect a vehicle

ahead or sensor performance is

limited:

Forward collision alert 3 145.

Front pedestrian protection 3 149.

The feature uses various inputs (e.g.

camera sensor, brake pressure,

vehicle speed) to calculate the

probability of a frontal collision.

Functionality

Active emergency braking is

equipped with a front camera and

operates in forward gear in the range

between walking speed and 53 mph.

The system detects stationary

vehicles only if the speed does not

exceed 50 mph.

●

driving on winding or hilly roads

driving in the dark

weather limits visibility, such as

fog, rain, or snow

9 Warning

A precondition is that forward collision

alert with front camera system is not

deactivated in the vehicle

●

the sensor in the windscreen is

blocked by snow, ice, slush, mud,

dirt etc.

the windscreen is damaged or

affected by foreign objects, e.g.

stickers

This system is not intended to

replace the driver responsibility for

driving the vehicle and looking

ahead. Its function is limited to

supplemental use only to reduce

the vehicle speed before a

collision.

The system may not react to

animals. After a sudden lane

change, the system needs a

certain time to detect the next

preceding vehicle.

personalisation menu 3 96.

The system includes:

●

emergency automatic braking

forward looking brake assist

forward collision alert

Active emergency braking

Active emergency braking can help to

reduce the damage and injury from

crashes with vehicles, pedestrians

and obstacles directly ahead, when a

collision can no longer be avoided

either by manual braking or by

steering. Before the active

front pedestrian protection

Emergency automatic braking

After activation of brake preparation

system and just before the imminent

collision, this function automatically

applies limited braking to reduce the

impact speed of the collision or

The driver must always be ready

to take action and apply the brakes

and steer to avoid collisions.

emergency braking applies, the driver

is warned by the forward collision

alert or the front pedestrian protection

alert.

prohibit a crash. If active emergency

braking is applied, m flashes in the

instrument cluster. Depending on the

148

Driving and operating

situation, the vehicle may

more sensitive. Therefore, pressing

the brake pedal less strongly results

in immediate hard braking. This

function helps the driver brake

quicker and harder before the

imminent collision.

Front pedestrian protection 3 149.

automatically brake moderately or

hard. This front automatic braking can

only occur if a vehicle or a pedestrian

ahead is detected.

System limitations

In some cases, the active emergency

braking system may provide an

automatic braking in situations that

seem to be unnecessary, for instance

in parking garages, due to traffic signs

in a curve or due to vehicles in

another lane. This is normal

operation, the vehicle does not need

service. Firmly apply the accelerator

pedal to override the automatic

braking if the situation and the

surroundings permit.

Forward collision alert 3 145.

Front pedestrian protection 3 149.

Emergency automatic braking may

slow the vehicle to a complete stop to

try to avoid a potential crash.

9 Warning

Active emergency braking is not

designed to apply hard

autonomous braking or to

automatically avoid a collision. It is

designed to reduce the vehicle

speed before a collision. It may not

react to animals. After a sudden

lane change, the system needs a

certain time to detect the next

preceding vehicle.

The complete attention of the

driver is always required while

driving. The driver must always be

ready to take action and apply the

brakes and steer to avoid

collisions.

9 Warning

Emergency automatic braking is

an emergency crash preparation

feature and is not designed to

avoid crashes. Do not rely on the

system to brake the vehicle.

Emergency automatic braking will

not brake outside of its operating

speed range and only responds to

detected vehicles and

In the following cases, active

emergency braking performance is

limited:

●

driving on winding or hilly roads

detecting all vehicles, especially

vehicles with a trailer, tractors,

muddy vehicles, etc.

pedestrians.

●

detecting a vehicle when weather

limits visibility, such as in fog,

rain, or snow

Forward looking brake assist

In addition to emergency automatic

braking, the forward looking brake

assist function makes the brake assist

The system is designed to work with

all occupants wearing their seat belts.

Forward collision alert 3 145.

●

driving in the dark

windscreen damaged or

stickered

Driving and operating

149

Complete attention is always required

while driving, and you should be

ready to take action and apply the

brakes and / or steer the vehicle to

avoid crashes.

We recommend to deactivate the

system in the vehicle personalisation

in the following cases:

illuminates in the instrument cluster

and a warning message is displayed

in the Driver Information Centre.

During driving in the dark, system

performance is limited.

9 Danger

Fault

Front pedestrian braking does not

provide an alert or automatically

brake the vehicle, unless it detects

a pedestrian.

The system may not detect

pedestrians, including children,

when the pedestrian is not directly

ahead, not fully visible, not

standing upright, or when part of a

group.

In case the system requires a service,

a message is displayed in the Driver

Information Centre.

If the system does not work as it

should do, vehicle messages are

displayed in the Driver Information

Centre.

●

when towing a trailer or caravan

when carrying long objects on

roof bars or a roof rack

●

when the vehicle is being towed

with the engine running

when a spare wheel is fitted that

is smaller than the other wheels

before using an automatic car

wash with the engine running

before placing the vehicle on a

rolling road in a workshop

if the windscreen has been

damaged close to the camera

if the front bumper has been

damaged

Vehicle messages 3 95.

Front pedestrian protection

Front pedestrian protection includes:

Front pedestrian protection may help

to avoid or reduce the harm caused

by front-end crashes with pedestrians

when driving forward.

●

detecting front pedestrian ahead

front pedestrian alert

Front pedestrian protection is

activated together with forward

collision alert.

The system uses the front camera in

the windscreen to detect a pedestrian

directly ahead in your path.

Front pedestrian protection can

detect and alert to pedestrians in a

forward gear at speeds between

3 mph and 37 mph.

Forward collision alert 3 145.

Detecting front pedestrian ahead

A pedestrian ahead up to a distance

of approx. 40 m is indicated by a

symbol in the instrument cluster.

if the brake lights are not working

Active emergency braking can be

deactivated in the personalisation

menu 3 96. If deactivated, m

150

Driving and operating

●

the sensor in the windscreen is

blocked by snow, ice, slush, mud,

dirt etc.

the windscreen is damaged or

affected by foreign objects, e.g.

stickers

Acoustic signals are given on the side

on which the vehicle is closer to an

obstacle. The interval between the

sounds becomes shorter as the

vehicle gets closer to that obstacle.

When the distance is less than

approx. 30 cm, the sound is

continuous.

Front pedestrian alert

When approaching a detected

pedestrian too quickly, a warning

message is displayed in the Driver

Information Centre. A warning chime

is provided.

Cruise control or Adaptive cruise

control may be disengaged when the

front pedestrian alert occurs.

Parking assist

General information

The system is switched off

automatically when attaching a trailer

or bike carrier to the trailer hitch.

Rear parking assist

System limitations

In the following cases, front

pedestrian protection may not detect

a pedestrian ahead or sensor

performance is limited:

9 Warning

●

vehicle speed is out of range from

The driver bears full responsibility

for the parking manoeuvre.

Always check the surrounding

area when driving backwards or

forwards while using parking

assist system.

3 mph to 37 mph in forward gear

●

the distance to an pedestrian

ahead is more than 40 m

driving on winding or hilly roads

driving in the dark

weather limits visibility, such as

fog, rain, or snow

●

The system operates with ultrasonic

parking sensors in the rear bumper.

The parking assist makes parking

easier by measuring the distance

between the vehicle and obstacles. It

informs and warns the driver by giving

acoustic signals and display

indication.

Activation

Rear parking assist is activated when

reverse gear is engaged.

Driving and operating

151

The system is ready to operate when

the LED in the parking assist button

¼ is not illuminated.

Deactivation

Indication

The system warns the driver with

acoustic signals against potentially

hazardous obstacles behind the

vehicle in a distance range up to

50 cm.

The system operates with ultrasonic

parking sensors in the rear and front

bumper.

The system is switched off when

reverse gear is disengaged. Press ¼

to deactivate the system manually.

The LED in the button illuminates

when the system is deactivated. If the

system has been deactivated

manually, it is not reactivated

automatically the next time the

ignition is switched on.

Activation

Rear parking assist is activated when

reverse gear is engaged.

In addition to the rear parking assist,

the front parking assist is triggered

when an obstacle is detected in front

and the speed of the vehicle is still

below 6 mph.

The system is ready to operate when

the LED in the parking assist button

¼ is not illuminated.

Additionally, the distance to rear

obstacles is displayed by changing

distance lines in the Info Display

3 91. When the obstacle is very close,

9 for danger is displayed in the

screen.

Front-rear parking assist

It uses two different acoustic warning

signals for the front and rear

monitoring areas, each with a

different tone frequency.

152

Driving and operating

Indication

Deactivation

System limitations

The system warns the driver with

acoustic signals against potentially

hazardous obstacles in front of the

vehicle and behind the vehicle by

using the respective loudspeakers.

In the event of a fault or if the system

does not work temporarily, e.g.

because of high external noise level

or other interference factors, Service

in the cluster instrument illuminates.

A message is indicated in the Driver

Information Centre.

9 Warning

Under certain circumstances,

various reflective surfaces on

objects or clothing as well as

external noise sources may cause

the system to fail to detect

obstacles.

Special attention must be paid to

low obstacles which can damage

the lower part of the bumper.

The system is deactivated

automatically when vehicle speed

exceeds 6 mph or if the vehicle stops

for more than 3 seconds in a forward

gear or if no further obstacles are

detected.

Additionally, the distance to rear and

front obstacles is displayed by

changing distance lines in the Info

Display 3 91.

When the system is deactivated

manually, the LED in the button

illuminates.

If the system has been deactivated

manually, it is not reactivated

automatically the next time the

ignition is switched on.

Driving and operating

153

Notice

Advanced parking assist provides

assistance for the following

manoeuvres:

Caution

Make sure that the front number

plate is properly mounted (not bent

and no gaps to the bumper on the left

or right side) and the sensors are

firmly in place.

Performance of the system can be

reduced when sensors are

covered, e.g. by ice or snow.

●

entry into a parallel parking slot

entry into a perpendicular parking

slot

Performance of the parking assist

system can be reduced due to

heavy loading.

Special conditions apply if there

are taller vehicles in the vicinity

(e.g. off-road vehicles, mini vans,

vans). Object identification and

correct distance indication in the

upper part of these vehicles

cannot be guaranteed.

Advanced parking assist

●

exit from a parallel parking slot

The driver must control acceleration,

braking and gear shifting, while

steering is done automatically. The

driver can take control at any time by

gripping the steering wheel.

It may be necessary to move forwards

and backwards more than once.

Instructions are given in the Info

Display 3 91.

Advanced parking assist can only be

activated when driving forwards.

9 Warning

The driver bears full responsibility

for accepting the parking slot

suggested by the system and the

parking manoeuvre.

Always check the surrounding

area in all directions when using

the advanced parking assist.

Objects with a very small reflection

cross-section, e.g. objects of

narrow size or soft materials, may

not be detected by the system.

The advanced parking assist

measures a suitable parking slot

while passing, calculates the

trajectory and automatically steers

the vehicle while parking.

Parking assist systems do not

detect objects outside the

detection range.

154

Driving and operating

8'' Colour Info Display: to search for a

parking slot, activate the system by

pressing Í. Select Driving functions

on the touch screen and then Park

Assist. Select Enter parallel parking

space.

$ illuminates in the instrument cluster

to confirm the function.

Slow down the vehicle speed below

12 mph.

Select parking side by switching on

turn light indicator on the respective

side.

The allowed parallel distance

between the vehicle and a row of

parked cars is between 0.5 m and

1.5 m.

The system will not identify slots that

are clearly smaller or larger than the

vehicle.

Advanced parking assist is always

combined with front-rear parking

assist.

The system has six ultrasonic parking

sensors each in both the rear and

front bumper.

When a free slot is detected, a visual

feedback on the Colour Info Display

and a first acoustic signal is given.

Drive slowly forwards. When the

second acoustic signal is given, stop

the vehicle, select reverse gear,

release the steering wheel and start

moving without exceeding 4 mph.

Entry into a parallel parking slot

Activation

7'' Colour Info Display: to search for a

parking slot, activate the system by

selecting Park Assist on the

homepage of the touch screen. Then

select Enter parallel parking space.

Driving and operating

155

8'' Colour Info Display: when search

for a parking slot, activate the system

by pressing Í. Select Driving

functions on the touch screen and

then Park Assist. Select Enter bay

parking space.

$ illuminates in the instrument cluster

to confirm the function.

Slow down the vehicle speed below

12 mph.

Select parking side by switching on

turn light indicator on the respective

side.

The allowed parallel distance

between the vehicle and a row of

parked cars is between 0.5 m and

1.5 m.

When several successive slots are

found, the vehicle will be directed

towards the last one.

Move forwards and backwards while

observing the warnings of the parking

assist until the end of manoeuvre is

indicated. When finished, $

When a free slot is detected, a visual

feedback on the Colour Info Display

and an acoustic signal is given. Stop

the vehicle, select reverse gear,

release the steering wheel and start

moving without exceeding 4 mph.

extinguishes in the instrument cluster.

Entry into a perpendicular parking

slot

Activation

7'' Colour Info Display: to search for a

parking slot, activate the system by

selecting Park Assist on the

homepage of the touch screen. Then

select Enter perpendicular parking

space.

156

Driving and operating

Exiting a parallel parking slot

Activation

7'' Colour Info Display: when exiting a

parallel parking slot, activate the

system by selecting Park Assist on

the homepage of the touch screen.

Then select Exit parallel parking

space.

8'' Colour Info Display: when exiting a

parallel parking slot, activate the

system by pressing Í. Select Driving

functions on the touch screen and

then Park Assist. Select Exit parallel

parking space.

Select exit side by switching on the

respective turn light indicator.

Engage reverse or forward gear,

release the steering wheel and start

moving without exceeding 3 mph.

Move forwards and backwards as

instructed by observing the warnings

of the parking assist and paying

attention to the acoustic signals until

the end of manoeuvre is indicated.

When finished, $ extinguishes in the

instrument cluster.

During the parking manoeuvre, the

system is automatically deactivated

once the rear of the vehicle is within

50 cm of an obstacle.

Move forwards and backwards while

observing the warnings of the parking

assist until the end of manoeuvre is

indicated. The manoeuvre is

complete when the vehicle's front

wheels are out of the parking slot and

$ extinguishes in the instrument

cluster.

After deactivation check control over

the vehicle.

Driving and operating

157

The system is deactivated

automatically:

The system is switched off

Display indication

The instructions on the display show:

automatically when attaching a trailer

or bike carrier to the trailer hitch.

Contact your dealer to switch off the

system for a prolonged period.

●

if the ignition is switched off

if stalling the engine

if no manoeuvre is started within

5 minutes of selection of the type

of manoeuvre

●

general hints and warning

messages

the demand to stop the vehicle,

when a parking slot is detected

the direction of driving during the

parking manoeuvre

the demand to shift into reverse

or first gear

the demand to stop or to drive

slowly

Fault

In the event of a fault, $ flashes for a

few seconds, accompanied by an

acoustic signal. If the fault occurs

during the use of the system, $

extinguishes.

In the event of a fault in the power

steering, c flashes in the instrument

panel, accompanied by a message.

●

after a prolonged stop of the

vehicle during a manoeuvre

if the electronic stability control is

triggered

if the speed of the vehicle

exceeds the stated limit

when the driver interrupts

movement of the steering wheel

the successful completion of the

parking manoeuvre indicated by

a pop-up symbol and a chime

Notice

●

after four manoeuvre cycles

on opening the driver's door

if one of the front wheels

encounters an obstacle

It is possible that the sensor detects

a non-existing object caused by

echo disturbance from external

acoustic noise or mechanical

misalignments (sporadic false

warnings may occur).

●

the cancelling of a parking

manoeuvre

Deactivation

The current park assist manoeuvre is

cancelled via the button to return to

the previous screen in the Colour Info

Display. To deactivate the system

completely, press r Off in the

centre console.

●

parking manoeuvre successfully

ended

Advanced parking assist system

may not respond to changes in the

available parking space after

initiating a parking manoeuvre. The

system may recognise an entry, a

gateway, a courtyard or even a

Deactivation by the driver or by the

system during manoeuvring will be

indicated on the display. Additionally,

an acoustic signal sounds.

158

Driving and operating

crossing as a parking slot. After

selecting reverse gear the system

will start a parking manoeuvre. Take

care regarding the availability of the

suggested parking slot.

Low curbs and surface irregularities,

e.g. on construction zones, are not

detected by the system. The driver

accepts responsibility.

Functionality

●

vehicles outside the side blind

zones which may be rapidly

approaching

pedestrians, cyclists or animals

Before changing a lane, always

check all mirrors, look over the

shoulder and use the turn light.

Activation

7'' Colour Info Display: select Blind

spot monitoring on the Info Display

and activate the function.

Side blind spot alert

The side blind spot alert system

detects and reports objects on either

side of the vehicle, within a specified

blind spot zone. The system displays

a visual alert in each exterior mirror,

when detecting objects that may not

be visible in the interior and exterior

mirrors.

8'' Colour Info Display: press Í.

Select Driving functions on the Info

Display and then Blind spot

When the system detects a vehicle in

the side blind zone while driving

forwards, an LED will illuminate in the

relevant exterior mirror.

The LED comes on immediately when

being passed.

monitoring. Activate the function.

B illuminates continously green in the

instrument cluster to confirm the

function.

Side blind spot alert uses some of the

parking assist sensors.

The LED comes on after a delay when

passing another vehicle slowly.

9 Warning

Side blind spot alert does not

replace driver vision.

The system does not detect:

Driving and operating

Fault

159

●

when passing or being passed by

a very long vehicle, e.g. lorry,

coach, which is at the same time

detected at the rear in the blind

spot angle and present in the

driver's forward field of vision

in very heavy traffic: vehicles

detected in front and behind are

confused with a lorry or a

stationary object

Operation conditions

The following conditions must be

fulfilled for proper operation:

In the event of a fault, B flashes for a

few moments in the instrument

cluster, accompanied by C and a

display message. Seek the

●

all vehicles are moving in the

same direction and in adjacent

lanes

assistance of a workshop.

●

the vehicle speed is between 7

Panoramic view system

and 87 mph

passing a vehicle with a speed

difference of less than 6 mph

another vehicle is passing with a

speed difference of less than

15 mph

This system allows views of the

vehicle's surroundings to be

when passing too quickly

displayed as a nearly 180° picture in

Deactivation

the Info Display, like a bird's eye view.

The system uses:

The system is deactivated in the

vehicle personalisation 3 96. B

extinguishes in the instrument cluster.

Additionally, an acoustic signal

sounds.

The state of the system is stored

when switching off the ignition.

●

the traffic flow is normal

driving on a straight or slightly

curved road

●

rear camera, installed in the

tailgate

●

ultrasonic parking sensors in the

rear bumper

No alert will be given in the following

situations:

The screen is divided into two parts:

on the right there is a view from above

the vehicle, and on the left there are

different views displayed.

●

in the presence of non-moving

objects, e.g. parked vehicles,

barriers, street lamps, road signs

The system is switched off

automatically when attaching a trailer

or bike carrier to the trailer hitch.

●

with vehicles moving in the

Due to adverse weather conditions

such as heavy rain, false detections

may occur.

opposite direction

driving on a winding road or a

sharp corner

160

Driving and operating

●

zoom view

180° view

vehicle with mirrors unfolded. The

direction of the lines changes with the

steering angle.

The horizontal lines represent a

distance of about 30 cm, 1m and 2 m

beyond the rear bumper.

Activation

Panoramic view system is activated

by:

Auto mode is activated by default. In

this mode, the system selects the

best view, standard or zoom, to

display according to the information

from the parking sensors.

The state of the system is not kept in

memory when the ignition is switched

off.

●

engaging reverse gear

driving up to 6 mph

This view is available in auto mode or

in the view selection menu.

Functionality

Auto mode

This mode is activated by default.

Using sensors in the rear bumper, the

automatic view changes from a rear

view to a view from above, as an

obstacle is approached during a

manoeuvre.

Rear view

Different views can be selected in the

left part of the display. Change the

type of view by pressing the touch

field in the left lower zone of the

display:

The area behind the vehicle is

displayed in the screen. The vertical

lines represent the width of the

●

rear view

auto mode

Driving and operating

Deactivation

161

Zoom view

180° view

Panoramic view system is

deactivated when:

●

driving faster than 6 mph

7 seconds after disengaging

reverse gear

●

by pressing the icon q in the left

upper corner of the touch screen

●

opening the tailgate

General information

9 Warning

The camera records the vehicle's

surroundings during the manoeuvre

in order to reconstruct a view from

above the rear of the vehicle in its

near surroundings, allowing the

vehicle to be manoeuvred around

obstacles nearby. This view is

available with auto mode or in the

view selection menu.

The 180° view facilitates reversing

out of a parking bay, making it

possible to see the approach of

vehicles, pedestrians and cyclists.

This view is not recommended for

carrying out a complete manoeuvre.

It is made up of three areas: left 1,

centre 2 and right 3. This view is

available from the view selection

menu only.

The panoramic view system does

not replace driver vision. It will not

display children, pedestrians,

cyclists, crossing traffic, animals,

or any other objects outside of the

camera view area, e. g. below the

bumper, or underneath the

vehicle.

Do not drive or park the vehicle

using only the panoramic view

system.

Always check the surrounding of

the vehicle before driving.

162

Driving and operating

●

During nighttime driving.

Weather limits visibility, such as

fog, rain, or snow.

The camera lenses are blocked

by snow, ice, slush, mud, dirt.

A trailer or bike carrier is attached

to the trailer hitch.

The vehicle had an accident.

There are extreme temperature

changes.

Displayed images may be further

or closer than they appear. The

area displayed is limited and

objects that are close to either

edge of the bumper or under the

bumper are not displayed on the

screen.

Do not reverse or park the vehicle

using only the rear view camera.

Always check the surrounding of

the vehicle before driving.

●

Switching on

Rear view camera is automatically

activated when reverse gear is

engaged.

●

System limitations

Caution

Functionality

For optimal operation of the

Rear view camera

system, it is important to keep the

lense of the camera in the tailgate

between the number plate lights

always clean. Rinse the lense with

water and wipe with a soft cloth.

The rear view camera assists the

driver when reversing by displaying a

view of the area behind the vehicle.

The view of the camera is displayed

in the Info Display.

Do not clean the lense with a

steam-jet or high-pressure jet

cleaner.

9 Warning

The rear view camera does not

replace driver vision. Note that

objects that are outside the

camera's field of view and the

parking assist sensors, e.g. below

the bumper or underneath the

vehicle, are not displayed.

The panoramic view system may not

operate properly when:

●

The surrounding is dark.

The area displayed by the camera is

limited. The distance of the image that

appears on the display differs from

the actual distance.

The sun or the beam of

headlights is shining directly into

the camera lenses.

Driving and operating

163

Guidelines

Switching off

Lane departure warning

The lane departure warning system

observes the lane markings between

which the vehicle is driving via a front

camera. The system detects lane

changes and warns the driver in the

event of an unintended lane change

via visual and acoustic signals.

The camera is switched off when a

certain forward speed is exceeded or

if reverse gear is disengaged for

approx. 10 seconds.

System limitations

The rear view camera may not

operate properly when:

Criteria for the detection of an

unintended lane change are:

●

The surrounding is dark.

The beam of headlights is shining

directly into the camera lenses.

●

no operation of turn lights

no brake pedal operation

no active acceleration

●

During nighttime driving.

Weather limits visibility, such as

fog, rain, or snow.

The vertical lines represent the width

of the vehicle without mirrors and the

general direction of the vehicle. The

horizontal lines represent a distance

of about 30 cm, 1m and 2 m beyond

the rear bumper. The crossing curves

represent the maximum turning circle.

If the driver is active, no warning will

be issued.

●

The camera lenses are blocked

by snow, ice, slush, mud, dirt.

Clean the lense, rinse with water,

and wipe with a soft cloth.

●

The tailgate will be opened.

A trailer or bike carrier is attached

to the trailer hitch.

The vehicle had a rear end

accident.

There are extreme temperature

changes.

Deactivation of guidelines

Guidelines can be deactivated in the

Info Display. Select Settings I Vehicle

I Collision detection I Rear view

camera guide lines I §.

●

Info Display 3 91.

Vehicle personalisation 3 96.

164

Driving and operating

●

driving in the dark

weather limits visibility, such as

fog, rain, or snow

Activation

●

the camera is blocked by snow,

ice, slush, mud, dirt, windscreen

damage or affected by foreign

items, e.g. stickers

Deactivation

The system is deactivated by

pressing ½, the LED in the button

illuminates.

At speeds below 37 mph the system

is inoperable.

●

the sun is shining directly into the

camera lens

●

close vehicles ahead

banked roads

road edges

roads with poor lane markings

sudden lighting changes

The lane departure warning system is

activated by pressing ½. The system

is switched on when the LED in the

button is not illuminated.

The system is only operable at

vehicle speeds above 37 mph and if

lane markings are available.

When the system recognises an

unintended lane change, the control

indicator ) flashes yellow.

Simultaneously a chime sound is

activated.

Fault

In the event of a fault, C appears in

the instrument cluster, accompanied

by a display message. Seek the

assistance of a workshop.

The system cannot operate when no

lane marking is detected.

Driver alert

9 Warning

The system cannot replace the

need for vigilance on the part of

the driver. Taking a break is

recommended as soon as feeling

tired or at least every two hours.

Do not take the steering wheel

when feeling tired.

System limitations

The system may not operate properly

when:

●

vehicle speed is below 37 mph

driving on winding or hilly roads

Driving and operating -> Driver assistance systems for Your Vauxhall Crossland SUV First Generation (2020-2024)

Related Topics

Driving and operating

Popular Owner Manuals

Latest Owner Manuals