Driving and operating -> Starting and operating for Your Vauxhall Crossland SUV First Generation (2020-2024)

122  
Driving and operating  
Steering  
Driving hints  
Control of the vehicle  
Never coast with engine not  
running  
Many systems will not function in this  
situation (e.g. brake servo unit, power  
steering). Driving in this manner is a  
danger to yourself and others.  
Starting and operating  
If power steering assist is lost  
because the engine stops or due to a  
system malfunction, the vehicle can  
be steered but may require increased  
effort.  
New vehicle running-in  
Do not brake unnecessarily hard for  
the first few journeys.  
During the first drive, smoke may  
occur because of wax and engine oil  
evaporating off the exhaust system.  
Park the vehicle in the open for a  
while after the first drive and avoid  
inhaling the fumes.  
During the running-in period, fuel and  
engine oil consumption may be  
higher.  
All systems function during an  
Autostop.  
Stop-start system 3 126.  
Pedals  
Additionally, the cleaning process of  
the exhaust filter may take place more  
often.  
To ensure the pedal travel is  
uninhibited, there must be no mats in  
the area of the pedals.  
Exhaust filter 3 129.  
Use only floor mats, which fit properly  
and are fixed by the retainers on the  
driver side.  
Driving and operating  
123  
Engine start  
Ignition switch positions  
9 Danger  
Operate the clutch pedal, the brake  
pedal and press Start/Stop. Release  
the button after starting procedure  
begins.  
Never remove the key from  
ignition switch during driving as  
this will cause steering wheel lock.  
Engine and ignition off  
Press Start/Stop briefly in each mode  
or when engine is running and vehicle  
is stationary. Some functions remain  
active until driver's door is opened,  
provided the ignition was on  
previously.  
Power button  
Emergency shut off during driving  
If the engine needs to be switched off  
during driving in case of emergency,  
press Start/Stop for 5 seconds.  
0 : ignition off: some functions  
remain active until key is  
removed or driver's door is  
opened, provided the ignition was  
on previously  
1 : ignition on power mode: ignition  
is on, control indicators illuminate  
and most electrical functions are  
operable  
2 : engine start: release key after  
engine has been started  
9 Danger  
Switching off the engine during  
driving may cause loss of power  
support for brake and steering  
systems. Assistance systems and  
airbag systems are disabled.  
Lighting and brake lights will  
The electronic key must be inside the  
vehicle.  
Ignition on power mode without  
starting the engine  
Press Start/Stop without operating a  
pedal. Control indicators illuminate  
and most electrical functions are  
operable.  
Steering wheel lock  
Remove key from ignition switch and  
turn steering wheel until it engages.  
extinguish. Therefore power down  
124  
Driving and operating  
display No Remote Detected or  
Replace Battery in Remote Key when  
you try to start the vehicle.  
For unlocking or locking the doors,  
see fault in radio remote control unit  
or electronic key system 3 23.  
the engine and ignition while  
driving only when required in case  
of emergency.  
Steering wheel lock  
The steering wheel lock activates  
automatically when:  
Starting the engine  
Vehicles with ignition switch  
The vehicle is stationary.  
The ignition has been switched  
off.  
To release steering wheel lock, open  
and close driver's door and switch the  
ignition on power mode or start the  
engine directly.  
Hold the electronic key with buttons  
outside at the marking on the steering  
column cover as shown in the  
illustration.  
Operate the clutch pedal, the brake  
pedal and press Start/Stop. Release  
the button after starting procedure  
begins.  
9 Warning  
If the vehicle battery is discharged,  
the vehicle must not be towed,  
tow-started or jump-started as the  
steering wheel lock cannot be  
disengaged.  
Turn key to position 1.  
Move the steering wheel slightly  
to release the steering wheel  
lock.  
This option is intended for  
emergencies only. Replace the  
electronic key battery as soon as  
possible 3 22.  
Manual transmission: operate  
Operation in case of failure  
If either the electronic key fails or the  
battery of the electronic key is weak,  
the Driver Information Centre may  
clutch and brake pedal.  
Automatic transmission: operate  
brake pedal and move selector  
lever to P or N.  
Driving and operating  
125  
Do not operate accelerator pedal.  
Diesel engines: wait until control  
indicator ! extinguishes.  
Turn key to position 2 and  
release after the engine has been  
started.  
Manual transmission: operate  
clutch and brake pedal.  
Automatic transmission: operate  
brake pedal and move selector  
lever to P or N.  
Starting the vehicle at low  
temperatures  
Starting the engine without additional  
heaters is possible down to -25 °С for  
diesel engines and -30 °C for petrol  
engines.  
Required is an engine oil with the  
correct viscosity, the correct fuel,  
performed services and a sufficiently  
charged vehicle battery.  
With temperatures below -30 °C the  
automatic transmission requires a  
warming phase of approx. 5 minutes.  
The selector lever must be in position  
P.  
Do not operate accelerator pedal.  
Manual transmission: during an  
Autostop, the engine can be started  
by depressing the clutch pedal  
3 126.  
Automatic transmission: during an  
Autostop, the engine can be started  
by releasing the brake pedal 3 126.  
Press Start/Stop button. Release  
button after starting procedure  
begins.  
Diesel engine starts after control  
indicator ! for preheating  
extinguishes.  
Before restarting or to switch off  
the engine when vehicle is  
stationary, press Start/Stop once  
more briefly.  
Vehicles with power button  
Turbo engine warm-up  
To start the engine during an  
Autostop:  
Upon start-up, engine available  
torque may be limited for a short time,  
especially when the engine  
temperature is cold. The limitation is  
to allow the lubrication system to fully  
protect the engine.  
Manual transmission: during an  
Autostop, the engine can be  
started by depressing the clutch  
pedal 3 126.  
Automatic transmission: during  
an Autostop, the engine can be  
started by releasing the brake  
pedal 3 126.  
126  
Driving and operating  
If the stop-start system is temporarily  
not available and the button Ò is  
pressed, the LED in the button  
flashes.  
Activate an Autostop as follows:  
Overrun cut-off  
Depress the clutch pedal.  
Set the lever to neutral.  
Release the clutch pedal.  
The fuel supply is automatically cut off  
during overrun, i.e. when the vehicle  
is driven with a gear engaged but  
accelerator pedal is released.  
Deactivation  
The engine will be switched off while  
the ignition stays on.  
Depending on driving conditions, the  
overrun cut-off may be deactivated.  
Vehicles with automatic transmission  
If the vehicle is at a standstill with  
depressed brake pedal, Autostop is  
activated automatically.  
The engine will be switched off while  
the ignition stays on.  
Stop-start system  
The stop-start system helps to save  
fuel and to reduce the exhaust  
emissions. When conditions allow, it  
switches off the engine as soon as the  
vehicle is at a low speed or at a  
standstill, e.g. at a traffic light or in a  
traffic jam.  
The stop-start system will be disabled  
on inclines of 12% or more.  
Indication  
Activation  
Deactivate the stop-start system  
manually by pressing Ò. The  
deactivation is indicated when the  
LED in the button illuminates.  
The stop-start system is available as  
soon as the engine is started, the  
vehicle starts-off and the conditions  
as stated below in this section are  
fulfilled.  
Autostop  
The system is ready to operate when  
the LED in the button Ò is not  
illuminated. To activate the system  
when the system is deactivated,  
press Ó.  
Vehicles with manual transmission  
An Autostop can be activated at a  
standstill.  
An Autostop is indicated by control  
indicator D.