Get Transport -> Towing a trailer Guide for Volkswagen ID.5 SUV First Generation (2021-2025)

Closing the load-through hatch

1. Fold back the flap of the load-through hatch until it engages in position.

There may be a red marking on the luggage compartment side. This must not be visible →

2. Close the boot lid.

.

3. If necessary, fold back the centre armrest.

WARNING

Objects in the deployment zone of the centre airbag can prevent it from functioning properly and cause serious or fatal injuries.

● Never push objects forward into the deployment zones of the centre airbag (→ Airbag system).

WARNING

Serious or fatal injuries could be caused if the load-through hatch is folded forwards or backwards carelessly or in an uncontrolled

way.

● Never fold the load-through hatch forwards or backwards while the vehicle is in motion.

● Ensure that the seat belt is not trapped or damaged when folding back the load-through hatch.

● Always keep hands, fingers, feet or other body parts away from the swivel area when folding the load-through hatch forwards and

backwards.

● Always make sure that the red mark on the locking indicator is never visible when the load-through hatch is in the upright position.

The load-through hatch is not engaged properly if you can see a red marking.

● Never transport a person, particularly a child, on this seat if the load-through hatch is folded forward or not securely engaged.

The vehicle can be used to tow a trailer if it has the required technical equipment for this.

Driving with a trailer not only places an extra load on the vehicle, but also requires increased concentration on the part of the driver.

The additional trailer load will affect the amount of wear, consumption and performance of the vehicle and, in certain circumstances,

could shorten the service intervals.

If the vehicle is driven under high loads, certain functions, e.g. the output of the air conditioning system, may be reduced or switched

off to stop the vehicle from breaking down.

The load that a vehicle can actually pull decreases under the following conditions:

—Driving on uphill gradients.

—Driving at high altitudes.

—Driving at high outside temperatures.

—Driving with a fully loaded vehicle, e.g. with passengers and luggage.

—With increasing speed.

Trailer with function check for lighting

No trailer with tail lights and brake lights must be operated with this vehicle that requires a function check of the tail and brake lights

in its approval. Ask the trailer manufacturer about the approval that is valid for your trailer.

Unused ball coupling

Swivel in the ball coupling or remove it if there is no trailer, bicycle carrier or similar attached to the ball coupling. This applies in

particular if the unused ball coupling covers the number plate or the lighting at the rear of the vehicle. Observe the country-specific

regulations on use of a towing bracket →

.

Points to note

Before driving with a trailer, pay attention to possible functional restrictions of the assist and parking systems.

DANGER

It is dangerous to transport people in a trailer and it may also be illegal.

● Never transport people in a trailer.

WARNING

Improper use of the towing bracket can lead to a loss of vehicle control, accidents and serious or fatal injuries.

● Attach and use the trailer in accordance with the instructions supplied by the respective manufacturer.

● Use the towing bracket only if it is undamaged and fitted correctly.

● Do not carry out any alterations or repairs to the towing bracket. If required by the trailer manufacturer’s installation instructions,

removal of the coating on the ball head is permitted.

WARNING

When the ball coupling is swivelled out, there is an increased risk of accidents and serious injuries for pedestrians and cyclists when

vehicles are parked and also in the event of rear-end collisions.

● Swivel in the ball coupling or remove it when it is not in use.

WARNING

The vehicle was not designed for “weight-distributing” or “load-compensating” towing brackets. The towing bracket can fail, causing

the trailer to tear loose from the vehicle. This can result in accidents and severe injuries.

● Never install a “weight-distributing” or “load-balancing” towing bracket on the vehicle.

WARNING

Towing a trailer and transporting heavy or bulky items can change the vehicle handling, increase the braking distance and cause

accidents and serious or fatal injuries.

● Always secure loads properly using suitable and undamaged lashing, retaining or securing straps.

● Please note that a trailer with a high centre of gravity can tip over more easily than a trailer with a low centre of gravity.

● Always adapt your speed and driving style to the current visibility, weather and road or traffic conditions.

● Always pay attention to the road ahead and drive carefully.

● Accelerate particularly carefully and gently.

● Avoid abrupt and sudden driving and braking manoeuvres.

● Do not drive faster than 80 km/h (50 mph) when towing a trailer, or also 100 km/h (60 mph) in exceptional cases. This also applies

to countries where higher speeds are permitted.

● Reduce speed, particularly on uphill gradients and when driving downhill.

● Always observe the country-specific maximum permitted speed for vehicles with trailer.

● Take particular care when overtaking and reduce your speed immediately if the trailer shows even the slightest sign of snaking.

● Never try to stop a vehicle and trailer from snaking by increasing your speed.

● Due to the higher load for the towing vehicle, pay attention to possible messages and to any warning and indicator lamps that light

up in the instrument cluster.

Please observe the notes and information for vehicles with N1 approval (→ N1 approval).

If the connection to a trailer connected to the anti-theft alarm system is interrupted, the anti-theft alarm system may be

triggered (→ Anti-theft alarm).

Some retrofitted towing brackets may cover the opening for fitting the towing eye. If so, the towing eye cannot be used for

towing or tow-starting other vehicles. For this reason, the removed ball coupling of a retrofitted towing bracket should be

stored in the vehicle at all times.

Trailer socket

The electrical connection between the towing vehicle and the trailer requires a 13-pin trailer socket. The pin assignment is in

accordance with DIN ISO 11446.

If the trailer has a 7-pin plug you will need to use a suitable adapter.

1. Lift up the closure cap of the socket and insert the plug.

2. Turn the plug by quarter of a turn in clockwise direction until it completely engages in the socket.

3. Release the cap to lock the plug in position.

4. Check that the entire lighting system is working before starting your journey.

If you are uncertain whether the electrical connection of the trailer with the vehicle is correct, please contact a suitably qualified

workshop. Volkswagen recommends using an authorised Volkswagen repairer.

Connection to the anti-theft alarm

The trailer is integrated in the anti-theft system if the following conditions are fulfilled:

When the vehicle has a factory-fitted anti-theft alarm and a factory-fitted towing bracket.

When the trailer is electrically connected to the towing vehicle via the trailer socket.

When the vehicle and trailer electric systems are functional, fault-free and undamaged.

When the vehicle is locked with the vehicle key and the anti-theft alarm is active.

When the vehicle is locked, the alarm will be triggered as soon as the electrical connection to the trailer is interrupted.

For technical reasons, trailers with LED tail light clusters cannot be integrated into the anti-theft alarm system.

When the vehicle is locked, the alarm is not triggered as soon as the electrical connection to the trailer with LED tail light clusters is

interrupted.

Safety cable

In some countries, unbraked and braked trailers must be secured by means of a safety or breakaway cable.

On the towing bracket: eye for securing the safety or

breakaway cable (illustration).

Depending on model, the eye for securing the safety or breakaway cable may be located on the neck of the ball head or next to the ball

head directly on the ball coupling carrier → Fig. 1 (arrows).

Observe the country-specific regulations on using a safety cable.

Secure the safety or breakaway cable at the eye provided for this purpose on the ball coupling → Fig. 1:

1. Guide the cable through the eye and hook into the snap hook →

.

WARNING

Any electrical cables that are not connected properly or are connected incorrectly could cause a power surge to the trailer. This could

lead to faults in the entire vehicle electronics system and could also cause accidents and serious or fatal injuries.

● Have all work on the electrical system carried out only by a suitably qualified workshop. Volkswagen recommends using an

authorised Volkswagen repairer.

● Never connect the trailer’s electrical system directly to the electrical connections of the towing vehicle’s tail light clusters or to

other power sources.

WARNING

Contact between the pins in the trailer socket can lead to short circuits, overloading of the electrical system and failure of the lighting

system, thereby causing accidents and serious or fatal injuries.

● Never connect the pins in the trailer socket to one another.

● Have bent pins repaired by a suitably qualified workshop. Volkswagen recommends using an authorised Volkswagen repairer.

WARNING

If the trailer is not properly secured, this could cause accidents and serious or fatal injuries.

● Never place the trailer’s safety or breakaway cable loosely over the ball coupling.

NOTICE

If a trailer hitched to the vehicle is parked using the support wheel or on the trailer supports, the vehicle height may be lowered or

raised due to any changes in the load or tyre damage. Powerful forces then act on the towing bracket and the trailer. This can cause

damage to the vehicle and trailer.

● Please note that a trailer that is parked using the support wheel or the trailer supports must not remain hitched to the vehicle.

If the engine is not running and electrical equipment is switched on in the trailer via the trailer socket, the 12-volt vehicle

battery will discharge.

If the 12-volt vehicle battery charge level is low, the electrical connection to the trailer will be interrupted automatically.

Basic information

If the vehicle is approved for towing a trailer, observe any local regulations for driving with a trailer and using a towing bracket.

Always make sure that the vehicle and trailer are well-balanced. Do not load the trailer with more weight either at the front or rear.

Always stow heavy items as close as possible to or over the axle. Always secure the load on the trailer properly →

.

Things to note for vehicles with N1 approval

If the vehicle exceeds the permitted gross weight or axle load for the rear axle, a speed of around 80 km/h (around 50 mph) must not

be exceeded when towing a trailer. This also applies to countries where higher speeds are permitted. Observe local speed limits. These

may be lower for vehicles with trailers than for vehicles without trailers.

Any permitted excess loads for the vehicle are entered in the vehicle documents. If no permitted excess load is entered, the permitted

driving speed limit is around 100 km/h (around 62 mph) taking into account country-specific legislation.

Maximum trailer weight and drawbar load

The maximum trailer weight is the weight that the vehicle can pull.

The drawbar load is the weight that is exerted vertically from above on the ball coupling of the towing bracket.

Volkswagen recommends always making full use of the maximum permitted drawbar load . The response of the trailer on the road will

be poor if the drawbar load is too small. However, the maximum permitted load exerted by the trailer drawbar on the ball coupling of

the towing bracket must not be exceeded →

.

The actually present drawbar load increases the weight on the rear axle and reduces the maximum load of the vehicle as a result.

A higher drawbar load can be used in some countries subject to certain conditions. Observe the country-specific information and

regulations.

Gross combination weight

The gross combination weight is made up of the actual weight of the loaded vehicle and loaded trailer.

In some countries, trailers are divided into different classes. Volkswagen recommends that you contact a suitably qualified workshop to

find out about suitable trailers. Volkswagen recommends using an authorised Volkswagen repairer.

Tyre pressure

Follow the trailer manufacturer’s recommendations concerning the tyre pressure for the trailer tyres.

When towing a trailer, inflate the tyres on the towing vehicle with the maximum permitted tyre pressure (→ Tyre pressure).

WARNING

Moving loads can severely impair the stability and driving safety of the vehicle and trailer, which can cause accidents and serious or

fatal injuries.

● Always load the trailer correctly.

● Always secure loads using suitable and undamaged lashing, retaining or securing straps.

WARNING

Accidents and serious or fatal injuries can occur if you exceed the vehicle’s maximum permitted gross axle weight rating, drawbar

load, gross vehicle weight rating or gross combination weight rating.

● Never exceed the specified values .

Headlight adjustment

Towing a trailer can raise the front end of the vehicle so that the dipped beam dazzles other road users. Use the headlight range control

to lower the light cone as required. Vehicles with dynamic headlight range control are adjusted automatically.

Things to note when driving with a trailer

—If the trailer has an overrun brake, apply the brakes gently at first and then firmly. This will prevent the jerking that can be caused by

the trailer wheels locking.

—The combination weight causes the braking distance to increase.

—Select a higher brake energy recuperation level on downhill gradients. This will make use of the electric drive braking effect and

relieve the load on the brakes. The brake system could otherwise overheat and fail.

—The vehicle’s centre of gravity and in turn the vehicle handling will change because of the trailer load and the increased gross weight

of the vehicle and trailer.

—The weight distribution of a loaded trailer with an unladen towing vehicle is very unfavourable. When driving in this situation, drive

particularly carefully and slowly.

Pulling off on uphill gradients when towing a trailer

A vehicle towing a trailer is liable to roll back a short distance when moving off on an uphill slope depending on the gradient and the

gross weight of the trailer and vehicle.

When towing a trailer, pull off on uphill gradient as follows:

1. Depress and hold the brake pedal.

2. Select position

.

The electronic parking brake is switched off.

3. Press and hold the

4. Release the brake pedal.

5. Pull away slowly.

button to hold the vehicle and trailer with the electronic parking brake.

6. Release the

button only when the electric drive generates sufficient power to move off.

WARNING

Incorrect trailer towing can cause loss of vehicle control and serious or fatal injuries.

● Please note that the vehicle handling changes when towing a trailer and when transporting heavy or bulky objects.

● Always adapt your speed and driving style to the current visibility, weather and road or traffic conditions.

● Always pay attention to the road ahead and drive carefully.

● Take particular care when overtaking.

● Reduce your speed if the trailer shows even the slightest sign of snaking.

● Accelerate particularly carefully and gently.

● Brake earlier than usual because the braking distance may be longer than normal.

● Avoid abrupt and sudden driving and braking manoeuvres.

● Reduce speed particularly when driving downhill.

● Never try to stop a vehicle and trailer from snaking by increasing your speed.

● Keep to speed limits, which may be lower for vehicles with trailers than for vehicles without trailers.

WARNING

If there is insufficient visibility to the rear when towing a trailer, this can lead to accidents and serious or fatal injuries.

● Make sure that you have an adequate view to the rear.

● Fit suitable additional rear view mirrors so that there is sufficient visibility to the rear.

The trailer stabilisation function can detect if an attached trailer is starting to snake from side to side and can provide countersteer.

Trailer stabilisation is an extension of the Electronic Stability Control (ESC).

If trailer snaking is detected, the trailer stabilisation function automatically helps to reduce the trailer’s motion by means of counter

steering assistance.

Prerequisites for trailer stabilisation

—The vehicle has a factory-fitted towing bracket or a compatible towing bracket has been retrofitted.

—Electronic Stability Control (ESC) and the traction control system (TCS) are active. The indicator lamp or in the instrument cluster

is not lit up.

—The trailer is electrically connected to the towing vehicle via the trailer socket.

—The vehicle speed is higher than approximately 60 km/h (37 mph).

—The maximum drawbar load is being used.

—The trailer must have a rigid drawbar.

—Trailers with brakes must have a mechanical overrun system.

System limits

The trailer stabilisation system cannot react or will react in a restricted way in the following driving situations.

—Trailer stabilisation is switched off when ESC is deactivated.

—Light trailers that are snaking will not be recognised by the trailer stabilisation function and stabilised accordingly in all cases.

—A trailer can still jack-knife on slippery roads with little grip, even if the towing vehicle is equipped with the trailer stabilisation

system.

—Trailers with a high centre of gravity might tip over before snaking starts.

—Sudden braking procedures could occur automatically in extreme driving situations if the trailer socket is being used without a trailer

(e.g. for a bicycle carrier with lighting).

WARNING

The trailer stabilisation system is not a substitute for the full attention of the driver and operates only within the limits of the system.

The trailer stabilisation system therefore cannot recognise all driving situations and may not react or may react with a delay or in an

undesired way. If you do not pay due attention, there is a risk of accidents and serious or even fatal injuries.

● Always pay due attention and do not rely exclusively on the system. The driver is always responsible for all driving tasks.

● Observe the system limits → System limits.

● Accelerate carefully on slippery surfaces.

● Take your foot off the accelerator if a system is performing a control intervention.

Transport -> Towing a trailer for Your Volkswagen ID.5 SUV First Generation (2021-2025)

Related Topics

Transport

Popular Owner Manuals

Latest Owner Manuals