Advertisement

Advertisement

Wheels -> Changing the wheel and raising the vehicle for Your Volkswagen T Cross SUV First Generation (2018-2025)

Removing  
Do not start the engine of the lifted vehicle.  
·
NOTICE  
Danger of damage to vehicle!  
Make sure that the jack is attached correctly to  
the bridge of the sill.  
·
After having been changed  
— Check the tyre pressure on the mounted wheel  
and adjust if necessary.  
— In vehicles with a tyre indicator, save the tyre  
pressure values in the system.  
— Unscrew the lock nut.  
— Take out the wheel.  
— Have the tightening torque of the wheel bolts of  
the mounted tyres checked with a torque wrench  
as soon as possible.  
Inserting  
— Insert the wheel into the wheel well with the out-  
side facing downwards.  
The specified tightening torque is 140 Nm.  
Drive carefully until the tightening torque is  
checked.  
— Screw in the locknut until it stops.  
Replace the damaged tyre. It is not recommended to  
repair the tyre.  
Changing the wheel and rais-  
ing the vehicle  
WARNING  
Risk of an accident!  
Too low a tightening torque may cause the  
wheel to disengage while driving.  
·
What you should be mindful of  
Too high a tightening torque can damage the  
threads and cause the rim to deform.  
·
Before changing  
— Park the vehicle securely and secure it from roll-  
ing away.  
WARNING  
Block the wheel that is diagonally opposite the  
wheel to be changed at the front and rear with  
suitable means.  
Risk of an accident!  
Do not grease or lubricate screws.  
·
Do not use corroded or damaged screws.  
·
— Turn off the engine.  
— Let all of the occupants get out. During the wheel  
change they should not stand on the road, e.g.  
behind the crash barriers.  
Changing the wheel and raising the  
vehicle  
— Close all doors, the boot and bonnet.  
Raise vehicle  
Release screws  
WARNING  
— If the vehicle has covers over the wheel bolts or  
wheel trims, remove them.  
Always ensure the base plate of the lifting jack  
cannot slip!  
WARNING  
Provide a wide and firm base under the jack on  
loose surfaces.  
·
If you step on the key end when loosening the  
screw, hold on to the vehicle for better stability.  
·
Create a non-slip base (e.g. a rubber floor mat)  
under the jack on a smooth surface.  
·
Some vehicles may have anti-theft wheel bolts that  
protect the wheels from theft.  
Always raise the vehicle with the doors closed.  
·
·
Do not insert any body parts under the raised  
vehicle.  
114  
Wheels  
— Position the jack at the jacking point closest to  
the wheel to be replaced.  
— Insert the upper section on the anti-theft wheel  
bolt until it stops.  
— Support the base plate of the jack with its full  
area resting on level ground and ensure that the  
jack is located in a vertical position at the jacking  
point.  
— Use the crank to raise the jack until its claw enc-  
loses the bar.  
— Continue to lift the vehicle until the wheel is just  
off the floor.  
Changing a wheel  
— Unscrew the screws and place them on a clean  
surface.  
— Place the key on the wheel bolt or on the attach-  
ment piece.  
— Remove the original wheel carefully.  
— Attach the new wheel.  
— Turn the screw a maximum of half a turn so that  
the wheel does not come loose and fall off.  
— Slightly screw in the screws.  
— Lower the vehicle.  
Jacking points for the jack  
The mounting bars are located on the underside of  
the vehicle's undercarriage.  
NOTICE  
Applies to an anti-theft wheel bolt fitted at the fac-  
tory or supplied from Volkswagen original accesso-  
ries.  
Install the anti-theft wheel bolt according to the  
position marked on the back of the wheel cover.  
·
Tighten screws  
— Tighten the opposite wheel bolts including the  
anti-theft wheel bolt one after the other.  
— Reinstall the cover caps of the wheel bolts or the  
full wheel covers.  
Keep the label with the code number of the  
anti-theft wheel bolts. A replacement upper  
section can be acquired from Volkswagen original  
parts based on this.  
A
B
15 cm  
26 cm  
Position the jack and lift the vehicle  
— Use the jack from the tool kit.  
Changing the wheel and raising the vehicle  
115