Advertisement

Advertisement

Wheels -> Tyre pressure monitor for Your Volkswagen T Cross SUV First Generation (2018-2025)

Tyre pressure  
Tyre pressure monitor  
What you should be mindful of  
NOTICE  
Functionality  
The tyre pressure monitoring indicator indicates  
a change in tyre pressure.  
Always adjust the tyre pressure to the load.  
·
·
Warning when pressure changes  
illuminates  
Check the pressure in all tyres at least once  
a month and before each longer ride.  
— Stop the vehicle.  
Check the pressure when the tyres are cold. Do  
not reduce the higher pressure of warm tyres.  
·
— Check the tyres and tyre pressures.  
After each change in tyre pressure, save the new  
values in the tyre control display.  
·
Show tyres with modified pressure  
Applies to 10Infotainment:  
WARNING  
— Tap on  
.
Risk of an accident!  
— By moving your finger sideways, choose the  
screen with the menu item for the vehicle status.  
If tyre pressure loss is very quick, try to stop the  
·
vehicle carefully without heavy steering or  
heavy braking.  
— Select the menu item for the vehicle status.  
— Select the menu item for the tyres.  
Sticker with prescribed tyre pres-  
sures  
Function restriction  
The system is unable to provide a warning in the  
event of a very rapid tyre pressure loss, e.g. sudden  
puncture.  
The sticker with the prescribed tyre pressure values  
is located in the centre body pillar on the driver’s  
side.  
The system function may be restricted in the follow-  
ing cases:  
— Uneven load on the wheels  
— Sporty driving style  
— Driving on dirt roads  
Saving tyre pressure values  
— Inflate the tyres to the prescribed inflation pres-  
sure.  
A
Information on pressure measurement with cold  
tyres » page 116, What you should be mindful of  
— Turn on the ignition.  
— Store the tyre pressure values in one of the fol-  
lowing ways.  
B
C
D
Tyre pressure value with partial load  
Tyre pressure value with full load  
Prescribed tyre pressure value for the spare  
wheel  
Save tyre pressures with the button  
— Press and hold the button on the button bar.  
E
F
Tyre pressure reading for the front axle tyres  
Tyre pressure reading for the rear axle tyres  
The warning light in the instrument cluster illumi-  
nates  
from the isolation box. After storing the  
tyre pressure values, an acoustic signal sounds  
and the warning light goes out.  
— Release the button  
.
116  
Wheels  
Store the tyre pressure values in the infotainment  
Applies to 10Infotainment:  
— Continue driving, exercising appropriate caution,  
and seek the help of a specialist garage.  
In the following menu, select the menu item for dis-  
playing the vehicle condition:  
— Tap on  
.
Wheel bolt cover caps  
— By moving your finger sideways, choose the  
screen with the menu item for the vehicle status.  
Remove cover caps and install  
— Select the menu item for the vehicle status.  
— Select the menu item for the tyres.  
Disconnecting  
— Press the  
button.  
— Then follow the instructions on the screen.  
In which case the tyre pressure values are to be  
stored  
— Change of tyre pressure  
— Change of one or more wheels  
— Change of position of a wheel on the vehicle  
— Always after covering a distance of 10,000 km or  
once a year  
— Insert the bracket from the tool kit into the recess  
in the cover cap.  
Sticker for storing the tyre pressure values  
— Remove the cover cap.  
The procedure for storing the tyre pressure values is  
also shown on a sticker. It is located on the centre  
body pillar on the driver's side.  
Installing  
— Push the cover cap onto the wheel bolt to the  
stop.  
Full wheel frame  
Removing and installing the trim  
Applies to factory built or original accessory trims  
from Volkswagen.  
Disconnecting  
1
2
Inflating the tyre to the prescribed inflation  
pressure  
— Hang the clamps for removing the wheel trims at  
the edge of one of the openings in the trim.  
Saving the values  
— Push the wheel wrench through the clamp, sup-  
port on the tyre and pull off the wheel trim.  
Installing  
Troubleshooting  
— Press the wheel trim onto the wheel rim at the  
designated valve opening.  
Functional restriction / system fault  
When using an anti-theft wheel bolt, it must be  
located at the location indicated on the bezel.  
flashes for about 1 minute and stays on  
— Stop the vehicle, switch off the ignition  
and start the engine.  
— Press the trim, starting at the valve, into the rim  
on both sides until it engages around the entire  
circumference.  
If the indicator light  
flashes again after  
starting the engine, there is a system error.  
Wheel bolt cover caps  
117