Get Do it yourself -> Bulb replacement Guide for Volkswagen Touran 4 Door Third Generation (2022-2025)

5. Slide a new wiper blade with the same length and design onto the wiper arm in the opposite direction to the

B

A

arrow until it engages → fig. 2

. For this to work, the wiper blade has to be folded out→ fig. 2

.

6. Place the wiper arm carefully on the rear window.

WARNING

Worn or dirty wiper blades reduce visibility and increase the risk of accidents and serious injuries.

● Always clean dirty wiper blades.

● Always replace wiper blades if they are damaged or worn and are no longer cleaning the window glass

sufficiently.

NOTICE

Cleaning wiper blades or door windows with unsuitable cleaning agents may cause damage.

● Do not clean the wiper blades and windshield and windows with fuel, nail polish remover, paint thinner, or other

similar fluids.

● Do not clean the wiper blades with rough sponges or other sharp objects.

If there is wax residue on the windshield and rear window from car wash systems and other products, this

can cause the windshield wipers to rub. Remove any wax residue with a special cleaner or cleaning towels.

Introduction

Before performing bulb replacement, check if it is an incandescent bulb or anLED

light. Generally, light bulbs can be replaced by yourself. Depending on the model and on the vehicle equipment, if the

exterior lighting uses LED technology, it is not possible to replace theLED lights or individual LEDs by yourself. The

malfunction of individual LEDs may be an indication that moreLEDs will malfunction. If this is the case, have theLED

lights checked and replaced if necessary by an authorized Volkswagen dealer or authorized Volkswagen Service

Facility. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized Volkswagen Service

Facility.

Driving with exterior lighting that is inoperative may be against the law.

Additional bulb specifications

Some bulbs may have certain manufacturer specifications that differ from conventional light bulbs. The respective

name will be on the bulb socket or glass bulb.

WARNING

If the vehicle lighting is not used appropriately for the weather conditions, the road will not be illuminated

sufficiently. The vehicle will not be visible to other road users or will be difficult to see. This can cause accidents and

serious or fatal injuries.

● Regularly check the vehicle's lighting system and turn signals.

● Have the vehicle lighting system repaired immediately, when necessary.

WARNING

Work in the hood space can result in accidents and serious injuries if bulb replacements are carried out incorrectly.

● Always follow the tasks described and observe the general safety precautions.

● Never perform a bulb replacement if you are not familiar with the required activities.

● If you are not sure how to carry out a bulb replacement, have the work required carried out by suitably qualified

professionals. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized Volkswagen

Service Facility.

WARNING

During the bulb replacement, the sharp-edged parts of bulb housings and hot or exploding bulbs can cause serious

injuries.

487

● Only change bulbs when they have cooled down completely.

● Always protect your hands during bulb replacement.

NOTICE

Water entering the headlight housing can damage the electrical system.

● Following a bulb replacement, always install the covers on the headlight housing.

● Always check that the covers are properly secured after installation.

NOTICE

If you touch the lights of the glass bulbs when changing them, you may leave fingerprints on the light. The

fingerprints will vaporize from the heat when the light is switched on and will cause the reflector to darken.

● Do not touch the glass bulb with bare fingers. Use cloth gloves, for example.

● Only touch the base of the light when installing it.

Information on bulb replacement

Always perform the following activities for bulb replacement in the specified sequence→

:

1. Safely park the vehicle on a horizontal and firm surface, and a safe distance away from moving traffic where

possible (→ Parking).

2. Set the electronic parking brake.

3. Switch the lights off.

4. Turn off the turn signal if it is activated.

5. Vehicles with an automatic transmission: Engage the parking lock .

6. Switch the ignition off.

7. Vehicles with manual transmission: Select a gear.

8. Allow the orientation lighting to turn off.

9. Allow the affected light bulbs to cool down.

10. Check if you can see that a fuse is burnt out (→ Fuses).

11. Change the affected light bulb according to the instructions→

.

A light bulb may only be replaced with the same type of light bulb. The respective name will be on the bulb

socket or glass bulb.

Do not touch the glass bulbs with your bare fingers. The residue from fingerprints can impair the brightness of

the headlight.

12. Check the bulb function after a bulb is changed.

If the bulb does not function, the bulb may not have been inserted correctly, may have fallen out, or the

connector may not have been plugged in correctly.

13. After every bulb replacement in the front of the vehicle, have the headlight adjustment checked by an

authorized Volkswagen dealer or authorized Volkswagen Service Facility. Volkswagen recommends contacting

an authorized Volkswagen dealer or authorized Volkswagen Service Facility.

WARNING

If the steps described for the bulb replacement are ignored, accidents may occur. Serious injuries may result.

● Always follow the tasks described and observe the general safety precautions.

NOTICE

488

Removing and inserting trim panels and headlights incorrectly can damage the vehicle paint and body.

● Always be careful when removing and inserting the trim panels and headlights.

Replacing bulbs in the headlights (halogen bulbs)

Preparations

Only perform these activities in the specified order:

1. Refer to the information on bulb replacement and carry out the activities.

2. Open the hood.

The headlight does not need to be removed for bulb replacement.

Fig. 1 In the hood space: covers on the back of the right

headlight.

1

2

3

4

Cover for the high beam headlight bulb holder.

Cover for the low beam headlight bulb holder.

Bulb holder for daytime running and parking light.

Cover for the turn signal bulb holder.

Fig. 2 In the hood space: replacing the bulbs in the right

headlight.

489

1

2

3

4

High beam headlight bulb holder.

Low beam headlight bulb holder.

Bulb holder for daytime running and parking light.

Turn signal bulb holder.

Replacing a bulb in a high beam headlight

1

1. Remove the rubber cover on the rear side of the headlight→ fig. 1

.

2. Turn the bulb holder in the direction of the arrow up to the stop and carefully pull out toward the rea→r fig. 2

1

.

3. Replace the burned out bulb with a new bulb that is identical to the one being replaced. If necessary, push the

catch on the bulb holder and pull the bulb straight out of the bulb holder.

4. Insert the bulb holder into the headlight and turn in the opposite direction to the arrow as far as it will go

1

→ fig. 2

.

1

5. Fit the rubber cover on the rear side of the headlight→ fig. 1

6. Close the hood.

.

Replacing a bulb in a low beam headlight

2

1. Remove the rubber cover on the rear side of the headlight→ fig. 1

.

2

2. Push the bulb holder downward in the direction of the arrow and pull it out toward the rear→ fig. 2

.

3. Replace the burned out bulb with a new bulb that is identical to the one being replaced. If necessary, push the

catch on the bulb holder and pull the bulb straight out of the bulb holder.

2

4. Insert the bulb holder in the headlight and push upward in the opposite direction of the arrow→ fig. 2

2

.

5. Fit the rubber cover on the rear side of the headlight→ fig. 1

.

6. Close the hood (→ In the engine compartment).

Replacing the bulb in a daytime running light or parking light

1. Turn the bulb holder in the direction of the arrow up to the stop and carefully pull out toward the rea→r fig. 1

3

.

2. Replace the burned out bulb with a new bulb that is identical to the one being replaced. If necessary, push the

catch on the bulb holder and pull the bulb straight out of the bulb holder.

3. Insert the bulb holder into the headlight and turn in the opposite direction to the arrow as far as it will go

3

→ fig. 2

.

4. Close the hood.

Replacing a bulb in a turn signal

4

1. Remove the rubber cover on the rear side of the headlight→ fig. 1

.

2. Turn the bulb holder in the direction of the arrow up to the stop and carefully pull out toward the rea→r fig. 2

4

.

3. Replace the burned out bulb with a new bulb that is identical to the one being replaced. If necessary, push the

490

catch on the bulb holder and pull the bulb straight out of the bulb holder.

4. Insert the bulb holder into the headlight and turn in the opposite direction to the arrow as far as it will go

4

→ fig. 2

.

4

5. Fit the rubber cover on the rear side of the headlight→ fig. 1

6. Close the hood.

.

The figures show the right headlight. The left headlight is a mirror image of the

right.

It is not possible for you to replace the

LED

s in LED daytime running lights. Contact a suitably qualified professional. Volkswagen recommends contacting an

authorized Volkswagen dealer or authorized Volkswagen Service Facility.

Replacing the bulbs in the front bumper

Preparations

Only perform these activities in the specified order:

1. Refer to the information on bulb replacement and carry out the activities.

2. Turn the steering so that the wheel on the affected vehicle side is pointing toward the center of the vehicle,

start the engine if required.

3. Stop the engine and remove the vehicle key from the ignition lock.

A suitable screwdriver is required for the bulb replacement. The headlight in the front bumper does not need to be

removed for bulb replacement.

Replacing the Bulbs (Fog Lights) in the Front Bumper

Fig. 1 In the front bumper on the right: replacing the bulb

in the headlight.

1

2

Connector.

Bulb holder.

1. Carefully pry off the cover in the direction of the arrow with a suitable screwdriver→ fig. 1.

491

1

2. Release the connector → fig. 1

and disconnect it.

2

3. Turn the bulb holder counterclockwise up to the stop and remove it toward the rear with the bulb→ fig. 1

4. Replace the burned out bulb with a new bulb that is identical to the one being replaced.

5. Insert the bulb holder in the headlight and turn it clockwise until it stops.

.

1

2

6. Plug in the connector → fig. 1

to the bulb holder→ fig. 1

.

The connector must audibly engage→

7. Fit the cover → fig. 1.

.

NOTICE

Water entering the connectors can damage the electrical system.

● When you plug the connector into the bulb holder, make sure that the connector is fitted correctly in the

headlight housing.

NOTICE

Removing and inserting trim panels and headlights incorrectly can damage the vehicle paint and body.

● Always be careful when removing and inserting the trim panels and headlights.

The figures show the right headlight. The left headlight is a mirror image of the

right.

Replacing bulbs in the vehicle body

Preparations

Only perform these activities in the specified order:

1. Refer to the information on bulb replacement and carry out the activities (→ Exterior lighting).

2. Open the trunk lid.

3. Remove the taillight from the vehicle body.

Removing the taillight

Fig. 1 Side of the luggage compartment: removing the

taillight.

492

1

2

3

Connector for taillight.

Catch for the connector.

Fixing screw for taillight.

1. Open the section of the side trim panel in the luggage compartment near the taillight in the direction of the

arrow → fig. 1.

2

2. Pull the red catch for the connector → fig. 1

1

.

3. Pull out the connector → fig. 1

.

3

4. Remove the screw by hand→ fig. 1

.

5. Carefully pull the taillight toward the rear and out of the body.

6. Remove the taillight and place it on a clean, flat surface.

Fig. 2 Taillight in the vehicle body: removing the bulb

holder.

1

Locking tabs of the bulb holder.

Replacing bulbs

1

1. To remove the bulb holder, carefully pry the catch in the direction of the arrow→ fig. 2

2. Take the bulb holder out of the taillight.

.

3. Replace the burned out bulb with a new bulb that is identical to the one being replaced.

4. Insert the bulb holder in the taillight.

All catches must audibly engage.

Installing the taillight

1. Insert the taillight carefully into the opening on the body.

2. Hold the taillight in the installation position with one hand and tighten the screw with the other hand→ fig. 1

3

.

3. Make sure the taillight is installed correctly and is secure.

1

4. Plug in the connector to the bulb holder→ fig. 1

.

493

2

5. Push in the catch → fig. 1

.

6. Close the section of the side trim panel in the luggage compartment near the taillight in the opposite direction

of the arrow.

7. Close the trunk lid.

The illustration shows the left taillight. The right taillight housing is a mirror image of the

left.

There are different versions of the taillights. The locations and versions of the bulb holders and bulbs may

vary from the images.

In LED

taillights, some lighting elements may be equipped with “standard” bulbs. These bulbs can be replaced.

Replacing bulbs in the trunk lid

Preparations

Only perform these activities in the specified order:

1. Refer to the information on bulb replacement and carry out the activities (→ Exterior lighting).

2. Open the trunk lid.

The taillight does not need to be removed from the trunk lid for bulb replacement. A suitable screwdriver is required

to remove the cover.

Replacing bulbs in the taillight

Fig. 1 In the trunk lid: removing the cover.

1

2

Connector fuse.

Taillight connector.

494

Do it yourself -> Bulb replacement for Your Volkswagen Touran 4 Door Third Generation (2022-2025)

Related Topics

Do it yourself

Popular Owner Manuals

Latest Owner Manuals