Get Contact Surface Cleaning Set VAS6410 -> Contact Surface Cleaning Set VAS6410 , Using Guide for Audi A1 SUV 2010-2017

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

3

Contact Surface Cleaning Set -

VAS6410-

⇒ “3.1 Contact Surface Cleaning Set VAS6410 , Using”,

page 169

3.1

Contact Surface Cleaning Set -

VAS6410- , Using

⇒ “3.1.1 General Information”, page 169

⇒ “3.1.2 Wiring Eyelets, Repairing”, page 169

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

⇒ “3.1.3 Threaded Connections, Repairing”, page 171

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

⇒ “3.1.4 Battery Terminal Clamp and Battery Terminal, Cleaning”,

page 172

⇒ “3.1.5 Protecting”, page 173

3.1.1

General Information

The Contact Surface Cleaning Set - VAS6410- makes optimal

repair quality possible in the realm of vehicle electronics. Using

the tools, service work can be performed in the area of the contact

sensor on the threaded connection wiring harnesses in the high

current circuit (starter and charging current). The -VAS6410- is

adapted to the vehicle structural measurements and ensures cor‐

rect servicing and a comfortable procedure.

Note

The illustrations of the service work only serve as examples.

Contact Surface Cleaning Set - VAS6410-

3.1.2

Wiring Eyelets, Repairing

Special tools and workshop equipment required

♦ Torque Wrench 1331 5-50Nm - VAG1331-

Note

♦ Do not use rust remover, contact spray or grease because the

lack of friction will cause the torque to be exceeded when in‐

stalling and this will lead to the threaded connection breaking.

♦ The gray sanding pads are for slight contamination and suit‐

able for "soft surfaces". The red sanding pads are for heavy

contamination and suitable for "hard surfaces".

WARNING

Risk of injury. Observe warning notes and safety precautions.

Refer to ⇒ “1.3 Warnings and Safety Precautions”, page 3

3. Contact Surface Cleaning Set VAS6410

169

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

– Disconnect battery.

– Loosen the cap nut and remove the wiring eyelet from the

threaded connection.

– Check the wiring eyelet for corrosion, contamination, etc.

– Select the corresponding adapter and the corresponding

sanding pad.

Note

The sanding block can be used instead.

Caution

Make sure the tin layer is not worn down too much and the

copper is not visible. A galvanic element can form from this,

destroying the metal and causing incorrect repairs.

Note

Due to the different thicknesses of the tin layer, the cleaning proc‐

ess must be performed in several steps and a visual inspection

of the wiring eyelet between steps is necessary.

– Insert the adapter in the wiring eyelet and sand off the corro‐

sion and contamination with circular motions.

– Check the wiring eyelet and sand it again if necessary.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

170

Rep. Gr.97 - Wires

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

– If necessary, remove the burr on the wiring eyelet with the de‐

burrer.

– Reinstall the wiring eyelet with the specified torque. Refer to

⇒ Wiring diagrams, Troubleshooting & Component locations

Note

Optimal contact is ensured if the bolted components are tightened

to the specified torque after cleaning.

– Apply protection material to the connection. Refer to

⇒ “3.1.5 Protecting”, page 173 .

– Reconnect the battery.

WARNING

Risk of injury. Prior to handling or servicing batteries, read, un‐

derstand and observe the Warning and Safety Measures. Re‐

fer to ⇒ “1.3 Warnings and Safety Precautions”, page 3

– Reprogram the window regulators, enter the radio code, set

the clock and, if necessary, recode the control modules that

have error messages.

3.1.3

Threaded Connections, Repairing

Special tools and workshop equipment required

♦ Torque Wrench 1331 5-50Nm - VAG1331-

Note

♦ Do not use rust remover, contact spray or grease because the

lack of friction will cause the torque to be exceeded when in‐

stalling and this will lead to the threaded connection breaking.

♦ The gray sanding pads are for slight contamination and suit‐

able for "soft surfaces". The red sanding pads are for heavy

contamination and suitable for "hard surfaces".

WARNING

Risk of injury. Prior to handling or servicing batteries, read, un‐

derstand and observe the Warning and Safety Measures. Re‐

fer to ⇒ “1.3 Warnings and Safety Precautions”, page 3

– Disconnect battery.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

3. Contact Surface Cleaning Set VAS6410

171

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

– Loosen the cap nut and remove the wiring eyelet from the

threaded connection.

– Check the threaded connection for corrosion, contamination,

etc.

– Select the corresponding adapter and the corresponding

sanding pad for the threaded connection.

Caution

Make sure the tin layer is not worn down too much and the

copper is not visible. A galvanic element can form from this,

destroying the metal and causing incorrect repairs.

Note

Due to the different thicknesses of the tin layer, the cleaning proc‐

ess must be performed in several steps and a visual inspection

of the wiring eyelet between steps is necessary.

– Place the adapter on the threaded connection and sand off the

corrosion and contaminants with circular movements.

– Check the threaded connection and sand it again if necessary.

– Retighten the connection and, if necessary, the anti-rotation

protection to the specified torque. Refer to ⇒ Wiring diagrams,

Troubleshooting & Component locations.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

Note

Optimal contact is ensured if the bolted components are tightened

to the specified torque after cleaning.

– Apply protection material to the threaded connection. Refer to

⇒ “3.1.5 Protecting”, page 173 .

– Reconnect the battery.

WARNING

Risk of injury. Prior to handling or servicing batteries, read, un‐

derstand and observe the Warning and Safety Measures. Re‐

fer to ⇒ “1.3 Warnings and Safety Precautions”, page 3

– Reprogram the window regulators, enter the radio code, set

the clock and, if necessary, recode control modules that have

error messages.

3.1.4

Battery Terminal Clamp and Battery

Terminal, Cleaning

Special tools and workshop equipment required

♦ Torque Wrench 1331 5-50Nm - VAG1331-

172

Rep. Gr.97 - Wires

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

Note

Do not use rust remover, contact spray or grease because the

lack of friction will cause the torque to be exceeded when instal‐

ling and this will lead to the threaded connection breaking.

WARNING

Risk of injury. Prior to handling or servicing batteries, read, un‐

derstand and observe the Warning and Safety Measures. Re‐

fer to ⇒ “1.3 Warnings and Safety Prec^Pa^rou^teti^co^ten^ds^by”,^cop^pa^yrg^ige^ht.3^{Copying for private or commercial purposes, in part or in whole, is not}

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

– Disconnect battery.

– Check the battery terminal clamp and the battery pole for cor‐

rosion or dirt.

– The battery terminal clamp is cleaned with the battery terminal

cleaner wire brush using circular motions.

– The battery terminal is cleaned with the bottom side of the ter‐

minal cleaner using circular motions.

WARNING

Risk of injury. Prior to handling or servicing batteries, read, un‐

derstand and observe the Warning and Safety Measures. Re‐

fer to ⇒ “1.3 Warnings and Safety Precautions”, page 3

– Reconnect the battery and tighten the terminals to the speci‐

fied torque.

Note

Optimal contact is ensured if the bolted components are tightened

to the specified torque after cleaning.

3.1.5

Protecting

Caution

Missing protection leads to the electrical system damage.

3. Contact Surface Cleaning Set VAS6410

173

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...

Electrical Equipment General Information - Edition 08.2019

Note

♦ All threaded connections must be tightened to the specified

torque.

♦ When applying protection, always use the accompanying hose

on the protection container.

♦ Protection wax is used in the cool area.

♦ Cavity protection wax is used in the warm area.

♦ The protection material draws itself into the affected places by

capillary action.

– Hold the injector under the wiring eyelet and spray all around

the pins.

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not

permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability

with respect to the correctness of information in this document. Copyright by AUDI AG.

– Hold the injector above the wiring eyelet and spray all around

the pins and wiring eyelet.

174

Rep. Gr.97 - Wires

Download User Manual App

Contact Surface Cleaning Set VAS6410 -> Contact Surface Cleaning Set VAS6410 , Using for Your Audi A1 SUV 2010-2017

Related Topics

Special Tools

Revision History

ESD Work Surface VAS6613

Contact Surface Cleaning Set VAS6410

Popular Owner Manuals

Latest Owner Manuals