Get In the event of a breakdown -> Changing a bulb Guide for Citroen Berlingo SUV Third Generation (2018-2025)

In the event of a breakdown

► If your vehicle is so equipped, tighten the

security bolt using the wheelbrace 5 equipped

with a security socket 8.

► Tighten the other bolts using the

wheelbrace 5 only.

Do not exceed the maximum authorised

speed of 50 mph (80 km/h) or the maximum

distance of 50 miles (80 km).

Driving with more than one spare wheel of

this type is prohibited.

Changing a bulb

8

In some weather conditions (e.g. low

temperature or humidity), misting on the

internal surface of the glass of the headlamps

and rear lamps is normal, and will disappear

after the lamps have been on for a few

minutes.

► Store the tools.

The wheel trim from the replaced wheel must

not be reﬁtted.

Fitting a steel spare wheel

Visit a CITROËN dealer or a qualiﬁed

workshop.

Have the tightening of the spare wheel's bolts

and its tyre pressure checked.

Have the punctured tyre examined. After

inspection, the technician will advise you on

whether the tyre can be repaired or if it must

be replaced.

The headlamps have polycarbonate

lenses with a protective coating:

– Do not clean them with a dry or abrasive

cloth, nor with detergent or solvent

products.

If the vehicle is ﬁtted with alloy wheels, the

washers A do not make contact with the steel

spare wheel. The wheel is held in place by

the conical contact surface B of each bolt.

– Use a sponge and soapy water or a pH

neutral product.

– When using a high-pressure washer on

persistent marks, do not keep the lance

directed towards the headlamps, lamps or

their edges for too long, so as not to damage

their protective coating and seals.

Wheel with wheel trim

When reﬁtting the wheel, reﬁt the wheel

trim, starting by aligning the cutout with the

valve and then pushing the trim into place all

round its edge with the palm of your hand.

After changing a wheel

Stow the punctured wheel in the carrier.

With a non-standard spare wheel

Changing a bulb must only be done with

the ignition oﬀ and after the headlamp /

lamp has been switched oﬀ for several

minutes - risk of serious burns!

Do not touch the bulb directly with your

ﬁngers; use a lint-free cloth.

It is essential only to use anti-ultraviolet

(UV) type bulbs, so as not to damage the

headlamp.

Tyre inﬂation pressures are indicated on

this label.

For more information on Identiﬁcation

markings, particularly this label, refer to the

corresponding section.

Deactivate certain driving aid functions

(Active Safety Brake, Adaptive cruise control,

etc.).

209

In the event of a breakdown

Always replace a failed bulb with a new bulb

of the same type and speciﬁcation. To avoid

lighting imbalance, replace the bulbs in pairs.

Model A

Types of bulb

Various types of bulb are ﬁtted on the vehicle. To

remove them:

Opening the bonnet/Accessing the

bulbs

Proceed with caution when the engine is hot -

risk of burns!

Take care with objects or clothing that could

be caught in the blades of the cooling fan -

risk of strangulation!

Type A All-glass bulb: pull gently as it is ﬁtted by

pressure.

Type B Bayonet bulb: press on the bulb then

turn it anti-clockwise.

Type C Halogen bulb: release the retaining

spring from its housing.

Halogen bulbs (Hx)

Model B

To ensure good quality lighting, check

that the bulb is correctly positioned in its

housing.

After changing a bulb

To reﬁt, carry out the operations in

reverse order to removal.

Type D Halogen bulb: turn the bulb

anti-clockwise.

Close the protective cover very carefully to

guarantee the sealing of the lamps.

When each operation has been

completed, check the operation of the

lighting.

Light-emitting diode (LED)

headlamps and lamps

Front lamps

For more information on Changing a bulb

and, in particular, the types of bulb, refer to the

corresponding section.

1. Sidelamps/Daytime running lamps

Type A, W21/5W or LED (depending on

version)

Depending on version, the aﬀected types of

headlamps/lamps are:

– Daytime running lamps/sidelamps.

2. Main beam headlamps

Type C, H1

If you need to replace this type of bulb,

you must contact a CITROËN dealer or a

qualiﬁed workshop.

210

In the event of a breakdown

► Remove the bulb and replace it.

Dipped beam headlamps

Type C, H7

3. Dipped beam headlamps

Type C, H7

4. Direction indicator

Type B, PY21W

5. Foglamp

8

Take care to reposition the protective

cover while keeping the tab accessible.

Sidelamps/Daytime running lamps

Type D, H11

Type A, W21/5W

Model A

Direction indicator side repeater

Type A, WY5W-5W (amber)

► Turn the connector a quarter turn clockwise.

► Pull the bulb connector.

► Remove the bulb and replace it.

Model B

– Push the repeater towards the rear and

release it.

– When reﬁtting, engage the repeater towards

the front and then slide it backwards.

Amber coloured bulbs (direction indicators and

side repeaters) must be replaced with bulbs of

identical speciﬁcation and colour.

Light-emitting diodes (LEDs)

If you need to replace this type of bulb,

you must contact a CITROËN dealer or a

qualiﬁed workshop.

► Remove the protective cover by pulling on

the tab.

► Turn the unit in relation to the support.

► Pull the bulb connector.

211

In the event of a breakdown

Main beam headlamps

Type C, H1

Take care to reposition the protective

cover while keeping the tab accessible.

► Pull the unit in relation to the support.

► Remove the bulb and replace it.

Front foglamps

Direction indicators

Type B, PY21W

Type D, H11

Model A

Rapid ﬂashing of a direction indicator

lamp (left or right) indicates that one of

the bulbs on the corresponding side has

failed.

Model A

Model B

► Insert a ﬂat screwdriver between the lamp

and the cover.

Model B

► Pull and lever to unclip the cover.

► Remove the protective cover by pulling on

the tab.

► Unclip the unit in relation to the support.

► Pull the bulb connector.

► Remove the two fastening screws of the

module.

► Remove the module from its housing.

► Turn the connector a quarter turn

anti-clockwise.

► Remove the bulb and replace it.

212

In the event of a breakdown

With side-hinged doors/tailgate

8

► Remove the two ﬁxing bolts using the Torx

key provided in your vehicle.

For more information on the Tool kit, please

refer to the corresponding section.

► From the outside, pull the whole lamp unit

towards you (with side-hinged doors) or

towards the centre of the vehicle (with tailgate).

► Press the locking clip and disconnect the

connector.

► Turn the bulb holder a quarter turn

anti-clockwise.

► Remove the bulb holder.

► Replace the faulty bulb.

1. Brake lamps/sidelamps.

Type B, P21/5W

2. Direction indicators.

Type B, PY21W (amber)

3. Reversing lamps.

Type B, P21W

To replace these bulbs, it is possible to

contact a CITROËN dealer or a qualiﬁed

workshop.

4. Foglamps.

Type B, P21W

Rear lamps

For more information on Changing a bulb

and, in particular, the types of bulb, refer to the

corresponding section.

► Open the tabs, then pull out the lamp holder.

► Remove the faulty bulb by pressing lightly on

it while turning it a quarter turn anti-clockwise.

► Replace the bulb.

Take care to reposition the tabs and the

wiring correctly to avoid trapping the

wire.

► From the inside, disconnect the electrical

connector at the rear of the lamps.

213

In the event of a breakdown

After changing a rear direction indicator

bulb, the reinitialisation time is

approximately 2 minutes or more.

► Change the bulb.

► Reposition the plastic lens and press it in.

Installing electrical accessories

The vehicle's electrical system is

designed to operate with standard or optional

equipment.

Before ﬁtting other electrical equipment

or accessories to your vehicle, contact a

CITROËN dealer or a qualiﬁed workshop.

Third brake lamp

Type A, W16W - 16W

Number plate lamps

Type A, W5W - 5W

With side-hinged doors

CITROËN accepts no responsibility for

the cost incurred in repairing the vehicle

or for rectifying malfunctions resulting from

the installation of accessories not supplied or

not recommended by CITROËN and not

installed in accordance with its

recommendations, in particular when the

combined power consumption of all of the

additional equipment connected exceeds 10

milliamperes.

► Unclip the interior trim.

► Disconnect the connector by moving aside

its tab.

► Turn the bulb holder a quarter turn

anti-clockwise.

► Change the bulb.

► Put the bulb holder back in place and

reconnect the connector.

– Unscrew the two nuts.

– Push the rods.

– If necessary, disconnect the connector to

remove the lamp.

– Replace the bulb.

12 V battery / Accessory

battery

Procedure for starting the engine using another

battery or for charging a discharged battery.

Fuses

► Put the trim back in place.

Changing a fuse

With tailgate

All work must be carried out only by a

CITROËN dealer or a qualiﬁed workshop

The replacement of a fuse by a third party

could cause a serious malfunction of the

vehicle.

Lead-acid starter batteries

These batteries contain harmful

substances (sulphuric acid and lead).

They must be disposed of in accordance

with regulations and must never under any

► Move aside the plastic lens using a

screwdriver.

214

In the event of a breakdown -> Changing a bulb for Your Citroen Berlingo SUV Third Generation (2018-2025)

Related Topics

In the event of a breakdown

Popular Owner Manuals

Latest Owner Manuals