Get In the event of a breakdown -> Temporary puncture repair kit Guide for Citroen Berlingo SUV Third Generation (2018-2025)

In the event of a breakdown

All of these tools are speciﬁc to your

vehicle and may vary depending on

equipment.

power supply for long enough to repair a tyre

after a puncture.

Do not use them for any other purposes.

Only the 12 V socket located at the front

of the vehicle can be used to power the

compressor.

The jack must only be used to change a

wheel with a damaged or punctured tyre.

The jack does not require any maintenance.

The jack meets European standards, as

deﬁned in the Machinery Directive 2006/42/

EC.

For more information on the Tool kit,

refer to the corresponding section.

► Connect the pipe from the bottle of sealant to

the valve of the tyre to be repaired and tighten

ﬁrmly.

► Connect the pipe from the compressor to the

bottle of sealant.

► Check that the compressor switch is in

position "O".

► Fully uncoil the electric cable stowed under

the compressor.

Repair procedure

Some parts of the jack such as the

screws and hinges could cause injury:

avoid touching them.

Do not remove any foreign body

(e.g. nail, screw) which has penetrated

the tyre.

Carefully remove any traces of grease.

► Park the vehicle without obstructing traﬃc

and apply the parking brake.

► Follow the safety instructions (hazard

warning lamps, warning triangle, high visibility

jacket, etc.) according to the legislation in force

in the country in which you are driving.

► Switch the ignition oﬀ.

Temporary puncture

repair kit

► Connect the compressor's electric plug to the

vehicle's 12 V socket.

► Aﬃx the speed limit sticker.

Scan the QR Code on page 3 to view

explanatory videos.

► Remove the valve cap from the tyre to be

repaired, and place it in a clean place.

Made up of a compressor and a sealant

cartridge, it allows you to carry out a temporary

repair of the tyre so that you can drive to the

nearest garage.

It is designed to repair most punctures located

on the tyre tread.

The speed limit sticker must be aﬃxed

inside the vehicle in the area close to the

driver, to remind them that a wheel is in

temporary use.

► Switch the ignition on.

The vehicle's electric system allows the

connection of the compressor to the 12 V

204

In the event of a breakdown

After use, do not discard the bottle into the

environment; take it to a CITROËN dealer or

an authorised waste disposal site.

Do not forget to obtain a new bottle of

sealant, available from a CITROËN dealer or

a qualiﬁed workshop.

Checking/adjusting tyre

pressures

The compressor can be used, without injecting

sealant, to check and, if necessary, adjust the

tyre pressures.

► Switch on the compressor by moving the

switch to position "I" until the tyre pressure

reaches 2 bar. The sealant product is injected

under pressure into the tyre; do not disconnect

the pipe from the valve during this operation (risk

of blowback).

► Remove the valve cap from the tyre and keep

it in a clean place.

► Uncoil the pipe stowed under the compressor.

► Screw the pipe onto the valve and tighten

ﬁrmly.

► Check that the compressor switch is in

position "O".

► Fully uncoil the electric cable stowed under

the compressor.

► Connect the compressor's electric plug to the

vehicle's 12 V socket.

► Switch the ignition on.

► Start the compressor by placing the switch at

position "I" and adjust the pressure to the value

shown on the vehicle's tyre pressure label. To

deﬂate: press the black button located on the

compressor pipe, near the valve connection.

If after approximately 7 minutes, the

pressure of 2 bar is not reached, this

indicates that the tyre is not repairable;

contact a CITROËN dealer or a qualiﬁed

workshop for assistance.

► Drive immediately for approximately 3 miles

(5 kilometres) at reduced speed (between

12 and 37 mph (20 and 60 km/h)) to plug the

puncture.

► Stop to check the repair and the tyre

pressure using the kit.

► Move the switch to position "O".

► Disconnect the compressor's electric plug

from the vehicle's 12 V socket.

► Remove the kit.

► Reﬁt the cap on the valve.

With a tyre repaired using this type of kit,

do not exceed a speed of 50 mph

(80 km/h) and do not drive more than

50 miles (80 km).

You must contact a CITROËN dealer or a

qualiﬁed workshop to have the repair checked

and the tyre changed.

► Remove and store the bottle of sealant.

If after 7 minutes the pressure of 2 bar is

not reached, the tyre is damaged;

contact a CITROËN dealer or a qualiﬁed

workshop for assistance.

The sealant product is harmful if

swallowed and causes irritation to the

eyes.

Keep this product out of the reach of children.

The use-by date of the ﬂuid is marked on the

bottle.

► Once the correct pressure is reached, put the

switch in position "O".

► Remove the kit and stow it.

► Reﬁt the cap on the valve.

205

In the event of a breakdown

Should the pressure of one or more tyres

be adjusted, it is necessary to reinitialise

the under-inﬂation detection system.

For more information on Tyre under-inﬂation

detection, refer to the corresponding section.

► Slacken the bolt using the wheelbrace until

the carrier is low enough to allow the carrier

hook to be disengaged.

Spare wheel

► If the vehicle is ﬁtted with a towbar, raise

the rear of the vehicle using the jack (must be

at jacking point B) to allow suﬃcient space to

remove the spare wheel.

Scan the QR Code on page 3 to view

explanatory videos.

For more information on the Tool kit,

Removing the spare wheel from the

carrier

► Depending on version, open the tailgate or

side-hinged doors.

refer to the corresponding section.

► Park the vehicle without obstructing traﬃc

and apply the parking brake.

► Follow the safety instructions (hazard

warning lamps, warning triangle, wearing high

visibility jacket, etc.) according to the legislation

in force in the country in which you are driving.

► Switch the ignition oﬀ.

► Release the carrier from the hook and

place the spare wheel next to the wheel to be

changed.

Accessing the spare wheel

► Access to the spare wheel is from the rear.

► Access the carrier bolt, located on the rear

door sill.

206

In the event of a breakdown -> Temporary puncture repair kit for Your Citroen Berlingo SUV Third Generation (2018-2025)

Related Topics

In the event of a breakdown

Popular Owner Manuals

Latest Owner Manuals